Wireless network works fine but Ethernet connection does not

Airport Extreme base station connected to DSL line connects perfectly with remote Macs. However, the hardwired Ethernet connection to my G4 is not recognized. When I connect the DSL modem to the G4 using an Ethernet cable, it works perfectly. Genius at the Apple store replaced my AP Extreme base station to no avail. Can anyone suggest what I should check for?

I have seen this exact problem when attempting to configure his iMac through Ethernet to a D-Link Router and an iBook with Airport Extreme (wirelessly) to the D-Link. The D-Link was connected to a DSL modem. The symptoms were that the wireless connection was working perfectly, but the iMac was unable to connect through Ethernet. I worked for hours trying to eliminate every possible issue. Finally, called D-Link for support and discovered the problem. I had configured the D-Link through the iBook for connection. Consequently, with it was necessary to change the iMac connection to DHCP, otherwise the logon attempt was redundant. After a fews of frustration, the lesson was thoroughly learned.

Similar Messages

  • Back in Dec I updated Itunes, with the new version, my IPHONE now I can no longer sync to Itunes. I have an IPOD that works fine but the IPHONE does not. What can I do?

    Back in Dec I updated to the new version of Itunes. Since then, I can no longer sync my IPHONE. I have an IPOD that works fine, but the phone is not found on Itunes. I am abled to download pictures to my computer, but I can not sync my music. What can I do?

    Click here and install the software.
    (71121)

  • Airport Express wireless network works fine, but won't connect to Internet

    I had a power outage and since then my Airport Express doesn't connect to the Internet although everything else seems to work. I can see the AE just fine in the Airport Utility. My computer connects to the wireless network provided via the AE, so does my iPhone, so does my wireless printer, and I can print wirelessly from the computer to the printer, so the AE's wireless networking is working. If I directly connect my computer to the ethernet connection that I use for the AE, it connects to the Internet, so I have wired connectivity to the Internet. But somehow, I can't get to the Internet using the wireless network of the AE. Any suggestions on what I should try next?

    Hi there,
    Try to reset your Airport Express (AX), y pressing the little dot on the back of device. Keep pressed for some seconds until it flashes. Start then your Airport Utility and go through the setup process again. This will reset your whole wireless network. This may work for you. Good luck.

  • I have a Mac OS 10.6.7 that will not activate the scanner option on a C7280 HP All in One Printer, Fax, Scanner - the Printer works fine but the scanner does not - any suggestions?

    I have a Mac OS 10.6.7 that will not activate the scanner portion of an HP C7280 All in One - prints fine  - but won't activate scanner.

    I have the same problem with an HP Scanjet 8250 and my Epson Stylus NX400.  I have reloaded allegedly updated drivers.  I have researched using SANE.  Neither scanner wants to work since the  OS X10.6 update.  I have found very little out there about this problem.  
    Can anyone help me make these bricks work?  Really would like a solution that won't cost me hundreds to replace the equipment. Thanks so much.

  • HT3728 My Time Capsule is working fine with ethernet connection, but it is no longer working with wifi, probably because of my wrong setting; is there a way to reset wifi setting without losing backuped data? Thanks you all

    y Time Capsule is working fine with ethernet connection, but it is no longer working with wifi, probably because of my wrong setting; is there a way to reset wifi setting without losing backuped data? Thanks you all

    Giancarlo Messalli wrote:
    1) are you sure a reset holding the reset button will not delete my data?
    Absolutely sure.. There is no connection at all.. reset is only the router side of the TC.
    For the hard disk to be erased you need to access the airport utility disk page.. request erase and confirm the operation.
    2) I can access to time capsule by ethernet but I am not able to input the corret setting by myself
    Thank you again
    I am uncertain why if you have access you cannot change settings.. but that is why you reset things so any of those problems should be fixed.
    Here is the Apple info on reset.
    http://support.apple.com/kb/ht3728
    And here is the quote from the horse's mouth so to speak.
    Factory default reset: Perform this reset if you wish to repurpose the AirPort Base Station or Time Capsule and want to remove all personal profiles and settings first. This reset resets the device to its state when you first purchased it. Data stored on internal or external hard drives connected to the device will not be erased. If you choose, you may manually erase the hard drive using AirPort Utility.

