Wireless voice quality issues with wlc 5508 7.0.98

Hi,
  I am having random occurances of voice drops (one-way audio) during phone calls. WLC 5508 (7.0.98) , LAP1242AG (only G antenna present), and 7925G phones. coverage is excellent throughout the floor and its a confined office space. Its not happening always. I am seeing these logs , not sure if it is related. :
*apfReceiveTask: Feb 10 11:31:53.831: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg
*apfReceiveTask: Feb 10 11:31:33.356: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg
I have set DCA list to1,6 and 11. I tried disabling RRM and statically fixing the channels and power also. Still the issue is seen,
7925G firmware is 1.4.1
i tried to do linktest from the WLC to the phone, but link test is failed. linktest to a laptop works though. I have only mac filtering for the voice ssid.
any suggestions pls ?
regards
Joe

Hi Serge,
Thanks for the suggestions. I have taken care of all the settings. Problem is , the user is seated in his office cabin and using the 7925 and there is around 50db signal strength in his room from an AP which is just outside the cabin. And this doesnt occur often, when we go to check and make calls, everything is fine whereas the user says it happens sometimes in the morning, evening etc... randomly... where the fone goes blank while in a call.... since the problem never happens when we go to troubleshoot the issue, we really dont know what is going on. This is happening when calling PSTN.
AP's are not restarting and there is no logs indicating that. Wireless infrastructure looks very much OK cos there are other users who are not experiencing this problem and there is ample coverage all over the floor. I am baffled why only one user has this problem even when he is seated in his office cabin.
Tried changing phones also, but still remains.
Question  : i tried to do a linktest from WLC to his phone, but it failed, while linktest to laptops are working fine. Does wlc linktest not working for wireless phones ?
regards
Joe

Similar Messages

  • 7925 Phones voice quality issues with wlc 5508 version 7.6

    Hi all,
    I have a mix environment with 1 WLC 5508  and more or less 6 sites with several Access Points ( all AIR-LAP1242AG and all in FlexConnect mode  Hreap ) and several wireless phones (all  CP7925G) . My Ap's have antennas 2.4GHz in all sites except 1 site ( the one i'm talking for now) with 2.4GHz and 5GHz , because of the problems we suggest to have all phone in A BAND (5Ghz) . In this site we force the phones just to A (802.11a only) , power safe NONE , Continuous scan mode , i fallow all in http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/7925g/7_0/english/deployment/guide/7925dply.pdf , one thing i didn’t do it was apply QoS because I can’t apply several ios commands in that 2960 with lan lite ios.
    So I have 3 SSID for data and 2 for VOICE  ( one is common to all environment and supports 2.4 and 5Ghz , and other just to test one site , with only 5Ghz  with “[WPA2][Auth(802.1X + CCKM)][Auth(FT 802.1X)]”, because I read that problem can be phone rooming , and in FlexConnect only have fast-roaming in a CCKM or a PKM  key-management solution , but even like this the problem still exist) .
    I have another sites with phones in 2.4GHz running well and others with problems.
    i read here in forums lots and lots of people with similar problems , i tried several solutions ( WLC  upgrades versions  and phones firmware's , ….  ) tried all my best of solving the problems mas now I’m running without any ideas , i did also some site surveys and detect some interferers that why I change phones to 5Ghz , and I run also WLC Config analyser to help me , but all without good success. Some changes solve temporarily problems , but after some time , people reclaim about problems.
    I can open a TAC case but first I want be sure if did all already.
    Can someone try to help me?
    ip phone 7925G firmware : CP7925G-1.4.5SR1.3      
    CUCM 8.6.2
    WLC    5508 : 7.6.120.0
    AP : AIR-LAP1242AG-E-K9    7.6.120.0       (flexconnect)
    Best Regards

