WRT160 wireless network / zyxel modem problem

Hi All,
I want to ask some help with this one. I have a pc (vista) wireless connected to the WRT160 router. This router is connected to my ADSL-connection with a Zyxel modem. Everything by the book. Unfortunatly I can't get on the internet. If I connect my pc directly with this modem with a LAN-connection I can go on the internet. It seems that the router doesn't 'talk' with the modem and therefor I can't get on the internet. Can someone help me with this problem?
Thanx in advance.
Hans de Haan
The Netherlands

 Access the setup page of the router by launching an
Browser and type on the address bar, 192.168.1.1 and press enter. When
it prompts for the username and password, leave the username field
empty and provide password as "admin" (Without quotes)
click on ok.
On the main setup page the ""Internet Connection Type"" should be
on ""Obtain IP Automatically - DHCP “. Click on the Save Settings
button.
Now click on the sub tab ""MAC address clone"".
- Click on enable
Click Clone & click save settings
Check WAN Ip on Status page of router ....
If getting Valid Ip .... try going online
If you are getting Ip - 192.168.1.X ...change the LAN Ip to 192.168.2.1 ....Power cycle for 3-4 minutes ...
Try going online
If still not working ...use Internet Connection type as PPPOE .... Use Username & Password provided by Service Provider ....
Click save settings....
Look for WAN IP address again under status page ....

Similar Messages

  • Yoga 13 Wireless network authentica​tion problem

    I recently bought Yoga 13 and it is a wonderful machine, but since I upgraded to Windows 8.1, I can't connect to my university Wi-Fi.
    Recommended authentication method for the university's Wi-Fi is WPA-enterprise/TKIP and it's using personal certificates. Before the Windows update, there was the WPA-enterprise/TKIP option in Wireless Network settings, but now it's gone and it only supports WPA2-personal and WPA2-enterprise with both using AES encryption. I thought, that this is driver problem so I tried both drivers available on Lenovo Support site (I couldn't find this driver anywhere else), but that didn't work. 
    My last resort would be contacting ma faculty's IT technician, but he would charge me for setting my Wi-Fi, and I don't want to pay for something, which was working few days ago and which wasn't my fault that stopped working (stupid authentication method for university Wi-Fi constantly causing problems is different chapter entirely...)
    Thanks for any advice.

    It's not a new problem, it's a known problem that no one cares to fix and they continue to sell non-working products. I have a Yoga purchased in Feb 2014, it CAME WITH WINDOWS 8.1 INSTALLED! I invested in a brand new computer to keep my business operating smoothly, only to find out I just dumped a ton of money into the worst peice of junk I've ever owned. The intel wireless adapter is "not compatable"?!? Lenovo had me reinstall over the phone, it worked for 8 hours. Next day- no internet. I took it to the point of sale, they went to the Intel website and downloaded the driver again. That worked for another 12 hours. Every time I move locations and have a new access point, the internet doesn't work. So far the only "solution" offered is for me to send in this brand new business investment to be repaired, which could take 3 weeks. Sure, I'll close up shop so ya'll can work on a POS that was sold with faulty/ incompatible/ not yet compatible drivers (I really don't care what the issue is, only that is is a KNOWN ISSUE that Lenovo acts all surprised about). Every service person I've talked to doesn't have a clue what is going on, yet I can go online and find pages and pages of this very same (unresolved) issue!
    -different router and access point does not work
    -factory reset does not work, you're just reinstalling the same "incompatible" driver (that mine came with, I did not "upgrade" to anything)
    -BRAND NEW, internet has  been an issue since before any other programs were installed. 
    Now my pointer is missing again, so I get to waste another several hours reading through pages of similar issues to try and figure that debacle out. I miss my 15 yr old VAIO!

