Won't boot anymore but in safe mode

My laptop won't boot anymore. I get a gray screen with a prohibition sign. Here's what I found so far:
If I boot in the verbose mode it gets stuck on something like Looking for boot device.
I zapped the PRAM. Didn't help.
I can boot in safe mode.
I used Disk Utility to check the drive and permisions. Everything ok.
I can't boot from the original Snow Leopard DVD. I press C, the drive spins then stops.
I reinstalled Snow Leopard from the safe mode. Didn't help.
In safe mode Safari is crazy slow. Firefox runs full speed.
Any idea?

Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/.
Unless you can boot from your installer DVD there's nothing you can do to reinstall OS X, so I'm not sure how you did reinstall as you said.
Booting From An OS X Installer Disc
1. Insert OS X Installer Disc into the optical drive.
2. Restart the computer.
3. Immediately after the chime press and hold down the "C" key.
4. Release the key when the spinning gear below the dark gray Apple logo appears.
5. Wait for installer to finish loading.

Similar Messages

G770 won't boot normally or in safe mode... I suspect it has something to do with the boot optimizer

My Lenovo G770 will not boot in normal or safe mode. I usually escape out of the boot optimizer. Today I let it run and it went to the "starting windows" screen with a brief startup of the windows 7 animation...it freezes for a second, then a quick flash of the bsod, then to the "windows error recovery page" giving me the option of "starting windows normally" or "Launch Startup Repair (recommended)."
Starting Windows Normally eventually brings me back to the same place repeating what I just stated above paragraph.
When I launch the Startup Repair it "Cannot repair this computer automatically".
So I go to view advanced options for system recovery and support.
It brings me to 5 options:
Startup Repair (we already tried this above)
System Restore (unfortunately I didn't create any restore points)
System Image Recovery (unfortunately I haven't created an image to recover)
Windows Memory Diagnostic (no problems found-done several times)
Command Prompt (don't know what I can do here except for remove a bad/corrupted driver which may be the problem, but I don't know the driver name that is associated with the boot optimizer...can anyone tell me this?)
I've tried booting to safe mode in all of its incarnations and I can't even do that..it repeats the same things as stated above...windows 7 animation briefly starts then locks up, flash of bsod, then the windows error recovery page.
I've tried booting to last known good configuration (same thing occurs...brief startup of windows 7 animation, freeze, flash of bsod, then error recovery page.
The only thing that has given me any kind of result was "disabling system restart on system failure." When I do this, the BSOD doesn't flash briefly..it stays. and it gives me the error message page_fault_in_nonpaged_area.
I'm at a loss as to what to do. Not being able to boot into Safe Mode even is really frustrating. Any advice from anyone? can I remove the driver associated with the boot optimizer? If so, what is the name of the driver and where (directory) is it located?

How did you resolve the issue?
I have the exactly same issue.
When I go System Image Recovery -->Select System Image-->Advanced->I can open all the drives [:Local Drive(C , LENOVO(D, Local Disk(E, Boot(X-where i think executable booting is here]. It comes with an Open prompt asking me to enter File Name with a File type: Setup Information.
I don't know which setup information and where to find it on my Drives.
Anyone know how to fix?
I was trying to re-install Win 7 from DVD but it is not executing either.
Can I boot with USB Ubuntu and Install Win 7 from there??? but how?
Need help?

IMac G5 won't boot in normal and safe mode, but will from single-user mode

Hello everyone,
I'm quite new here, so I try to do my best if you have a question.
Yesterday, someone nearby me had a iMac G5 (Powermac8,1), and he sayd, that the computer sometimes will boot, sometimes not.
I did test it, I thought it was running fine, but when I played some music in iTunes, it was stuck on 9 seconds, and crashed (with a kernel panic). The guy also sayd, that there was nothing important on the computer, so a clean install was fine.
Now, the problem is, that it will not boot in normal mode (without anything pressed on boot), also it won't in safe mode (shift-boot), but it will, when I enter single-user mode, mount the hard drive and exit from single-user mode so it will go futher on booting. Sometimes it will not, and immediately gives you a kernel panic in single-user mode, but it will 90 percent of the time.
Then you've got another problem: when it's running in the normal desktop from single-user mode, it'll be stuck after some time again. If I look into the Kernel Panic file created, most times it's because of Spotlight indexing, so I disabled that.
He also gave me the disks (Apple Hardware Test and Extra Applications, and iMac G5 Mac OS X Install Disks 1-3) that came with the Mac. He sayd that I could use them, but I think he didn't test out the SuperDrive, because when I insert a disk, it will try to read, but it will make 2 same sounds, and quits after 10 tries, when it will spit the cd out. Also normal (audio) disks.
Also, I must hurry with the commands for mounting and exiting in single-user mode, or it will just not boot.
In all cases, after 30-45 seconds from pressing the power button, the fan will start blowing at full speed, and it will stop after the exit command in Single-user mode. That's weird.
I can't do anything with the SuperDrive, I can't normally boot in Mac OS X except for Single-user mode (but I don't think he would like to do that every time the computer boots up), and I have very limited time when Mac OS X arrived on the desktop.
When booting in Verbose mode, it will be stuck on this:
AppleSMU::PMU vers = 0x000d004c, SPU vers = 0x15, SDB vers = 0x01,
(and sometimes ends with a kernel crash by fsck_hfs)
Things I've tried (without any success):
- /sbin/fsck -fy (in single-user mode)
- Disabling Spotlight and mds
If you want some more information, feel free to ask!
Greetings
-MrYoranimo
PS: My main language is Dutch, so my English can be bad at some points.

