WiFI extremely slow in Arch

I have a new install of Arch after deciding to give it a go after 6 or 7 years on Gentoo.
The only problem I am experiencing is extremely slow internet. 1.58Mbps vs 31Mbps previously in Gentoo.
Google seems to indicate a lot of people have similar issues with Arch, but having followed the Wiki to the letter and not finding any solutions on Google I am stuck at where to start.
iw dev
phy#0
Interface wlp0s29u1u5
ifindex 3
wdev 0x1
addr c4:3d:c7:ca:85:02
type managed
channel 1 (2412 MHz), width: 20 MHz, center1: 2412 MHz
Please let me know what logs to upload, any assistance appreciated. I will continue to search myself.

If you are using a USB WiFi device that can potentially change names with different ports, it would probably make sense to either create a persistent name for that particular piece of hardware, or go back to the old naming scheme if you don't have another wireless card.  The idea of these crazy names is that if you have two wireless cards, two ethernet cards, or even an ethernet card and a broadcom wireless card (which also uses the eth* namespace), you will never know which will be 0 and which will be 1.  But if you tell the system what to name them, then you can at least have your netctl service run on a given interface name and know what it is going to be.
Having said all that, you should also be aware that other network management solutions deal with changing interface names much better then netctl.  Netctl needs the interface name to be specified in the profile, so if it changes you are kind sh*t out of luck until you make the manual changes necessary. 
To see if you have multiple network management services trying to handle things, run "systemctl --type=service" to see all the services you have going.  If you see more than one that should be handling the network (for example, if you enabled [email protected] during setup) then you need to figure out which single management solution is going to best fit your use case and go with that one only.  Most commonly, people still ahve dhcpcd.service or dhcpcd@<interface>.service around.  But it is also not uncommon to see people with netctl-ifplugd@<interface>.service running along with netctl-auto@<interface> at the same time, which will also cause issues.

Similar Messages

  • Wifi extremely slow after Windows 10 Upgrade

    After upgrading to Windows 10 my wifi connection is extremely slow.  I updated all the Lenovo drivers after the upgrade and it hasn't helped. The listed network driver is 2x2 11b/g/n Wireless LAN M.2 Adapter.  I've included screenshot below of a speedtest on the same network between my T440s and my smartphone.  The smartphone results are what should be expected on the laptop.  T440s Speed Test Samsung S6 Speed Test When observing the task manager there are no other programs utilizing the network.    

    I had the same problem.
    After trying many suggestions on the internet I found one that solved my problem. I took more than a week to solve but now I'm happy.
    On my case the problem was the security wifi protocol. I was using AES and changed to TKIP. For me there is no reason to this to work, but solved my problem.
    Hope it helps.

  • BIG PROBLEM with Lenovo A320 wifi - extremly slow

    Hello Lenovo community,
    I have a big problem with my lenovo A320 all in one.
    The wifi connection is extremly slow. I have 3 differen devices at the same place one macbook, one phone and my lenovo a 320 connectet to the same wifi. The macbook and phone get about 50mpbs but my lenovo gets only about 0.3 to 2 mbps. I have tested it wit different networks and differnet routers but is always very very slow.
    When connected via LAN works fast and well but via wifi its useless.
    I have the intel core I3 and Broadcom 802.11n with the newest drviers.
    I have tried everything possible but nowthing helped.
    Can you please help me with any solution ?
    Thank you in forward

    Thats great news for you.. it probally is a defect on my phone, I purchased it new from apple and tommorrow its going in for service..
    I have seen others with similar issues, must be a bacth, I even heard that there are 2 wifi antenas that were used on them, one of them gives problems the other not...
    Just a shame, its a great phone
    thanks for all the feedback

  • WiFi extremely slow

    When I am connected to a wifi network it is very slow. Most of the time EDGE is faster. I am having trouble loading pages on safari, loading youtube videos and browsing iTunes. Why would WiFi be so slow?

