Windows, RAC and network card problems... ?

Dear friends,
I've a problem! :)
Here are some info:
Node Hardware:
     Processor: Intel(R) Xeon(R) CPU E7430 @2.13GHz (2 processors)
     Installed memory(RAM): 52.0 GB
     System type: 64-bit OS
     Windows edition: Windows server 2008 R2 Enterprise
Network cards (Shown by WIN):
     PublicLAN: HP NC373i Multifunction Gigabit Server Adapter
     PrivateLAN: HP NC373T PCle Multifunction Gig Server Adapter
     Offline: HP NC373T PCIe Multifunction Gig Server Adapter
Software:
     Windows 2008 R2 Enterprise (Very last updates from MS)
     Oracle RAC 11.2.0.2.0 (Clusterware, DB) – 2 nodes
Environment:
     AD network. Everything is MS based.
Problem description:
During RAC installation, company had only one network card (server network card, per node). Installation was successfully finished. RAC was/is in production. Has some problems, but noting for alarm.
This days, we get other network cards. (purpose: network redundancy).
RAC shutdown was clean.
Network card inserted to nodes by OS Admin.
Nodes was started up... and...
OS Admin disabled network card immediately after logon screen was available... but to late...
Windows changed network card order!!! PublicLAN was not at the first place when Cluster started (Network and sharing center -> change adapter settings -> Advanced (from menu) -> Advanced Settings -> Adapters and Bindings)!!! (I found in logs that MAC address changed at this point!)
Cluster started hardware reconfiguration... and... we could not stop CW till starting up finished... ! After stopping CW again, we set PublicLan at first place, and every win setting was as at the moment of installation.
Cluster was started again, DB, OEM too...
Everything is working. Client can connect to DB, applications work well... but...
Damage is done... now we have totally new IP situation inside... changes are saved to the DNS, too!!!
Before inserting network card IP settings (nslookup from any client) :
rac1 192.168.217.60
rac1-vip 192.168.217.62
rac2 192.168.217.61
rac2-vip 192.168.217.63
rac-scan 192.168.217.64
192.168.217.65
192.168.217.66
After this incident (nslookup from any client):
rac1 192.168.217.60
192.168.217.62
192.168.217.64
192.168.217.66
rac2 192.168.217.61
192.168.217.63
192.168.217.65
192.168.217.66
VIP and SCAN IP address are the same as before...
nslookup show as that rac1,rac2,rac-scan change IP addresses in round-robin scenario!!!
We stopped RAC couple of time and OS Admin cleared DNS records (both zone)... but every start of cluster make changes again in DNS.
Other "side-effects":
Some cluster commands, invoked from CMD, fire errors (lsnodes, cluvfy comp nodecon -n rac1,rac2).
Configuration files seem to be correct (listeners, scan, scan_listeners, etc). srvctl and crsctl command are working without errors. oifcfg too.
Logs are full of errors (like: ASM could not be reached... no listener)
Listener(s) stop working sometime...
Relocation of resource are not possible.
Well, I mentioned the most important things... other alerts and errors in logs are present, but everything is connected with this issue, I think...
As I said: RAC working. Clusterware, DB, OEM, connections, applications, backup... everything look good... but we have a problem!!!
Any ideas, any suggestion, any link, any advice, anything are welcome!
Thanks!
PS.
Metalink haven't any document about this... I've found a lot of examples for changing IP's, interfaces, interconnection... but noting about fixing problem!

I'm having the same issue. My desktop pc keeps dropping the connection to my network (airport extreme router) while the rest of my devices (macbook pro, xbox, mac mini) still stay connected. The pc never had this issue prior to installing Windows 7 so im guessing there must be something with the Windows 7 OS.

Similar Messages

VIA KT400 Network Card Problems!