Thank you for your support! This reply is a little bit late, because I was to the camping this weekend.
The only thing I sure do know, is that the iMac has a bad SuperDrive. That's one problem, but I don't really wanna use it, and you fix everything by Single-user mode and when I get to the desktop to test things and change stuff in the Preference Panes.
What also came to my mind was that there also is a problem with the videocard (driver), because sometimes when I boot into Single-user mode, I can see some white pixels which aren't supposed to be there. And when booting from SUM you can see that some of the colors are different and there are weird patterns on the screen.
I also tried to setup a NetBoot server on this computer (MacBook Mid 2010) with just Lion 10.7.4 on it, but I'm not that expert and I didn't really find the good posts on the Internet, although I tried it with the Server applications and both Server applications and DeployStudio. But I didn't succeed.
I don't really like buying a new FireWire hard disk or external FireWire dvd reader/writer, except if it has USB support, because my MacBook doesn't support FireWire, and I really wanna make use of it then.
If I know more or have fixed it, I will surely post again here with what I did to fix it (if no one else has posted here already ).

My Macbook Pro won't boot up, only in safe mode!

Help, my macbook pro won't restart, only in safe mode! and it seems that safe mode has plenty of implications for use. my usb memory stick doesn't seem to be recognized while in safe mode. I was doing a cleanup on mackeeper just after I downloaded a trial version of microsoft office mac. The trial wouldn't work properly so I deleted it and decided to do a cleanup with mackeeper. than the mac froze while mackeeper was doing it's cleanup and the screen flashed black a few times. Ever since it won't boot up unless I use safe mode. Also, I downloaded the most recent updates while in safe mode but it doesn't seem to be recognizing that I already downloaded them because software update is still telling me that I have 6 updates. So I am horribly confused at this point. Please help, I need this laptop to do report cards (it's a good thing I got an extension). thanks

Please read this whole message before doing anything.
This procedure is a diagnostic test. It won’t solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
Third-party system modifications are a common cause of usability problems. By a “system modification,” I mean software that affects the operation of other software — potentially for the worse. The following procedure will help identify which such modifications you've installed. Don’t be alarmed by the complexity of these instructions — they’re easy to carry out and won’t change anything on your Mac.
These steps are to be taken while booted in safe mode.
Below are instructions to enter some UNIX shell commands. The commands are harmless, but they must be entered exactly as given in order to work. If you have doubts about the safety of the procedure suggested here, search this site for other discussions in which it’s been followed without any report of ill effects.
The commands may line-wrap or scroll in your browser, but each one is really just a single line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, and you can then either copy or drag it. The headings “Step 1” and so on are not part of the commands.
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
When you launch Terminal, a text window will open with a line already in it, ending either in a dollar sign (“$”) or a percent sign (“%”). If you get the percent sign, enter “sh” and press return. You should then get a new line ending in a dollar sign.
Step 1
Triple-click the line of text below to select it. Copy the selected text to the Clipboard (command-C). Then click anywhere in the Terminal window and paste (command-V).
find /Sy*/L*/Ex* -type f -name Info.plist -exec sh -c '/usr/libexec/PlistBuddy -c "Print :CFBundleIdentifier" "$1" 2> /dev/null | egrep -qv "apple|Accusys|ArcMSR|ATTO|CalDigit|HighPoint|hp-fax|JMicron|print|SoftRAID|stex" && echo ${1%*.kext/*}.kext' {} {} \;
Post the lines of output (if any) that appear below what you just entered (the text, please, not a screenshot.) You can omit the final line ending in “$”.
Step 2
Repeat with this line:
ls -1A /e*/mach* {,/}L*/{Ad,Compon,Ex,Fram,In,Keyb,La,Mail/Bu,P*P,Priv,Qu,Scripti,Servi,Spo,Sta}* L*/Fonts 2> /dev/null
Important: If you formerly synchronized with a MobileMe account, your me.com email address may appear in the output of the above command. If so, anonymize it before posting.
Step 3
osascript -e 'tell application "System Events" to get name of every login item' 2> /dev/null
Remember, these steps are all copy-and-paste — no typing. Also remember to post the output.
You can then quit Terminal.

Mac won't boot properly unless in safe mode

Recently I updated my MacBook Pro to OS X Yosemite. I then started the process of the data encryption.
I don't know what happened, but maybe the encryption failed, because now every time I turn my mac on, it won't boot properly unless it's in safe mode.
Either it will have a black screen with a visible cursor, or just the desktop with no dock or the bar along the top and no icons, or it does boot up properly, but works extremely slowly. Like if I was to press the apple symbol on the top-right of the screen, it would take 5 minutes to actually open it. Nothing works properly.
And so I opened up my system preferences, and discovered that the Encryption is stuck on half-finished. But I can't stop it. If I try to turn encryption off it says I have to wait till it's finished. But it never does, the progress bar never moves.
If I open System Preferences while in Safe Mode, the progress bar for Encryption is grey, and underneath it says "connect to power to continue encryption". But it IS connected to power.
Have I stuffed my Mac? Is there a way to get it working again?

