WLC 5508 + AP 3502i + ACS setup help

Hello,
I have a Cisco 5508 WLAN controller, three Cisco 3502i Access Points, and one Cisco ACS 5.2. I need to set up a simple wireless authentication system where a user is asked to enter in a username and password in a web portal before being allowed access on the wireless LAN.  The usernames and passwords are available in a CSV file and would need to be inputted into ACS.
I have read several Cisco guides including the WLC configuration guide but I am still confused.  If someone can please give me some direction on how I could set this up, I would really appreciate it.
Thanks a bunch.

Thanks for the article Scott.  I followed the article and I was able to set up the WCS to allow Web users to browse the Internet.  But the Web Auth -> Web login did not work for me.  When I go to the Internet and type in www.google.com I am sent to the Google Website directly rather than being authenticated by the system with a Web Login page.  I followed all the steps outlined in the article, which is setting up WLANs with Layer 3 Web Policy Authentication and creating a user assigned to the WLAN group but nothing worked.  Can you direct me towards the right direction as to what I am missing?
Thanks!

Similar Messages

  • Low Bandwith, WLC 5508 and LAP 1142N, please help !

    Hello Everyone
    For the Environment:
    - I have a WLC 5508 With a license up to 100 AP, at the Point there are 39 AP connected.
    - The WLC is connected with 8x 1Gbit/s, as a Trunk ==> 2 Members of 3750 Switches Stack ( 4gig and 4 gig)
    - The AP are connected to diferent 2960s with an Uplink ( 3 Gbit/s)  to the 3750 Switches
    - There are max. 12 AP on each 2960s
    - The AP are powered over Ethernet
    The AP:
    - it runs a/b/g/n and on 2,4 Ghz i schould have 300 mbit/s as for the 5 Ghz it schould also run 300mbit /s
    - the Ap has an uplink of 1 Gbit/s
    The clients:
    - have a intel Wifi link 5300 AGN Card
    To the Problem:
    - if i connect to one AP, and the Signal strength is High, i get an upload rate of max. 6-8Mbyte/s.
      and i am the only Person uploading.
      if i upload from 3 clients the same data from the same spot to the same target i get 2-3 Mbyte/s per client.
      if connect to the same target and run over ethernet cable fom the same spot, i get an upload of 70 -85 Mbyte/s.
    Question:
    - Why am i having these Bandwith problems ??

    Thanks Scott,
    I understand what you are mentioning, and i really didnt do it yet.
    I realize that the primary controller was not configured on the
    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:"Table Normal";
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-priority:99;
    mso-style-qformat:yes;
    mso-style-parent:"";
    mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
    mso-para-margin:0cm;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:10.0pt;
    font-family:"Times New Roman","serif";}
    Wireless –> All APs –> High Availability tab, and did it only to the AP that is taking this beahviour.
    Is this mandatory for a 1 controller only ?
    No mather what the manual say, after that the AP is rebooting 2 mins in 2 mins... with the same kind of messages.
    The interface on the switch is getting a few input errors and the same numbers of crc... but are so few...
    Next step ... i will change it to another one's place/pathing cable.
    Regarding the Radius messages... any ideas ?
    I'm already on 30 sec's of server timeout.
    Best Regards,
    Bruno Petrónio

  • Cisco ACS 5.1 & Cisco WLC 5508 & Cisco WCS

    I have managed to get TACACS+ working for the WLC and WCS but having trouble with Radius for management authentication and authorization.
    Anyone got and ideas or good documents on how to authenticate administrators using radius ACS 5.1 for WLC 5508 and WCS 6
    I take it that I still need to define roles?
    Many thanks.
    Jay

    You may try this with radius-ietf under shell-privelege
    For read-write privileges for the user, set the Service-Type Attribute to Administrative.
    For read-only privileges for the user, set the Service-Type Attribute to NAS-Prompt.
    Regards,
    Jatin
    Do rate helpful posts~

  • WLC 5508 and ACS server

    Hi,
    Apologies if this has been answered before. I did a search, but unable to find anythimg.
    What I would like to do is be able to have a WLC 5508 as the local RADIUS DB and authenticator, but then be able to have an ACS server in a central location as a backup and then replicate between them.
    In other words set up groups for my remote sites in the central ACS server, which then replicates only the correct group to the remote sites. This allows less adminstrative overhead, as we just update the central one.
    Is this possible and how would I configure the WLC to do this ?
    Thanks

    Hi,
    if I understood your request, you want to replicate user information between an ACS and a WLC right ?
    That's impossible.
    ACS can only replicate with other ACS running the same version. No other ways of synchronization exists.
    Regards,
    Nicolas
    ===
    Don't forget to rate answers that you find useful

  • Incompatibility issue - WLC 5508 and ACS 5.4

    Hi,
    This is my scenario:
    Cisco WLC 5508 firmware 7.4.110.20 and ACS 5.4, two WLAN eap/tls, many client  can't connect to WLAN and on ACS i receive the following error:
    Authentication failed : 11051 RADIUS packet contains invalid state attribute
    workaround:
    1 -Check the network device or AAA Client for hardware problems.
    2-known RADIUS compatibility issues.
    3-Check the network that connects the device to ACS for hardware problems
    there are some incompatibility issue between WLC and ACS ? the compatibility matrix document for wireless imposes the 7.5 firmware for WLC.
    What do you think is possibile ?

    Are there any other errors shown in the details of the failed authentication?
    We may need to look at service logs in debug mode, opening a TAC case would be the best way to go about this.
    Javier Henderson
    Cisco Systems

  • IPad & 3502i WAP wlc 5508 H-REAP

    I have a wierd situation occouring at a new remote location.
    Here is my scheme.
    At my phyiscal location =WHQ
    wlc 5508 (7.0.98.0)
    vlan 800
    ssid KWD-Guest
    open authentication
    wep 48bit key
    (ACL restricted to internet only access)
    Remote physical location = 80NY 
    2821 router (12.4ios) - routes and dhcp for the locations networks.
    3560-48 switch     - user connections and WAP connections.
    3502i WAP - H-REAP back to WHQ for management and configuration.
    Remote physical location = 1441NY
    3825 router (12.4ios) - routes and dhcp for the locations networks.
    3560-48 switch     - user connections and WAP connections.
    1131AG WAP - H-REAP back to WHQ for management and configuration.
    Here is the issue we are running into.
    At 80NY the users want to connect to the guest vlan 800 ssid KWD-Guest with iPads and smart phones (model unknown).
    They can see the ssid broadcasting. Try to connect to the ssid, input the wep key. wait, wait and time out on dhcp, giving themselves a 168.x.x.x addy
    From the router side, I can see the dhcp request on the correct vlan hitting the correct dhcp pool.
    The router hands out a valid ip address and associates it to the correct wireless devices Mac-Address
    But as I said the client times out waiting for the dhcp address.
    Now the kicker here is that the very same iPad and smart phone CAN connect to the guest ssid at 1441NY which is also hosted off the same 5508 at WHQ.
    The only difference I see is the WAP model and the network addresses I hand out at each location.
    To the best of my ability I have double checked my router/switch and controller/WAP configurations against each site to make sure there is a mirror in place.
    Any ideas?
    SR 617433573

    dmantill,
    Good morning and thank you for linking in the pdf.
    I read it and hit several of the hyperlinks included in the pdf.
    While I found the information useful and informative overall I did not really see anything that explained or covered the issue I am encountering.
    I have a SR open now and the TAC engineer wants me to capture some debugs on the client mac. Once I can get the local tech onsite again we will perform the connection attempt with the debugging enabled.
    FYI this is what the engineer wants to see.
    Here is the information that I need to see when the problem occurs:
    Disable/Disconnect the wireless client from the network – wait 1-2 mins
    Open Telnet/SSH session to the WLC CLI - (Use Putty/SecureCRT with logging enabled)
    type: Debug client
    Turn the wireless device back on and let it authenticate/associate to the wireless network.  Once the client experiences the problem, disable the debug process using the command: 
    debug disable-all
    Filename: DebugClient.TXT

  • Converged Access Design Help (Catalyst 3850 and WLC 5508...Mobility Oracle)

    Hello,
    I am an engineer working with a Cisco Gold Partner in Saudi Arabia. We have a large university as our client where they are constructing a new
    building and require our services to build the network infrastructure. Therefore, we are to implement the routing and switching infrastructure as
    well as the Wireless solution.
    At present, I have no issues in implementing the R&S infrastructure as it is very straight forward but it has implications on the deployment of
    the wireless solution which I explain further below. The R&S infrastructure comprises of the typical Core, Distribution, and Access layers and we
    are focusing on the local distribution and access switches with regards to the new building. The client has a converged Layer 3 network spanning
    from distribution layer to core layer and they are running EIGRP for this convergence. This is not a problem and has already been implemented.
    Yet, the challenge arises in deploying the WLAN infrastructure. The client already has a Cisco WLAN infrastructure in place where they have a
    large number of LAPs that are registered with their controllers in the Data Center. They have two WLC 5508 where one is the Primary and the other
    the Secondary. The local distribution switch to which the WLC are connected also is the gateway for the SVIs for the SSIDs that are configured on
    the controllers. This means that once the packets from the AP come in to the WLC, they are tagged with the correct VLAN and sent to the directly
    connected distribution switch which then routes it into the rest of the Layer 3 network. Interestingly, the WLC 5508 are running AireOS 7.6 and
    support the "New Mobility" feature. The two controllers have formed a Mobility Group (MG) between each other.
    Now, the new building will have two Catalyst 3850 switches installed where each one has a total of 40 AP licenses pre-installed and activated
    i.e. a total of 80 APs can be supported by the two switches. A total of 67 LAPs will be deployed in the new building which can be accommodated
    between the two switches and their integrated controller.
    Yet, based on my understanding and research about Converged Access is that, ideally, the Catalyst 3850 will only run the Mobility Agent (MA)
    feature while a central controller would provide the Mobility Controller (MC) service. unfortunately, there are not enough licenses on the
    existing WLC 5508 nor can we migrate the new licenses that will facilitate such a split deployment.
    This means that I would need to configure the two Catalyst 3850 as independent MC and form a MG between them. I have done this and tested this
    already and the mobility is working fine. But my concern is not about getting the Catalyst 3850 to work as this is simple but rather it is
    focused on creating a common Mobility Domain (MD) so that clients can roam from this new building to the rest of the campus while maintaining the
    state of their connections to the WLAN infrastructure.
    To make things more complicated, since the new building will have its own Layer 3 distribution switch and the Catalyst 3850 switches will connect
    to this distribution switch, it means that new VLANs and SVIs need to be created for the SSIDs broadcast in the new building. This means that new
    subnets need to be assigned to the SSIDs.
    As such, I have the following questions:
    Q1) If we create new SVIs for the SSIDs (same SSIDs names will be used in the new building as in the rest of the university campus) this means
    that new subnets will be assigned to these SSIDs. Now, I believe I have two options...one is to make the new Catalyst 3850s to be in the same MG
    as the existing WLC 5508 which then cater for Layer 3 client roaming or I have to treat this as a totally seperate WLAN network and follow on to
    the solution as per the next question. Please advise which is a better option?
    Q2) I could create separate MG i.e. the new building Catalyst 3850s can be in one MG and the existing controllers can be in another MG. I can
    then have one of the existing WLC 5508 (the primary one) to run the Mobility Oracle (MO) feature so as to create a single Mobility Domain (MD).
    Would this facilitate in Layer 3 client roaming and RRM for all the controllers in the same MD?
    Q3) If I do create a MD, how is this accomplished in such an environment since the documentation is severely limited in this regard?
    Please advise at your earliest. To assist further, I have attached a topology diagram which may aid in explaining the situation with more
    clarity. If these things are clarified, I will be better able to wrap my head around the technology and in turn service my clients better.
    Regards,
    Amir