I've read allot about the problems I've been having and done many searches on Google and it all seems to come down to this: ALL VIA Motherboards in the KT400 series(and many other chipsets) lock up when using ANY Wireless Card\Usb Adapter. The frusterating part is nobody seems to have a clear answer on how to fix this or if it's even fixable
The forum linked down below tries to claim this only happens with Linksys cards.. This is false as I have a Microsoft Wireless G USB adapter and the EXACT SAME thing happens to me.
The strange part is if you are just browsing the web and reading text, everything works 100% fine. But as soon as you do something that uses DirectX or 3D Acceleration, like say Streaming Videos.. it freezes with the mouse curser just sitting there and I must hard reset the system.
Does anyone out there know of ANY kind of fix? I'm dying to know.
You can view someone elses post referring to the exact problem I have in the VIA Arena Forum
AMD Athlon XP 2500+ @ 2.00 Ghz
512 MB Ram
GeForceMX 5900XT
Antec 420 Watt Power Supply
Windows XP SP2
Latest VIA Hyperion Drivers

Hey guys it's me again.. Well the computer now seems to freeze less than it did before, but it still freezes.
After all this going back and forth and troubleshooting hassle ive decided it has to unfortunatlely be a hardware problem. I've stated before that it only freezed when running a 3d app and network card running.. but now it freezes even when I'm just on the web. It's just so totally random, sometimes it will freeze twice in one minute and sometimes it won't freeze for almost a whole day.
I've narrowed it down to 3 things: Bad HD, Bad Processor, and worst of all Bad Motherboard. Another possibility, does a the lithium battery on the motherboard ever cause problems if it's almost dead?(Assuming it's the CMOS battery?) And could that cause problems?
I had an episode before that I didn't tell you guys before. This was still after i had the network card, but probably unrelated. The computer once or twice made a very strange electrical zapping noise or screetching noise before and the whole system would almost fail and then try to resume again, and then just shut down.
After this event happened I figured it was the PSU not putting out enough power as I had installed new hardware lately. I bought a new 430W psu and while I haven't had the strange problem I had before, I still get random lockups.
I'm pretty sure it is the harddive, because it would make sense since I heard this noise before and the fact that it just freezes could just be the HD getting stuck and not spinning anymore.
It's funny because I had just replaced a faulty harddrive before in one of my older computers. However that one was much more obvious as it would constantly have to repair files in sectors. The HD I have now never comes up with errors, but maybe It is running fine before it decides to lockup.
Yet another thing it could be is the processor maybe just not generating enough juice to keep the processes going or something.
I did have problems with freezing before the network adapter now that I think back, but they were far and few between and now the problems are more pronounced. I'm going to hope it just the HD, if not it's really going to suck to already have to buy another motherboard or processor. I just built the system from scratch last year.
Sigh, Oh well. Glad for anymore insight on this issue and your opinions on what is most likely the problem. I'm going to go looking for a HD in the mean time.

T400s and Windows 2008 Server - Network card

I have installed Windows 2008 Server Enterprise edition on T400s. I cannot get network card to work, or wirless. I tried drivers for Win 7 and Vista. Are there any drivers for 2008 Server, or workaround?

Partially solved the problem for wirlesss connectivity:
1. Downloaded drivers from Intel site for Intel Wireless 5300 card
2. Enabled wireless setting on Win 2008 through features option

Problem with sound and network card

when my mainboard broke down i received other mainboard - 845PE Max - but i didn't get drives to it. Sometimes sound screeched but it worked fine till I reinstall windows. I had to download drives by Live Update, and after i downloaded it all sound screeched allmost every time, especially when i do something (click, close window etc.). It looks that sound work worse when processor is more busy. I tried to reinstall drives, but i didn't change anything. I have 2.1 speaker system, and it worked fine at old mainboard. I have win XP professional SP2, and it doesn't see any problem, and onboard realtek sound. Anyone know what can be a reason??

I did get some disturbing backround noise after updating latest audiodriver for my 865pe v.1 board (C-Media 9739A) ,from Live update.
Tried some different settings, but did not solve the problem, so I installed my
Creative SB Live 5.1 pci-card with latest drivers, instead of going back to old driver - and now I´m happy again and got better sound as well in my 2.1 speakers.
Try to find an older driver and see if problem go away ( pitty you don´t have the original MB CD drivers ) or buy a “cheap” audio pci-card, which probably will give better sound as well compared to on-board.
( you may have to disable on board sound in bios first )

Network card problem with Mobo make the computer crazy!!!

Im using a msi 745 Ultra version 10/cpu xp2400/basic graphics card/40gb HD, 256mbs of drr
I have tryed 2 networks cards both with the same results & even changed mobo & ram/graphic card/HD.
The computer seems to work fine untill i decide to put in a NIC.
It starts to post the wrong processor speed/screen decides not to display sometimes & takes a little longer to boot into windows. It will also some time crash when i turn on the computer. If i try to save something in the bios it will then reboot & then try to boot of the floppy drive.HD / CDrom drive but will not find them.This has happend on both mobos.
This is a very odd problem im getting need some help ASAP.