  • Wireless, Network-manager, dbus problem

    Hey, I'm trying to connect to wireless network at school using dhcdbd, gnome-network-manager, nm-applet... and it works but get disconnected constantly. Don't know much about networking so could use some help. Here's some output with lots of dbus errors...any ideas? Thanks.
    ** Message: <information> You are now connected to the wireless network 'XXXXXXXXXXX'.
    libnotify-Message: Unable to get session bus: Unable to determine the address of the message bus (try 'man dbus-launch' and 'man dbus-daemon' for help)
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_call: assertion `DBUS_IS_G_PROXY (proxy)' failed
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_disconnect_signal: assertion `DBUS_IS_G_PROXY (proxy)' failed
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_disconnect_signal: assertion `DBUS_IS_G_PROXY (proxy)' failed
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_connect_signal: assertion `DBUS_IS_G_PROXY (proxy)' failed
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_connect_signal: assertion `DBUS_IS_G_PROXY (proxy)' failed
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_call: assertion `DBUS_IS_G_PROXY (proxy)' failed
    libnotify-Message: Unable to get session bus: Unable to determine the address of the message bus (try 'man dbus-launch' and 'man dbus-daemon' for help)
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_call: assertion `DBUS_IS_G_PROXY (proxy)' failed
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_disconnect_signal: assertion `DBUS_IS_G_PROXY (proxy)' failed
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_disconnect_signal: assertion `DBUS_IS_G_PROXY (proxy)' failed
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_connect_signal: assertion `DBUS_IS_G_PROXY (proxy)' failed
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_connect_signal: assertion `DBUS_IS_G_PROXY (proxy)' failed
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_call: assertion `DBUS_IS_G_PROXY (proxy)' failed
    ** (nm-applet:5382): WARNING **: <WARNING> nmi_save_network_info (): Error saving secret for wireless network 'XXXXXXXXXXX' in keyring: 2
    ** Message: <information> You are now connected to the wireless network 'XXXXXXXXXXX'.
    libnotify-Message: Unable to get session bus: Unable to determine the address of the message bus (try 'man dbus-launch' and 'man dbus-daemon' for help)
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_call: assertion `DBUS_IS_G_PROXY (proxy)' failed
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_disconnect_signal: assertion `DBUS_IS_G_PROXY (proxy)' failed
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_disconnect_signal: assertion `DBUS_IS_G_PROXY (proxy)' failed
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_connect_signal: assertion `DBUS_IS_G_PROXY (proxy)' failed
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_connect_signal: assertion `DBUS_IS_G_PROXY (proxy)' failed
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_call: assertion `DBUS_IS_G_PROXY (proxy)' failed
    libnotify-Message: Unable to get session bus: Unable to determine the address of the message bus (try 'man dbus-launch' and 'man dbus-daemon' for help)
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_call: assertion `DBUS_IS_G_PROXY (proxy)' failed
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_disconnect_signal: assertion `DBUS_IS_G_PROXY (proxy)' failed
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_disconnect_signal: assertion `DBUS_IS_G_PROXY (proxy)' failed
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_connect_signal: assertion `DBUS_IS_G_PROXY (proxy)' failed
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_connect_signal: assertion `DBUS_IS_G_PROXY (proxy)' failed
    ** (nm-applet:5382): CRITICAL **: dbus_g_proxy_call: assertion `DBUS_IS_G_PROXY (proxy)' failed
    ** (nm-applet:5382): WARNING **: <WARNING> nmi_save_network_info (): Error saving secret for wireless network 'XXXXXXXXXXX' in keyring: 2

    When I configure a Wep key to my wireless internet
    sharing network, my windows installed notebook can't
    connect to my iMac. But when I set up it free the
    notebook connects easily.
    There does seem to be a known issue with a WEP encrypted software base station and Windows clients.
    As far as I am aware there is no way to get a Windows client to connect to a WEP encrypted software base station (sharing internet via Airport on a Mac).
    I tried both with ASCII and
    HEX keys and generated them from:
    You could try a ASCII key of
    1234567123456
    which will be a HEX key of
    31323334353637313233343536
    However if this doesn't work then nothing will.
    I don't know what to do and I don't want to set a
    wireless network free for security problems. Does
    anyone know a solution?
    Yes, get a wireless router and use that, it really is the only suitable solution.
    iFelix

  • Airport does not detect wireless network; it says problem = [network]"connection timeout"

    It is not a problem of signal strength, and my Airport detects other networks. It used to detect the network I want to connect to, for two years. It suddenly stopped detecting the network (which is WPA Personal password-protected). When I select choose other network and type in the password, it won't connect to it claiming "connection timeout."
    This happened before. Then after several days, Airport was able to detect and connect to the network I want. Now it again won't detect the network, and this seems permanent short of taking measures to address the problem. Should I try connecting manually to the network, and hodo I got about that? Thank you to anyone out there ho might be able to help.

    i have a macmini (OS 10.5) and use a belkin wireless router. When I turn on Mac address filtering on the router I have an Intermittent problem. The airport does not recognize the wireless network. On the network preferences panel there is a message that the airport is using a self assigned IP address. sometimes the message says the airport has no IP address. If I turn off the Mac address filtering and use a WAP password only the network is recognised and connects without a problem. How do I resolve this? I dont have the problem with a iBook using system 10.4. Is turning off the Mac address filtering secur?