    Hi Amir,
    Q1) If we create new SVIs for the SSIDs (same SSIDs names will be used in the new building as in the rest of the university campus) this means that new subnets will be assigned to these SSIDs. Now, I believe I have two options...one is to make the new Catalyst 3850s to be in the same MG as the existing WLC 5508 which then cater for Layer 3 client roaming or I have to treat this as a totally seperate WLAN network and follow on to the solution as per the next question. Please advise which is a better option?
    I would configure them in the same mobility group. Also configure same SPG for those two 3850 stacks if users are frequently roaming within these two buildings.
    Q2) I could create separate MG i.e. the new building Catalyst 3850s can be in one MG and the existing controllers can be in another MG. I can then have one of the existing WLC 5508 (the primary one) to run the Mobility Oracle (MO) feature so as to create a single Mobility Domain (MD). Would this facilitate in Layer 3 client roaming and RRM for all the controllers in the same MD?
    MO is not required (it is only for very large scale deployments)
    Q3) If I do create a MD, how is this accomplished in such an environment since the documentation is severely limited in this regard?
    Yes, documents are hard to find :(
    These notes may be useful to you based on my experience. I am running IOS-XE 3.6.1 in my production.
    http://mrncciew.com/2014/05/06/configuring-new-mobility/
    http://mrncciew.com/2013/12/14/3850ma-with-5760mc/
    HTH
    Rasika
    *** Pls rate all useful responses ****

  • Cisco WLC 5508 V 7.0.116.0 Help

    I have a WLC 5508, that has been working with AIR LAP 1522 AG-E-K9 and AIR LAP 1142N E K9 access points. I have deployed two
    AIR-CAP1552E-A-K9 AP's on the WLC. I had to upgrade to Version 7.0.116.0, and had to set the country code to US ( Was ZA). The good news is that on US country code the new 1552's works great.
    My problem now is to get the existing 1522 and 1142 AP's to work in conjunction with the 1552's on US country code.
    Any information would be greatly appreciated.
    Thank You in advance.

    George:
    Multiple country codes are not supported for MESH APs.
    You can only choose one country if you are using MESH APs whatever the model is.
    If you have MESH APs with multiple country regulatories I think the only way to go is to replace your APs so all of them to be under same regulatory.
    Features Not Supported on Mesh NetworksThese controller features are not supported on mesh networks:
    Multi-country support
    Load-based CAC (Mesh networks support only bandwidth-based, or static, CAC.)
    High availability (fast heartbeat and primary discovery join timer)
    EAP-FASTv1 and 802.1X authentication
    EAP-FASTv1 and 802.1X authentication
    Locally significant certificate
    Location-based services
    Reference: http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008072ea79.shtml
    HTH
    Amjad

  • Possible to setup something likes "protected port" on WLC 5508

    Hello,
    Let's say I have 3 APs, all connected to a WLC 5508
    Each AP has a computer that is connected to it, Computer A, B and C, all on the same Vlan with same SSID
    Is it possible to configure so
    A and B can not talk to each other but both can talk to C  ?
    Something like "protected port" feature in the switch world.
    Thanks

    Im looking for a solution for a WiFi network for our guests, where they dont need to talk to each other, and all need to talk to a wire internet gateway/router only.
    If you want to block guest SSID users from talking to each other then it's possible.  As Scott has pointed out, it's called "P2P Blocking Action".
    I do NOT recommend having guest and corporate share the same SSID.  I don't think it's best practice.

  • Cisco ISE 1.2 & Cisco WLC 5508 v7.6

    Hi all,
    we are planning to upgrade our WLC to 7.6 to fix a bug with FlexConnect Client ACLs but I have just seen on the Cisco ISE Compatibility table that the it only recommends up to v7.5 of the WLC 5508...
    Cisco have told me to steer clear of 7.5 as it is in a defferred status, so does anyone know, or have running in a lab or production, ISE1.2 with a 5508 WLC v7.6 NAD ?
    I would much rather know of any issues people are experiencing before hand than to have to go through a software upgrade and then rollback.
    Thanks all
    Mario De Rosa