Sorry Bakes...folks aren't just waiting arount to help you. Expecting an answer in 2 hours is placing to high of an expectations on a user to user help forum.
No one here works for MSI, we are all users, just like you.
If you have not seen a reply, then there are several reasons that may affect why there has been no reply.
No one knows, or can offer o good answer to you question.
The question is too general and you did not supply the necessary information someone might need to even begin helping you. I have provided the basics on what we need at the top of this forum.
No one may be familiar with your motherboard's chipset, perhaps someone is but they have not visited the forum lately.
I can give only some general tips to consider for the time being.
Some incompatabilities may exist with a certain NIC card.
Check PCI slot IRQ sharing conflicts. Typically I stay to the middle slots and avoid the first and last. You may have to power down, move the card to another slot, and power back up. Each time checking your IRQ's in either Device Manager or System Information to see that the card is on its own IRQ.
Improper BIOS settings can cause conflicts.
Try "Plug and Play Aware OS" set to "No" and let the BIOS manage things or set it to yes and let Windows do it. In most cases it has been recommended to be set to no.
Upon installation of new hardware the setting "Reset Configuration Data" can be useful in avoiding lockups after POST due to conflicts recognized during "Verifying DMI Pool Data"
Possible reasons: Hardware change, BIOS settings change, improper connection of IDE cables, corrupt MBR (Master Boot Record) of the HDD (Hard Disk Drive), defective HDD or defective mainboard.
Possible causes: Hardware incompatibility, virus attack, electric circuitry damage/defect, corruption of data, improper BIOS settings, over-clocking damage.
*NOTE* Some Chipsets do not support this feature, see manufacturers documentation.
That's about all I care to share for now.
Good luck........

Windows 7 and iTunes 9 - problem connecting to Airtunes to stream music

I have a new laptop with Windows 7 and iTunes 9. iTunes recognizes my Airport Express (AE green light lit, and shows up in lower right of iTunes when choosing which speakers to play), but I cannot connect - just hangs on "Connecting to User's Wireless Music Airport Express" (name of the Airport Express network added to my existing Wireless network). No error message. Thus, unable to listen to my music through my hi-fi stereo. It's killing me!
Tried a few things: disabling firewall, unplugging, resetting AND reconfiguring the AE, no luck.
Anyone else having this problem? Any suggestions? Thanks

Figured it out - just needed to add iTunes to 'trusted applications' in Kaspersky Antivirus/Firewall..
Simply launch Kaspersky > Settings > Threats and exclusions > Exclusions Settings > Trusted applications > Add > "C:\Program Files\iTunes\iTunes.exe > select all exclusions > OK.
Also added Airfoil and now able to stream Pandora through my stereo!

A question about Routers and network cards

I have a question, Can Hardware confict with internet speed problems with the routers like one having a gigabit etherenet network card and 1/100 intel etherent card?

Ethernet components are generally compatible across brand names, and speeds. So you can connect gigabit cards to 10/100 networks. You can connect 10/100 cards to gigabit networks.
When you mix speeds, you will be limited to the fastest speed that all components can do, so if you connect a gigabit card to a 10/100 network, you will be limited to a 100 Mbps connection.

Windows 7 and Networks with High Latency

We are currently trying to rollout Windows 7 on our network to replace XP but have encountered an issue whereby we have remote clients that access the network over high-latency satallite links (BGAN and Vocality/Satellite). The latency of the links (based
on ping results) can be 600ms for Vocality and 1-3s for BGANs.
The particular services that don't work are a full motion video solution using TVI Viewer 7.9.1 and Outlook 2003 or 2007. These work fine on Windows XP. Shares can be accessed but are significantly slower than XP and ping does respond fine.
Windows 7 is running on Panasonic Toughbook CF52 and CF74 and I've tested in with a vanilla install with no updates and not on the Domain (2008R2 native) to eliminate GPO interference and tried it with all MS updates as of about 2 months ago.
I've tried removing the extra services on the network card (Topology Discovery, ipv6 and QoS), updated to the latest NIC drivers from Panasonic and drivers from Intel themselves. Reduced the MTU to as low as 500 and increased the Frame size (I forget what
to but was following a guide for slow links).
I've successfully replicated the issue on out development system using a satallite simulator.
Windows 7 with Outlook and TVI work fine on our network when connected via the LAN, ADSL, 3G and WiFi.
I'm currently analysing Wireshark captures but they don't seem any different to the XP ones.
Any help would be much appreciated.

