Win 7 wifi causes my WRT54G to slow down 20x till reset
My wrt54g (firmware old - v1.00.6) has run fine for years until my daughter got a laptop with win7. All my other systems still run XP or win2k. I only run wireless with her win7 and one netbook with xp, all the other connections are wired.
Going to speedtest.net and after I reset (pull power) the router, I get 20Mbps download. After the win7 wifi runs for a bit, download speed drops to 2 Mbps or less. It seems to be after she goes to you tube and starts watching videos. If I reset again, it immediately goes back to the full speed of 20. I measure this after she's taken her laptop off the network. So, whatever her win7 is doing, it stays that way after she disconnects (i.e. slow on my other systems) until the reset. I also measured the speed on her win7 system and it also would slow there as well and speed up after a reset (for a while).
Any ideas here? Would a newer firmware fix this? I read somewhere that some settings in win7 can fix this, but couldn't find out what they were.
It would greatly help that the router’s needs a firmware upgrade and a reset since you are experiencing intermittent connection. By the way, were you experiencing this problem on both wireless computers or only on the win 7 laptop? If the problem is only with the win 7 laptop, then you might need to update the drivers of the win 7 laptop wireless adapter. If in case that the problem is with both computers then you need to optimize the wireless performance of the router. You can use this tool: : http://www.metageek.net/products/inssider/ to select the best channel that you can use on your router and then check if the router’s wireless performance will improve.
Similar Messages
-
After upgrading from Snow Leopard to Mountain Lion, and setting the text preference, Middle Eastern, causes Photoshop CS6 to slow down. Can this be fixed?
I'm Win, not Mac, but I do have a couple saved messages
Mac 10.8.3 Bug w/Encore and BluRay http://forums.adobe.com/thread/1198709
-create folder not ISO http://forums.adobe.com/thread/1216127 -
I am having issues related to storage and I believe this is causing my computer to slow down. "Other" files part is the major occupier(180 GB). I have done Omni disk and multiple other cleaning(iTunes-device, restart, etc), yet have not been able to empty any more space, nor to speed up my computer? Any suggestions? All your contributions are welcomed. Thanks. Mehmet Mazhar Celikoyar
Below is the result:
Hardware Information:
MacBook Pro (15-inch, Mid 2009)
MacBook Pro - model: MacBookPro5,3
1 3.06 GHz Intel Core 2 Duo CPU: 2 cores
4 GB RAM
Video Information:
NVIDIA GeForce 9400M - VRAM: 256 MB
NVIDIA GeForce 9600M GT - VRAM: 512 MB
Audio Plug-ins:
BluetoothAudioPlugIn: Version: 1.0
AirPlay: Version: 1.9
AppleAVBAudio: Version: 2.0.0
iSightAudio: Version: 7.7.3
Startup Items:
HP IO - Path: /Library/StartupItems/HP IO
System Software:
OS X 10.9 (13A603) - Uptime: 3 days 22:8:6
Disk Information:
ST9500420ASG disk0 : (500.11 GB)
EFI (disk0s1) <not mounted>: 209.7 MB
Macintosh HD (disk0s2) /: 499.25 GB (220.49 GB free)
Recovery HD (disk0s3) <not mounted>: 650 MB
HL-DT-ST DVDRW GS23N
USB Information:
Apple Inc. Built-in iSight
Apple Internal Memory Card Reader
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Computer, Inc. IR Receiver
Apple Inc. BRCM2046 Hub
Apple Inc. Bluetooth USB Host Controller
FireWire Information:
Thunderbolt Information:
Kernel Extensions:
com.rim.driver.BlackBerryUSBDriverInt (0.0.64)