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
Don't be put off by the complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents to me or anyone else.
You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
You may not be able to understand the script yourself. But variations of the script have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message.
Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
4. Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
5. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
7. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts SerialATA 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports ' com.clark.\* \*dropbox \*genieo\* \*GoogleDr\* \*k.AutoCAD\* \*k.Maya\* vidinst\* ' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 "` route -n get default|awk '/e:/{print $2}' `" 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB ' com.adobe.AAM.Updater-1.0 com.adobe.AAM.Updater-1.0 com.adobe.AdobeCreativeCloud com.adobe.CS4ServiceManager com.adobe.CS5ServiceManager com.adobe.fpsaud com.adobe.SwitchBoard com.adobe.SwitchBoard com.apple.aelwriter com.apple.AirPortBaseStationAgent com.apple.FolderActions.enabled com.apple.installer.osmessagetracing com.apple.mrt.uiagent com.apple.ReportCrash.Self com.apple.rpmuxd com.apple.SafariNotificationAgent com.apple.usbmuxd com.citrixonline.GoToMeeting.G2MUpdate com.google.keystone.agent com.google.keystone.daemon com.microsoft.office.licensing.helper com.oracle.java.Helper-Tool com.oracle.java.JavaUpdateHelper com.oracle.java.JavaUpdateHelper org.macosforge.xquartz.privileged_startx org.macosforge.xquartz.privileged_startx org.macosforge.xquartz.startx ' ' 879294308 4071182229 461455494 3627668074 1083382502 1274181950 1855907737 2758863019 1848501757 464843899 3694147963 1233118628 2456546649 2806998573 2778718105 2636415542 842973933 2051385900 3301885676 891055588 998894468 695903914 1443423563 4136085286 523110921 2883943871 3873345487 ' 51 5120 files );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^$[0-9]+$ /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n-\t%s\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' s/[0-9A-Za-z._]+@[0-9A-Za-z.]+\.[0-9A-Za-z]{2,4}/EMAIL/g;/faceb/s/(at\.)[^.]+/\1NAME/g;/\/Shared/!s/(\/Users\/)[^ /]+/\1USER/g;s/[-0-9A-Fa-f]{22,}/UUID/g;' ' s/^ +//;/de: S|[nst]:/p;' ' {sub(/^ +/,"")};/er:/;/y:/&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: (E[^m]|[^EO])|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Genesy|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { if(n<10) print "com.apple.";} ' ' { sub(/ :/,"");print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:[^:]+//p ' '/^root$/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/ { n++;print;} END { if(n<1100) print "/System/";} ' '/^\/usr\/lib\/.+dylib$/p' ' /Temp|emac/{next};/(etc|Preferences|Launch[AD].+)\// { sub(".(/private)?","");n++;print;} END { split("'"${p[41]}"'",b);split("'"${p[42]}"'",c);for(i in b) print b[i]".plist\t"c[i];if(n<500) print "Launch";} ' ' /\/(Contents\/.+\/Contents|Frameworks)\/|\.wdgt\/.+\.([bw]|plu)/d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| |\n","\\|\\|kMDItem'${p[35]}'=");sub("^...."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[43]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/{next};/%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";p="uniq -c|sed -E '"'s/ +\$[0-9]+\$\$.+\$/\\\2 x\\\1/;s/x1$//'"'";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]$1|p;b=b$1;} END { close(p);if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"cksum "F|getline C;split(C, A);C="checksum "A[1];"file -b "F|getline T;if(T!~/^(AS.+ (En.+ )?text(, with v.+)?$|(Bo|PO).+ sh.+ text ex|XM)/) F=F" ("T", "C")";else F=F" ("C")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n ...and %s more line(s)\n",l-L);} ' ' s/^ ?n...://p;s/^ ?p...:/-'$'\t''/p;' 's/0/Off/p' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / / { print "'"${p[28]}"'";exit;};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/$L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9|"sort|uniq";} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ /V/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' ' /^find: /d;p;' "`S0 44 45`" ' BEGIN{FS="= "} /Path/{print $2} ' ' /^ *$/d;s/^ */ /;' ' s/^.+ |\(.+$$//g;p ' '/\.(appex|pluginkit)\/Contents\/Info\.plist$/p' ' /2/{print "WARN"};/4/{print "CRITICAL"};' ' /EVHF|MACR|^s/d;s/^.+: //p;' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps crontab iotop top pkgutil 'PlistBuddy 2>&1 -c "Print' whoami cksum kextstat launchctl smcDiagnose sysctl\ -n defaults\ read stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' pluginkit scutil dtrace profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil lsof test osascript\ -e );c2=(com.apple.loginwindow\ LoginHook '" /L*/P*/loginw*' "'tell app \"System Events\" to get properties of login items'|tr , \\\n" 'L*/Ca*/com.ap*.Saf*/E*/* -d 1 -name In*t -exec '"${c1[14]}"' :CFBundleDisplayName" {} \;|sort|uniq' '~ $TMPDIR.. $ -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' :${p[35]}\" :Label\" '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$(RefProc): \$Message' -k Sender Req 'fsev|kern|launchd' -k RefProc Rne 'Aq|WebK' -k Message Rne 'Goog|ksadm|probe|Roame|SMC:|smcD|sserti|suhel| VALI|ver-r|xpma' -k Message Req 'abn|bad |Beac|caug|corru|dead[^bl]|FAIL|fail|GPU |hfs: Ru|inval|jnl:|last value [1-9]|NVDA$|pagin|proc: t|Roamed|rror|SL|TCON|Throttli|tim(ed? ?|ing )o|WARN' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cght] ! -name .?\* ! -name \*ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true $ -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '/S*/*/Ca*/*xpc* >&- ||echo No' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,Ex}* {/,}L*/{A*d,Ca*/*/Ex,Co{mpon,reM},Ex,In{p,ter},iTu*/*P,Keyb,Mail/B,Pr*P,Qu*T,Scripti,Sec,Servi,Spo,Widg}* -path \\*s/Resources -prune -o -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,{[lp],sy}*.conf,mach_i*/*,pam.d/*,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t {/S*/,/,}L*/Lau*/*t .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers\ "${p[N5]}" -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' '+c0 -i4TCP:0-1023' com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' '-app Safari WebKitDNSPrefetchingEnabled' "+c0 -l|awk '{print(\$1,\$3)}'|sort|uniq -c|sort -n|tail -1|awk '{print(\$2,\$3,\$1)}'" -m 'L*/{Con*/*/Data/L*/,}Pref* -type f -size 0c -name *.plist.???????|wc -l' kern.memorystatus_vm_pressure_level '3>&1 >&- 2>&3' " -F '\$Time \$Message' -k Sender kernel -k Message CSeq 'n Cause: -' " );N1=${#c2[@]};for j in {0..9};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents XPC\ cache Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls Prefetching SATA Descriptors App\ extensions Lockfiles Memory\ pressure SMC Shutdowns );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};A'$((7+i))'() { v=` eval sudo "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};';done;A9(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0() { [[ "$v" ]]&&sed -E "$s"<<<"$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v"|sed -E "$s";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "${s[63]}"<<<"$v"`&&C1 1 $1;};for i in 1 2 7 8;do for j in 0 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;D20 0 $((N1+1)) 2;D10 0 $N1 1;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;D13 0 $((N1+9)) 59 50;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;B1&&D73 19 53 67 55;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 54 12 56;D23 5 14 12 14;D22 6 36 13 15;D22 20 52 66 54;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D82 35 49 61 51;D82 11 17 17 20;for i in 0 1;do D82 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A8 18 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;B3 4 0 65;A3 14 6 32 0;B4 0 16 11;A1 26 50 64;B7 16;C3 52;D13 24 24 32 31;D13 25 37 32 33;A2 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D73 21 0 32 19;D73 10 42 32 40;D82 29 35 46 39;};D23 14 1 62 42;D12 34 43 53 44;D12 22 20 32 25;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 21 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 33 34 42 37;B1&&D83 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 10 42 32 41;D13 37 2 48 43;D13 4 5 32 1;D13 4 3 60 5;D12 21 48 49 49;B3 4 22 57;A1 21 46 56;B7 22;B3 0 0 58;C3 47;D22 4 4 50 0;D12 4 51 32 53;D23 22 9 37 7;A9;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
8. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report what happened. No harm will be done.
12. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
14. This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