    Hi Serge,
    Thanks for the suggestions. I have taken care of all the settings. Problem is , the user is seated in his office cabin and using the 7925 and there is around 50db signal strength in his room from an AP which is just outside the cabin. And this doesnt occur often, when we go to check and make calls, everything is fine whereas the user says it happens sometimes in the morning, evening etc... randomly... where the fone goes blank while in a call.... since the problem never happens when we go to troubleshoot the issue, we really dont know what is going on. This is happening when calling PSTN.
    AP's are not restarting and there is no logs indicating that. Wireless infrastructure looks very much OK cos there are other users who are not experiencing this problem and there is ample coverage all over the floor. I am baffled why only one user has this problem even when he is seated in his office cabin.
    Tried changing phones also, but still remains.
    Question  : i tried to do a linktest from WLC to his phone, but it failed, while linktest to laptops are working fine. Does wlc linktest not working for wireless phones ?
    regards
    Joe

  • An issue with WLC 5508 and 7921 phone

    Hello all!
    I have a system with WLC 5508 and some 1242 APs. And I use a lot of 7921 phones.
    One of 7921 phones was in trouble. It loses registration, disconnect conversations...
    I installed the trial WLC and run voice diagnostics.
    I  saw some of "Potentially degraded QoS in downlink direction because of  incorrect packet classification" messages and one "Fair upstream packet  loss ratio: 1,2%, which is less than threshold 2.5%"
    As I understand all of 7921 phones in these area are affected.
    what  does it mean? I set up Platinum QoS for voice WLAN. I don't have any qos  configuration string for AP and WLC ports on switches...
    any ideas?
    thanx in advance

    Sergey:
    There is one application called "WLC Config analyzer". You save your "show run-config" from your WLC in a text file and import it by this application. it will analyze the file for you and tell you what recommendations for voice are missing so you improve them.
    When importing a config file you choose what voice clinets you are using, so you need to choose cisco 7921 to it tells you what config improvemetns is needed based on 7921 needs.
    Here is the link to download the application:
    https://supportforums.cisco.com/docs/DOC-1373
    download the latest versoin.
    BTW, how many voice/data clients are connected to one AP in that area? if I remember correctly if you are utilizing voice then the max number of clients connected to one AP should not exceed 17. If you have more than this number per AP try to minimize the number of users concurrently connected to the AP then try again.
    Hope you'll find the config analyzer useful.
    If useful please don't forget to rate.
    Amjad

  • Huge Network and Voice quality issues with Xperia T2 Ultra Dual

    Same problem here after one month.
    Voice cracking can't hear other party while having full signal strength.

    Hi @Mayur9 Go to Call settings -> General -> and disable the "Slow talk option" if it is enabled. If the issue persists, boot your device in Safe mode to check what happens: http://talk.sonymobile.com/t5/FAQ/How-to-boot-your-phone-into-safe-mode/m-p/348008#U348008 Also I suggest you to first run a backup of the device information like this: http://talk.sonymobile.com/t5/FAQ/Backup-amp-Transfer/m-p/407253#U407253 Try performing a system repair using PC Companion: http://support.sonymobile.com/gb/tools/pc-companion/ This will factory reset your phone and erase all data. You might need tocharge your device for about 1-2 hours before so the device has at least 80% battery. Make sure the device is not connected to computer or laptop and turned off (sometimes you have to press power button and volume up until the device vibrates 3 times or on some devices you have to press the small button near the SIM tray or on the back of the device). Start PC Companion and select Support zone then Update my phone/tablet then in Blue Repair my phone/tablet and follow the on screen instructions - When prompted connect your phone still switched off holding volume down or back button - This should start the repair or reformat process. If you are using Windows 8/8.1 or a 64bit operating system then adjust the settings for PC Companion and run in compatibility mode and chose Windows 7 or XP. I hope can be useful. I'm at disposal for any question. Best Regards,

  • 7921-CME Voice Quality Issue

    Hello,
    I am running into an issue at customer site which is going on for over 30 days.
    They have consistent voice quality issue with 7921 phones.Have checked their phone webpage and see that jitter value increases to 500 during issue. Sometimes I see tcpretransmissions too,
    They have QoS but that doesnt seem to help.
    I have even collected sniffer off wireless but not able to play due to wireless header.
    Have worked with TAC but they do not find any thing conclusive.Can anyone pls tell me what else can be done to analyse and fix the issue