  • I have purchased new iphone 3gs, its usb cable and charger not working.When I plugged in usb cable to my laptop it says"usb power hub exceeded". When I use another cable I have, it works fine.But the original one not working.Any help?

    I have purchased new iphone 3gs, its usb cable and charger not working.When I plugged in usb cable to my laptop it says"usb power hub exceeded". When I use another cable I have, it works fine.But the original one not working.Any help?

    Are you connecting your iPhone directly to your PC or to a USB hub?

  • HT4641 Im trying to print off my cv, page 1 prints off fine but page 2 does not, I'm using the selected template for curriculum vitae why does my page 2 not print?

    Im trying to print off my cv, page 1 prints off fine but page 2 does not, I'm using the selected template for curriculum vitae why does my page 2 not print?

    Hi @kots 
    I suspect your question would be better answered in the HP Enterprise Business Community, as your HP Printer is a commercial model.
    My technical expertise is with consumer products and software, I am sure the commercial folks would be happy to help if you re-post your question for them to answer. The HP Enterprise Business Community is an HP Forum designed for the Commercial and Enterprise customers to help one another. I am sure you will find some HP folks there to help too.
    Click here to view the Printing and Digital Imaging. When the page opens you will see the option to 'Log in' or 'Register Now' on the right. The commercial forums are separate from the consumer boards, thus you will need to register if you don't already have a commercial account.
    You may find the HP LaserJet M2727 Multifunction Printer series page helpful while you wait for somebody in the commercial Forum to respond to your inquiry.
    Best of luck.
    Please click the Thumbs up icon below to thank me for responding.
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Sunshyn2005 - I work on behalf of HP

  • HP Pavilion Entertainment PC: WiFi works, however, hard wired connection does not work.

    Internet via WiFi works, however, hard wired connection does not work.
    My software indicates my hardware is working properly.
    However, if I connect another computer to the cable I am using, it connects to the internet without a problem.
    And, if I connect my comupter to another cable that works with another computer, my computer still does not connect to the internet.
    HP Pavilion dv9700 Notebook PC
    32-bit Operating System
    Windows Vista Home Premium Service Pack 2

    It could be that the touch pad is broken on the inside and the contact area for the one button is either broken, blocked with an object or the cable going to the mother board is not inserted correctly into the mother board connector. I think in any case the case will have to come off and someone look for physical/connection problems.  It doesn't sound like a software problem but there is always a chance.
    Reminder: Please select the "Accept as Solution" button on the post that best answers your question. Also, you may click on the white star in the "Kudos" button for any helpful post to give that person a quick thanks. These feedback tools help keep our community active, so you receive better answers faster.

  • I have just recently installed ios6 to my iPad 3 an iPhone 4 my iPhone works fine but my iPad is not working at all I can not get a response from it, it seemed to download an then install but did not reset and turn on and will not turn on HELP!! Withdrawa

    I have just recently installed ios6 to my iPad 3 an iPhone 4 my iPhone works fine but my iPad is not working at all I can not get a response from it, it seemed to download an then install but did not reset and turn on and will not turn on HELP!! Withdrawal or what!! Lol

    Hi there,
    Firstly, try a hard reset. Hold the sleep/wake and home buttons together until the Apple logo appears.
    If this doesn't work, try restoring your device. Put it in recovery mode if iTunes doesn't recognise it, and restore it from there. I have linked to instructions below.
    Recovery Mode and Restore - Apple
    Let me know if this helps,
    Nathan

  • I have a pc running windows 7.  I got an Airport Extreme 802.11n Wi-Fi and the printer is now plugged into the Airport.  The wireless router works fine but the printer shows as offline in control panel and in word. The printer is a HP LaserJet CP1525nw.