  • Connecting to Wireless Network...PROBLEM

    Hello! I hope some of you out here in the cyber world can help me with a problem I am having. I was previously able to connect to my wireless router and then about two days ago, I started having problems. I would suddenly lose my connection to the internet. However, if I went back to the airport icon, and rejoined the network, I was able to get back on. Now I cannot get a connection at all. I am able to join the network and I can see the strength in the airport icon however when I try to access safari, it tells me that I can't connect because "my computer is not connected to the internet. I know the problem is not the router because another laptop in my home is connecting to the network without any trouble. I am thinking it must be something with my macbook and the settings. Any explanations?
    Any help will be much appreciated!
    Lauren
    Message was edited by: Lauren1987

    I am not sure if this is the right place to ask for help but I am desperate. I set up my wireless network at home using WPA and a password. When I set it up I set it so that the pass word would be remembered in my keychain. It worked fine until I walked away for 30 minutes and when I came back it went down. Now when I try to get back on the network my password doesn't work. When I went to my settings to investigate the problem I was shown that my password is now different it went from a 8 digit password I created to a 30 some digit password I have never seen. Can anyone help with this problem. I am running 10.4.11 and have a dlink wireless router. Thanks in advance

  • Need HELP! connecting to wireless network; IP Address problems!

    I am trying to connect to wireless networks using the AirPort built into my MacBook Pro. There are two specific networks I am trying to connect to, both are WEP protected. I know the passwords and can get into each of them but I cannot connect to the internet, which is the main reason for connecting to them in the first place! When I go into System Preferences and click on Network, I see that next to AirPort it says I am connected to the network but may not be able to connect to the internet because my computer has a Self Assigned IP address. I assume this means my computer is not receiving an IP address from the network. I am set on full auto with DHCP. So what's wrong? Please Help!!!

    That indicates that the MacBook Pro did not successfully communicate with the DHCP server on the network. Do those networks have access control (MAC address filtering) enabled? If so, the best solution is to reconfigure the base station so that this feature is disabled. This adds no real security since MAC addresses are easily discovered and cloned.
    If you can't disable access control, you will need to add the MAC address of the wireless interface of your MacBook Pro to the list of allowed clients.

  • E6-00 connection to wireless network

    I have a new E6-00 (Belle) that I use on my wireless network at home. I asked our IT boffins to connect it to the work wi-fi connection but it just will not connect. The work security is WPA-Personal/TKIP. I tried the same security setting on my home wireless network and it connected OK. Does anyomne have any ideas?

    Home wireless network: ADSL-"modem"->Wireless
    Router.
    PB G4 Airport Extreme and MacBook Intel Core 2 Duo
    Airport Extreme. Till yesterday, both laptops
    reconnected to the wireless router, automatically,
    upon waking up from Sleep. Now the MacBook does not,
    and I have to manually seek the connection to the
    router and enter the WPA/PSK password, although the
    password is saved in Keychain Access. Whereas the G4
    reconnects transparently. I have set the same
    parameters in Keychain Access in both laptops. This
    didn't help. Where, in the MacBook, should I seek
    settings that would re-establish the previous
    situation: MacBook awaking from Sleep, and
    reconnecting to the wireless router, same as the G4
    does? Thanks.
    Hello, I dont' know if this works in your case, but I recently experienced the same problem with my wireless , and after a whole lot of research and checking with Apple the solution was described in this article: http://docs.info.apple.com/article.html?artnum=304482.
    I hope this works for you as well...