    Is the issue with unicast RTP or with multicast (i.e. paging)?
    What AP platform and version are you using?
    1.2(1) for the 7921 was just released.
    1.2(1) Software
    http://tools.cisco.com/support/downloads/go/Model.x?mdfid=280808676&mdfLevel=Model&treeName=Voice%20and%20Unified%20Communications&modelName=Cisco%20Unified%20Wireless%20IP%20Phone%207921G&treeMdfId=278875240
    1.2(1) Release Notes
    http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/7921g/firmware/1_2_1/english/release/notes/7921_12.html
    Other than that ensure the deployment is inline with the 7921G Deployment Guide.
    http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/7921g/6_0/english/deployment/guide/7921dply.pdf

  • Quality issues with IDVD solved

    Hi All
    RE. Best looking IDVD playback.
    May this help all those stuggling with quality issues with perfect looking Qtime files encoded by IDVD coming out looking crap.
    Simply this: instead of exporting your media from your FCP timeline in H.264 - instead select Motion JPEG A. This is found under your setting options in your Qtime movie/settings export window.
    Your files will export much, much faster than Apple's default setting of H.264, you will also get very smooth playback wihtout any jaggies or nasty artifacts. Files are a larger but, hey, it just looks great.
    Let me know if this works for you - it took me ages to figure this out!
    Best regards
    PostGuy40
    Imac 2.16Ghz intel dual core   Mac OS X (10.4.8)   17"

    Good info. I'll keep this in mind next time.

  • Photo Quality Issues with Pixma MG6220

    I am frustrated.  The first photo printed from this printer was of poor quality.  It was very 'grainy' and 'noisey'.  I printed from the printer itself (put camera card into printer).  I then printed from Picasa, same problem, very poor quality.  It was then a couple of months before I attempted printing again.  I printed from PS Elements 11.  The quality was much improved but not what I expected from this printer.  I finally called tech support, after tweaking every setting I could find.  They essentially blamed my computer, wanted to reinstall the drivers and I need to buy new ink cartridges.  It's NOT my computer.  I'm curious as to why they think it's the drivers.  It very well could be bad cartridges.  The printer was purchased in December (six months ago).  I'm wondering why the photo software would make a difference.  I'm irritated that the people I spoke with seemed completely incurious as to what, exactlly, was wrong with the photos.  It would appear that no on else has had this issue.  The reviews for this printer were very good.  I can't imagine reviewing these images and stating that they are "excellent" as I have read from many reviews.  I'll be more than happy to attach scanned images for review (scanner works fine).  Thank you. 

    Hi,
    Check this for scanned images and originals for reference:
    http://flickr.com/gp/skital/Y9615F
    (you can download full-res versions there as well - it's a bit hidden if you don't know flickr)
    This was using Canon Glossy II photo paper and NOT Canon Ink. I was trying different replacement inks over the time and I had similar results.
    I'm a little bit hesitant with spending more money on this printer, esp. that I had never have this kind of quality issues with my previous Canon printer (MP600) when using non canon inks - I had color issues but never grainess.
    Well, I may try original inks again, but it breaks a deal for this printer.

  • TS2681 quality issues with I pad 3, now on my 4th in 3 weeks

    Quality issues with the new Ipad 3 , now on my 4th  in 3 weeks ,  each time marks  / scraches in the metal case are evident,  not what i expect from apple , unable to e mail direct,  

    One of two things is happening.
    1) You have had an unusual run of bad luck. So, return it and try again.
    2) With all respect, you may be so picky, you'll never be satisfied.
    Matt

  • Recurring quality issues with HP Elitebook 6930p

    Good afternoon to all forumers,
    I am trying to find out if anyone besides me have the same recurring quality issues with HP Elitebook 6930p? Although these issues have all been resolved by HP. I find it very inconvenient since this is a business notebook and these issues have cause me a lot of down time and grievances. A list of my Elite book issues.
    Warped LCD panel causing the latch not to work. (1 time)
    Dead pixels on new LCD panel replacement (1 time).
    Deteriorated touch pad rubber left button, which I don't use. (1 time)
    Keyboard not working. (2 times)
    Screw holding the top sdie switch panel came off on one corner. Reason being, the screw holder cracked (1 time).
    Reading lack cover on the LCD panel cracked on its own. I rarely use this. (1 time).
    Notebook overheating. The cooling element not working properly. (1 time).
    Defective power adapter, loose contact at adapter  (1 time). Replaced within warranty period.
    I do not know whether to term this as` unlucky' or to say that today's HP business notebook has not got the `Quality' a business notebook should have. I have used other business notebook from HP, namely 2 models from the nx series but they are not as bad as the Elitebook except for the same high operating temperature issue.
     Is there any course of action that I can take up with HP Malaysia? Any advice is greatly appreciated.
    Thank you.
    -Keith CK Loo