    I have a pc running windows 7.  I got an Airport Extreme 802.11n Wi-Fi and the printer is now plugged into the Airport.  The Airport works fine but the printer shows as offline in control panel and in word. The printer is a HP LaserJet CP1525nw.

    +For now I have it set to Share Public IP address - Is this correct for my Network Setup with The Airport Extreme being the only router being used ?+
    This would be the correct setting if the AirPort Extreme is connected to a simple modem (one ethernet port).
    *Settings I have Enabled*
    5 GHz name indicates that you have elected to use the option to assign a separate name to the 5 GHz network. This will allow you to "tell" compatible computers to connect to that network, rather than the slower 2.4 GHz network
    Use Wide Channels is recommended for 5 GHz operation.
    Interference Robustness often does more harm than good and should not be used unless you know you are in a area with a lot of wireless networks and you feel that your network is experiencing interference issues from a nearby network.

  • I changed my appleID, it worked fine but now I can not restore icloud backup in a new ipad (old appleid does not work and it is grey colored so I'm unable to change it)

    Some months ago I changed my email address and so my appleID. Everything worked fine, but last week my ipad broke and when I tried to restore my icloud backup in my new ipad it does not work: it asks me for the password of the OLD appleID (it doesnt work); and in icloud configuration page the field for appleid is colored grey so I can not change it.
    any clues? thank you in advance

    My suggestion is to change apple id back. I know it is not something you want to hear, but there are suppose to be ways around it and usually they work, but not right now. I suspect that is consequences of Apple getting their servers ready for ios7. Normally in your situation - you should be able to get all your stuff back, but apps, and then you can sync those or download from icloud. But lately (last week) it does not seem to work normal way.

  • HPM1212nf MFP i can't scan but wireless network works fine for printing

    i have the MFP set up fine for printing over a wireless network.  Any idea on what more i  need to do to get the machine to accept a scan command from the computer using HP Laserjet Scan?

    Hi there @bc123!
    Thanks for contacting the HP Forums!
    I see that your having a communication issue with the HP LaserJet when it comes to scanning to the computer, and I would be happy to provide you with my assistance.
    A good place to start when troubleshooting scanning is to ensure the CD was installed correctly on your computer. If the CD is unavailable then I can provide you with a link to the HP driver download: Drivers & Downloads
    In the link provided you will want to:
    1.enter your printers model number and click GO
    2.select your printer model
    3.select your operating system and click NEXT
    4.Click on Driver - Product Installation Software (‏1)
    5.Click DOWNLOAD next to the full feature software
    To provide you with a more direct link to your software and to better assist you, would you please provide me with the following information:
    1. What operating system version the computer is running (ex. Mac, Windows, etc.).
    Bellow are 2 links I located from HP and Macintosh on how to locate your version of operating system.
    Which Windows operating system am I running?
    Finding the OS X version and build information on your Mac
    2. If the computer is running Windows I will need to know what version (ex. 32-bit or 64-bit). 
    I have provided another link from the HP web site showing you how to check if its 32-bit or 64-bit
    Is the Windows Version on My Computer 32-bit or 64-bit?
    3. Laserjet model number (ex. P1102w, CP1025, etc.).
    Please post back with the requested information, as well as the results of your troubleshooting.
    Let me know if this was helpful!
    Cbert
    I work on behalf of HP.
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" at the bottom of this post to say “Thanks” for helping!