  • Lost connection to wireless network on Mac Pro

    My network infrastructure at home is as follows:
    An Airport Extreme links to my DSL modem.
    One Mac Pro is connected to the Airport Extreme via Ethernet.
    One Airport Express extends the wireless network.
    Another Mac Pro connects to the extended wireless network.
    One Airport Express is used for Airtunes.
    There are also a PS3 and an Xbox 360 in the wireless network.
    Since this morning the "wireless" Mac Pro cannot see the wireless network anymore. I did not change any notwork settings and my wireless network is still saved as preferred network. Airport in OSX just cannot see it. However, I can see our neighbors' networks, so I assume Airport is working in the Mac. Upon login I get a dialog box prompting me to select a wireless network. My own network is not listed.
    All Airport base stations have a green light and show up as working fine in the Airport Utility on the "wired" Mac.
    When I use my iPod touch in the room with the "wireless" I can log into the wireless network without any problems. When I unplug the Airport Express station extending the network, the iPod's connection is much weaker or even breaks off. Thus I assume the network is fine and the base stations are indeed working properly.
    I did not change anything in the hardware or software configuration. So I am flabbergasted as to what caused the loss of connectivity.
    Any ideas, what I could try to get the "wireless" Mac connected again?
    The pearls of wisdom from the Mac community are highly appreciated.
    Cheers,
    Mustrum

    I've spent some time with AppleCare on this issue. They had me trash some preferences files, then run the Disk Utility to "Repair Disk Permissions" on my hard drive. They said this should fix it if it's a software issue, but if not then it's an Airport hardware issue, and I should take my MacBook to the Apple Store for repair.
    FOLLOW THESE STEPS
    1 - Trash these prefs files from your Library:
    - com.apple.airport.preferences.plist
    - NetworkInterfaces.plist
    - preferences.plist
    2 - Restart computer.
    3 - Go to your Network Preferences and define a new location. Then click on the little gear icon to "Set Service Order" and put Airport at the top. Click Apply.
    4 - Open Disk Utility and select your hard drive. Click on the button that says "Repair Disk Permissions". You'll see some warnings etc.
    This should work for both Tiger and Leopard. I upgraded over the weekend.

  • Airport Express (1st generation) does not reconnect to wireless network after router is cycled on/off

    Operating System: os x 10.9.1
    Airport Utility 6.3.2
    Airport Express 802.11n (1st generation)
    Linkus router: Model WRT310Nv2, Firmware Version 2.0.01
    Motorola Cable Modem: Model 2210-02, Firmware 7.7.3r5
    The Airport Express (AE) is setup to join my wireless network using Airport Utility.  A printer is connected to the AE with a USB cable.  After the setup the AE light is green and the printer can be accessed over the wireless network.
    The problem starts if the router is cycled off/on.  Now the AE will not rejoin the wireless network and there is a non-flashing amber light.  If the power to the AE is cycled off/on the AE reconnects to the wireless network.
    This is about as handy as a screen door on a submarine.
    Is it possible to see the setting of the AE the same way the modem and router settings can be accessed?   Can this issue be fixed?

    If they send you a replacement printer it will have ink tanks with it.  You can store the ink tanks from your current printer and use them later on you "new" printer if you wish.  Store them nozzle-up so they do not leak.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • Help with Time Capsule/wireless network setup

    Just purchased Time Capsule, hooked it up, and followed the instructions to create a new wireless network. The problem is that my MacBook Pro can't find the internet via the new Time Capsule network. It can "see" the Time Capsule, and I can log on with the new password, but there is no internet connectivity. If I unhook the ethernet cable from the Time Capsule and hook it directly into the computer, the computer is able to rapidly access the internet. Plug the ethernet back into the Time Capsule, and even though the Time Capsule light is green, there is no internet connectivity for that computer or other computers. Also, the Time Capsule signal strength is exceedingly low. Help!

    Please try the steps again. However, this time, I would like for you to perform a modem reset between powering all the equipment down and starting to power them back up again.
    You should find a reset button on the back of your Motorola modem.
    So, the steps should now be:
    o Power-down all of the equipment, except the modem.
    o Perform the modem reset. Note, the reset may take anywhere from 5 to 30 minutes to complete. Check your User's Guide that came with the modem. If you don't have a copy of the guide, you can get it here: SB5101 User Guide
    o Once the reset is complete, power-up the TC by following the sequence I provided earlier.

  • How can I set up a wireless network between two Mac Mini's (media centres)?

    I've just received my second mac mini (core duo, 1.83, 1 Gb ram)and want to set up a wireless network to link this with my original mac mini (PPC 1.42, 512MB) and my Belkin wireless router (g std).
    I'm using both as media centres in different rooms and want to keep all my media (films, photo's, music etc.) on one mini (connected to a 640GB external drive) and access it over the wireless network. Sort of a more felxible Apple TV setup??
    I've got the wireless network working no problems with both mini's connected to the internet over the network but I'm stuck at how I get the two mini's to see each other. I've tried "the Missing Manual" and these forums but no success so far.
    I know it can be done but would really appreciate any suggestions/directions on what to do?
    Thanks in advance<<br>
    MacMini PPC and MacMini Core Duo   Mac OS X (10.4.9)  

    Jona11-
    Greetings and welcome to the Apple boards.
    This document should be very helpful.
    Luck-
    -DaddyPaycheck

  • HP 3050 will not stay on the wireless network for more than a few minutes at a time.