    Hi, Keith:
    I have a 6930p and was leery about getting one, after reading this link below from the business support forum, but I only paid $499 for it brand new. I couldn't pass up a deal like that.
    http://h30499.www3.hp.com/t5/Notebook-HP-ProBook-Compaq-Slate/6930p-Quality-Issues/m-p/1066713#M1505...
    I heard that many of the issues you and the others that posted were improved/fixed by HP later on in production. My notebook was built in December of 2010, so it was pretty much the last of the line.
    I have not experienced any problems with mine thus far, after 8 months of light use.  I have tested every component at least once. I know the latch issue was fixed on later models.
    Paul

  • Dell Wireless(DW1530, DW1540) issues with VoIP on 802.11n

    We are having issues with VoIP, using Microsoft Lync, over wireless.  We are experiencing static, jitter, dead air, and dropped words during calls.  We have a Cisco wireless infrastructure consisting of a 5508 controller and 2602 access points.  We're currently runng OS version 7.5.102.0, but the issues also occurred when running OS version 7.4.100.0.
    On the client side, we've narrowed the issues down to Dell Laptops(Latitude E6430, Latitude D640, Latitude E6420) with Dell Wireless/Broadcom(DW1530, DW1540) network adapters that are 802.11n capable.
    Latitude E6430
    OS - Windows 7
    wireless adapter - DW1540
    driver - 5.100.82.112
    Latitude D640
    OS - Windows 7
    wireless adapter - DW1530
    driver - 5.100.235.12
    Latitude E6420
    OS - Windows 8
    wireless adapter - DW1530
    driver - 6.30.58.26
    All of the drivers are the latest offered from Dell.
    If we disable high throughput (802.11n) on the access points and force the clients to connect with 802.11a or 802.11g, we don't experience any issues.
    If we use another manufacturers 802.11n USB NIC in the same hardware, we don't experience any issues.
    This seems to be a compatibility issue between Dell Wireless(Broadcom) 802.11n capable network adapters and Cisco access points.  I'm guessing this issue is with all 802.11n traffic, but we're only noticing it during Microsoft Lync voice calls. 
    Has anybody else had this type of problem and found a resolution?

    Has anybody else had this type of problem and found a resolution?
    I've seen some Intel chips that simply "misbehaves" when operating in 802.11n.  Going to the laptop manufacturer's website to download the firmware is next to useless.  Going to the NIC manufacturer's website to download the LATEST firmware is more reliable.
    There's a significant version "gap" between the firmware published with the laptop manufacturer vs the ones with the wireless NIC.
    I suggest you go to Broadcom and load the latest firmware in one or two machines just to test.

  • Cisco CAP 3702I not registered with WLC 5508.

    I Have  WLC 5508 in my network. Now i need to add another 2 no of cisco CAP 3702I in to my network. But we got the following errors
    *Mar  1 01:27:06.359: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'WLC'runn
    ing version 7.3.101.0 is rejected.
    *Mar  1 01:27:06.359: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 01:27:06.359: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process m
    essage type 2 state 2.
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 01:27:25.359: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
    LER
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'WLC'runn
    ing version 7.3.101.0 is rejected.
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process m
    essage type 2 state 2.
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Failed to handle capwap control messag
    e from controller
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap p
    acket from 10.56.200.201
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'WLC'runn
    ing version 7.3.101.0 is rejected.
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process m
    essage type 2 state 2.
    *Mar  1 01:27:06.359: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'WLC'runn
    ing version 7.3.101.0 is rejected.
    *Mar  1 01:27:06.359: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 01:27:06.359: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process m
    essage type 2 state 2.
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 01:27:25.359: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
    LER
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'WLC'runn
    ing version 7.3.101.0 is rejected.
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process m
    essage type 2 state 2.
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Failed to handle capwap control messag
    e from controller
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap p
    acket from 10.56.200.201
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'WLC'runn
    ing version 7.3.101.0 is rejected.
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process m
    essage type 2 state 2.

