Will our existing drivers work with LabVIEW 8.x?

We have drivers for some of our DAQ products that were developed in LabVIEW 6 or 7.
Is there any reason these drivers would not work with the latest versions of LabVIEW?
We ask because there seem to be some customers in Europe who believe our drivers do not work with LabVIEW 8.5, but we know there are users with LabVIEW 8.0 and 8.1 using the drivers without problems.
Any thoughts or suggestions, or are there any known issues with older drivers in LabVIEW 8.5?
Regards,
Roger Hammerquist

Hi Roger,
In general, the latest versions of LabVIEW will work with older
versions of the DAQ drivers. However, it is certainly possible that some of
the older drivers could have some conflicts.
How “old” are the driver versions that your customers are
using? Specifically, what version of the
driver does your customer report seeing the errors with? Is the
customer using the same operating system that the original program was written
for? Is the customer seeing problems
upgrading the VIs from LabVIEW 6 or 7 to LabVIEW 8.5?
The suggestion to work with someone to try it out is excellent.
Posting the specific driver versions
seeing the conflict, might also shed some light on the issue.
Jared T.

Similar Messages

Will the ELVIS board work with LabVIEW 2010 Student Edition?

I recently acquired a traditional ELVIS board (with the PCI DAQ board). So far I've only installed the evaluation for LabVIEW 2010 (x64), and when I attempt to install the ELVIS Traditional 3.0.5 software I get the following message: "This installer requires LabVIEW 8.5 Full Development system or later to be present on this computer. LabVIEW Base Development System in any version of LabVIEW is not supported. Please install LabVIEW and then run the NI ELVIS installer again."
I am eligible to purchase a student license for LabVIEW 2010 and would like to know if the ELVIS Traditional 3.0.5 software will install after I've acquired a student license.
I am running windows 7 (x64) with an evaluation version of LabVIEW 2010 (x64).
Solved!
Go to Solution.

Perhaps I spoke too soon. I purchased a student license for LabVIEW 2010 and am still receiving the same error. I've provided screenshots of my license and the message from the ELVIS Traditional 3.0.5 installer.

Will hardware drivers work with the run-time engine or only a full version of Labview?

Hello.
I'm trying to get a quatech I/O card to work. The instructions with the drivers we were given state "you must have labview installed before installing these drivers".
A program I wrote on my machine works fine with those drivers and does toggle outputs on the card, but when I build it into an executable on our test unit (doesn't have a full version of Labview, just the Run-Time engine) the card doesn't work.
We installed the run-time engine on the unit, then the drivers.
I guess my question is: Do most drivers work with both the full version of Labview and the run-time engine? Or do I need to somehow 'convert' these drivers to work with the run-time engine?
Th
anks for your help!
Dave Neumann
[email protected]

Dave:
I can't determine which dll is required but if there are more than one that
shipped with the quatech I/O card try to placing one dll at a time in the
same directory as the exe so that you can determine which one is the
required one. If that doesn't do it then it may need more than jsut one of
the dlls so placing all that came with the quatech I/O card s/w driver
package in the same directory as the exe should do the trick.
Best of luck.
-Tom
"Neumannium" wrote in message
news:[email protected]..
> Tom,
>
> Thanks for your reply. One of the problems I'm having is figuring out
> which .dll I would need to include (I'm not a software guy).
>
> Would the .dll your speaking of be different th
an the one which is
> installed with the drivers? I'm looking at a .dll that is installed
> when you install the labview drivers for this card, but the run-time
> engine still doesn't want to get the card to work. (The file installed
> when I install the drivers is called 'daqlv32.dll' and I don't know
> how to find any other .dll's I might need)
>
> Actually, it appears the card 'is' being seen by the run-time engine,
> but I'm getting impulses rather than distinct changes of state.
>
> Anyway, thanks for the help.
>
> Dave Neumann
> [email protected]

Will this power supply work with my PC?

Will this power supply work with my PC? I have a Compaq Presario SR5816F
http://www.newegg.com/Product/Product.aspx?Item=9SIA4CP1GF8726&cm_re=power_supplies_500w-_-9SIA4CP1G...
http://www.amazon.com/Solid-Gear-Series-ATX12V-SDGR-500BX/dp/B00FF7VEJE
This question was solved.
View Solution.