com.livedrive.filesystems.livedrivefs (2.1.14)
Problem System Launch Daemons:
Problem System Launch Agents:
Launch Daemons:
[loaded] com.adobe.fpsaud.plist
[loaded] com.adobe.versioncueCS4.plist
[loaded] com.creativebe.MainMenuHelper.plist
[loaded] com.macpaw.CleanMyMac2.Agent.plist
[loaded] com.magican.castle.plist
[loaded] com.microsoft.office.licensing.helper.plist
[loaded] com.rim.BBDaemon.plist
[failed] com.zeobit.MacKeeper.plugin.AntiTheft.daemon.plist
Launch Agents:
[loaded] com.adobe.CS4ServiceManager.plist
[loaded] com.hp.messagecenter.launcher.plist
[loaded] com.hp.productresearch.plist
[loaded] com.rim.BBLaunchAgent.plist
User Launch Agents:
[loaded] com.adobe.ARM.[...].plist
[failed] com.macpaw.CleanMyMac2Helper.diskSpaceWatcher.plist
[failed] com.macpaw.CleanMyMac2Helper.scheduledScan.plist
[failed] com.macpaw.CleanMyMac2Helper.trashWatcher.plist
[failed] com.UninstallerTool.plist
[failed] com.VolumeWatcherTool.plist
[failed] com.zeobit.MacKeeper.Helper.plist
User Login Items:
BlackBerry Device Manager
HP Scheduler
3rd Party Preference Panes:
Adobe Version Cue CS4
DC30 Xact Driver Panel
Flash Player
Flip4Mac WMV
Perian
Internet Plug-ins:
AdobePDFViewer.plugin
AdobePDFViewerNPAPI.plugin
Default Browser.plugin
Flash Player.plugin
FlashPlayer-10.6.plugin
Flip4Mac WMV Plugin.plugin
iPhotoPhotocast.plugin
JavaAppletPlugin.plugin
OfficeLiveBrowserPlugin.plugin
QuickTime Plugin.plugin
SharePointBrowserPlugin.plugin
Silverlight.plugin
User Internet Plug-ins:
OctoshapeWeb.plugin
Bad Fonts:
None
Time Machine:
Mobile backups: OFF
Auto backup: NO
Volumes being backed up:
Macintosh HD: Disk size: 499.25 GB Disk used: 278.75 GB
Destinations:
TOSHIBA EXT [Local] (Last used)
Total size: 2 TB
Total number of backups: 5
Oldest backup: 2013-10-24 23:21:31 +0000
Last backup: 2013-10-25 02:59:08 +0000
Size of backup disk: Excellent
Backup size 2 TB > (Disk size 499.25 GB X 3)
Top Processes by CPU:
3% WindowServer
1% EtreCheck
1% Microsoft PowerPoint
0% BBLaunchAgent
0% fontd
0% aosnotifyd
Top Processes by Memory:
168 MB Microsoft PowerPoint
123 MB Safari
86 MB Mail
74 MB WindowServer
45 MB com.apple.WebKit.Networking
45 MB com.apple.WebKit.WebContent
41 MB Finder
41 MB PluginProcess
41 MB mds_stores
33 MB Notes
Virtual Memory Statistics:
72 MB Free RAM
1.27 GB Active RAM
1.24 GB Inactive RAM
667 MB Wired RAM
2.58 GB Page-ins
111 MB Page-outs -
Hello, I'm pretty sure my fan on my 2009 mac book pro has stopped running. Would this cause the computer to slow down and take for ever to boot up and show the color wheel every time I select an application ? how involved to replace fan ? cost ?
thanksNot directly, but if the CPU overheats because of incompatible software, that would cause slowdowns. Do not allow the computer to run if the fan is not working unless you wish to fry your motherboard. Please make a Genius Appointment and take it in for service.
-
Wetransfer js error causes my computer to slow down
Every time I send a file via WeTransfer I end up with a js error and then my MacBook Pro slows down to a grinding halt...literally. You can hear the hard drive grinding away. Every time I try to move the mouse or select a file or drop down I get the beachball which will hang for about 10-15 seconds before anything happens. I end up having to shut down all my programs and restarting to get the laptop back to normal. This only happens with WeTransfer. Any ideas what I can do to resolve the issue other than not using WeTransfer?