    WiFi should be about 5 times faster. There is a test you can run on Safari on your iPhone that clocks your connection speed of both WiFi and Edge and compares them to their database of speeds: http://iphonenetworktest.com. WiFi is typically around 1000 while Edge is around 200. See what it is to determine if WiFi is the problem.
    Is this problem on one particular WiFi connection or on all? Panera, which was one of the first companies to offer free WiFi, is so popular that their WiFi typically runs in the the 200 range, while my antique airport mushroom connected to cable at home can run well over 1000.
    Kevin

  • Podcasts downloads over WIFI EXTREMELY SLOW on iPhone 4 & 5

    IPhone 5 - podcast app - 26mb episode = 20+ minutes over WIFI
    Why is it soon slow???!!!
    I use the same wifi for other downloads and streaming iTunes so it is definitely not network issue
    Furthermore on the same iPhone other apps and content download fast over the same network
    Why would apple limit download speed or not be capable to fix this for so long???!!!
    This issue is very old (+18 months) and it kills experience

    I would blame iOS 5. It's software is a lot to handle on a simple 1-core, A4 pocessor. The nanno's simple software makes syncing much quicker with fewer steps. If you really wan't your music on fast, you can just reduce their quality a little.
    Thank you for choosing Apple.

  • Wifi extremly slow when held horizontal dreath grip on 4S

    Hi
    When you hold the iphone 4s horizontal the wifi conection drops down to 1 bar or disconects totaly form wifi.
    I have been told that the wifi antena is on top part beside the camara lens, if cover with your hand the phone loses wifi completly.
    I have a router in the same room and when held horizontal the wifi goes down to 1 bar cant download nothing, horrible.
    I have contacted apple on this problem, I sending it in to be check, This cant be happing,,, before the dreath grip and now this.....???
    have any other noticed this problem ?? all fedback is greatly appriciated.
    Thanks to all

    Thats great news for you.. it probally is a defect on my phone, I purchased it new from apple and tommorrow its going in for service..
    I have seen others with similar issues, must be a bacth, I even heard that there are 2 wifi antenas that were used on them, one of them gives problems the other not...
    Just a shame, its a great phone
    thanks for all the feedback

  • Wifi extremely slow when not right next to the router?

    Hey,
    bought a new macbook air last week with Mountain Lion (I've fully updated it) and it seems to be having a few wi-fi problems. Although wifi speed is fine when in the same room as the router, the speed drops of significantly when in just the next room, and even small sites take about 10 seconds to load. I'm using an Virgin Media 54g router but the problem remains the same with a Belkin 54g router as well. The recieved speed in my room (a couple of floors up admittedly) is 11 and speedtest.net shows a 0.05mbps download speed and (strangely) a 1mbps upload speed when I can connect at all.I haven't yet had the oppurtunity to try n or 5ghz routers, but as the rest of the network uses the Virgin Media one, I'd like to be able to reliably connect to this.
    I've tried suggestions online such as creating a new location, disabling bluetooth, tried a new user, a new router and renewing DHCP lease etc. but nothing seems to work.
    Does anyone have any suggestions to try? I'm not sure if this is a software or hardware issue, but I thought this was the most appropriate place to put this.
    Thanks in advance,
    George Bryan

    It's normal, of course, for Wi-Fi performance to fall off with distance between the client and the access point. Whether your MBA is performing normally can only be determined by taking it to an Apple Store or AASP for testing.

  • Ipad mini with retina wifi extremely slow/dead after ios 8 update

    Just updated my devices to iOS 8. Im having no issues with the Iphone 5s wifi works perfectly fine. But with the Ipad Mini w/ Retina I can't get any wifi. Its connected, I've reset the wifi & router. But my mini keeps saying there isnt any internet connection. Anyone else have this issue?

    After updating my iPhone 4s that worked absolutely fine, i set about my iPAD 2,
    took forever for the request made icon change to down loading, then installing. Once completed i had severe connection issues, Safari not finding servers, iOS telling me my password was incorrect so real problems, i could not even populate the BBC news app it just stuck as did Ebay, Amazon, Maplin etc Apps...
    Not one to panic but terrified because i'm off on holiday for a week to Spain on Saturday, i use my iPad to remote my PC and remote assistance to systems i fit, and i have several hundred pages in Notes which i use as 'sticky's'.so do i need this like a hole in the head?
    tried several reboots, eventually last resort before defaulting and clearing it out, and restoring, fearing loosing those precious notes (not certain they were all backed up), I reset my network settings (which wipes all stored login details for various sites, resets WiFi details etc),
    To my Massive relief it cured all the connection problems i was having, so for some reason something must have corrupted.
    you need to know what details you used on each site you use.
    suggest you all try it
    Other suggestion is you do need a lot of spare memory space, so park large files onto PC in alternative cloud storage, then delete from your device. You can restore deleted apps afik no are charged again, so delete those your not really using making sure you keep the data safe.
    hope it helps
    Alan