My computer won't boot up even in safe mode

I have a 2010 Imac that has been a great computer. Yesterday, I tried to turn it back on and it wouldn't boot up. The white screen with the apple came on, the little wheel spun and then it went directly to a dark gray screen that I could see the mouse present.
I looked on line the directions to start it up in safe mode, but that didnt work either.
Help. I hope it is fixable.

hi i would recomend going into the the intel imac section this section is for older imacs you would be able to get an answer to your question faster. just copy and past what you said and select imac intel instead

Macbook won't boot, Blue Screen in Safe Mode

Having a couple of issues at the moment. To start off, woke my MacBook from sleep mode and found the screen had shimmering edges, the screen was also displaced (part of the left of the screen was showing on the right. Decided to reboot to solve the issue, when I tried this, got past the Apple logo and wheel, then got a blue screen. Now when I boot, I just get a white screen Tried booting in safe mode but ended up with a blue screen with streaks.
On top of that when I went into support, my macbook isn't listed under my products and when I tried to enter it in, it said it was under a different account (I did get it through a college course but It was definitely registered under my name and with my account).
Can anyone shed some light on this, or have any suggestions?

Actually, just get a blue screen when trying to start up normally

Mac Pro won't boot up unless in Safe Mode

When I try to boot my Mac Pro the fans start revolving very quickly and it loads to the spinning wheel/apple logo screen. I can get it to start up in Safe Mode, and 9 times out of 10 if I restart the computer from Safe Mode I can get everything to load properly UNTIL I try to use any of the programs at which point each program freezes as I attempt to use it. Then I have to shut the computer down using the power button rather than restarting traditionally, and then I'm at square one again. This problem has gotten progressively worse, I used to be able to restart from Safe Mode and everything would work afterward.
Any thoughts?

Yes, as Hatter said, I think it's time for DiskWarrior. It is the best at directory repairs. It rebuilds then actually replaces your old directory. I feel every Mac owner should have a copy.
Make sure you get the disk, not the download, so you can boot up on it to run repairs if needed. You can also install it on another drive and run it from there to repair this one. DW works faster that way.
I use DW once a month to try and catch errors in my system from getting too far out of hand.
 DALE
p.s. Here's a rewiew of DiskWarrior 4.

My 2009 iMac gets stuck on the grey Apple logo when booting up. It boots correctly when in safe mode. I have tried erasing the HD and re-installing from a USB installer. It says the install is complete, but after restarting it gets stuck on the Apple log

My late 2009 27" iMac gets stuck on the grey Apple logo when booting up. It boots correctly when in safe mode. I have tried erasing the HD and re-installing from a USB installer. It says the install is complete, but after restarting it gets stuck on the Apple logo again. This could possibly be an HD failure, but then why does Safe Mode still work and the USB install not work? Any ideas?