First my computer turns off and goes black, then this window shows up...
After that this shows up after typing in my password on the log in page...
If I leave the HD plugged in after clicking either response the computer will just shut down again.
If I unplug the HD this window shows up explaining the problem... -
GE60 fan problem. speeds up and slows down constantly [EC reset done]
My model is GE60 OCN and bios and EC is the newest ones for win7 embeded on msi website.
I have the same problem with others if you search here 'ge60 fan'.
The temperature between 50~60℃ the fans runs slow and really quite.
But if the temperature goes down under about 46℃, it speed up and slows down constantly and it is annoying and much noiser.
I think msi should provide new EC firmware for this. Even the temperature is low, it annoys and nosier than when the temperature is between 50~60℃.
Please check this problem and provide new EC firmware for fan policy.
Someone has uploaded video link: youtube.com/watch?v=OQjjjVOpsEQ
this is exact problem with me as well.I have exactly the same problem. Let's continue in the other thread (https://forum-en.msi.com/index.php?topic=165613.0)
-
I have a WRT54GS connected to 2 Ethernet-wired PCs and 2 powerline-connected PCs. Most of the time, it is just used by an Ethernet-wired PC sitting next to it. I subscribe to Yahoo SBCGlobal DSL (now owned by AT&T) with a SpeedStream 5100 DSL modem.
Every few hours hours, the connection speed slows drastically, sometimes to well below dial-up speed (SBCGlobal has a site where you can test your connection rate). It does not speed up by itself. By setting up the router again, powering down and up the router, modem, and the computer -- I have not yet figured out yet exactly what fixes the problem -- eventually I can get the connection back up to DSL speed.
I believe the problem is specific to the router, because I never have a speed problem when the DSL modem is directly hooked up to the PC next to it.
I have verified that I have the latest version of router firmware, and I have used Linksys's EasyConnection diagnostics, which says everything is ok. I have read through the Linksys online docs and the messages on this forum, but I have not figured out the problem yet.
Any help would be greatly appreciated. Please keep in mind that this is problem with a wired, not a wireless, PC connection. Thanks in advance.Hi… I think you should try reducing the MTU on the router to 1400 or 1300. If you still face the same problem, upgrade the firmware of the router.
-
Dimension Security causing SSAS cube to slow down
Hi,
Experiencing problems with with the SSAS cube once its processed. Sometimes takes around 20 mins for the excel to load once you drag down any dimension.The cube has got no calc scripts/named sets etc.It has around 17 dimensions and one dimension(Employer)
has got 46 attributes and another (member)17.Others are pretty small.The Employer dimension is used twice as role playing and the both employer/member have got dimension security applied to it.There are about 6 roles have been set up to restrict access to
members in these dimensions.
The SQL profiler shows multiple "Query Dimension" (mostly for Employer dimension)followed by a lot of "Calculate Non Empty Current"s .Suspect that the delay is due to the dimension security expression evaluation.This only happens
during first access of the cube within a role and it's relatively quick when I'm accessing via a role which doesn't have dimension security applied to it.Is there anyway to automatically trigger this process right after the cube has been processed so that
it doesn't cause agony to the first user?You could build a cache warmer that connects with EffectiveUserName=YourDomain\user1 on the connection string and loop through each user. But what is your dimension security expression? Maybe we can speed it up.
http://artisconsulting.com/Blogs/GregGalloway -
WRT54G V6 slowing down network
Hi, a week ago there was a lightning storm around the area where I live. After the storm passed, my router has been acting weird. I've called my ISP (optimum online) and they did tests on my connection. When my computer is direct connected, the internet is fine, but when I'm connected through the router, the whole network lags. I have a WRT54G v6 with firmware version 1.02.2 and I am on a Dell xps with windows xp. During certain times of the day, my network lags and sometimes its fine. Please help, thanks.