JCGood1984, welcome to the forum.
The computer should take a standard ATX power supply unit (PSU). I suggest measuring the existing PSU and compare the measurements to the one in the links. If the measurements are the same, it should fit. I don't know anything about the brand, however.
Please click the "Thumbs up + button" if I have helped you and click "Accept as Solution" if your problem is solved.
Signature:
HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
HP Photosmart 7520 AIO
++++++++++++++++++
**Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
Intelligence is God given; Wisdom is the sum of our mistakes!
I am not an HP employee.

Where can I found hardware to get analog signal from VCR and work with labview and then sample this signal in very high frequency?

I am trying to build a Digital Video Recorder using Labview. The problem is that I found that Labview sample the signal in the order of milisecond. I wanted it to be in the order of microseconds. Also I am looking for a cheap Hardware solution if it is possible

Your question does not make a lot of sense to me, so I will just point out a few things.
1. The PCI-1411 works well with VCR signals. It has a BNC connector as well as a S-Video connector. The price is under $1000, so it is fairly reasonable. The amount of time you save getting it to work with LabVIEW is worth any extra cost.
2. The PCI-1411 is sampling three colors at 30 frames per second, with an image resolution of 640x480. This is the best resolution you are likely to get from a VCR signal. The sampling rate for each byte in the image is about 28 MB/sec. This is in the microsecond range that you are looking for, I think. If you are only interested in the raw signal instead of the image, you could look at the high speed digitizing boards NI sell
s that acquire at higher rates.
If this information isn't really what you were looking for, perhaps you could clarify your question.
Bruce
Bruce Ammons
Ammons Engineering

Looking for a way to get my Product ID and Vendor ID so I can enable my Radium 49 USB MIDI keyboard to work with Labview 7

Looking for the Product ID and Vendor ID for my Radium 49 USB MIDI keyboard to work with Labview 7
Is there a tool to find out the Vendor ID and Product ID for a USB device?
Example: of what I'm looking for
The Product ID for National Instruments DAQPad-6020E is 0x12C0. The
USB vendor ID is 0x3923. This is a 16-bit hexadecimal number(1093)
(that is decimal 4243).
Thanks for all the fast responses this newsgroup RULES!!!!!!!!!!!!

http://digital.ni.com/public.nsf/allkb/335A90747734097886257070006415B9
How To Find The Vendor and Product ID for USB Devices?
Primary Software: Driver Software>>NI-VISA
Primary Software Version: 3.3.1
Primary Software Fixed Version: N/A
Secondary Software: N/A
Problem:
I want to make an NI-VISA driver that requires the vendor and product ID?
Solution:
There is a utility called USBView,
free from Windows, attached below, which you can use to view what is
connected to your computer's USB ports. It is necessary to load this
program and connect the USB device in development. Upon selecting the
device in USBView, one can then look on the right side of the
application window to obtain the Product ID and Vendor ID. This will
allow you to enter in the correct IDs when creating a driver .inf file
when using the VISA Driver Development Wizard. For more information
about how to use the VISA Driver Development Wizard see the related
links below.
Note: It is necessary to keep the hexadecimal
(0x####) format. Do not remove the "0x" hexadecimal format preceding
the ID number.

Will hp officejetpro 6830 work with windows 10?

will hp officejetpro 6830 work with windows 10?

Windows 10 is still in th pre-release stage and it is not published yet what will be supported, I expect this will happen in the next month as the July 29 release nears. HP's site here will have compatibility information, check back in late July for information. That said, I would expect that current printers will be suported in Windows 10. The current public Windows 10 Build 10130 does have a Fax driver for the Officejet Pro 6830 and print drivers that would be compatible as well.

Will weblogic 4.5 work with the Sun Java Servlet Development Kit Version 2.1?

          Will weblogic 4.5 work with the Sun Java Servlet Development Kit Version 2.1
          (JSDK 2.1). The reason I want this is we want our application servlets to
          use the new 2.1 redirection mechanism to redirect to JSP files.