    My HP DeskJet 3050 J610 is constantly dropping the wireless connection. It won't stay on for more than a few minutes. If I power cycle, it comes right back on, but drops again after a few minutes. It will print fine from a USB. When it drops off, pings time out even though the device shows "ready" in Windows 7, Windows XP and OSX. I've done everything HP suggests - static IP, upgraded firmware, diagnostic tools, etc. I am out of options.
    I can hit print right now, printer shows as ready, then I will get a print error. If I go over and power cycle the printer, my document will print - most of the time. It will remain on the network for a few minutes, then stop working. As soon as I power cycle it, I get a few more minutes before it drops. It has always done this from day one.

    I don't have another wireless network close by that I could test it on. I'm a little isolated. i might be able to work out a time when I could take it by a friend's house, but he's over an hour away.
    I have a Win 7 laptop, a Win XP desktop and an old Mac Powerbook as well as an iPod Touch and iPad 3 that use my wireless network without any problems - besides the fact that hardly any of my devices will talk to the other... But that's an OS issue. They all see the network, and the printer after I cycle the power on it.
    My wireless router is a Netgear WNR2000. I remember monkeying with the channels when I frist got this printer a few months ago, but I don't remember what all I did. Since I did a firmware update on the router, the channel is now set to Auto. If there's a channel you think I should try, let me know what it is. The printer shows up on the list of devices in the router, but that may be because I have its address reserved for the static IP. Interestingly, the router sees the printer, even though my devices cannot. I did a ping just now while checking that, and got this - which is unusual. Normally they all time out.
    Pinging 192.168.1.150 with 32 bytes of data:
    Request timed out.
    Request timed out.
    Reply from 192.168.1.150: bytes=32 time=3223ms TTL=255
    Request timed out.
    Ping statistics for 192.168.1.150:
        Packets: Sent = 4, Received = 1, Lost = 3 (75% loss),
    Approximate round trip times in milli-seconds:
        Minimum = 3223ms, Maximum = 3223ms, Average = 3223ms
    Played around a bit more pinging between devices and got this oddity - without a power cycle just a couple minutes later.
    ping 192.168.1.150 -n 50 -l 500
    Pinging 192.168.1.150 with 500 bytes of data:
    Reply from 192.168.1.150: bytes=500 time=527ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=10ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=12ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=20ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=18ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=13ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=11ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=19ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=17ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=15ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=10ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=20ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=19ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=17ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=15ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=11ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=21ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=19ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=17ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=13ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=14ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=20ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=18ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=16ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=14ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=13ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=21ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=18ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=15ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=15ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=11ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=18ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=16ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=14ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=10ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=18ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=16ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=14ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=22ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=19ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=18ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=16ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=14ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=22ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=20ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=18ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=16ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=14ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=9ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=20ms TTL=255
    Ping statistics for 192.168.1.150:
        Packets: Sent = 50, Received = 50, Lost = 0 (0% loss),
    Approximate round trip times in milli-seconds:
        Minimum = 9ms, Maximum = 527ms, Average = 26ms
    Is there a possibility that the printer is going into a standby state and having trouble waking when traffic hits? I don't know if that's possible, just seems like it looking at this.

  • Can't connect to wireless network that works fine for other machines

    I received my MacBook Pro last week (2.16 GHz) and I've been very happy with it so far. However, when I brought it home, I've had nothing but issues trying to connect to my wireless network. It's a Netgear, and you can read more about it at the following link:
    http://www.netgear.com/products/details/WGT624.php
    It works great with my Windows XP Desktop (HP Pavilion 1250n) and PowerBook G4. It works with no password, 40-bit WEP and 128-bit WEP. But not with the MacBook Pro. However, my MacBook Pro has worked at my office and StarBucks, so it works sometimes. Is there something special I have to set on my router for it to work with the MacBook Pro?