Message Edited by etorix on 07-14-2007 08:21 AMchange the MTU settings on the router to 1452 ..
and does it happen on only the wired or wireless or both ?? -
ListCellRenderer causing extra looping and slow down, please help
Guys
Please could you kindly help me with my long-lasting problem
concerning ListCellRenderer.
I sent it originally to Programming Essentials but no replies at all:
http://forums.sun.com/thread.jspa?threadID=5388059&tstart=15
Here is more detailed description of my problem that did not fit to my original posting (chech link above):
For your convenience I made a special simplified version of my problem.
Here are two fully compilable java-files that indicate my problem with simple GUI and System.out.print output. Please try to run my program, please.
I try use ListCellRenderer and ListSelectionListener with a simple interactive list that contains four names, either male or female names, like:
Bill
James
Martin
Peter
With a simple button "Change gender" the names can be changes to female names, and then again male names, etc...
If you select THE FIRST NAME in the list and press "Change gender" button, the System.print.out shows unnecessarily repeating loops.These accumulating extra loops slow seriously down performance with long lists.
Example output (the first name selected, so accumulating extra loops!!):
Entering method ChangeGender
ChengeGender method (name, index): Bill, 0
Cell renderer (name, index): Bill, 0
ChengeGender method (name, index): James, 1
Cell renderer (name, index): Bill, 0
Cell renderer (name, index): James, 1
ChengeGender method (name, index): Martin, 2
Cell renderer (name, index): Bill, 0
Cell renderer (name, index): James, 1
Cell renderer (name, index): Martin, 2
ChengeGender method (name, index): Peter, 3
Cell renderer (name, index): Bill, 0
Cell renderer (name, index): James, 1
Cell renderer (name, index): Martin, 2
Cell renderer (name, index): Peter, 3
Quitting method ChangeGender
However, if you select OTHER NAMES THAN THE FIRST ONE (or no names at all) and press "Change gender", then no extra loops occur in System.out.print. Why?
Example output (the second name selected, so no extra loops):
Entering method ChangeGender
ChengeGender method (name, index): Bill, 0
ChengeGender method (name, index): James, 1
ChengeGender method (name, index): Martin, 2
ChengeGender method (name, index): Peter, 3
Cell renderer (name, index): Bill, 0
Cell renderer (name, index): James, 1
Cell renderer (name, index): Martin, 2
Cell renderer (name, index): Peter, 3
Quitting method ChangeGender
I will have list containing hundreds of names and therefore extra loops slow severely my application.
Please explain how to avoid extra loops, also when the first name is selected.
And please - if just possible - show me exactly which rows of my program must be rewritten and how.
Thank you very much!Change
for (int counter = 0 ; counter < names.length; counter++) {
defaultListModel.addElement(names[counter]);
}to
ListDataListener[] listeners = defaultListModel.getListDataListeners();
for(ListDataListener listener : listeners) {
defaultListModel.removeListDataListener(listener);
for (int counter = 0; counter < names.length; counter++) {
defaultListModel.addElement(names[counter]);
ListDataEvent evt = new ListDataEvent(defaultListModel,
ListDataEvent.INTERVAL_ADDED,0,names.length-1);
for(ListDataListener listener : listeners) {
defaultListModel.addListDataListener(listener);
listener.intervalAdded(evt);
} -
However I do believe the hard drive had other issues that just might have been further compromised by downloading 5. Talked to a couple of others who have also had bad problems after downloading 5 and that is what really concerns me is that my problem is not isolated. I have just got my computer back up and running and am very concerned about continuing with the 5 upgrade that was automatically downloaded and will be installed the next time I start up. How do I prevent the download from installing upon start up next time until I can get some clearer info on why 5 is causing some problems and can avoid them?
My mother just had this problem. After uninstalling a bunch of search malware, i was still seeing the bing tab come up on start up. The way I fixed this is to delete any shortcuts, remove it from the task bar and the start menu list. It appears this crappy malware modified the firefox and chrome(if installed) shortcuts to open bing.
Of course another way is to modify the shortcuts to remove the link that they added. It was easier for me to remove and just re-pin.