Hi,
I noticed that your issue just happened when you use satellite transmission connection.
The fact is that this kind of connection in Windows 7 use TCP protocol. Transmission Control Protocol ( TCP ) under ideal conditions can provide reliable data delivery, but it is inherent in the existence of a throughput bottleneck, with the emergence on
the long-distance WAN packet loss and latency increases, the bottleneck is becoming more prominent and serious. In satellite networks with high loss, effective throughput may be as low as 0.1% - 10% of available bandwidth.
However, FASP can be the solution.
FASP
http://asperasoft.com/technology/transport/fasp/#overview-464
This response contains a reference to a third party World Wide Web site. Microsoft is providing this information as a convenience to you. Microsoft does not control these sites and has not tested any software or information found on these sites; therefore,
Microsoft cannot make any representations regarding the quality, safety, or suitability of any software or information found there. There are inherent dangers in the use of any software found on the Internet, and Microsoft cautions you to make sure that you
completely understand the risk before retrieving any software from the Internet.
Thanks for your understanding.

945 PL Audio and Network intermittent problems...

Hello,
Hopefully someone can help me here. I recently built a comp for a friend with a 945PL Mobo and a dual-core 2.66 Ghz processor. Everything is fine, except that the audio sometimes works, and sometimes doesn't. This includes when I disable the onboard audio and switch to a 3rd party card. Also, I have hooked the comp up to my network in order to update windows, and everything worked fine, except for the fact that with each restart, I had to unplug the network cable and plug it back in.
I have reinstalled both the audio drivers and the drivers for the network card, as well as disabling/uninstalling the components and then reinstalling them.
Currently, the audio is working again(had ONE instance where it wasn't working, and I went to log out, and it started working again...). Usually, it will work for a minute or two, and then stop, with NO errors.
Unfortunately, the network card just keeps trying to establish a connection, so I can't get the comp online to update anything.
I have also tried flashing the BIOS, except that I can't get it to work for some reason. I followed the instructions provided here, but the BIOS utility doesn't seem to want to run. Maybe I'm missing something.
If anyone has ANY idea what might be going on, it would be GREATLY appreciated!!
This is driving me nuts, and also making me look like a moron to the friend I built the computer for.
Thanks!!
Mike Wells

"What's your full system build? Please list out."
Sorry for the slow reply, I've been seriously busy...
System:
945 PL Mobo
2.66 Ghz Dual Core P4 Processor
1 Gb Crucial DRAM
Radeon X550 PCI Express Video Card with 256 Mb RAM
Maxtor 250 Gb SATA HDD
Sony DVD-ROM
Pioneer DVD Burner
Cooler Master Case
Thermaltake Typhoon cooler
Audio and Ethernet are both built in.
I have updated the audio, the ethernet and the INTEL drivers, still no luck. The network card continues to try and get on the network(Funny thing, I can access my router, but even if I hook straight up to the cable modem, it never accquires an address.). The audio worked MOST of the weekend, but it still stopped working on two occasions. I left in on for hours at a time, I restarted a million times, I even played full CD's to see if there was any pattern to the audio issue, nothing seemed to show up, except that it doesn't go out while playing something...
Hope this helps.
Does anyone think that this could be a Windows issue, even though putting in another souond card didn't help? I haven't installed so much software at this point that a re-install would be too much of a pain in the butt...
Once again, thanks for helping.

WRT54G Extremely slow navigating pages @ 192.168.1.1 - Could this be a network card problem?