WL 4.5 supports JSP 1.0 (and, therefore Servlet 2.1).
          What I want to know is when will it support JSP 1.1 (and, therefore Servlet
          2.2)!
          Regards,
          Murali Krishna Devarakonda
          Cox News <[email protected]> wrote in message
          news:7rk40p$s00$[email protected]..
          >
          > Will weblogic 4.5 work with the Sun Java Servlet Development Kit Version
          2.1
          > (JSDK 2.1). The reason I want this is we want our application servlets to
          > use the new 2.1 redirection mechanism to redirect to JSP files.
          >
          >
          >
          >

Will my ipod classic work with windows 8

I am finally updating my Windows XP desktop to a Windows 8 laptop. Will my ipod classic work with Windows 8? I've seen a ton of problems from other users with regard to compatibility.

Do yourself a big favor. Switch to Windows 7. (Or buy a Mac.)

Will the Linksys WRT160N work with windows vista at all?

Will the Linksys WRT160N work with windows vista at all?
Some one please clear this up for me, it could be answered in the simplestterms from the English Language of course.
I've recently purchased the Linksys WRT160N however after purchase "of course"I manage to find reviews stating that the router will not work with the WindowsVista Premium, or windows Vista for that matter.
E.g.(Comments like These 'which are not my own')----------
"When I tried it with a new computer running Vista 64, it would install but the Linksys System Advisor would not. After 1 chat and 4 phone calls with support the system will still not run."
"It is a good product with XP, but if you use Vista 64 good luck. After several hours of working to get it running my patience and options have run out."
"It has taken almost a week for us to figure out that the Linksys Router, WRT160N from Best Buy does not workwith Vista Premium. I looked on-line to Linksys Website and discovered that the router, WRT160N is notsupported for Vista users. .."
E.g. (CommentContradicting to what has been said above)------
"Bought this to replace my outdated Linksys (new Vista laptop) and was blown away. Thisthing practically set itself up. It replaced the wired router and wireless routers I was using, asthe signal strength is awesome. I'm still pulling over 5meg ... "
So I guess one could see why I am confused, based on the 2 sidedcontradictions pertaining to this router actually working with windows vista ornot.
So can someone respond (preferable a Vista User) and tell me the truth as of towhat this router can an cannot do in terms of Vista? Thanks

It should work with vista without any issues if you are running any software on the computers (64 bit) from linksys it may not work but if you will connect that computer with an ethernet to the router it should work fine.

Will a WRE54G repeater work with a WRT160N router?

I'm using a WRT160N router and only getting 2 bars out of 5; fair signal. A friend has offered to sell me a WRE54G range expander. Will a G repeater work with an N router?

Yes,the WRE54G should work with WRT160N...You need to match all the wireless settings of the router to the range expander and it should work then.

HT4059 Will iBook Author books work with an iPad 1?

Will iBook Author books work with an iPad 1?

Look at these.
http://bluemic.com/snowball/
http://www.lifeisaprayer.com/articles/photography/iphone-4-ipad-external-mic-aud io-input
 Cheers, Tom

Will the Cinema Display work with an older MacBook Air?

My wife has an older MacBook Air (circa late 2009) with one USB 2.0 port and one Mini Display port. Will the Cinema display work with this model Air?

It looks to me like the cinema display is a DVI connection. If you have a MiniDisplay port to DVI adapter that connected the MBpro to the display then you have everything you need. (plus a DVI cable). The MDP adapter plugs into the Thunderbolt port of the MBair.

Will Microsoft Office 2001 work with the Lion upgrade?

Will Microsoft Office 2001 work with the Lion upgrade?
Will one have to reinstall after the Lion upgrade?

Office 2001 will not work with Lion. That is a Power PC App which is no longer supprted in Lion. You should upgrade to Office 2011, Apple iWork, or Open Office.

Will "BW 3.1" work with ECC 6.0 ??--------its urgent

One client is using BW 3.1 version. He wants to upgrade SAP from version 4.7 to ECC 6.0
But he does not want to upgrade BW right now.
1) Will "BW 3.1" work with ECC 6.0 ??
2) Do we have to upgrade BW also? Is it mandatory or we can avoid it?
You may get the information on SAP website or 'bw user community'
regards
Pushkar
Regards

Hi Pushkar,
You've posted this on a forum dedicated to development of SAP's Business One product, which is not related to R3 or A1. I recommend you repost your question on one of the R3 forums (options on the left hand menu).
Kind Regards,
Owen
P.S. Please don't use the word 'Urgent' on these forums. It just annoys people and is more likely to get your answer ignored than answered.

Will our existing drivers work with LabVIEW 8.x?

Similar Messages

Maybe you are looking for