    I also had problems with wireless connectivity while trying to access a netgear WGR614 albeit a v2 base station.
    The problem was that I could not see the network from my MBP. It just didn't appear. The network was open with zero security. However my dell laptop was able to connect fine.
    I noticed in the MBP config that the wireless locale was set to USA. I however live in Ireland. I then changed the locale inside the netgear 'wireless settings -> region' to United States. Now everything works fine. My dell didn't seem to care either way. It just picked up the new 'USA - region' based wireless network.
    The problem now is that I travel quite a lot and usually I won't have the luxury of being able to change the routers configuration.
    Is this just a MBP and Netgear WGR614 issue?
    If this happens in the future is there a way for me to change the AirPort wireless card locale?
    MBP 15" Core 2 Duo   Mac OS X (10.4.8)  

  • Can't Get Time Capsule to Extend Airport Extreme Wireless Network

    I've searched this forum and read dozens of listings, but nothing I've found gives me a answer for the problem I'm having.
    I had an existing network consisting of three Airport Extreme routers, one the master/DHCP server and the other two to extend the network. All of the routers were configured for 802.11n 5 GHz only service.
    After much frustration trying to use Time Machine to back up to external disks attached to Airport Extremes as well as disks attached to other Macs, I gave up and bought a Time Capsule.
    I have been trying for about six months on and off to get the Time Capsule configured as an extension to the main Airport Extreme as the other two Extremes are.
    Nothing I've tried will cause the TC to extend the network. It always comes up with a yellow light and error messages saying that there is a problem with the wireless network and a problem with the internet connection and, sometimes, a third message that I don't remember.
    After my initial efforts, I just gave up and plugged the danged TC into the remote AE that is closest to where I use my MacBook Pro and it worked. But I wanted it to REPLACE that AE instead of being an appendage to it.
    Due to TC/TM problems, I've twice lost the entire TM backup off of the TC, and tonight I decided it was time to start over. I've encountered the same problems as before, and so finally moved the TC to my home office rack where the main AE is located and plugged it into the AE directly. TM is now backing up, but at a snail's pace (which is why I wanted the TC to be located in the same room where I use the laptop).
    Has anyone had success or failure extending a multiple-unit AE network with a TC on 802.11n 5 GHz (not WDS)? If not, has your experience been similar to mine; if so, what did you do that I haven't?
    Any specific help will be greatly appreciated.

    Yes, I suppose I could do that. But if the wireless extension isn't working in one direction there's no guarantee it'll work in the other direction; and I was trying to avoid upending my entire setup.
    And no, I'm not bridging the units with hard-wired cabling; I'm attempting to use wireless to extend them...NOT WDS, which is for 802.11B/G mode, but the 802.11N wireless extension mode that's available on these Apple products.

  • No longer detetects any wireless network

    Hi
    My macbook was correctly connected to the Internet via my wireless network, and then it suddenly disconnected. It no longer detects any wireless networks (and there are quite a few usually!)
    I tried to turn airport off & then back on, but no change.
    I then tried to reboot my macbook, but no change either.
    When it searches for wireless networks, it is very slow (sluggish).
    I also booted on Windows 7 (dual boot), and it has *exactly the same* problem. Leads me to believe that it is a hardware problem, more than a software one..
    The only recent change: I moved from the UK to France few days ago => new ISP & new router (but I doubt this could be the source...)
    Is there anything I can do?
    Replace the wireless card?
    Thanks

    By the sounds of it, I've been having exactly the same problem. I will be using my macbook and suddenly the airport will drop out for no reason. Sometimes I can reconnect but often I'll have to try a dozen times or more, with the connection timing out each time. I've actually set up two differently named wireless networks at home to solve this - for a while, if one dropped out, I could reconnect to the other one. Even this has now stopped working. I've tried flicking airport on and off, restarting the airport base stations, I even have one of the wireless networks configured as WDS sending to an airport base station within a couple of metres of where I normally use my machine. Nothing works. I've tried deleting ~/library/preferences com.apple.internetconfig.plist and com.appleinternetconfigpriv.plist and rebooting - for a few times that would fix it, but not any more.
    The strangest thing, though, is that if I switch user accounts, I can access the wireless networks again no problem.
    It's almost like there's something that needs flushing in the user account's wireless settings - a buffer, or a cache, or something. It'll generally only happen once I've been using the machine for a sustained period of time.
    I'm running 10.5.8 with Wireless Card Type: AirPort Extreme (0×168C, 0×86) Wireless Card Firmware Version: 1.4.16.2 if that's of any help to anyone.

Maybe you are looking for