Hopefully that solves your problem too. -
Where clause causing a query to slow down in a cursor
I have a table "the_table" with about 10,000 rows and four columns (id, description, inventory, and category).
This query returns all rows immediately:
select id
, description
, inventory
from the_table
where category = nvl(null, category);
However, when it is put into a cursor, like this:
(p_user_category is a user-defined variable which can be null if the user wants all of the rows)
c_results sys_refcursor;
open c_results for
select id
, description
, inventory
from the_table
where category = nvl(p_user_category, category);
fetch c_results into v_id, v_description, v_inventory;
close c_results;
then it takes five minutes to return even just one row when p_user_category is null.
However, if I change the where clause to:
where (p_user_category is null or category = p_user_category)
then it returns all rows immediately.
It started being a problem right around the time of the most recent update - I am running 11.2.0.2.0 (64-bit production).The optimizer is smart enough to recognise that null is null, so "nvl(null,category)" collapses to "category", and your predicate "category = nvl(null, category)" is transformed to "category is not null" (if it's allowed to be null) or simply disappears - so the SQL test is not the same as the PL/SQL run.
In PL/SQL your manual rewrite is not logicall the same as the original unless you have declared category to be non-null because your first disjunct will allow rows with a null category to be reported, while the original query would lose them.
Check the execution plans for the SQL and the PL/SQL versions.
Regards
Jonathan Lewis
http://jonathanlewis.wordpress.com
Now on Twitter: @jloracle -
RMI server causes the system to slow down and crash with socketException
Hi,
My RMI server application is a simple rmi server which invokes a JNI method once when I invoke through my client application. Server is left as it is after invoking the JNI method. After around 12 hours, server stops running with the following exception
ZoneInfo: C:\Program Files\Java\jre1.6.0\lib\zi\ZoneInfoMappi
ngs (Insufficient system resources exist to complete the requested service)
ZoneInfo: C:\Program Files\Java\jre1.6.0\lib\zi\ZoneInfoMappings (Insufficient s
ystem resources exist to complete the requested service)
Dec 29, 2008 10:09:34 AM sun.rmi.transport.tcp.TCPTransport$AcceptLoop executeAc
ceptLoop
WARNING: RMI TCP Accept-0: accept loop for ServerSocket[addr=0.0.0.0/0.0.0.0,por
t=0,localport=2161] throws
java.net.SocketException: socket closed
at java.net.PlainSocketImpl.socketAccept(Native Method)
at java.net.PlainSocketImpl.accept(Unknown Source)
at java.net.ServerSocket.implAccept(Unknown Source)
at java.net.ServerSocket.accept(Unknown Source)
at sun.rmi.transport.tcp.TCPTransport$AcceptLoop.executeAcceptLoop(Unkno
wn Source)
at sun.rmi.transport.tcp.TCPTransport$AcceptLoop.run(Unknown Source)
at java.lang.Thread.run(Unknown Source)
Dec 29, 2008 10:10:35 AM sun.rmi.transport.tcp.TCPTransport$AcceptLoop executeAc
ceptLoop
WARNING: RMI TCP Accept-0: accept loop for ServerSocket[addr=0.0.0.0/0.0.0.0,por
t=0,localport=2161] throws
java.net.SocketException: socket closed
at java.net.PlainSocketImpl.socketAccept(Native Method)
at java.net.PlainSocketImpl.accept(Unknown Source)
at java.net.ServerSocket.implAccept(Unknown Source)
at java.net.ServerSocket.accept(Unknown Source)
at sun.rmi.transport.tcp.TCPTransport$AcceptLoop.executeAcceptLoop(Unkno
wn Source)