  • Airport express extending wifi extremely slow

    Hello,
    I have a time capsule creating a wireless network and a airport express extending the wireless network.
    When I'm connected to the time capsule I have around 12mbp of speed but when I am connected to the airport express I have around 0.2mbp
    In the airport utility it says the connection is good she connected to the airport express.
    Everything was working fine a few days ago.
    I was reading the the forum that it may be interference from a neighbour and to change the channel but I can fine where to change the channel. 
    Is changing the channel the solution? How can I access where to change the channel?
    Or is there another solution?
    Anyone knows how to fix this speed problem in airport express?
    Cheers
    Francisco

    What is the distance between the Time Capsule (TC) and the AirPort Express Base Station (AX)? Are they in the same room, different room, different floor from each other? If in different rooms/floors, what is the basic building material used in the walls/floors/ceilings?
    It is important to understand that the AX can only extend the TC's wireless network at the same bandwidth that it receives it. If you are only getting around .2 Mbps at the AX, then either there is too much distance between routers or there is some form of Wi-Fi interference (other Wi-Fis or the builiding material) between them that is preventing the AX from getting a strong enough signal to extend.
    Changing channels is one possible solution. You would do so using the AirPort Utility. If you are using version 5.x of that utility, you would change channels as follows: AirPort Utility > Select the AX > Manual Setup > AirPort > Wireless tab > Channel. By default Channel is set to "Automatic." Click on the up/down arrow to the right of the Channel window to get the other channel options.
    If this doesn't resolve the problem, please check out the following AirPort User Tip for details on how to best place each base station for maximum bandwidth in an extended network.

  • Extremely slow internet using wifi.

    Hi guys,
    First post here so be gentle.
    After a week or so of using Arch I started noticing some strange things happening so far:
    - Pacman's package list downloading from the repos happens at regular speed (around 700Kb/s), then followed by a 30 secs lag between each package download, which starts at normal speed, but then come down to around 2Kb/s then I get an Address Record error, which terminates the download.
    - first ping to google is fine, then any ping after either get a 'host unknown' error or ping takes around 9Kms.
    - another strange behavior that happens when pinging is that the wireless connection start at a bit-rate of 1Mb/s (according to iwconfig), then every time I ping google the bit-rate jumps (1Mb/s -> 12Mb/s -> 24Mb/s -> 54Mb/s -> 81Mb/s).
    - can't load any websites (google takes around 5min to load, most other sites I just get a timed out error)
    So my config is as follows:
    - Intel Centerino Ultimate-N 6300
    - connected using NetworkManager (but while connected with wicd the problem still occurs).
    - running gnome 3.
    - the router is Edimax 6524n
    So far, I've checked resovle.conf (which only states my router ip address, which is fine because it serves as my DNS server), my hosts file (which is configured according to the tutorial in ArchWiki) and I've disabled the ipv6 module.
    I've asked in several forums so far but with not much success, so i'm really hoping someone can solve it for me.
    Thanks in advance!
    PS: in one of the forums i asked someone asked me to post the output of dmesg | grep -i iwlagn, so here it is:
    pastebin.com/Pmhi6swv
    PS2: This problem does not occur in any of the Windows machines that are connected to the wireless network nor does it happen when this exact machine runs Windows; so the problem is definitely in Linux
    Last edited by gzaidman (2011-06-01 20:18:37)

    I'm kind of having a similar problem. Ever since upgrading to 2.6.39 my wifi is extremely slow. It connects in g mode according to iwconfig and other network analyzing programs. I have iwl3945. The problem is. First it connects to wifi network(which takes about 30secs to successfully complete a connection request) it works great and I'm measuring 25Mbit(which is my internet connection speed) on speedtest.net. But after some minutes my speed drops to around 100KB/s and has a slight fluctuation, not quite constant. Even the upload is bigger than the download speed. If I disconnect the wifi, reload the kernel module and reconnect, then it works again for 1-2 minutes at full speed, then the speed drops again.
    http://www.speedtest.net/result/1338532978.png
    Any suggestions, or ideas would be very helpful. Thank you.
    btw. I use NetworkManager and kernel 2.6.39
    iwconfig output:
    wlan0     IEEE 802.11abg  ESSID:"Kozma2" 
              Mode:Managed  Frequency:2.442 GHz  Access Point: 00:23:54:14:CE:E6   
              Bit Rate=54 Mb/s   Tx-Power=15 dBm   
              Retry  long limit:7   RTS thr:off   Fragment thr:off
              Power Management:off
              Link Quality=50/70  Signal level=-60 dBm 
              Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
              Tx excessive retries:0  Invalid misc:37462   Missed beacon:0