    Hi Neno,
    right I have this almost working now.
    I have simplified the setup. I am not going to do any client provisioning at the moment.
    So I can connect to the corporate SSID using EAP-TLS and I can successfully push the branch data VLAN upon successful authorisation.
    Now I am trying to introduce the posture element & per user ACLs.
    I have defined the redirect ACL & Flex ACL on the vWLC however the NAC agent will not pop-up. The client is in the right VLAN and the redirect ACL seems to be getting applied as the client does get an IP through DHCP. However, the client cannot ping the ISE or access the guest portal when I open the browser.
    DNS resolution seems to be working fine.
    VLAN220 is my datacentre VLAN which the Management Interface on the controller is plugged in to.
    VLAN10 is the branch DATA VLAN.
    below is some output to give you some more details...
    (Cisco Controller) >show client detail 00:24:d6:97:b3:be
    Client MAC Address............................... 00:24:d6:97:b3:be
    Client Username ................................. [email protected]
    AP MAC Address................................... 18:33:9d:f0:21:80
    AP Name.......................................... test-flex-ap
    AP radio slot Id................................. 0
    Client State..................................... Associated
    Client NAC OOB State............................. Access
    Wireless LAN Id.................................. 2
    Hotspot (802.11u)................................ Not Supported
    BSSID............................................ 18:33:9d:f0:21:81
    Connected For ................................... 128 secs
    Channel.......................................... 6
    IP Address....................................... 10.130.130.120
    Gateway Address.................................. 10.130.130.1
    Netmask.......................................... 255.255.255.0
    IPv6 Address..................................... fe80::f524:1910:69f0:9482
    Association Id................................... 1
    Authentication Algorithm......................... Open System
    Reason Code...................................... 1
    Status Code...................................... 0
    Client CCX version............................... 4
    Client E2E version............................... 1
    --More-- or (q)uit
    Re-Authentication Timeout........................ 1651
    QoS Level........................................ Silver
    Avg data Rate.................................... 0
    Burst data Rate.................................. 0
    Avg Real time data Rate.......................... 0
    Burst Real Time data Rate........................ 0
    802.1P Priority Tag.............................. disabled
    CTS Security Group Tag........................... Not Applicable
    KTS CAC Capability............................... No
    WMM Support...................................... Enabled
      APSD ACs.......................................  BK  BE  VI  VO
    Power Save....................................... OFF
    Current Rate..................................... m13
    Supported Rates.................................. 1.0,2.0,5.5,11.0,6.0,9.0,
        ............................................. 12.0,18.0,24.0,36.0,48.0,
        ............................................. 54.0
    Mobility State................................... Local
    Mobility Move Count.............................. 0
    Security Policy Completed........................ No
    Policy Manager State............................. POSTURE_REQD
    Policy Manager Rule Created...................... Yes
    AAA Override ACL Name............................ POSTURE_REDIRECT_ACL
    AAA Override ACL Applied Status.................. Yes
    --More-- or (q)uit
    AAA Override Flex ACL Name....................... POSTURE_REDIRECT_ACL
    AAA Override Flex ACL Applied Status............. Yes
    AAA URL redirect................................. https://pdc-ise-man01.kier.group:8443/guestportal/gateway?sessionId=c8dc800a00000005b3e7e953&action=cpp
    Audit Session ID................................. c8dc800a00000005b3e7e953
    AAA Role Type.................................... none
    Local Policy Applied............................. none
    IPv4 ACL Name.................................... none
    FlexConnect ACL Applied Status................... Yes
    IPv4 ACL Applied Status.......................... Unavailable
    IPv6 ACL Name.................................... none
    IPv6 ACL Applied Status.......................... Unavailable
    Layer2 ACL Name.................................. none
    Layer2 ACL Applied Status........................ Unavailable
    mDNS Status...................................... Disabled
    mDNS Profile Name................................ none
    No. of mDNS Services Advertised.................. 0
    Policy Type...................................... WPA2
    Authentication Key Management.................... 802.1x
    Encryption Cipher................................ CCMP (AES)
    Protected Management Frame ...................... No
    Management Frame Protection...................... No
    EAP Type......................................... EAP-TLS
    FlexConnect Data Switching....................... Local
    --More-- or (q)uit
    FlexConnect Dhcp Status.......................... Local
    FlexConnect Vlan Based Central Switching......... No
    FlexConnect Authentication....................... Central
    Quarantine VLAN.................................. 0
    Access VLAN...................................... 220
    Client Capabilities:
          CF Pollable................................ Not implemented
          CF Poll Request............................ Not implemented
          Short Preamble............................. Implemented
          PBCC....................................... Not implemented
          Channel Agility............................ Not implemented
          Listen Interval............................ 10
          Fast BSS Transition........................ Not implemented
    Client Wifi Direct Capabilities:
          WFD capable................................ No
          Manged WFD capable......................... No
          Cross Connection Capable................... No
          Support Concurrent Operation............... No
    Fast BSS Transition Details:
    Client Statistics:
          Number of Bytes Received................... 33698
          Number of Bytes Sent....................... 19397
          Total Number of Bytes Sent................. 19397
    --More-- or (q)uit
          Total Number of Bytes Recv................. 33698
          Number of Bytes Sent (last 90s)............ 19397
          Number of Bytes Recv (last 90s)............ 33698
          Number of Packets Received................. 283
          Number of Packets Sent..................... 147
          Number of Interim-Update Sent.............. 0
          Number of EAP Id Request Msg Timeouts...... 0
          Number of EAP Id Request Msg Failures...... 0
          Number of EAP Request Msg Timeouts......... 0
          Number of EAP Request Msg Failures......... 0
          Number of EAP Key Msg Timeouts............. 0
          Number of EAP Key Msg Failures............. 0
          Number of Data Retries..................... 53
          Number of RTS Retries...................... 0
          Number of Duplicate Received Packets....... 2
          Number of Decrypt Failed Packets........... 0
          Number of Mic Failured Packets............. 0
          Number of Mic Missing Packets.............. 0
          Number of RA Packets Dropped............... 0
          Number of Policy Errors.................... 0
          Radio Signal Strength Indicator............ -42 dBm
          Signal to Noise Ratio...................... 41 dB
    Client Rate Limiting Statistics:
    --More-- or (q)uit
          Number of Data Packets Recieved............ 0
          Number of Data Rx Packets Dropped.......... 0
          Number of Data Bytes Recieved.............. 0
          Number of Data Rx Bytes Dropped............ 0
          Number of Realtime Packets Recieved........ 0
          Number of Realtime Rx Packets Dropped...... 0
          Number of Realtime Bytes Recieved.......... 0
          Number of Realtime Rx Bytes Dropped........ 0
          Number of Data Packets Sent................ 0
          Number of Data Tx Packets Dropped.......... 0
          Number of Data Bytes Sent.................. 0
          Number of Data Tx Bytes Dropped............ 0
          Number of Realtime Packets Sent............ 0
          Number of Realtime Tx Packets Dropped...... 0
          Number of Realtime Bytes Sent.............. 0
          Number of Realtime Tx Bytes Dropped........ 0
    Nearby AP Statistics:
          test-flex-ap(slot 0)
            antenna0: 14 secs ago.................... -51 dBm
            antenna1: 14 secs ago.................... -37 dBm
          test-flex-ap(slot 1)
            antenna0: 14 secs ago.................... -51 dBm
            antenna1: 14 secs ago.................... -54 dBm
    --More-- or (q)uit
    DNS Server details:
          DNS server IP ............................. 10.0.17.31
          DNS server IP ............................. 10.0.17.43
    Assisted Roaming Prediction List details:
     Client Dhcp Required:     False
    Allowed (URL)IP Addresses
    (Cisco Controller) >
    (Cisco Controller) >show wlan 2
    WLAN Identifier.................................. 2
    Profile Name..................................... Demo1x
    Network Name (SSID).............................. Demo1x
    Status........................................... Enabled
    MAC Filtering.................................... Disabled
    Broadcast SSID................................... Enabled
    AAA Policy Override.............................. Enabled
    Network Admission Control
    Client Profiling Status
        Radius Profiling ............................ Disabled
         DHCP ....................................... Disabled
         HTTP ....................................... Disabled
        Local Profiling ............................. Disabled
         DHCP ....................................... Disabled
         HTTP ....................................... Disabled
      Radius-NAC State............................... Enabled
      SNMP-NAC State................................. Disabled
      Quarantine VLAN................................ 0
    Maximum number of Associated Clients............. 0
    Maximum number of Clients per AP Radio........... 200
    --More-- or (q)uit
    Number of Active Clients......................... 1
    Exclusionlist Timeout............................ 60 seconds
    Session Timeout.................................. 1800 seconds
    User Idle Timeout................................ Disabled
    Sleep Client..................................... disable
    Sleep Client Timeout............................. 12 hours
    User Idle Threshold.............................. 0 Bytes
    NAS-identifier................................... mario-test-flex-vwlc
    CHD per WLAN..................................... Enabled
    Webauth DHCP exclusion........................... Disabled
    Interface........................................ management
    Multicast Interface.............................. Not Configured
    WLAN IPv4 ACL.................................... unconfigured
    WLAN IPv6 ACL.................................... unconfigured
    WLAN Layer2 ACL.................................. unconfigured
    mDNS Status...................................... Disabled
    mDNS Profile Name................................ unconfigured
    DHCP Server...................................... Default
    DHCP Address Assignment Required................. Disabled
    Static IP client tunneling....................... Disabled
    Quality of Service............................... Silver
    Per-SSID Rate Limits............................. Upstream      Downstream
    Average Data Rate................................   0             0
    --More-- or (q)uit
    Average Realtime Data Rate.......................   0             0
    Burst Data Rate..................................   0             0
    Burst Realtime Data Rate.........................   0             0
    Per-Client Rate Limits........................... Upstream      Downstream
    Average Data Rate................................   0             0
    Average Realtime Data Rate.......................   0             0
    Burst Data Rate..................................   0             0
    Burst Realtime Data Rate.........................   0             0
    Scan Defer Priority.............................. 4,5,6
    Scan Defer Time.................................. 100 milliseconds
    WMM.............................................. Allowed
    WMM UAPSD Compliant Client Support............... Disabled
    Media Stream Multicast-direct.................... Disabled
    CCX - AironetIe Support.......................... Enabled
    CCX - Gratuitous ProbeResponse (GPR)............. Disabled
    CCX - Diagnostics Channel Capability............. Disabled
    Dot11-Phone Mode (7920).......................... Disabled
    Wired Protocol................................... None
    Passive Client Feature........................... Disabled
    Peer-to-Peer Blocking Action..................... Disabled
    Radio Policy..................................... All
    DTIM period for 802.11a radio.................... 1
    DTIM period for 802.11b radio.................... 1
    --More-- or (q)uit
    Radius Servers
       Authentication................................ 10.0.16.111 1812
       Accounting.................................... 10.131.16.111 1813
          Interim Update............................. Disabled
          Framed IPv6 Acct AVP ...................... Prefix
       Dynamic Interface............................. Disabled
       Dynamic Interface Priority.................... wlan
    Local EAP Authentication......................... Disabled
    Security
       802.11 Authentication:........................ Open System
       FT Support.................................... Disabled
       Static WEP Keys............................... Disabled
       802.1X........................................ Disabled
       Wi-Fi Protected Access (WPA/WPA2)............. Enabled
          WPA (SSN IE)............................... Disabled
          WPA2 (RSN IE).............................. Enabled
             TKIP Cipher............................. Disabled
             AES Cipher.............................. Enabled
                                                                   Auth Key Management
             802.1x.................................. Enabled
             PSK..................................... Disabled
             CCKM.................................... Disabled
    --More-- or (q)uit
             FT-1X(802.11r).......................... Disabled
             FT-PSK(802.11r)......................... Disabled
             PMF-1X(802.11w)......................... Disabled
             PMF-PSK(802.11w)........................ Disabled
          FT Reassociation Timeout................... 20
          FT Over-The-DS mode........................ Enabled
          GTK Randomization.......................... Disabled
          SKC Cache Support.......................... Disabled
          CCKM TSF Tolerance......................... 1000
       WAPI.......................................... Disabled
       Wi-Fi Direct policy configured................ Disabled
       EAP-Passthrough............................... Disabled
       CKIP ......................................... Disabled
       Web Based Authentication...................... Disabled
       Web-Passthrough............................... Disabled
       Conditional Web Redirect...................... Disabled
       Splash-Page Web Redirect...................... Disabled
       Auto Anchor................................... Disabled
       FlexConnect Local Switching................... Enabled
       flexconnect Central Dhcp Flag................. Disabled
       flexconnect nat-pat Flag...................... Disabled
       flexconnect Dns Override Flag................. Disabled
       flexconnect PPPoE pass-through................ Disabled
    --More-- or (q)uit
       flexconnect local-switching IP-source-guar.... Disabled
       FlexConnect Vlan based Central Switching ..... Disabled
       FlexConnect Local Authentication.............. Disabled
       FlexConnect Learn IP Address.................. Enabled
       Client MFP.................................... Optional
       PMF........................................... Disabled