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
Don't be put off merely by the seeming complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. All it does is to collect information about the state of the computer. That information goes nowhere unless you choose to share it. However, you should be cautious about running any kind of program (not just a shell script) at the behest of a stranger. If you have doubts, search this site for other discussions in which this procedure has been followed without any report of ill effects. If you can't satisfy yourself that the instructions are safe, don't follow them. Ask for other options.
Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
4. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
5. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
6. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts 51 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports 'com.autodesk.AutoCad com.evenflow.dropbox com.google.GoogleDrive' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 ` route -n get default|awk '/e:/{print $2}' ` 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^$[0-9]+$ /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n\t(%s)\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' /^ *$|CSConfigDot/d;s/^ */ /;s/[-0-9A-Fa-f]{22,}/UUID/g;s/(ochat)\.[^.]+(\..+)/\1\2/;/Shared/!s/\/Users\/[^/]+/~/g ' ' s/^ +//;5p;6p;8p;12p;' ' {sub(/^ +/,"")};NR==6;NR==13&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: [^EO]|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { if(n<200) print "com.apple.";} ' ' $3~/[0-9]:[0-9]{2}$/ { gsub(/:[0-9:a-f]{14}/,"");} { print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:[^:]+//p ' '/root/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/ { n++;print;} END { if(n<1000) print "/System/";} ' '/^\/usr\/lib\/.+dylib$/p' ' /Temp|emac/d;/(etc|Preferences)\//s/^\.\/[^/]+//p;' ' /\/(Contents\/.+\/Contents|Frameworks)\/|\.wdgt\/.+\.([bw]|plu)/d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| ","||kMDItem'${p[35]}'=");sub("^.."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[9]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/ { next;} /%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]" "$1;b=b$1;} END { if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"file -b "F|getline T;if(T!~/^(AS.+ (En.+ )?text$|POSIX sh.+ text ex)/) F=F" ("T")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n ...and %s more line(s)\n",l-L);} ' ' /^ +[NP].+ =/h;/^( +D.+[{]|[}])/{ g;s/.+= //p;};' ' /^ +B/{ s/.+= |(-[0-9]+)?\.s.+//g;p;} ' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / /{$0="'"${p[28]}"'"};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/$L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9;} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' 's/0/Off/p' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps sudo\ crontab sudo\ iotop top pkgutil PlistBuddy whoami cksum kextstat launchctl sudo\ launchctl crontab 'sudo defaults read' stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' defaults\ read scutil sudo\ dtrace sudo\ profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil sudo\ lsof test );c2=(com.apple.loginwindow\ LoginHook '-c Print /L*/P*/loginw*' '-c Print L*/P*/*loginit*' '-c Print L*/Saf*/*/E*.plist' '~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' '-c Print\ :'${p[35]}' 2>&1' '-c Print\ :Label 2>&1|head -1' '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message Req 'Beac|caug|dead[^bl]|FAIL|fail|GPU |hfs: Ru|inval|jnl:|last value [1-9]|n Cause: -|NVDA$|pagin|proc: t|Roamed|rror|ssert|Thrott|tim(ed? ?|ing )o|WARN' -k Message Rne 'Goog|ksadm|SMC:' -o -k Sender fseventsd -k Message Req 'SL' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cgh] ! -name *ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true $ -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '-L {/{S*/,},}L*/Lau* -type f' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,E}* {/,}L*/{A*d,Ca*/*/Ex,Compon,Ex,In,iTu,Keyb,Mail/B,P*P,Qu*T,Scripti,Sec,Servi,Spo,Widg}* -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,{[lp],sy}*.conf,pam.d,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers\ "${p[N5]}" -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' -i4TCP:0-1023 com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' '-app Safari WebKitDNSPrefetchingEnabled' );N1=${#c2[@]};for j in {0..8};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents launchd Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls Prefetching );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};';done;A7(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0(){ [[ "$v" ]]&&echo "$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "$s"<<<"$v"`&&C1 1 $1;};for i in 1 2;do for j in 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;A2 0 $((N1+1)) 2;C0;A1 0 $N1 1;C0;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 14 12 14;D22 6 36 13 15;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D22 11 17 17 20;for i in 0 1;do D22 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A2 19 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;A2 4 20 21;B7 6;B2 9;A4 14 7 52 9;B2 10;B6 9 10 4;C3 25;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;D13 24 24 32 31;D13 25 37 32 33;A1 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D13 21 0 32 19;D13 10 42 32 40;D22 29 35 46 39;};D23 14 1 48 42;D12 34 43 53 44;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 26 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 33 34 42 37;B1&&D23 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 20 42 32 41;D13 14 2 48 43;D13 4 5 32 1;D22 4 4 50 0;D13 14 3 49 5;D12 26 48 59 49;B3 4 22 57;A1 26 46 56;B7 22;B3 0 0 58;C3 47;D23 22 9 37 7;A7;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
7. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
8. If you see an error message in the Terminal window such as "syntax error," enter
exec bash
and press return. Then paste the script again.
9. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
10. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report the results. No harm will be done.
11. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with "Model Identifier." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
12. When you post the results, you might see the message, "You have included content in your post that is not permitted." It means that the forum software has misidentified something in the post as a violation of the rules. If that happens, please post the test results on Pastebin, then post a link here to the page you created.
Note: This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

G5 dual 2ghz. Been unplugged for a while. Powers up but no video or power to usb keyboard. Boots up fine in safe mode, restart into normal mode ok. After shutdown, back to same issue. What's happening?

G5 dual 2ghz. Been unplugged for a while. Powers up but no video or power to usb keyboard. Boots up fine in safe mode, restart into normal mode ok. After shutdown, back to same issue. What's happening?