    Your WLC seems to be running version 7.3 which is not supported with 37xx AP platform.
    You need to run WLC with version 7.6.100.0 onwards to support these new AP's.
    For more details check the Wireless Software Compatibility Matrix.
    -Thanks
    Vinod
    **Encourage Contributors. RATE Them.**

  • 3502i keeps losing communication with WLC 5508

    Hello all,
    This problem only seems to affect one of our sites.  Every once in a while, several APs would lose link to the 5508 and get stranded.  The only way to fix the issue is either to power cycle, or better yet SSH into the APs and use the command "capwap ap controller ip address x.x.x.x", and then they'd automatically rejoin the controller.  At first, I thought network hiccups caused the APs to lose connectivity, but there's none that I could find.  I have the primary/secondary controller IPs configured in them as well.  See log below:
    [previous log entries show AP working as intended, then...]
    *Jan 18 05:29:29.632: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceeded max(CAPWAP_ECHO_REQUEST
    ., 1)
    *Jan 18 05:29:29.632: %LWAPP-3-CLIENTEVENTLOG: Switching to Standalone mode
    *Jan 18 05:29:29.645: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
    *Jan 18 05:29:29.645: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to [ommitted due to security reason]:5246
    *Jan 18 05:29:29.704: %WIDS-6-DISABLED: IDS Signature is removed and disabled.
    *Jan 18 05:29:32.797: %CLEANAIR-6-STATE: Slot 0 down
    *Jan 18 05:29:32.797: %CLEANAIR-6-STATE: Slot 1 down
    *Jan 18 05:32:35.214: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
    *Jan 18 05:32:38.278: %LWAPP-3-LWAPP_INTERFACE_GOT_IP_ADDRESS: Interface BVI1 obtained IP from DHCP...
    *Jan 18 05:32:38.278: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
    *Jan 18 05:32:38.379: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.100.1.20, mask 255.255.255.0, hostname AP020
    *Jan 18 05:32:38.379: %LWAPP-3-LWAPP_INTERFACE_GOT_IP_ADDRESS: Interface BVI1 obtained IP from DHCP...
    *Jan 18 05:32:46.215: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
    *Jan 18 05:35:41.753: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
    *Jan 18 05:35:44.817: %LWAPP-3-LWAPP_INTERFACE_GOT_IP_ADDRESS: Interface BVI1 obtained IP from DHCP...
    *Jan 18 05:35:44.817: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
    *Jan 18 05:35:44.898: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.100.1.20, mask 255.255.255.0, hostname AP020
    *Jan 18 05:35:44.898: %LWAPP-3-LWAPP_INTERFACE_GOT_IP_ADDRESS: Interface BVI1 obtained IP from DHCP...
    *Jan 18 05:35:52.753: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
    *Jan 18 05:38:48.260: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
    *Jan 18 05:38:51.324: %LWAPP-3-LWAPP_INTERFACE_GOT_IP_ADDRESS: Interface BVI1 obtained IP from DHCP...
    *Jan 18 05:38:51.324: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
    *Jan 18 05:38:51.405: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.100.1.20, mask 255.255.255.0, hostname AP020
    [These log messages keep looping endlessly]
    These APs discover the controller by using DHCP + DNS.  Any suggestion will be greatly appreciated!
    Thanks,
    Wil

    I have only had this issue a few times but what I end up doing is factory default the AP. I also end up uploading the rcv image and deleting the other images in flash. I do some beta testing so it could be that the images get corrupt, but that has been my fix. The AP joins and then downloads the firmware from the WLC again. It might not be what you want to do, but maybe if its an issue with a particular AP you can test it out.
    Sent from Cisco Technical Support iPhone App