       PMF Association Comeback Time................. 1
       PMF SA Query RetryTimeout..................... 200
       Tkip MIC Countermeasure Hold-down Timer....... 60
       Eap-params.................................... Disabled
    AVC Visibilty.................................... Disabled
    AVC Profile Name................................. None
    Flow Monitor Name................................ None
    Split Tunnel (Printers).......................... Disabled
    Call Snooping.................................... Disabled
    Roamed Call Re-Anchor Policy..................... Disabled
    SIP CAC Fail Send-486-Busy Policy................ Disabled
    SIP CAC Fail Send Dis-Association Policy......... Disabled
    KTS based CAC Policy............................. Disabled
    Assisted Roaming Prediction Optimization......... Disabled
    802.11k Neighbor List............................ Disabled
    802.11k Neighbor List Dual Band.................. Disabled
    Band Select...................................... Disabled
    --More-- or (q)uit
    Load Balancing................................... Disabled
    Multicast Buffer................................. Disabled
     Mobility Anchor List
     WLAN ID     IP Address            Status
    802.11u........................................ Disabled
    MSAP Services.................................. Disabled
    Local Policy
    Priority  Policy Name
    (Cisco Controller) >
    when debugging the client during redirect, this is the output and I cannot spot anything wrong here...
    (Cisco Controller) >*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Adding mobile on LWAPP AP 18:33:9d:f0:21:80(1) 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Association received from mobile on BSSID 18:33:9d:f0:21:8e
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Global 200 Clients are allowed to AP radio
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Max Client Trap Threshold: 0  cur: 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be override for default ap group, marking intgrp NULL
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Re-applying interface policy for client 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2219)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2240)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be In processSsidIE:4850 setting Central switched to FALSE
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying site-specific Local Bridging override for station 00:24:d6:97:b3:be - vapId 2, site 'default-group', interface 'management'
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying Local Bridging Interface Policy for station 00:24:d6:97:b3:be - vlan 220, interface id 0, interface 'management'
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be processSsidIE  statusCode is 0 and status is 0 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be STA - rates (8): 140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be suppRates  statusCode is 0 and gotSuppRatesElement is 1 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Processing RSN IE type 48, length 22 for mobile 00:24:d6:97:b3:be
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Received RSN IE with 0 PMKIDs from mobile 00:24:d6:97:b3:be
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 8
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be unsetting PmkIdValidatedByAp
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Updating AID for REAP AP Client 18:33:9d:f0:21:80 - AID ===> 1
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Central switch is FALSE
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) DHCP required on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2for this client
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2 flex-acl-name: 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfMsAssoStateInc
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:24:d6:97:b3:be on AP 18:33:9d:f0:21:80 from Idle to Associated
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfPemAddUser2:session timeout forstation 00:24:d6:97:b3:be - Session Tout 0, apfMsTimeOut '0' and sessionTimerRunning flag is  0 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Stopping deletion of Mobile Station: (callerId: 48)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Func: apfPemAddUser2, Ms Timeout = 0, Session Timeout = 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Sending Assoc Response to station on BSSID 18:33:9d:f0:21:8e (status 0) ApVapId 2 Slot 1
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfProcessAssocReq (apf_80211.c:8294) Changing state for mobile 00:24:d6:97:b3:be on AP 18:33:9d:f0:21:80 from Associated to Associated
    *spamApTask6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Sent 1x initiate message to multi thread task for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be EAP-PARAM Debug - eap-params for Wlan-Id :2 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Station 00:24:d6:97:b3:be setting dot1x reauth timeout = 1800
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Connecting state
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Sending EAP-Request/Identity to mobile 00:24:d6:97:b3:be (EAP Id 1)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Received Identity Response (count=1) from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Resetting reauth count 1 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be EAP State update from Connecting to Authenticating for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Authenticating state
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=214) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be WARNING: updated EAP-Identifier 1 ===> 214 for STA 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 214)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Allocating EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 214, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=215) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 215)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 215, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=216) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 216)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 216, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=217) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 217)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 217, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=218) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 218)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 218, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=219) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 219)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 219, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=220) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 220)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 220, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=221) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 221)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 221, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=222) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 222)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 222, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=223) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 223)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 223, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=224) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 224)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 224, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=225) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 225)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 225, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Processing Access-Accept for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting web IPv4 acl from 255 to 255
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting web IPv4 Flex acl from 65535 to 65535
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Username entry ([email protected]) created for mobile, length = 253 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Username entry ([email protected]) created in mscb for mobile, length = 253 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be override for default ap group, marking intgrp NULL
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 220
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Re-applying interface policy for client 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2219)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2240)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 1 on mobile 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Inserting AAA Override struct for mobile
        MAC: 00:24:d6:97:b3:be, source 4
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting re-auth timeout to 1800 seconds, got from WLAN config.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Station 00:24:d6:97:b3:be setting dot1x reauth timeout = 1800
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Creating a PKC PMKID Cache entry for station 00:24:d6:97:b3:be (RSN 2)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting MSCB PMK Cache Entry 0 for station 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 8
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Adding BSSID 18:33:9d:f0:21:8e to PMKID cache at index 0 for station 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: New PMKID: (16)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410:      [0000] 6f d1 ce 84 08 74 41 a5 06 6b 89 02 c9 e9 f8 c8
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Disabling re-auth since PMK lifetime can take care of same.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be unsetting PmkIdValidatedByAp
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Client in Posture Reqd state. PMK cache not updated.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAP-Success to mobile 00:24:d6:97:b3:be (EAP Id 225)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Freeing AAACB from Dot1xCB as AAA auth is done for  mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be EAPOL Header: 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00000000: 02 03 5f 00                                       .._.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Found an cache entry for BSSID 18:33:9d:f0:21:8e in PMKID cache at index 0 of station 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Found an cache entry for BSSID 18:33:9d:f0:21:8e in PMKID cache at index 0 of station 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410:      [0000] 6f d1 ce 84 08 74 41 a5 06 6b 89 02 c9 e9 f8 c8
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Starting key exchange to mobile 00:24:d6:97:b3:be, data packets will be dropped
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Entering Backend Auth Success state (id=225) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Received Auth Success while in Authenticating state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Authenticated state
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Received EAPOL-Key from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Received EAPOL-key in PTK_START state (message 2) from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be PMK: Sending cache add
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Stopping retransmission timer for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be EAPOL Header: 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00000000: 02 03 5f 00                                       .._.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
       state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
       state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Received EAPOL-Key from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Stopping retransmission timer for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Freeing EAP Retransmit Bufer for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be apfMs1xStateInc
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state 8021X_REQD (3)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Central switch is FALSE
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Sending the Central Auth Info
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Central Auth Info Allocated PMKLen = 32
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: EapolReplayCounter: 00 00 00 00 00 00 00 01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: EapolReplayCounter: 00 00 00 00 00 00 00 01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be PMK: pmkActiveIndex = 0
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be EapolReplayCounter: 00 00 00 00 00 00 00 01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
    apfMsEntryType = 0 apfMsEapType = 13
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) DHCP required on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2for this client
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Not Using WMM Compliance code qosCap 00
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2 flex-acl-name:POSTURE_REDIRECT_ACL 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 6166, Adding TMP rule
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Adding Fast Path rule
      type = Airespace AP - Learn IP address
      on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
      IPv4 ACL ID = 255, IPv
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206  Local Bridging Vlan = 220, Local Bridging intf id = 0
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 5761, Adding TMP rule
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Replacing Fast Path rule
      type = Airespace AP - Learn IP address
      on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
      IPv4 ACL ID = 255, 
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206  Local Bridging Vlan = 220, Local Bridging intf id = 0
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
    *pemReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
    *pemReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
    *spamApTask6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be spamEncodeCentralAuthInoMsPayload: msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
    apfMsEntryType = 0 pmkLen = 32
    *DHCP Socket Task: Aug 12 10:58:24.546: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 325,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 10:58:24.546: 00:24:d6:97:b3:be DHCP setting server from ACK (server 10.0.17.85, yiaddr 10.130.130.120)
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 DHCP_REQD (7) Change state to WEBAUTH_REQD (8) last state DHCP_REQD (7)
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) pemAdvanceState2 6671, Adding TMP rule
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Replacing Fast Path rule
      type = Airespace AP Client - ACL passthru
      on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
      IPv4 A
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206  Local Bridging Vlan = 220, Local Bridging intf id = 0
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Successfully plumbed mobile rule (IPv4 ACL ID 1, IPv6 ACL ID 255, L2 ACL ID 255)
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be Plumbing web-auth redirect rule due to user logout
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be Assigning Address 10.130.130.120 to mobile 
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be DHCP success event for client. Clearing dhcp failure count for interface management.
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be DHCP success event for client. Clearing dhcp failure count for interface management.
    *pemReceiveTask: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 Added NPU entry of type 2, dtlFlags 0x0
    *IPv6_Msg_Task: Aug 12 10:58:25.330: 00:24:d6:97:b3:be Pushing IPv6 Vlan Intf ID 0: fe80:0000:0000:0000:f524:1910:69f0:9482 , and MAC: 00:24:D6:97:B3:BE , Binding to Data Plane. SUCCESS !! dhcpv6bitmap 0
    *IPv6_Msg_Task: Aug 12 10:58:25.330: 00:24:d6:97:b3:be Link Local address fe80::f524:1910:69f0:9482 updated to mscb. Not Advancing pem state.Current state: mscb in apfMsMmInitial mobility state and client state APF_MS_STATE_A
    *DHCP Socket Task: Aug 12 10:58:28.581: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 10:58:28.589: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 11:00:07.959: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 11:00:07.967: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 11:01:59.153: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    Can you see any obvious reason why the NAC agent wont pop up?
    Thanks
    Mario