I keep seeing people ask and the advice to replace if it has been unplugged, but really have nothing to confirm that from my experiences.
My experience is that a weak or dead battery can cause much more than date and time issues.
I have seen it time and time again.
Deal with used machines and you will quickly learn....
I'll give no "recipe" or set list of symptoms, but the range of irregularities that can occur make it a quick and easy first line of troubleshooting, especially when the machine has been off the mains for a few months.
Why fight mysterious maladies and troubleshoot with the knowledge that the PRAM battery is beyond it's useful life.
Maybe they recharge?
Not likely. They are chemically nasty, disposable, one way discharge batteries.
They aren't Lithium-ion batteries

Mac mini won't boot anymore

My Mac mini won't boot anymore. It's been running fine for months.
It's running Leopard Server 10.5.2 Build 9C31
It starts to boot, I get the first spinning gear with the gray screen, then the blue desktop blinks, then a second spinning gear on a gray screen and it appears to hang (the gear stops spinning).
I booted off the install DVD, ran disk utility, repaired the HD, repaired the permissions: the behavior is the same.
Safe mode doesn't work (same hang as above).
Single user mode does work.
I can connect to it via Server Admin while it appears hung.
The last few lines of the system log are:
May 15 18:38:58 server emond[67]: SetUpLogs: uid = 0 gid = 0
May 15 18:38:58 server emond[67]: SetUpLogs: opening /Library/Logs/EventMonitor/EventMonitor.error.log
May 15 18:38:59 server kextd[23]: writing kernel link data to /var/run/mach.sym
May 15 18:39:09 server KernelEventAgent[59]: tid 00000000 received unknown event (12)
May 15 18:39:20 server kernel[0]: display: Not usable
May 15 18:39:20 server com.apple.KerberosAutoConfig[126]: Kerberos configuration is up to date
May 15 18:39:20 server com.apple.ATSServer[125]: FODBCheck: New annex file created
May 15 18:39:21 server ARDAgent [130]: ******ARDAgent Launched******
May 15 18:39:21 server com.apple.KerberosAutoConfig[132]: Kerberos configuration is up to date
May 15 18:39:22 server ARDAgent [130]: call logout from LoginLogoutProxyCallBackFunction
May 15 18:39:22 server com.apple.launchd[1] (com.apple.RemoteDesktop.agent): Throttling respawn: Will start in 9 seconds
May 15 18:39:24 server loginwindow[58]: Login Window Started Security Agent
May 15 18:39:29 server servermgrd[53]: servermgr_calendar: created default calendar virtual host
May 15 18:39:31 server ARDAgent [146]: ******ARDAgent Launched******
May 15 18:39:32 server ARDAgent [146]: ******ARDAgent Ready******
May 15 18:39:33 server mdworker[109]: (Error) SyncInfo: Boot-cache avoidance timed out!
May 15 18:39:54 server Python[47]: CGImageSourceCreateWithData data parameter is nil
May 15 18:39:54 server com.apple.wikid[47]: Thu May 15 18:39:54 server.jeff.carpenter.name Python[47] <Error>: CGImageSourceCreateWithData data parameter is nil\n
May 15 18:39:56 server kernel[0]: AppleYukon2 - bad packet received. length: 1440, packet status bits: MII error
May 15 18:39:56 server kernel[0]: AppleYukon2: 00000000,00000001 sk98osx sky2 - - sk98osx_sky2::replaceOrCopyPacket tried N times
May 15 18:49:54 server kernel[0]: serialnumberd 194 FSWRITEDATA SBF /dev/dtracehelper 13 (seatbelt)
May 15 18:49:54 server kernel[0]: serialnumberd 194 FSREADDATA SBF /dev/autofs_nowait 13 (seatbelt)
May 15 18:49:54 server kernel[0]: serialnumberd 194 FSREADDATA SBF /usr/sbin 13 (seatbelt)
May 15 18:55:12 server kernel[0]: AppleYukon2 - bad packet received. length: 23, packet status bits: MII error
Any ideas?

Yes, it's been running Server since I purchased it.
I doubt the serial number is in use elsewhere: I purchased the 10-user version at a retail store in a sealed package and I've only installed it once.

Re: Satellite C850 won't boot anymore - broken HDD

Hello Folks,
I bought a *Toshiba Satellite C850 - 1F2* with *+Windows 8+*.
After installing, upgrading to *+Windows 8.1+* and setting up everything, the whole machine worked pretty fine.
BUT since yesterday the laptop won't boot anymore!
When I turn it on, the HDD makes click and click and the system tries to boot from DVD, from USB, from HDD, from IPV4, from IPV6 and then it says, that there is no bootable device.
Unfortunately I wanted to make the +Windows 8 Restoration-/Rescue-DVDs+ this weekend!
Huh!!!
Well, I still have an *+original Windows-7-DVD and license+*, which would be good as well (I used it the last years).
*YET*, I cannot install *+Windows 7+*.
It says something like that, that +this system is not available for Secure Boot+.
I read about "Secure Boot".
So I pressed F2, turned the laptop on and could with this reach the BIOS.
It is a *+InsydeH20 Rev. 3.7+*.
*BUT*, when I go to "Boot Mode" I can only see, that this option is greyed and I cannot change from +UEFI Boot+ to +CSM Boot+.
Even the change of the HDD made no difference.
I put in my old HDD with Windows 7 installed (wich works in the other laptop), but the system won't boot, for it is +not suitable for Secure Boot+.
*So, WHAT NOW?*
I mean, it cannot really be the Toshiba politics, that you need to throw away your laptop, if the HDD breaks, can it?
For I didn't create the Rescue-DVD, I have just my Windows 7 DVD and another HDD with installed Windows 7.
Do I need to buy another Windows 8 licence and another HDD, to install Windows 8 (suitable for Secure Boot) again?
Would it even work like that?
Or is there any chance to upgrade the BIOS, for that I can then change from UEFI Boot to CSM Boot?
Or is there any other chance, to use my other HDD with Windows 7, or at least a new clean HDD, on wich I then can install my Windows 7 OS?
I hope, that someone can give me any good advice, what to do now ... without throwing the Toshiba laptop away ;)
Thanks in advance!