  • Network works fine but Airport Utility can't see the Airport

    If someone knows of an earlier discussion on this I'd be grateful for a pointer. My Airport Extreme network has been working fine, syncing with Apple TV, accessing the Internet, etc, but The AirPort Utility can't find it! I discovered this when I had trouble printing and started up the Utility to see if there was something I could do to fix it. The utility can't find it but the network is working fine. However I do need to connect a printer to it.
    Any advise on what I can do?

    iFelix wrote:
    I know this may sound obvious and silly, but are you actually connected to your Airport wireless network and not a neighbouring network?
    I thought of that myself and there are at least four networks around my house (three unprotected!) but no, I am connected to the AirPort network!
    I'll try one other thing before I do a hard reset though. A week or two back I'd tried to connect an Airport Express manually by creating a WDS. Never got that to work and that may be a problem. I notice that if I do a soft reset the AirPort Extreme become visible in the Utility for a few minutes. I'll go th manual setup and see if I can't delete that WDS...

  • Communication Error with wireless router, Works fine with Ethernet cable.

    Video iChat is fine when my MBP and other MB's and MBP's are at my house using the Netgear 240 rangemax wireless router. I'm currently running High speed Internet via cable modem through Time Warner Cable. When I try to chat with them while they are at home, I get a communication error. I then tried to use the Ethernet cable hooked up to the cable modem to my MacBook Pro. It worked fine. I would like to use video iChat via my wireless router. I don't understand why it is not working. I think it is my router. Do I need to buy an Airport Extreme Base Station or can I still use this router. Can you possibly help me configure this Netgear router? The internet connection is fine when I use the wireless router.
    MBP 15" C2D 2.33   Mac OS X (10.4.8)   Cable Modem, Netgear RangeMax 240 WPNT834 wireless router

    I have not had very good experiences with the Netgear routers. I can't say that it is the router causing your problem, however, it might be the effective wireless bandwidth over your router. Do a speedcheck and determine the download and upload speed with wireless. Hopefully you're getting about 400Kbps up and 400Kbps down or about 1000Kbps in total.

  • JCo v3 standalone program works fine but creates connection errors RC 223

    I'm using JCO v3 with my own written DestinationDataProvider.
    In the syslog I find
    R49 communication error, CPIC return code 020, SAP rc 223
    How can I force a proper disconnect at the end of the program? I call Envirnment.unregisterDestinationDataProvider() but that does not help. In JCo v2 I used JCO.Client.disconnect() and it works. This is described in the JCo Connectivity FAQ but there is no hint for Jco v3. I can not find the equivalent in JCo v3. What are the steps to close all connections properly?

    set property DestinationDataProvider.JCO_POOL_CAPACITY as 0. This should close the connection immediately after call completion.
    Regards,
    Anurag Mahendru

Maybe you are looking for

  • FTP Adapter and FileMask

    Hi, Can anyone tell me what is allowed in the FileMask property of the FTP Adapter? Ideally, I'd like to use regular expressions. I have this filename: R060620N I've confirmed that R*N and R??????N does work But what if I want to make it more generic

  • Error after deploying JHeadstart application 10.1.3 to OracleAS 10.1.2

    Hello JHeadstart Team, I'm using jdev 10.1.3 (SU5) and jhs 10.1.3 (SU1). My application runs well in the embedded OC4J. To deploy it to my external application server I did the steps written in the article "How to deploy a JDev 10.1.3 application to

  • Is it possible to change javascript popup colour?

    in the current version, when a alert/confirmation dialog opens with background grays, the default color of the popup is half white(top) and half light-gray(bottom) . Is it possible to make it to one color( by any coding changes (or) settings in Firef

  • Round Corners in Bars of Column Chart

    i m trying to build a column chart with rounded corner bars....like we can make a text box with rounded corners using cornerRadius property...... also is there any way to show a mirror image(not a shadow) at the bottom of the vertical-rounded-corner-

  • SAP PDK Eclipse plugin : for Eclipse 3.0.1

    hi friends, I want to develop content using PDK-eclipse plugin.When I start eclipse, it do not use the plugin I put there. I put the following plugins in eclipse/plugins directory: (PATH[relative to ep installation]=./cluster/server/services/servlet_