  • Deployment of WLC-5508 with 2702i-D have performance issue.

    Hi Team,
    We have centrally deployed WLC-5508 with 50 AP licence along with HA scenario. we have 3 locations.
    1- HQ. have 26 AP with POWINJ5.
    2- Branch location A- 8 AP with POWINJ5.
    3. Branch location B have 8 AP with POWINJ4.
    my exception is to achieve that  single SSID with dynamic VLAN from group police (NPS). MY HO have 26 AP and those are working in local mode.
    and branches are connected through flexconnect mode. and all are working with different-2 NPS. 
    Now i am facing a problem with this deployment are following.
    1- branch A have performance issue.
    2- HQ have performance issue.
    3- i don't want to go with dedicated NPS for every location. 
    In order to achieve this deployment i want only single SSID with primary and secondary NPS at my HQ with dynamic VLAN for respective departmental users vlans..
    above is my problem and concern. otherwise i am successfully achieving this solution with dedicated NPS with single group policy. but when i am going forward to achieve my expectation that time i am facing authentication issue at my HQ and sometimes am not able to get proper VLAN IPs. at my HQ. 
    kindly help me in that to understand where I am doing wrong things to achieve my expectation. 
    Thanks.
    Nalin    

    I am facing 2 different problems.
    1st issue- in existing setup we have throughput issue. (while downloading or uploading any data from the internet or Intranet,  that time wireless clients are facing slowness of the Speed. and same time when i am trying from LAN i am not facing any issue)
    2nd Issue- I want to achieve only single SSID with primary and secondary NPS (AD group is bind with vlan Attributes) with dynamic VLAN for respective departmental users.
    for Issue no 2 i have created SSID to achieve the single ssid parameter for every location. in order to achieve i have change all access points mode local to Flexconnect mode after that i have created AP groups location wise and then create flexconnect Groups where i have mapped all the vlan through AAA VLAN-ACL mapping. created interface group and mapped all the vlans in that group. 
    for more understanding please go through the below mentioned CLI view.
    Cisco Controller) >show wlan apgroups
    Total Number of AP Groups........................ 4
    Site Name........................................ GURGAON-AP-GROUP
    Site Description................................. GURGAON-AP-GROUP
    Venue Group Code................................. Unspecified
    Venue Type Code.................................. Unspecified
    NAS-identifier................................... Fractal-WLC1
    Client Traffic QinQ Enable....................... FALSE
    DHCPv4 QinQ Enable............................... FALSE
    AP Operating Class............................... Not-configured
    Capwap Prefer Mode............................... Not-configured
    RF Profile
    2.4 GHz band..................................... <none>
    5 GHz band....................................... <none>
    WLAN ID          Interface          Network Admission Control          Radio Pol                                                                                        icy
     3               gurgaon-interface    Disabled                          None
    --More-- or (q)uit
     4               gurgaon-guest        Disabled                          None
    *AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
    AP Name             Slots  AP Model             Ethernet MAC       Location          Port  Country  Priority
    GUR-AP-01            2     AIR-CAP2702I-D-K9    f4:4e:05:78:ae:e4  default location  1     IN       1
    GUR-AP-05            2     AIR-CAP2702I-D-K9    f4:4e:05:80:b5:18  default location  1     IN       1
    GUR-AP-03            2     AIR-CAP2702I-D-K9    bc:16:65:13:71:00  default location  1     IN       1
    GUR-AP-07            2     AIR-CAP2702I-D-K9    f4:4e:05:80:b3:f8  default location  1     IN       1
    GUR-AP-06            2     AIR-CAP2702I-D-K9    f4:4e:05:80:b3:e0  default location  1     IN       1
    GUR-AP-08            2     AIR-CAP2702I-D-K9    f4:4e:05:45:78:98  default location  1     IN       1
    GUR-AP-02            2     AIR-CAP2702I-D-K9    f4:4e:05:80:b3:2c  default location  1     IN       1
    GUR-AP-04            2     AIR-CAP2702I-D-K9    f4:4e:05:78:ae:64  default location  1     IN       1
    GUR-AP-09            2     AIR-CAP2702I-D-K9    f4:4e:05:80:b4:44  default location  1     IN       1
    Site Name........................................ MUMBAI-AP-GROUP
    Site Description................................. MUMBAI-AP-GROUP
    Venue Group Code................................. Unspecified
    Venue Type Code.................................. Unspecified
    --More-- or (q)uit
    NAS-identifier................................... Fractal-WLC1
    Client Traffic QinQ Enable....................... FALSE
    DHCPv4 QinQ Enable............................... FALSE
    AP Operating Class............................... Not-configured
    Capwap Prefer Mode............................... Not-configured
    RF Profile
    2.4 GHz band..................................... <none>
    5 GHz band....................................... <none>
    WLAN ID          Interface          Network Admission Control          Radio Policy
     1               group for mumbai     Disabled                          None
     2               guest wifi           Disabled                          None
    *AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
    AP Name             Slots  AP Model             Ethernet MAC       Location          Port  Country  Priority
    FAL-7-AP08           2     AIR-CAP2702I-D-K9    f0:7f:06:8d:24:d8         7th Floor  1     IN       3
    --More-- or (q)uit
    FAL-7-AP10           2     AIR-CAP2702I-D-K9    f0:7f:06:8d:25:18         7th Floor  1     IN       1
    FAL-7-AP14           2     AIR-CAP2702I-D-K9    f0:7f:06:bf:ad:e8         7th Floor  1     IN       1
    FAL-7-AP01           2     AIR-CAP2702I-D-K9    f0:7f:06:bf:b0:4c         7th Floor  1     IN       1
    FAL-7-AP07           2     AIR-CAP2702I-D-K9    f0:7f:06:30:92:bc         7th Floor  1     IN       1
    FAL-7-AP13           2     AIR-CAP2702I-D-K9    f0:7f:06:30:91:80         7th Floor  1     IN       1
    FAL-7-AP02           2     AIR-CAP2702I-D-K9    f0:7f:06:30:91:94         7th Floor  1     IN       1
    FAL-7-AP05           2     AIR-CAP2702I-D-K9    f0:7f:06:30:91:e8         7th Floor  1     IN       1
    FAL-7-AP12           2     AIR-CAP2702I-D-K9    f0:7f:06:8d:25:f0         7th Floor  1     IN       3
    FAL-7-AP03           2     AIR-CAP2702I-D-K9    f0:7f:06:8d:25:e4         7th Floor  1     IN       1
    FAL-7-AP06           2     AIR-CAP2702I-D-K9    f0:7f:06:30:91:84         7th Floor  1     IN       3
    FAL-7-AP04           2     AIR-CAP2702I-D-K9    f0:7f:06:bf:b0:14         7th Floor  1     IN       1
    FAL-7-AP09           2     AIR-CAP2702I-D-K9    f0:7f:06:92:b4:c8         7th Floor  1     IN       3
    FAL-7-AP11           2     AIR-CAP2702I-D-K9    f0:7f:06:30:93:08         7th Floor  1     IN       1
    Site Name........................................ MUMBAI-THIRD-FLOOR-AP
    Site Description................................. MUMBAI-THIRD-FLOOR-AP
    Venue Group Code................................. Unspecified
    Venue Type Code.................................. Unspecified
    NAS-identifier................................... Fractal-WLC1
    Client Traffic QinQ Enable....................... FALSE
    --More-- or (q)uit
    DHCPv4 QinQ Enable............................... FALSE
    AP Operating Class............................... Not-configured
    Capwap Prefer Mode............................... Not-configured
    RF Profile
    2.4 GHz band..................................... <none>
    5 GHz band....................................... <none>
    WLAN ID          Interface          Network Admission Control          Radio Policy
     1               group for mumbai     Disabled                          None
     2               guest wifi           Disabled                          None
    *AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
    AP Name             Slots  AP Model             Ethernet MAC       Location          Port  Country  Priority
    FAL-3-AP07           2     AIR-CAP2702I-D-K9    f0:7f:06:30:91:a4         3rd Floor  1     IN       3
    FAL-3-AP09           2     AIR-CAP2702I-D-K9    f0:7f:06:8d:25:94         3rd Floor  1     IN       3
    FAL-3-AP11           2     AIR-CAP2702I-D-K9    f4:0f:1b:73:00:74  3rd Floor- Eurek  1     IN       3
    FAL-3-AP06           2     AIR-CAP2702I-D-K9    f0:7f:06:bf:ae:d0         3rd Floor  1     IN       3
    --More-- or (q)uit
    FAL-3-AP10           2     AIR-CAP2702I-D-K9    f0:7f:06:92:b5:88         3rd Floor  1     IN       3
    FAL-3-AP08           2     AIR-CAP2702I-D-K9    f0:7f:06:92:b4:9c         3rd Floor  1     IN       3
    FAL-3-AP03           2     AIR-CAP2702I-D-K9    f0:7f:06:bf:af:a0         3rd Floor  1     IN       1
    FAL-3-AP12           2     AIR-CAP2702I-D-K9    f0:7f:06:92:b3:fc  3rd Floor- Eurek  1     IN       3
    FAL-3-AP02           2     AIR-CAP2702I-D-K9    f0:7f:06:8d:25:28         3rd Floor  1     IN       3
    FAL-3-AP01           2     AIR-CAP2702I-D-K9    f0:7f:06:92:b4:f4         3rd Floor  1     IN       3
    FAL-3-AP04           2     AIR-CAP2702I-D-K9    f0:7f:06:30:92:8c         3rd Floor  1     IN       2
    FAL-3-AP05           2     AIR-CAP2702I-D-K9    f0:7f:06:30:91:f4         3rd Floor  1     IN       3
    Site Name........................................ RAHEJA-AP-GROUP
    Site Description................................. RAHEJA-AP-GROUP
    Venue Group Code................................. Unspecified
    Venue Type Code.................................. Unspecified
    NAS-identifier................................... Fractal-WLC1
    Client Traffic QinQ Enable....................... FALSE
    DHCPv4 QinQ Enable............................... FALSE
    AP Operating Class............................... Not-configured
    Capwap Prefer Mode............................... Not-configured
    RF Profile
    --More-- or (q)uit
    2.4 GHz band..................................... <none>
    5 GHz band....................................... <none>
    WLAN ID          Interface          Network Admission Control          Radio Policy
     5               raheja-interface     Disabled                          None
     2               raheja-guest         Disabled                          None
    *AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
    AP Name             Slots  AP Model             Ethernet MAC       Location          Port  Country  Priority
    FAL-RAHEJA-AP04      2     AIR-CAP2702I-D-K9    f0:7f:06:8d:24:1c  Near Meeting Roo  1     IN       3
    FAL-RAHEJA-AP02      2     AIR-CAP2702I-D-K9    f0:7f:06:8d:37:3c   Confrennce Room  1     IN       3
    FAL-RAHEJA-AP03      2     AIR-CAP2702I-D-K9    f0:7f:06:30:93:48  Near Confrence R  1     IN       3
    FAL-RAHEJA-AP05      2     AIR-CAP2702I-D-K9    f0:7f:06:bf:ae:c0  Near Meeting Roo  1     IN       3
    FAL-RAHEJA-AP06      2     AIR-CAP2702I-D-K9    f0:7f:06:92:b3:a0  Near Server Room  1     IN       3
    FAL-RAHEJA-AP01      2     AIR-CAP2702I-D-K9    f0:7f:06:92:b3:20    Reception Area  1     IN       3
    FAL-RAHEJA-AP08      2     AIR-CAP2702I-D-K9    f0:7f:06:8d:25:68  USER BAY ROAD si  1     IN       1
    FAL-RAHEJA-AP09      2     AIR-CAP2702I-D-K9    f0:7f:06:92:b4:d4     Training Room  1     IN       1
    --More-- or (q)uit
    Site Name........................................ default-group
    Site Description................................. <none>
    NAS-identifier................................... Fractal-WLC1
    Client Traffic QinQ Enable....................... FALSE
    DHCPv4 QinQ Enable............................... FALSE
    AP Operating Class............................... Not-configured
    Capwap Prefer Mode............................... Not-configured
    RF Profile
    2.4 GHz band..................................... <none>
    5 GHz band....................................... <none>
    WLAN ID          Interface          Network Admission Control          Radio Policy
     1               group for mumbai     Disabled                          None
     2               guest wifi           Disabled                          None
     3               gurgaon-interface    Disabled                          None
     4               gurgaon-guest        Disabled                          None
     5               raheja-interface     Disabled                          None
     6               test                 Disabled                          None
    Cisco Controller) >show flexconnect group summary
    FlexConnect Group Summary: Count: 4
    Group Name                # Aps
    Gurgaon-AP                         9
    HQ-3RD-FLR-AP-GROUP                        12
    HQ-7THFLR-AP-GROUP                         14
    Raheja-AP-Group                            8
    (Cisco Controller) >show flexconnect group detail Gurgaon-AP
    Number of AP's in Group: 9
    bc:16:65:13:71:00    GUR-AP-03     Joined    Flexconnect
    f4:4e:05:45:78:98    GUR-AP-08     Joined    Flexconnect
    f4:4e:05:78:ae:64    GUR-AP-04     Joined    Flexconnect
    f4:4e:05:78:ae:e4    GUR-AP-01     Joined    Flexconnect
    f4:4e:05:80:b3:2c    GUR-AP-02     Joined    Flexconnect
    f4:4e:05:80:b3:e0    GUR-AP-06     Joined    Flexconnect
    f4:4e:05:80:b3:f8    GUR-AP-07     Joined    Flexconnect
    f4:4e:05:80:b4:44    GUR-AP-09     Joined    Flexconnect
    f4:4e:05:80:b5:18    GUR-AP-05     Joined    Flexconnect
    Efficient AP Image Upgrade ..... Disabled
    Master-AP-Mac     Master-AP-Name                    Model      Manual
    Group Radius Servers Settings:
    Type           Server Address    Port
                                             Primary       Unconfigured      Unconfigured
                                                                                          Secondary     Unconfigured      Unconfigured
    --More-- or (q)uit
    Group Radius AP Settings:
    AP RADIUS server............ Disabled
    EAP-FAST Auth............... Disabled
    LEAP Auth................... Disabled
    EAP-TLS Auth................ Disabled
    EAP-TLS CERT Download....... Disabled
    PEAP Auth................... Disabled
    Server Key Auto Generated... No
    Server Key..................     <hidden>
    Authority ID................ 436973636f0000000000000000000000
    Authority Info.............. Cisco A_ID
    PAC Timeout................. 0
    Multicast on Overridden interface config: Disabled
    DHCP Broadcast Overridden interface config: Disabled
    Number of User's in Group: 0
    Vlan :........................................... 203
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 205
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 204
    --More-- or (q)uit
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 206
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 207
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 208
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 209
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 210
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 211
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 212
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    --More-- or (q)uit
    Vlan :........................................... 216
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 217
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 218
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Group-Specific FlexConnect Wlan-Vlan Mapping:
    WLAN ID     Vlan ID
    WLAN ID   SSID                            Central-Dhcp  Dns-Override  Nat-Pat
    (Cisco Controller) >
    (Cisco Controller) >show wlan summary
    Number of WLANs.................................. 6
    WLAN ID  WLAN Profile Name / SSID               Status    Interface Name        PMIPv6 Mobility
    1        FRACTAL-EMP-MUMBAI / FRACTAL           Enabled   group for mumbai      none
    2        FRACTAL-GUEST / FRACTAL-GUEST          Enabled   guest wifi            none
    3        FRACTAL-EMP-GURGAON / FRACTAL-GURGAON  Enabled   gurgaon-interface     none
    4        GURGAON-GUEST / FRACTAL-GUEST-GURGAON  Enabled   gurgaon-guest         none
    5        RAHEJA-EMP-WIRELESS / FRACTAL-R        Enabled   raheja-interface      none
    6        TEST-SSID / TEST-SSID                  Enabled   test                  none
    hope this will give you proper understanding.  