  • Client get connected occationally with WLC 5508

    Hi ,
    I have one strange problem on wireless connection.
    I just upgraded several 1131 APs to LAP with 2 new Cisco 5508 controller deployed, and we found the clients sometime can get conneted to the 1131 AP, and connection well, sometimes cannot. during our test, one conecion is ok, next one cannot, the third one seems ok again and again.
    And we also have 2 new 1140 APs, seems no such problem,
    The version for controller is  6.0.196.0, and Client is Lenevo PC with XP.
    Any suggestion? or some troubleshooting procedure I can follow?
    Thanks!
    Roy

    Thanks!
    Seems some problem with open authentication.
    On the Client, it reported cannot get associated.
    on the WLC, while I am debug client it reports:
    *Jul 14 10:18:51.844: 00:1f:3c:c2:e9:71 Sending Assoc Response to station on BSSID c4:7d:4f:47:a5:c0 (status 12)
    *Jul 14 10:18:51.889: 00:1f:3c:c2:e9:71 Ignoring 802.11 assoc request from mobile pending deletion
    *Jul 14 10:18:51.889: 00:1f:3c:c2:e9:71 Sending Assoc Response to station on BSSID c4:7d:4f:47:a5:c0 (status 12)
    *Jul 14 10:18:51.928: 00:1f:3c:c2:e9:71 Ignoring 802.11 assoc request from mobile pending deletion
    *Jul 14 10:18:51.928: 00:1f:3c:c2:e9:71 Sending Assoc Response to station on BSSID c4:7d:4f:47:ae:b0 (status 12)
    *Jul 14 10:18:52.446: 00:1f:3c:c2:e9:71 apfMsExpireCallback (apf_ms.c:418) Expiring Mobile!
    *Jul 14 10:18:52.446: 00:1f:3c:c2:e9:71 apfMsExpireMobileStation (apf_ms.c:4427) Changing state for mobile 00:1f:3c:c2:e9:71 on AP c4:7d:4f:47:ae:b0 from Associated to Disassociated
    I am using remote radius with WLC only.
    The strange thing is, when get connected, it looks fine, but I tried disconnect manually, then connect again, it reported cannot get associated, then I try again, it can get connect again,....

  • SFP Error with WLC 5508

    all,
    I'm facing a problem to upgrade my WLC 5508 from 6.0.199.4 to 7.0.98.218
    On my WLC, I have a bad src error message about the SFP.
    With the version 6, I have the "warning" but the port is UP and Running
               STP   Admin   Physical   Physical   Link   Link
    Pr  Type   Stat   Mode     Mode      Status   Status  Trap     POE    SFPType
    1  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present
    2  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present
    3  Normal  Forw Enable  Auto       1000 Full  Up     Enable  N/A     SFP Error
    on version 7.0.98.218, the port never comes UP:
               STP   Admin   Physical   Physical   Link   Link
    Pr  Type   Stat   Mode     Mode      Status   Status  Trap     POE    SFPType
    1  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present
    2  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present
    3  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     SFP Error
    I see a bug about CSCta32912, but normally, it is solved in version 7.
    How to solve this issue?
    Thanks.
               STP   Admin   Physical   Physical   Link   Link
    Pr  Type   Stat   Mode     Mode      Status   Status  Trap     POE    SFPType
    1  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present
    2  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present
    3  Normal  Forw Enable  Auto       1000 Full  Up     Enable  N/A     SFP Error

    Are you using a Cisco SFP or a third party one?
    Sent from Cisco Technical Support iPad App

  • AP 1310 with WLC 5508

    Hi,
    I have upgraded my WLC 5508 from 7.0 to 7.4 and the AP 1310 no longer can associate to WLC.
    Seems that the AP doesn't work with WLC ver 7.4
    Except changing these APs to autonomous mode, any other alternatives?
    Besides, if we change them to autonomous mode, can Prime Infrastructure manage/monitor these APs?
    thanks.

    The 1310 last support is on v7.0.x of the WLC. See the matrix below.
    http://www.cisco.com/en/US/docs/wireless/controller/5500/tech_notes/Wireless_Software_Compatibility_Matrix.html
    Prime Infrastructure can monitor the Autonomous access point but will not do anything else than monitor. Config changes is done via the bridge/AP itself.
    Sent from Cisco Technical Support iPhone App

Maybe you are looking for