at sun.rmi.transport.tcp.TCPTransport$AcceptLoop.run(Unknown Source)
at java.lang.Thread.run(Unknown Source)
Dec 29, 2008 10:12:36 AM sun.rmi.transport.tcp.TCPTransport$AcceptLoop executeAc
ceptLoop
WARNING: RMI TCP Accept-0: accept loop for ServerSocket[addr=0.0.0.0/0.0.0.0,por
t=0,localport=2161] throws
java.net.SocketException: socket closed
at java.net.PlainSocketImpl.socketAccept(Native Method)
at java.net.PlainSocketImpl.accept(Unknown Source)
at java.net.ServerSocket.implAccept(Unknown Source)
at java.net.ServerSocket.accept(Unknown Source)
at sun.rmi.transport.tcp.TCPTransport$AcceptLoop.executeAcceptLoop(Unkno
wn Source)
at sun.rmi.transport.tcp.TCPTransport$AcceptLoop.run(Unknown Source)
at java.lang.Thread.run(Unknown Source)
Dec 29, 2008 10:15:37 AM sun.rmi.transport.tcp.TCPTransport$AcceptLoop executeAc
ceptLoop
WARNING: RMI TCP Accept-0: accept loop for ServerSocket[addr=0.0.0.0/0.0.0.0,por
t=0,localport=2161] throws
java.net.SocketException: socket closed
at java.net.PlainSocketImpl.socketAccept(Native Method)
at java.net.PlainSocketImpl.accept(Unknown Source)
at java.net.ServerSocket.implAccept(Unknown Source)
at java.net.ServerSocket.accept(Unknown Source)
at sun.rmi.transport.tcp.TCPTransport$AcceptLoop.executeAcceptLoop(Unkno
wn Source)
at sun.rmi.transport.tcp.TCPTransport$AcceptLoop.run(Unknown Source)
at java.lang.Thread.run(Unknown Source)
Dec 29, 2008 10:20:40 AM sun.rmi.transport.tcp.TCPTransport$AcceptLoop executeAc
ceptLoop
WARNING: RMI TCP Accept-0: accept loop for ServerSocket[addr=0.0.0.0/0.0.0.0,por
t=0,localport=2161] throws
java.net.SocketException: socket closed
at java.net.PlainSocketImpl.socketAccept(Native Method)
at java.net.PlainSocketImpl.accept(Unknown Source)
at java.net.ServerSocket.implAccept(Unknown Source)
at java.net.ServerSocket.accept(Unknown Source)
at sun.rmi.transport.tcp.TCPTransport$AcceptLoop.executeAcceptLoop(Unkno
wn Source)
at sun.rmi.transport.tcp.TCPTransport$AcceptLoop.run(Unknown Source)
at java.lang.Thread.run(Unknown Source)
# An unexpected error has been detected by Java Runtime Environment:
# Internal Error (4D555445583F57494E13120E4350500075), pid=1352, tid=1828
# Java VM: Java HotSpot(TM) Client VM (1.6.0-b105 mixed mode, sharing)
# Can not save log file, dump to screen..
# An unexpected error has been detected by Java Runtime Environment:
# Internal Error (4D555445583F57494E13120E4350500075), pid=1352, tid=1828
# Java VM: Java HotSpot(TM) Client VM (1.6.0-b105 mixed mode, sharing)
# If you would like to submit a bug report, please visit:
# http://java.sun.com/webapps/bugreport/crash.jsp
Does anyone has any idea?
Regards
NidhinYour RMI server invokes a JNI method as you mentioned. It seems your system resource is become very low as from the exception from "ZoneInfoMappi"
(Insufficient system resources exist to complete the requested service...I would suggest the following
1- remove the JNI method invocation and replace by a simple method which does nothing special ( counting etc..)
2- Run the RMI sever and stress test it again
If you see the RMI server is working well after 12 hours, then your native method is leaking i.e consuming the system resources ( RAM etc..)
You should profile the running RMI server using jconsole
Regards,
Alan Mehio -
Help! Flashvars causing browser slow down
Hi All,
I have a very simple .swf file that is causing some kind of
slow down or memory leak. It is effecting the browser its self as
moving the mouse cursor around or selecting text becomes sluggish.