  • EAP-TLS with WLC 5508, Microsoft NPS and custom EKU OID´s

    We are trying to implement EAP-TLS with client certificates that have a custom EKU OID to distinguish the WLAN clients. The Microsoft Press Book
    Windows Server 2008 PKI and Certificate Security gives an example on how to configure a policy in NPS that matches specific EKU OID´s. At the moment we have two policies that have an allowed-certificate-oid configured that matches the OID´s in our certificates, but our setup is not working as expected. Authentications will only be successful, if the client authenticates with the certificate that is matched by the first policy rule.
    For example:
    Policy 1: allowed-certificate-OID --> corporate
    Policy 2: allowed-certificate-OID --> private
    Client authenticates with EKU corporate --> success
    Client authenticates with EKU private --> reject
    My expectation was, that if Policy 1 will not match the NPS goes over to Policy 2 and tries to authenticate the client.
    Has anyone a simmilar setup or can help to figure out what is going wrong?
    We have a WLC 5508 with Software Version                 7.4.100.0 and a NPS on a Windows Server 2008 R2
    regards
    Fabian

    The policy rejects and the NPS goes to the next policy, only if the user does not belong to the configured group.
    This means I need to have one AD group per application policy, but that will not solve my problem. A user could belong to more than one group, depending on how many devices he/she has. It will work with one group only for each user, because the first policy that matches a AD group, the user belongs to, could have a OID that is not in the certificate. This would cause a recejct with reason code 73:
    The purposes that are configured in the Application Policies extensions, also called Enhanced Key Usage (EKU) extensions, section of the user or computer certificate are not valid or are missing. The user or computer certificate must be configured with the Client Authentication purpose in Application Policies extensions. The object identifier for Client Authentication is 1.3.6.1.5.5.7.3.2.
    The certificate does include this OID but not the custom EKU.

  • WLC 5508 Multiple Interfaces for Multiple SSIDs

    Hello guys,
    I am trying to build a new network from scratch, I have the WLC 5508 w/ Aironet 3600e APs connected to my Netgear Smart Switches and a Linksys RV082 router that I'm using as my DHCP server with several VLANs for several stuff on my Switches.
    I have 2 questions:
    1. Can I have 5 Interfaces configured on 5 different VLANs, each SSID on each a different Port:
    Port 1: Controller management only=> 192.168.x.x /24
    Port 2: SSID 1: WiFi Internal=> 172.16.x.x/12 (Radius Auth with no sharing)
    Port 3: SSID 2: WiFi Internal w/ sharing=> 192.168.x.x/24 (Radius Auth with sharing)
    Port 4 :SSID 3: WiFi Guest=> 10.0.x.x/8 (Web Auth)
    Port 5: SSID 4: WiFi IT=> 192.168.x.x/24 ( Radius or certificate Auth with access to the controller management interface)
    2. How can I use the Controller as the DHCP server for all the WiFi traffic, and how should that be configured to work with my other DHCP server?

    Yes you can... but you have to disable LAG.  Each post will need to be connected to a dot1q trunk and you will only allow the vlan that is required for that port.  Also on the interface, you will define what port is primary and what is backup.  I'm guessing you will not be using the backup port.  For example... port 1 that connects to a trunk port will only allow the management vlan.  Here is a link to setup dhcp on the WLC
    http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a0080af5d13.shtml
    Thanks,
    Scott
    Help out other by using the rating system and marking answered questions as "Answered"

  • IPhones not taking ipv4 addresses on Unified Wireless (WLC 5508 and AP 3602)

    This is a really odd one...
    Earlier this week we started having issues with our BYOD wireless network (802.1x, WPA2+AES) but only with Apple devices (iphone and ipad). Employees with Android or Windows phones are not having any problems at all.
    A brief summary of what's observable for the issue:
    Radius authentication succeeds (PASS observable in ACS logs)
    IPhone status viewed on both controllers (foreign anchor in DMZ as well as corporate WLC) shows phone associated.
    Debug client output shows an IPv4 address is actually being assigned to the phone however it appears to ignore it and restart the DHCP request process so debug output shows what looks to be a loop of DHCP request and offer stages.
    Infrastructure notes
    Cisco WLC 5508s are all running 7.4.121.0 (tried rolling back to 7.2.110.0 .....didn't help)
    APs are all 3602I-N-K9
    DHCP for the BYOD network is running on the anchor in the DMZ however this was temporarily moved to a switch (had no effect).
    Any ideas?
    DHCP Loop:
    *mmListen: Apr 30 11:44:50.476: a4:c3:61:7a:1a:4f 0.0.0.0 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206  Local Bridging Vlan = 93, Local Bridging intf id = 12
    *mmListen: Apr 30 11:44:50.476: a4:c3:61:7a:1a:4f 0.0.0.0 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255)
    *pemReceiveTask: Apr 30 11:44:50.476: a4:c3:61:7a:1a:4f Set bi-dir guest tunnel for a4:c3:61:7a:1a:4f as in Export Anchor role
    *pemReceiveTask: Apr 30 11:44:50.476: a4:c3:61:7a:1a:4f 0.0.0.0 Added NPU entry of type 1, dtlFlags 0x4
    *pemReceiveTask: Apr 30 11:44:50.476: a4:c3:61:7a:1a:4f Pushing IPv6: fe80:0000:0000:0000: 0c00:0c94:459e:a9db , and MAC: A4:C3:61:7A:1A:4F , Binding to Data Plane. SUCCESS !!
    *DHCP Socket Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP received op BOOTREQUEST (1) (len 308,vlan 92, port 13, encap 0xec05)
    *DHCP Socket Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP selecting relay 1 - control block settings:
                            dhcpServer: 172.24.13.251, dhcpNetmask: 0.0.0.0,
                            dhcpGateway: 0.0.0.0, dhcpRelay: 172.24.16.251  VLAN: 93
    *DHCP Socket Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP selected relay 1 - 172.24.13.251 (local address 172.24.16.251, gateway 172.24.16.254, VLAN 93, port 13)
    *DHCP Socket Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
    *DHCP Socket Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP   xid: 0x7e549f4a (2119475018), secs: 0, flags: 0
    *DHCP Socket Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP   chaddr: a4:c3:61:7a:1a:4f
    *DHCP Socket Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP   siaddr: 0.0.0.0,  giaddr: 172.24.16.251
    *DHCP Socket Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP selecting relay 2 - control block settings:
                            dhcpServer: 172.24.13.251, dhcpNetmask: 0.0.0.0,
                            dhcpGateway: 0.0.0.0, dhcpRelay: 172.24.16.251  VLAN: 93
    *DHCP Socket Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP selected relay 2 - NONE
    *DHCP Proxy Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP received op BOOTREPLY (2) (len 572,vlan 0, port 0, encap 0x0)
    *DHCP Proxy Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP sending packet in EoIP tunnel to foreign 10.65.31.8 (len 346)
    *DHCP Proxy Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP transmitting DHCP OFFER (2)
    *DHCP Proxy Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP   op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
    *DHCP Proxy Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP   xid: 0x7e549f4a (2119475018), secs: 0, flags: 0
    *DHCP Proxy Task: Apr 30 11:44:50.480: a4:c3:61:7a:1a:4f DHCP   chaddr: a4:c3:61:7a:1a:4f
    *DHCP Proxy Task: Apr 30 11:44:50.480: a4:c3:61:7a:1a:4f DHCP   ciaddr: 0.0.0.0,  yiaddr: 172.24.16.102
    *DHCP Proxy Task: Apr 30 11:44:50.480: a4:c3:61:7a:1a:4f DHCP   siaddr: 0.0.0.0,  giaddr: 0.0.0.0
    *DHCP Proxy Task: Apr 30 11:44:50.480: a4:c3:61:7a:1a:4f DHCP   server id: 0.0.0.0  rcvd server id: 172.24.13.251
    *DHCP Socket Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP received op BOOTREQUEST (1) (len 308,vlan 92, port 13, encap 0xec05)
    *DHCP Socket Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP selecting relay 1 - control block settings:
                            dhcpServer: 172.24.13.251, dhcpNetmask: 0.0.0.0,
                            dhcpGateway: 0.0.0.0, dhcpRelay: 172.24.16.251  VLAN: 93
    *DHCP Socket Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP selected relay 1 - 172.24.13.251 (local address 172.24.16.251, gateway 172.24.16.254, VLAN 93, port 13)
    *DHCP Socket Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
    *DHCP Socket Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP   xid: 0x7e549f4a (2119475018), secs: 1, flags: 0
    *DHCP Socket Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP   chaddr: a4:c3:61:7a:1a:4f
    *DHCP Socket Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP   siaddr: 0.0.0.0,  giaddr: 172.24.16.251
    *DHCP Socket Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP selecting relay 2 - control block settings:
                            dhcpServer: 172.24.13.251, dhcpNetmask: 0.0.0.0,
                            dhcpGateway: 0.0.0.0, dhcpRelay: 172.24.16.251  VLAN: 93
    *DHCP Socket Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP selected relay 2 - NONE
    *DHCP Proxy Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP received op BOOTREPLY (2) (len 572,vlan 0, port 0, encap 0x0)
    *DHCP Proxy Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP sending packet in EoIP tunnel to foreign 10.65.31.8 (len 346)
    *DHCP Proxy Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP transmitting DHCP OFFER (2)
    *DHCP Proxy Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP   op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
    *DHCP Proxy Task: Apr 30 11:44:51.650: a4:c3:61:7a:1a:4f DHCP   xid: 0x7e549f4a (2119475018), secs: 0, flags: 0
    *DHCP Proxy Task: Apr 30 11:44:51.650: a4:c3:61:7a:1a:4f DHCP   chaddr: a4:c3:61:7a:1a:4f
    *DHCP Proxy Task: Apr 30 11:44:51.650: a4:c3:61:7a:1a:4f DHCP   ciaddr: 0.0.0.0,  yiaddr: 172.24.16.102
    *DHCP Proxy Task: Apr 30 11:44:51.650: a4:c3:61:7a:1a:4f DHCP   siaddr: 0.0.0.0,  giaddr: 0.0.0.0
    *DHCP Proxy Task: Apr 30 11:44:51.650: a4:c3:61:7a:1a:4f DHCP   server id: 0.0.0.0  rcvd server id: 172.24.13.251
    *DHCP Socket Task: Apr 30 11:44:53.754: a4:c3:61:7a:1a:4f DHCP received op BOOTREQUEST (1) (len 308,vlan 92, port 13, encap 0xec05)
    *DHCP Socket Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP selecting relay 1 - control block settings:
                            dhcpServer: 172.24.13.251, dhcpNetmask: 0.0.0.0,
                            dhcpGateway: 0.0.0.0, dhcpRelay: 172.24.16.251  VLAN: 93
    *DHCP Socket Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP selected relay 1 - 172.24.13.251 (local address 172.24.16.251, gateway 172.24.16.254, VLAN 93, port 13)
    *DHCP Socket Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
    *DHCP Socket Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP   xid: 0x7e549f4a (2119475018), secs: 3, flags: 0
    *DHCP Socket Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP   chaddr: a4:c3:61:7a:1a:4f
    *DHCP Socket Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP   siaddr: 0.0.0.0,  giaddr: 172.24.16.251
    *DHCP Socket Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP selecting relay 2 - control block settings:
                            dhcpServer: 172.24.13.251, dhcpNetmask: 0.0.0.0,
                            dhcpGateway: 0.0.0.0, dhcpRelay: 172.24.16.251  VLAN: 93
    *DHCP Socket Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP selected relay 2 - NONE
    *DHCP Proxy Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP received op BOOTREPLY (2) (len 572,vlan 0, port 0, encap 0x0)
    *DHCP Proxy Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP sending packet in EoIP tunnel to foreign 10.65.31.8 (len 346)
    *DHCP Proxy Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP transmitting DHCP OFFER (2)
    *DHCP Proxy Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP   op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
    *DHCP Proxy Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP   xid: 0x7e549f4a (2119475018), secs: 0, flags: 0
    *DHCP Proxy Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP   chaddr: a4:c3:61:7a:1a:4f
    *DHCP Proxy Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP   ciaddr: 0.0.0.0,  yiaddr: 172.24.16.102
    *DHCP Proxy Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP   siaddr: 0.0.0.0,  giaddr: 0.0.0.0
    *DHCP Proxy Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP   server id: 0.0.0.0  rcvd server id: 172.24.13.251
    *DHCP Socket Task: Apr 30 11:44:58.594: a4:c3:61:7a:1a:4f DHCP received op BOOTREQUEST (1) (len 308,vlan 92, port 13, encap 0xec05)
    *DHCP Socket Task: Apr 30 11:44:58.594: a4:c3:61:7a:1a:4f DHCP selecting relay 1 - control block settings:
                            dhcpServer: 172.24.13.251, dhcpNetmask: 0.0.0.0,
                            dhcpGateway: 0.0.0.0, dhcpRelay: 172.24.16.251  VLAN: 93
    *DHCP Socket Task: Apr 30 11:44:58.594: a4:c3:61:7a:1a:4f DHCP selected relay 1 - 172.24.13.251 (local address 172.24.16.251, gateway 172.24.16.254, VLAN 93, port 13)
    *DHCP Socket Task: Apr 30 11:44:58.594: a4:c3:61:7a:1a:4f DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Apr 30 11:44:58.594: a4:c3:61:7a:1a:4f DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
    *DHCP Socket Task: Apr 30 11:44:58.594: a4:c3:61:7a:1a:4f DHCP   xid: 0x7e549f4a (2119475018), secs: 8, flags: 0
    *DHCP Socket Task: Apr 30 11:44:58.594: a4:c3:61:7a:1a:4f DHCP   chaddr: a4:c3:61:7a:1a:4f
    *DHCP Socket Task: Apr 30 11:44:58.594: a4:c3:61:7a:1a:4f DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Apr 30 11:44:58.594: a4:c3:61:7a:1a:4f DHCP   siaddr: 0.0.0.0,  giaddr: 172.24.16.251
    *DHCP Socket Task: Apr 30 11:44:58.595: a4:c3:61:7a:1a:4f DHCP selecting relay 2 - control block settings:
                            dhcpServer: 172.24.13.251, dhcpNetmask: 0.0.0.0,
                            dhcpGateway: 0.0.0.0, dhcpRelay: 172.24.16.251  VLAN: 93
    *DHCP Socket Task: Apr 30 11:44:58.595: a4:c3:61:7a:1a:4f DHCP selected relay 2 - NONE
    *DHCP Proxy Task: Apr 30 11:44:58.595: a4:c3:61:7a:1a:4f DHCP received op BOOTREPLY (2) (len 572,vlan 0, port 0, encap 0x0)
    *DHCP Proxy Task: Apr 30 11:44:58.595: a4:c3:61:7a:1a:4f DHCP sending packet in EoIP tunnel to foreign 10.65.31.8 (len 346)
    *DHCP Proxy Task: Apr 30 11:44:58.595: a4:c3:61:7a:1a:4f DHCP transmitting DHCP OFFER (2)
    *DHCP Proxy Task: Apr 30 11:44:58.595: a4:c3:61:7a:1a:4f DHCP   op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
    *DHCP Proxy Task: Apr 30 11:44:58.595: a4:c3:61:7a:1a:4f DHCP   xid: 0x7e549f4a (2119475018), secs: 0, flags: 0
    *DHCP Proxy Task: Apr 30 11:44:58.595: a4:c3:61:7a:1a:4f DHCP   chaddr: a4:c3:61:7a:1a:4f
    *DHCP Proxy Task: Apr 30 11:44:58.595: a4:c3:61:7a:1a:4f DHCP   ciaddr: 0.0.0.0,  yiaddr: 172.24.16.102
    *DHCP Proxy Task: Apr 30 11:44:58.595: a4:c3:61:7a:1a:4f DHCP   siaddr: 0.0.0.0,  giaddr: 0.0.0.0
    *DHCP Proxy Task: Apr 30 11:44:58.595: a4:c3:61:7a:1a:4f DHCP   server id: 0.0.0.0  rcvd server id: 172.24.13.251
    *DHCP Socket Task: Apr 30 11:45:07.059: a4:c3:61:7a:1a:4f DHCP received op BOOTREQUEST (1) (len 308,vlan 92, port 13, encap 0xec05)
    *DHCP Socket Task: Apr 30 11:45:07.059: a4:c3:61:7a:1a:4f DHCP selecting relay 1 - control block settings:
                            dhcpServer: 172.24.13.251, dhcpNetmask: 0.0.0.0,