Friend of mine is having Internet connection issues on his main PC which is hard wired to the router, He's using Comcast cable (18Mbit) and all of a sudden today the speed dropped to dialup speeds, literally, however its ONLY this main pc with the speed issue, there are 2 other computers connected wireless to the router and they are running full speed when testing on speedtest.net
While troubleshooting the problem I tried bypassing the router and the speed issue still remains, So I can pretty much rule out the router, But as part of my troubleshooting whenever I try to access the router's configuration pages via 192.168.1.1 it is VERY slow at responding.
For example when hitting enter after typing 192.168.1.1 it takes around 45 seconds to display the router configuration page, and at that point clicking on any other tabs takes 30 - 45 seconds as well to respond.
So my main question with this post is, is it possible his network card went bad? What would cause really slow access to the router configuration?
The PC is running Win 7 Ultimate 32bit and Ive tried running the network troubleshooter, uninstalled his network card in device manager / reinstalled the drivers but nothing seems to be working.
I also ran Malware Bytes and scan results were clean.
Any ideas appreciated!
Solved!
Go to Solution.

can you "borrow" a card? its the only way to be sure, eliminating hours of trial and error procedures. one of the mega electronics stores is a good source, if it solves your problem you keep the card, if not there is the return option
ps. i am not a tech, i just play one on tv!
pps. free speech is a human right! join Reporters Without Borders (http://en.rsf.org/) and help save the planet from censorship predators!

Integrated Network card problem with K7N2 Delta-L

my integrated network card doesn't recognize any RJ45 cable bluged to it !!!
"ofcourse i enabled it from Bios"
the card is identefied by windows normally as nVidia ethernet ......
i tried to change the version of nForce driver but no way.
i pluged a normal PCI network card and work well with the LAN ... unpluged & re connect the integrated one with same cable but no way .. the task bar icon told me that A CABLE IS UNPLUGED >>
plz help

hi
what do you tru to connect it to?
i cant use onboard lan with my cable modem but a friends router worked without trouble.
btw welcome to this forum
bye

Y500 dual boot windows 8 and fedora 19 problem

I bought a y500 two days ago and i wanted to dual boot windows 8 and fedora 19, so here's what i did
1. downloaded fedora 19 (x64) iso from the fedora website.
2.made a live USB using live usb creator.
4.opened disk management utility and shrunk the c drive (windows 8 was installed here) by 100 gb and kept the 100gb unallocated.
3. started the laptop with novo button, changed the bios config to boot from usb.
4.installed fedora from usb, selecting the 100gb unallocated memory for installation
5.restarted the laptop.
now the problem is fedora works perfectly but when i try to boot windows 8, the following error is shown.
windows failed to start
file:\BOOT\BCD
status: 0xc0000225
info:the boot configuration data for your PC is missing or contains errors.
i am guessing the fedora installation overwrote the boot files of windows and
i have not taken a backup. please help

hi,
I have a Y500 and I wanted to dualboot fedora 19 with windows 8, this proved to be unsuccessful. I had made a repair disk before the process (but not a set of recovery disks unfortunately >.< ). now I inserted the repair disk and selected the automatic repair option, it showed a message that auto recovery has failed. now when I pressed the NOVO button and selected the system recovery option, it does not go into the OKR menu but continues with the normal booting process. Can somebody guide me or give links where I can find step by step instructions to making OKR work and reset my laptop to factory settings? PLEASE help As Soon As Possible
NOTE: I did resize the windows 8 os partition but the recovery and the lenovo partition are still untouched

Dual Boot windows 32bit and 64bit overclocking problems

Im pretty new to overclocking and this is my first try I manage to get my AMD Venice 3200 to hit 2500 with 250fsb X 10, HTT 4, vcore 1.44. I used memory divider 166/200 so the memory is running at 208MHz not alot of overclocking on the memory since it is some cheap brand.
My problem is that I have dual boot and with windows xp everything is fine CPU-z reports the right speed for the cpu and memory when I overclock, and there is an increse in preformance with overclocking, But when I boot windows XP 64bit CPU-z reports the FSB as 200 so it is not showing any change, it does report the change in the memory divider 166/200 and the cpu voltage increased that I applied to overclock. The thing is that when I open systerm properties it shows the CPU speed as 2500MHz but when I test the preformance there isnt any increase. I used Superpi to test preformance and in windows XP 32bit it finishes the 1M test in 36seconds while in Windows XP 64bit it takes 42seconds.
My system specs are
AMD Venice 3200
MSI K8N Platium bios 1.8
1024MB Wintec Memory 3200
Geforce 6800 GTO 400/1100
OCZ ModStream OCZ52012U 520W Power Supply

Im runing the final release of Windows xp 64 and cpu-z 1.30, I also have Everest Ultimate Edition and it only shows 3% overclock 205 FSB. Im thinking of formating the HD with windows 64 and installing it again with the systerm already overclock.