Within the .swf, the stage is only 1px by 1px. It is meant to
fit the size of the html element its embedded in. Once the .swf
loads it adjusts its stage to the new dimensions. It then draws a
rectangle movie clip to fit the new size.
Once the rectangle is drawn the .swf then draws 50 circles of
varying size to animate as a snow effect. I wasn't having any slow
down until I added this snow effect in. However let me explain in
the next paragraph that the snow is not the real culprit.
The rectangles fill, stroke, and corner radius. Can all be
set by variables sent to the swf. by the Flashvars attribute of
object, and embed. Once they are retrieved by the .swf they are
processed by a conditional statement I wrote. If one of the
attributes isn't set they are set to a default. The code is
attached below.
Heres how I know the snow effect isn't the culprit. If I
don't pass the .swf any Flashvars attribute and just let it use the
defaults for styleObj in the .swf. The effect runs fine. If I do
try to pass it Flashvars the slow down occurs. Is there an issue
with my conditional statements?
I have tried embedding using the SwfObject.js Class and using
standard HTML tags. Both display the same issue if Flashvars are
passed there's a slowdown if not its fine.
If anyone could help with this, or shoot me some links with
info I would be eternally grateful. I can also provide the source
files if you want to take a look at it.
I have uploaded a test page so you can see the problem in
http://www.callmekev.com/client/test/Hey kglad,
Thanks for all your help. I had the issue posted on 2 other
forums and you are the only response I have got. I was unaware of
the data-type functions you had listed. After some further testing
I found that they had the same effect as using the - operator like
I had been doing.
I did find a solution however. I took the variables as they
were coming in from the Flashvars attribute and saved them in new
flash only variables as numbers. Then I assigned the Flashvars
variables a value of null. I think the .swf was continully going
back to the html variables causing the slow down and this gave it
its on set to look at.
You can check the new
test its a lot smoother. -
Sudden slow down after an auto-shutdown - kernel_task running hot.
Hi,
I was playing Braid on supremely low battery, and my MacBook Pro 13" (Early 2011) running 10.7.2, automatically turned off. Plugged it into the charger and went to bed. Booted it up next morning and it is so incredibally slow. No warning, no gradual slow down, just all of a sudden. No peripherals attached at all.
Checked my Activity Monitor, kernal_task is running at 330mbs, from what I've seen that is pretty bad. That's the only thing I can see that is out of the ordinary.
Anyone want to take a stab at the cause of this sudden slow down? It's making using my laptop very very tedious.Note: In Safe Mode kernal_task is running at 220mbs. Is that a clue? I don't know.
Maybe you are looking for
-
How to integrate the XML data received via email in to MySQL
Hi, This is JK, my compnay is planning to adopt Adobe Livecycle Barcoded forms technology, We are planning to automate the Weekly report submission of the HR dept of my company, where the various employees from various branches will be submiting thei
-
CS4 Adobe Extension Manager not working after Mavericks
Hello, I upgraded to Mavericks and now my watermark is no longer appearing in the Extension drop down menu. I tried to reload it but when I open Adobe Extension Manager in CS4 and try to upload it I get the following message "You do not have the app
-
Where can I find the Oracle Home Directory
hi, When i try to setup SALT g10R3, I will have to specifiy the oracle home directory. I have a global variable $ORACLE_HOME which contains this path : /produits/oracle/product/10.2.0 ! I try to validate but this message appears : ===================
-
Anonymous ftp does not list directory - Solaris 9
I've got 2 Solaris 9 systems set up for anonymous ftp access. One will show a directory listing, the other won't. AFAIK, I set them up the same, and the ftpd binaries have the same checksum. Anyone know how to permit the directory listing? By directo
-
WM : Automatic TO from TR at GR from PP - Steps
Hi, Thanks in advance, I want to create Transfer Order automatically, as soon as Goods receipt against Process Order is created ( MB31 - 101 against order). TR is created and I am able to convert it manually to TO. Please let me know config steps for