    Thanks Scott,  here you go...
    On Foreign:
    WLAN Identifier.................................. 2
    Profile Name..................................... BAI-Beta
    Network Name (SSID).............................. BAI-Beta
    Status........................................... Enabled
    MAC Filtering.................................... Disabled
    Broadcast SSID................................... Disabled
    AAA Policy Override.............................. Disabled
    Network Admission Control
      Client Profiling Status ....................... Disabled
       DHCP ......................................... Disabled
       HTTP ......................................... Disabled
      Radius-NAC State............................... Disabled
      SNMP-NAC State................................. Disabled
      Quarantine VLAN................................ 0
    Maximum number of Associated Clients............. 0
    Maximum number of Clients per AP Radio........... 200
    Number of Active Clients......................... 42
    Exclusionlist Timeout............................ 60 seconds
    Session Timeout.................................. 86400 seconds
    User Idle Timeout................................ 300 seconds
    --More-- or (q)uit
    User Idle Threshold.............................. 0 Bytes
    NAS-identifier................................... CHTWLC
    CHD per WLAN..................................... Enabled
    Webauth DHCP exclusion........................... Disabled
    Interface........................................ management
    Multicast Interface.............................. Not Configured
    WLAN IPv4 ACL.................................... unconfigured
    WLAN IPv6 ACL.................................... unconfigured
    mDNS Status...................................... Enabled
    mDNS Profile Name................................ default-mdns-profile
    DHCP Server...................................... Default
    DHCP Address Assignment Required................. Enabled
    Static IP client tunneling....................... Disabled
    PMIPv6 Mobility Type............................. none
    Quality of Service............................... Bronze
    Per-SSID Rate Limits............................. Upstream      Downstream
    Average Data Rate................................   0             0
    Average Realtime Data Rate.......................   0             0
    Burst Data Rate..................................   0             0
    Burst Realtime Data Rate.........................   0             0
    Per-Client Rate Limits........................... Upstream      Downstream
    Average Data Rate................................   0             0
    Average Realtime Data Rate.......................   0             0
    --More-- or (q)uit
    Burst Data Rate..................................   0             0
    Burst Realtime Data Rate.........................   0             0
    Scan Defer Priority.............................. 5,6
    Scan Defer Time.................................. 100 milliseconds
    WMM.............................................. Disabled
    WMM UAPSD Compliant Client Support............... Disabled
    Media Stream Multicast-direct.................... Disabled
    CCX - AironetIe Support.......................... Enabled
    CCX - Gratuitous ProbeResponse (GPR)............. Disabled
    CCX - Diagnostics Channel Capability............. Disabled
    Dot11-Phone Mode (7920).......................... Disabled
    Wired Protocol................................... None
    Passive Client Feature........................... Disabled
    Peer-to-Peer Blocking Action..................... Disabled
    Radio Policy..................................... All
    DTIM period for 802.11a radio.................... 1
    DTIM period for 802.11b radio.................... 1
    Radius Servers
       Authentication................................ 172.24.13.20 1812
       Accounting.................................... Disabled
       Dynamic Interface............................. Disabled
       Dynamic Interface Priority.................... wlan
    Local EAP Authentication......................... Disabled
    --More-- or (q)uit
    Security
       802.11 Authentication:........................ Open System
       FT Support.................................... Disabled
       Static WEP Keys............................... Disabled
       802.1X........................................ Disabled
       Wi-Fi Protected Access (WPA/WPA2)............. Enabled
          WPA (SSN IE)............................... Disabled
          WPA2 (RSN IE).............................. Enabled
             TKIP Cipher............................. Disabled
             AES Cipher.............................. Enabled
                                                                   Auth Key Management
             802.1x.................................. Enabled
             PSK..................................... Disabled
             CCKM.................................... Disabled
             FT-1X(802.11r).......................... Disabled
             FT-PSK(802.11r)......................... Disabled
             PMF-1X(802.11w)......................... Disabled
             PMF-PSK(802.11w)........................ Disabled
          FT Reassociation Timeout................... 20
          FT Over-The-DS mode........................ Enabled
          GTK Randomization.......................... Disabled
          SKC Cache Support.......................... Disabled
    --More-- or (q)uit
          CCKM TSF Tolerance......................... 1000
       WAPI.......................................... Disabled
       Wi-Fi Direct policy configured................ Disabled
       EAP-Passthrough............................... Disabled
       CKIP ......................................... Disabled
       Web Based Authentication...................... Disabled
       Web-Passthrough............................... Disabled
       Conditional Web Redirect...................... Disabled
       Splash-Page Web Redirect...................... Disabled
       Auto Anchor................................... Enabled
       FlexConnect Local Switching................... Disabled
       flexconnect Central Dhcp Flag................. Disabled
       flexconnect nat-pat Flag...................... Disabled
       flexconnect Dns Override Flag................. Disabled
       FlexConnect Vlan based Central Switching ..... Disabled
       FlexConnect Local Authentication.............. Disabled
       FlexConnect Learn IP Address.................. Enabled
       Client MFP.................................... Optional
       PMF........................................... Disabled
       PMF Association Comeback Time................. 1
       PMF SA Query RetryTimeout..................... 200
       Tkip MIC Countermeasure Hold-down Timer....... 60
    AVC Visibilty.................................... Disabled
    --More-- or (q)uit
    AVC Profile Name................................. None
    Flow Monitor Name................................ None
    Call Snooping.................................... Disabled
    Roamed Call Re-Anchor Policy..................... Disabled
    SIP CAC Fail Send-486-Busy Policy................ Enabled
    SIP CAC Fail Send Dis-Association Policy......... Disabled
    KTS based CAC Policy............................. Disabled
    Assisted Roaming Prediction Optimization......... Disabled
    802.11k Neighbor List............................ Disabled
    802.11k Neighbor List Dual Band.................. Disabled
    Band Select...................................... Disabled
    Load Balancing................................... Disabled
    Multicast Buffer................................. Disabled
     Mobility Anchor List
     WLAN ID     IP Address            Status
     2           172.24.13.251        Up
    802.11u........................................ Disabled
    MSAP Services.................................. Disabled
    On Anchor:
    WLAN Identifier.................................. 1
    Profile Name..................................... BAI-Beta
    Network Name (SSID).............................. BAI-Beta
    Status........................................... Enabled
    MAC Filtering.................................... Disabled
    Broadcast SSID................................... Disabled
    AAA Policy Override.............................. Disabled
    Network Admission Control
      Client Profiling Status ....................... Disabled
       DHCP ......................................... Disabled
       HTTP ......................................... Disabled
      Radius-NAC State............................... Disabled
      SNMP-NAC State................................. Disabled
      Quarantine VLAN................................ 0
    Maximum number of Associated Clients............. 0
    Maximum number of Clients per AP Radio........... 200
    Number of Active Clients......................... 48
    Exclusionlist Timeout............................ 60 seconds
    Session Timeout.................................. 86400 seconds
    User Idle Timeout................................ 300 seconds
    --More-- or (q)uit
    User Idle Threshold.............................. 0 Bytes
    NAS-identifier................................... CHADWLC01
    CHD per WLAN..................................... Enabled
    Webauth DHCP exclusion........................... Disabled
    Interface........................................ bai-beta
    Multicast Interface.............................. Not Configured
    WLAN IPv4 ACL.................................... unconfigured
    WLAN IPv6 ACL.................................... unconfigured
    mDNS Status...................................... Enabled
    mDNS Profile Name................................ default-mdns-profile
    DHCP Server...................................... Default
    DHCP Address Assignment Required................. Enabled
    Static IP client tunneling....................... Disabled
    PMIPv6 Mobility Type............................. none
    Quality of Service............................... Bronze
    Per-SSID Rate Limits............................. Upstream      Downstream
    Average Data Rate................................   0             0
    Average Realtime Data Rate.......................   0             0
    Burst Data Rate..................................   0             0
    Burst Realtime Data Rate.........................   0             0
    Per-Client Rate Limits........................... Upstream      Downstream
    Average Data Rate................................   0             0
    Average Realtime Data Rate.......................   0             0
    --More-- or (q)uit
    Burst Data Rate..................................   0             0
    Burst Realtime Data Rate.........................   0             0
    Scan Defer Priority.............................. 5,6
    Scan Defer Time.................................. 100 milliseconds
    WMM.............................................. Disabled
    WMM UAPSD Compliant Client Support............... Disabled
    Media Stream Multicast-direct.................... Disabled
    CCX - AironetIe Support.......................... Enabled
    CCX - Gratuitous ProbeResponse (GPR)............. Disabled
    CCX - Diagnostics Channel Capability............. Disabled
    Dot11-Phone Mode (7920).......................... Disabled
    Wired Protocol................................... None
    Passive Client Feature........................... Disabled
    Peer-to-Peer Blocking Action..................... Disabled
    Radio Policy..................................... All
    DTIM period for 802.11a radio.................... 1
    DTIM period for 802.11b radio.................... 1
    Radius Servers
       Authentication................................ 172.24.13.20 1812
       Accounting.................................... Disabled
       Dynamic Interface............................. Disabled
       Dynamic Interface Priority.................... wlan
    Local EAP Authentication......................... Disabled
    --More-- or (q)uit
    Security
       802.11 Authentication:........................ Open System
       FT Support.................................... Disabled
       Static WEP Keys............................... Disabled
       802.1X........................................ Disabled
       Wi-Fi Protected Access (WPA/WPA2)............. Enabled
          WPA (SSN IE)............................... Disabled
          WPA2 (RSN IE).............................. Enabled
             TKIP Cipher............................. Disabled
             AES Cipher.............................. Enabled
                                                                   Auth Key Management
             802.1x.................................. Enabled
             PSK..................................... Disabled
             CCKM.................................... Disabled
             FT-1X(802.11r).......................... Disabled
             FT-PSK(802.11r)......................... Disabled
             PMF-1X(802.11w)......................... Disabled
             PMF-PSK(802.11w)........................ Disabled
          FT Reassociation Timeout................... 20
          FT Over-The-DS mode........................ Enabled
          GTK Randomization.......................... Disabled
          SKC Cache Support.......................... Disabled
    --More-- or (q)uit
          CCKM TSF Tolerance......................... 1000
       WAPI.......................................... Disabled
       Wi-Fi Direct policy configured................ Disabled
       EAP-Passthrough............................... Disabled
       CKIP ......................................... Disabled
       Web Based Authentication...................... Disabled
       Web-Passthrough............................... Disabled
       Conditional Web Redirect...................... Disabled
       Splash-Page Web Redirect...................... Disabled
       Auto Anchor................................... Enabled
       FlexConnect Local Switching................... Disabled
       flexconnect Central Dhcp Flag................. Disabled
       flexconnect nat-pat Flag...................... Disabled
       flexconnect Dns Override Flag................. Disabled
       FlexConnect Vlan based Central Switching ..... Disabled
       FlexConnect Local Authentication.............. Disabled
       FlexConnect Learn IP Address.................. Enabled
       Client MFP.................................... Optional
       PMF........................................... Disabled
       PMF Association Comeback Time................. 1
       PMF SA Query RetryTimeout..................... 200
       Tkip MIC Countermeasure Hold-down Timer....... 60
    AVC Visibilty.................................... Disabled
    --More-- or (q)uit
    AVC Profile Name................................. None
    Flow Monitor Name................................ None
    Call Snooping.................................... Disabled
    Roamed Call Re-Anchor Policy..................... Disabled
    SIP CAC Fail Send-486-Busy Policy................ Enabled
    SIP CAC Fail Send Dis-Association Policy......... Disabled
    KTS based CAC Policy............................. Disabled
    Assisted Roaming Prediction Optimization......... Disabled
    802.11k Neighbor List............................ Disabled
    802.11k Neighbor List Dual Band.................. Disabled
    Band Select...................................... Disabled
    Load Balancing................................... Disabled
    Multicast Buffer................................. Disabled
     Mobility Anchor List
     WLAN ID     IP Address            Status
     1           172.24.13.251        Up
    802.11u........................................ Disabled
    MSAP Services.................................. Disabled