If the HDD died, in needs to be replaced.
If notebook is still covered by warranty, the HDD will be replaced free of charge. If warranty isnt valid, you will need to pay for the new HDD.
I think this understandable.
_Now some facts about the Recovery disk._
If you did not create a recovery disk in the past, you could order the recovery medium on this page: http://backupmedia.toshiba.eu/landing.aspx
The recovery disk would install the Toshiba image and would set the notebook back to the same state like at the first day of purchase.
_Regarding the Win 7 installation:_
Usually to install the non UEFI capable system, the secure boot needs to be disabled and boot mode needs to be set to CSM mode.
If this isnt possible you should update the BIOS but to do that you need an running Windows system (Win 8).

Btrfs: System won't boot anymore after unclean shutdown

Hi,
I have a problem with my ArchLinux (kernel 3.19.2-1-ARCH).
I have my root partition as BTRFS and no /boot partition.
After an unclean shutdown the system won't boot anymore.
GRUB loads the kernel and the kernel starts but it hangs saying: Mounted /dev/sda3 on real root.
Then, I have to start a Live CD and do:
btrfsck /dev/sda3
After that the system boots correctly.
I've tried adding fsck to the HOOKS in the mkinitcpio.conf file and in fact it tries to fsck the filesystem (but with BTRFS, fsck.btrfs doesn't work...)
What can I do?
Thanks

I'm also having this problem. I tried booting up the netinstall image to debug it, but I can't mount my btrfs volume from there either: mount just hangs. After a while, the kernel goes:
[...] INFO: task mount:612 blocked for more than 120 seconds.
[...] Not tainted 3.19.2-1-ARCH #1
[...] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[...] INFO: task btrfs-transacti:636 blocked for more than 120 seconds.
[...] Not tainted 3.19.2-1-ARCH #1
[...] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
From this post I guessed that I might just need to wait so that I could defrag the volume once it was mounted, but it's been hanging for over 15min now (the message above continues to come up periodically).
Like the OP in the thread I linked to above, my btrfs volume is inside an LVM volume (which is on dm-crypt). Don't know whether that's relevant.
Output of btrfs-check:
Checking filesystem on /dev/pixie/btrfs
UUID: e04cc661-e31a-4dbf-870d-664bc913e34a
found 76855677062 bytes used err is 1
total csum bytes: 72928436
total tree bytes: 2092515328
total fs tree bytes: 1888452608
total extent tree bytes: 104644608
btree space waste bytes: 357251032
file data blocks allocated: 181197139968
referenced 109440282624
btrfs-progs v3.19
dmesg output:
[ 36.824998] Btrfs loaded
[ 36.826713] BTRFS: device fsid e04cc661-e31a-4dbf-870d-664bc913e34a devid 1 transid 98618 /dev/dm-3
[ 46.219014] BTRFS info (device dm-3): disk space caching is enabled
[ 46.259830] BTRFS: detected SSD devices, enabling SSD mode
[ 240.333313] INFO: task mount:539 blocked for more than 120 seconds.
[ 240.335542] Not tainted 3.19.2-1-ARCH #1
[ 240.337795] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.340263] mount D ffff8800cf2837f8 0 539 453 0x00000000
[ 240.340277] ffff8800cf2837f8 ffff8800cf2331b0 0000000000013f00 ffff8800cf283fd8
[ 240.340286] 0000000000013f00 ffffffff81818540 ffff8800cf2331b0 ffff8802094f67a8
[ 240.340291] 0000000000000004 ffff8800cf283758 ffffffffa0a2fc91 ffff8802094f67a8
[ 240.340298] Call Trace:
[ 240.340335] [<ffffffffa0a2fc91>] ? set_extent_buffer_dirty+0x71/0xc0 [btrfs]
[ 240.340357] [<ffffffffa0a05796>] ? btrfs_buffer_uptodate+0x56/0x80 [btrfs]
[ 240.340366] [<ffffffff8155e999>] schedule+0x29/0x70
[ 240.340389] [<ffffffffa0a47745>] btrfs_tree_lock+0x65/0x200 [btrfs]
[ 240.340396] [<ffffffff810b4380>] ? wait_woken+0x90/0x90
[ 240.340410] [<ffffffffa09e5cd9>] btrfs_search_slot+0x799/0xaa0 [btrfs]
[ 240.340425] [<ffffffffa09e79f5>] btrfs_insert_empty_items+0x75/0xd0 [btrfs]
[ 240.340446] [<ffffffffa0a47a37>] btrfs_insert_orphan_item+0x67/0xa0 [btrfs]
[ 240.340465] [<ffffffffa0a4a12e>] insert_orphan_item+0x5e/0x90 [btrfs]
[ 240.340482] [<ffffffffa0a4c531>] replay_one_buffer+0x361/0x380 [btrfs]
[ 240.340504] [<ffffffffa0a2f244>] ? alloc_extent_buffer+0x34/0x370 [btrfs]
[ 240.340523] [<ffffffffa0a488f3>] walk_down_log_tree+0x1d3/0x410 [btrfs]
[ 240.340540] [<ffffffffa0a48bfb>] walk_log_tree+0xcb/0x1d0 [btrfs]
[ 240.340558] [<ffffffffa0a507f7>] btrfs_recover_log_trees+0x1e7/0x490 [btrfs]
[ 240.340575] [<ffffffffa0a4c1d0>] ? replay_one_dir_item+0xf0/0xf0 [btrfs]
[ 240.340596] [<ffffffffa0a08b3e>] open_ctree+0x17ae/0x2030 [btrfs]
[ 240.340609] [<ffffffffa09dd633>] btrfs_mount+0x843/0x920 [btrfs]
[ 240.340618] [<ffffffff8117b7aa>] ? pcpu_alloc+0x35a/0x680
[ 240.340628] [<ffffffff811d5d68>] mount_fs+0x38/0x1c0
[ 240.340634] [<ffffffff8117bb05>] ? __alloc_percpu+0x15/0x20
[ 240.340641] [<ffffffff811f116b>] vfs_kern_mount+0x6b/0x120
[ 240.340647] [<ffffffff811f4184>] do_mount+0x224/0xb40
[ 240.340653] [<ffffffff811f4dae>] SyS_mount+0x7e/0xe0
[ 240.340661] [<ffffffff81562809>] system_call_fastpath+0x12/0x17
[ 240.340671] INFO: task btrfs-transacti:561 blocked for more than 120 seconds.
[ 240.342927] Not tainted 3.19.2-1-ARCH #1
[ 240.345175] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.348473] btrfs-transacti D ffff88020b88bd98 0 561 2 0x00000000
[ 240.348483] ffff88020b88bd98 ffff880211edc590 0000000000013f00 ffff88020b88bfd8
[ 240.348491] 0000000000013f00 ffff8802162289f0 ffff880211edc590 ffff8802094a70c8
[ 240.348496] ffff8802094d8000 ffff880200000000 ffff8802094d8000 ffff880200000033
[ 240.348501] Call Trace:
[ 240.348511] [<ffffffff811b5d1a>] ? kmem_cache_alloc+0x16a/0x180
[ 240.348525] [<ffffffffa09e07ca>] ? btrfs_free_path+0x2a/0x40 [btrfs]
[ 240.348543] [<ffffffffa0a64213>] ? __btrfs_run_delayed_items+0xf3/0x1d0 [btrfs]
[ 240.348550] [<ffffffff8155e999>] schedule+0x29/0x70
[ 240.348568] [<ffffffffa0a0b555>] btrfs_commit_transaction+0x2a5/0xbe0 [btrfs]
[ 240.348573] [<ffffffff810b4380>] ? wait_woken+0x90/0x90
[ 240.348590] [<ffffffffa0a06fc5>] transaction_kthread+0x1d5/0x240 [btrfs]
[ 240.348605] [<ffffffffa0a06df0>] ? btrfs_cleanup_transaction+0x5a0/0x5a0 [btrfs]
[ 240.348611] [<ffffffff81091748>] kthread+0xd8/0xf0
[ 240.348617] [<ffffffff81091670>] ? kthread_create_on_node+0x1c0/0x1c0
[ 240.348624] [<ffffffff81562758>] ret_from_fork+0x58/0x90
[ 240.348629] [<ffffffff81091670>] ? kthread_create_on_node+0x1c0/0x1c0
Last edited by ouroboros8 (2015-04-02 12:37:25)