  • MBP 5.1 I have a recent problem with airport connectivity. ethernet connection is working fine, but wifi has become extremely slow and bad functioning. signal is received, no problem with the wlan (my husband 's wifi with MBP is perfect) please help

    I have a MBP 5.1 with snow leopard 10.6.8. It has been working fine until few days ago, when it started to have different problems:
    1) airport is not working well. it is extremely slow, has difficulties in fully loading pages, looses connectivity, It is not browser related, behaves thesame in safari or firefox; it is not the router/wlan; my husband mbp wifi works fine (as it was mine...) and iphone wifi is also working fine. it sees the signal and different networks. , it is also very very slow in opening skype (after that, it is working ok) if  I connect via ethernet cable to the same router, everything works perfectly and with the correct speed.could it be a damaged airport card? a software problem/corruption? logic board? (I hope not, the computer is out of apple care now....)
    2) after a certain time (more than hours) of use, the trackpad is behaving strangly, increase sensitivity to touch, unwanted selection of folders, files and text or images in web pages when i move the cursor, the cursor jumping all over the places while writing, ecc I have the impression it starts doing that when I use heavily the CPU ( and the temperature goes up). Is this again a problem of the mother/logic board?
    I had recently serviced it since it was not booting properly, but except some permissions repaired, they did noit find anything wrong in the hard drive (which I have  now substituted with a SSD) or other hardware.
    thanks in advance for any help/suggestions
    alessandra

    I think I solved the wifi connection problem, just by switching off completely the router! sounds trivial, but in this case it worked!!!
    the funny behaviour of the trackpad/cursor still persists. any suggestion???
    thanks again

  • Wifi unstable and extremely slow on my Aspire V Nitro VN7-591G-7.

    Hi again ! My previous problem is now solved. But now I have issues with my wifi. The wifi works perfectly on other devices but on my Aspire V Nitro VN7-591G-7, it's just impossible to do anything on the internet... I've read it's a common problem and there are solutions. What steps should I follow in order to solve this ? I'm running Windows 8.1 by the way. I really like the performances of this computer so I wish to get rid of this stupid problem ! Thank you very much.

    Can you describe "unstable and extremely slow" in more detail. Are you connected to the 5 GHz band of your wireless router or are you connected to the 2.4 GHz band? Are you having problems with all websites or just a few? Which web browser are you using?  IE or chrome or firefox? What is the model # of your wireless router? Is your wireless router supplied by your ISP? Or did you buy it retail? What BIOS version is currently installed on you laptop? What BIOS version is designated as the latest version on Acer's website? Does the problem occur when you use other people's wifi such as a friend, relative or neighbor?  Have you tested it somewhere besides your home? Does Acer's website list an updated wireless driver for your computer? http://us.acer.com/ac/en/US/content/drivers

  • My new ipod is extremely slow, but i have full strength wifi. Works fast at others homes.

    My new ipod touch 4g is extremly slow in my house, but i have full strength wifi. Works fast at others homes. When i try to connect to the internet it gives me a server error. All other ipods and laptops work fine in the home. Does anybody else have this issue?

    Have you tried powering off and then back on your router?
    You can try:
    - Reseting the iPod. Nothing will be lost
    Reset iPod touch:  Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    -Resetting network settings: Settings>General>Reset>Reset Network settings.

  • Wifi is extremely SLOW

    I'm not sure what's going on. My wifi is extremely slow. I know it's not the network, I have a PC hooked up via ethernet and it runs fast/normal. I also have a NAS on it, and the drives are mounted, sometimes. Often, it'll fail to make a connection to them. Again, the NAS shows up fine on the PC. I'm not sure why my macbook pro has such slow wifi; my previous mac ran fine and I haven't tinkered with anything in the network.