  • WLC 5508 LDAP Windows 2008 Server - auth based on AD groups

    hi NG,
    i'm trying to web-authenticate my Wifi user of an WLC 5508 against LDAP.
    Thereby i'm trying to autenticate all users within a GROUP, not an OU within the MS Active Directory based upon an Windows 2008 Server.
    I can authenticate against a user, witch is beeing put into an OU, according to examples based here: https://www.cisco.com/en/US/products/ps6366/prod_configuration_examples_list.html
    Checking based upon Users within OUs works fine.
    But i have not got all of those users wihin one single OU!
    Need help for following:    LDAP-Auth based on AD Groups:
    Using:
    MS-Domain:                          MY-DOMAIN.CH
    AD-GROUP:                          VPN-USERS
    AD-Structure:
    MY-DOMAIN.CH
    |
    GROUPS
            |
        Administrative Groups
                          |
                     VPN-USERS
                              (-> Member of this Groups (Wireless1, Wirless2, ...)
    Server Adress:               IP.IP.IP.IP
    Port:                                 389
    Enable Server Stats      YES
    Simple Bind                    Authenticated
    Bind Username              LDAP-USER
    Bind Password               supersecret
    Bind Passw. confirm      supersecret
    User Base DN:               ?-1-?
    User Attribute:                ?-2-?
    User Object Type:          Person
    Server Timeout               2
    What happens for instance, if i put a GROUP within a GROUP regarding the LDAP Authentication.
    I guess i have to authenticate against the "upper" GROUP, or do i have to create an entry on the WLC for every GROUP i'm questoning?
    Could some one provide my with an example, since i have not found documentation regarding this topic.
    Thank you.

    Hi,
    User Base DN : this is in case you want to restrict the search area. If you put "dc=mydomain,dc=CH", you will search your whole AD. Depending on the size, it can be slow ...
    Remember that the User Base DN is also used for the admin user.
    In conclusion, User Base DN should be the most restrictive path that leads to both the admins and the users you want to authenticate.
    Example :
    OU=Employees,OU=Humans,DC=Mydomain,DC=CH
    This would prevent to search in machines or any assets. This implies that the admin you bind with is an employee and you are only authenticating employees. You can have any number of OUs under employees, it doesn't matter
    Attribute : This is the object attribute that the WLC uses to compare with the user name. In general, you would go with sAMAccountName in AD. CN would be another common example for LDAP databases.
    If what you are looking for is to restrict access and only authenticate people who belong to a certain group. Then you need a radius server like ACS.
    That server will be able to make selections and check the "memberOf" attribute to make sure it is in a certain group.
    Nicolas
    ===
    Don't forget to rate answers that you find useful

Maybe you are looking for

  • Reg. CIN related excise capture for a SRM PO and goods receipt in R/3.

    Hello Gurus, We are on SRM 4.0 and have extended classic scenario. For Country India Roll out, we want to capture excise manually in R/3 once an SRM Goods confirmation from an SRM PO is posted to R/3 system as a goods receipt. We also tried manually

  • Safari quits unexpectedly for one user after Mavericks upgrade

    2.33 GHz Intel Core 2 Duo 15" Macbook Pro circa mid-2009 OS X 10.9.4 Safari 7.0.5 After the Mavericks upgrade Safari will always stay open for about 30 seconds before crashing and saying "Safari quit unexpectedly". Furthermore, unless I am looking in

  • Ipod won't do anything but restore

    Hello, I've had my ipod for about 6 months now working fine. All of the sudden when I put a new cd on it, it needs to restore. Fine... but since I had itunes up my ipod showed I had all those songs, but they were empty. I restored it again, and now i

  • Simple cfc mapping issue = I am a muppet

    Right, there's something blissfully simple that I'm just missing here, but I've had by C# hat on for weeks and now have had to come back to CF and I've gotten stuck on a simple issue. Yes, I've trawled Google and the search on here but I just can't s

  • Adding a line to the top of the mailing label

    Hi, I am a high school band teacher trying to send out letters to all of my students. I have the kids mailing addresses in Address book, as it doesn't appear I can do labels from Numbers or Pages. I used to do this with appleworks, but the school dis