My MacBook Core 2 Duo will not boot up. In safe mode I see keychain problems and Mach 1102.

My MacBook Core 2 Duo will not boot up. In safe mode I see keychain problems and Mach 1102 and it keeps circling through the same error. Also the screen is so faint (pressing the F1 and F2 keys don't do anything). I got this from a friend and he didn't have any of the original discs. Any suggestions? From what I've read it's a problem with a recent update. I've never had a Mac so I'm trying to learn and fix it.

I just had an issue like this. I was able to boot up with an external firewire drive, although it was a lot of trouble. I think doing an option boot finally worked; holding down the option key, I eventually got to see the firewire drive was bootable, and booted from it.
I put the thing in verbose boot mode (command - v , I think; but please look it up. I have no Mac books at work to check). In verbose mode, you could see that the hard drive could not mount; the OS tried to do fsck, but it failed around 2/3 of the way, and the CPU was halted.
I was occasionally able to boot normally, but never in safe or single user modes; these do a disk test first, which invariably failed.
I could see from the system and console logs when I managed to get the firewire boot going that there were repeated errors trying to access drive s03, the internal SATA drive. The logs on the SATA drive showed huges numbers of errors. At a wild guess, for some reason a lot of sectors went bad all at once. There had been a some erratic behavior before, but I'd put that down to the single processor G5 problems. (these were non video related, just freezes).
Applecare wanted me to carry the huge thing into the local Apple store, but I persuaded them to just send me a replacment hard drive, which they did. The new one works perfectly.
PowerMac G5 1.8 SP (late 2004), 1.42 mhz 14 iBook Mac OS X (10.4.3) both with 1.5 GB Ram

After installing 3.6 FF won't open even in the safe mode, I click on the icon and nothing happens at all

I installed 3.6 and now FF won't open even in the safe mode. I restored my computer setting back to where I was running 3.5.13 but it still doesn't work...some files must have been deleted when I upgraded that weren't put back even when going back to the older version but I have no idea what to look for or what to do even if I find them. Can you please help me?

Using system restore can create problems as well as solving them. I have seen system restore destroy a Firefox setup. The installation may be OK but to be sure perform a clean install
# [http://kb.mozillazine.org/Uninstalling_Firefox Uninstall Firefox]
# Delete the Firefox [http://kb.mozillazine.org/Installation_directory Installation directory], default location C:\Program Files\Mozilla Firefox\
# Download the latest version from http://www.mozilla.com/ and install it
If Firefox still does not start, try creating a new profile folder. Firefox stores user data in a profile folder, creating a new profile will show if the problem is with the old profile. For how to do that see [http://kb.mozillazine.org/Creating_a_new_Firefox_profile_on_Windows creating a new Firefox profile on Windows].
If the new profile works, you can copy selected data such as bookmarks and passwords to the new profile. For details see [http://kb.mozillazine.org/Transferring_data_to_a_new_profile_-_Firefox transferring data to a new profile]. Do not copy the preferences file, and it is best to re-install any add-ons.

Won't boot anymore but in safe mode

Similar Messages

Maybe you are looking for