Windows 8 and NACAgentToastApp.exe problem

Saludos foro
Tengo una aplicación NAC fuera de banda version 4.9.3 funcionando correctamente con clientes Windows 8 y clientes windows 7. La version de agente NAC es 4.9.3.5, el problema que tengo es con todos los clientes Window 8 y el ejecutable NACAgentToastApp.exe
Tengo los siguiente errores en el visor de eventos.
Greetings forum
I have an application NAC OOB version 4.9.3 working properly with Windows 8 client and Windows 7 clients. The NAC Agent version is 4.9.3.5, the problem I have is with all customers Window 8 and the executable NACAgentToastApp.exe
I have the following errors in the event viewer.
Nombre de la aplicación con errores: NACAgentToastApp.exe, versión: 0.0.0.0, marca de tiempo: 0x506a06aa
Nombre del módulo con errores: NACAgentToastApp.exe, versión: 0.0.0.0, marca de tiempo: 0x506a06aa
Código de excepción: 0xc0000409
Desplazamiento de errores: 0x001b0b59
Identificador del proceso con errores: 0xc98
Hora de inicio de la aplicación con errores: 0x01ceaf0058b6d2f1
Ruta de acceso de la aplicación con errores: C:\Program Files (x86)\Cisco\Cisco NAC Agent\NACAgentToastApp.exe
Ruta de acceso del módulo con errores: C:\Program Files (x86)\Cisco\Cisco NAC Agent\NACAgentToastApp.exe
Identificador del informe: 9667b97e-1af3-11e3-be98-80c16ef6536e
Nombre completo del paquete con errores:
Identificador de aplicación relativa del paquete con errores:
Greetings forum
I have an application NAC OOB version 4.9.3 working properly with Windows 8 client and Windows 7 clients. The NAC Agent version is 4.9.3.5, the problem I have is with all customers Window 8 and the executable NACAgentToastApp.exe
I have the following errors in the event viewer.
Nombre de la aplicación con errores: NACAgentToastApp.exe, versión: 0.0.0.0, marca de tiempo: 0x506a06aa
Nombre del módulo con errores: NACAgentToastApp.exe, versión: 0.0.0.0, marca de tiempo: 0x506a06aa
Código de excepción: 0xc0000409
Desplazamiento de errores: 0x001b0b59
Identificador del proceso con errores: 0xc98
Hora de inicio de la aplicación con errores: 0x01ceaf0058b6d2f1
Ruta de acceso de la aplicación con errores: C:\Program Files (x86)\Cisco\Cisco NAC Agent\NACAgentToastApp.exe
Ruta de acceso del módulo con errores: C:\Program Files (x86)\Cisco\Cisco NAC Agent\NACAgentToastApp.exe
Identificador del informe: 9667b97e-1af3-11e3-be98-80c16ef6536e
Nombre completo del paquete con errores:
Identificador de aplicación relativa del paquete con errores:
¿Que puedo hacer para mitigar este error?
What I can do to mitigate this error?

•1.     Verify that UAC (User Account Control) is enabled.
•2.     Verify that Internet Explorer is running in Administrator mode.
•3.     Verify if some active X fucnction fails and try to reset all the IE and active X permissions to default.
•4.     Verify if any other Anti Virus (AV) software prevents IE from launching its executable from its temporary directory.

SAP EP - Windows 7 and IE 8 problem

Hi all,
Sorry to disturb all of you.
I'm confronting a ridiculous problem.
Some of my clients are using Windows 7 and IE8. The EP is working fine.
However, there is somewhat of PCs don't work with Windows 7 and IE8 the browse will hang and became idlely.
Then I had tried to open EP in Firefox but It worked like a charm.
May I know is there any solution to resolve my problem.
Thank you very much.

Hi,
I just got the same question. Below I capture the reply from OSS for your reference.
I have checked the SP level for your system which is SP12, I would like you to check attached PAM for NW7.0,
if you would like to use Windows7 and IE 8.0, the SP level could be not lower than SP21,
more detail please refer to attached the PAM file page 16 and page 17.
The PAM could be found in above reply. :P
PS: the compatibility mode of IE8 could not fix all the problem which happen when using the Portal.
cheers,
Gary

Windows, RAC and network card problems... ?

Similar Messages

Maybe you are looking for