    Quote from: Rostan;108703
    I have two routers both work fine. Only thing that has issues is the GS60 and GS70
    Updating firmware can solve/improve the compatibility issue.
    Quote from: Rostan;108706
    This guy is in the process of trouble shooting an issue with the Drivers and has not found a solution so there is nothing useful from this.
    Changing wifi connection to 802.11a/5GHz band can improve the download speed. I'd give that a try.
    The last issue he has is that his home router doesn't support 802.11a.

  • Ipad Air is extremely slow on wifi. Ipad 1 worked fine.

    My Ipad Air wifi is extremely slow. I have seen online this is an issue. I have read responses but still confused. Ipad 1 worked fine.

    Some things to try first:
    1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    4. Go into your router security settings and change from WEP to WPA with AES.
    5.  Renew IP Address: (especially if you are droping internet connection)
        •    Launch Settings app
        •    Tap on Wi-Fi
        •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
        •    In the window that opens, tap on the Renew Lease button
    6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
    http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
    ~~~~~~~~~~~~~~~~~~~~~~~~~
    Some things to try first:
    1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    4. Go into your router security settings and change from WEP to WPA with AES.
    5.  Renew IP Address: (especially if you are droping internet connection)
        •    Launch Settings app
        •    Tap on Wi-Fi
        •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
        •    In the window that opens, tap on the Renew Lease button
    6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
    http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
    ~~~~~~~~~~~~~~~~~~~~~~~~~
    Fix WiFi Issue for iOS 7
    http://ipadnerds.com/fix-wifi-issue-ios-7/
    Fix WiFi Issue for iOS 7
    http://ipadnerds.com/fix-wifi-issue-ios-7/
    iOS 6 Wifi Problems/Fixes
    Wi-Fi Fix for iOS 6
    https://discussions.apple.com/thread/4823738?tstart=240
    How To: Workaround iPad Wi-Fi Issues
    http://www.theipadfan.com/workaround-ipad-wifi-issues/
    Another Fix For iOS 6 WiFi Problems
    http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
    Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    How to Boost Your Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
    Troubleshooting a Weak Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
    How to Fix a Poor Wi-Fi Signal on Your iPad
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
    iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
    How to Fix: My iPad Won't Connect to WiFi
    http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
    iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Connect iPad to Wi-Fi (with troubleshooting info)
    http://thehowto.wikidot.com/wifi-connect-ipad
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    Some Wi-Fi losses may stem from a problematic interaction between Wi-Fi and cellular data connections. Numerous users have found that turning off Cellular Data in Settings gets their Wi-Fi working again.
    You may have many apps open which can possibly cause the slowdown and possibly the loss of wifi. In iOS 4-6 double tap your Home button & at the bottom of the screen you will see the icons of all open apps. Close those you are not using by pressing on an icon until all icons wiggle - then tap the minus sign. For iOS 7 users, there’s an easy way to see which apps are open in order to close them. By double-tapping the home button on your iPhone or iPad, the new multitasking feature in iOS 7 shows full page previews of all your open apps. Simply scroll horizontally to see all your apps, and close the apps with a simple flick towards the top of the screen.
    Wi-Fi or Bluetooth settings grayed out or dim
    http://support.apple.com/kb/TS1559
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

Maybe you are looking for

  • How do I Pass a parameter to a SQL Component Task where the source SQL statement is also a variable

    Hi, I have been tasked with making a complex package more generic. To achieve this I need to pass a parameter to a SQL Component Task where the source SQL statement is also a variable. So to help articulate my question further I have create a package

  • Using cue points in Flash CS5 to trigger actions

    Hi there, I'm looking to use a cue point in a video to trigger an action, in this case go to and play at a movie clip on the stage. Is this possible. My setup is as follows: I've a video on stage with the instance name 'vid', with a cue point 'lap1'

  • Can't delete slide show from catalog in PSE 6

    I am a fairly new user of PSE working in a Windows Vista environment.  When I right click on the thumbnail of an unwanted slideshow in PSE 6 and select "Delete from Catalog" I get the message "An error occurred while reading files or writing files to

  • Issue iwth generic Datasource -Urgent Help

    HI All, I needed to create a generic DataSource through view . The view is created successfully however I have some dependant key figure in view such as Tips amount referring to MSEG(Referring Table ) _WAERS (Referred field name.) because of which I

  • My Primary DC is down

    Hi all my Primary DC has been down since yesterday due to a hardware failure and should be back up on friday, already started having issues with users not been able to logon with error "Cannot not establish trust relationship". From research I have t