WRT300N Router does not working with Intel 4965AGN adapter on Wireless-N

Hi! I have recently bought the laptop Acer 5920G with Intel 4965AGN network adapter and Windows Vista. I have read that WRT300N Router is supporting Draft-N standard, so I purchased it. The router is working fine on Wireless-G 54Mbps (firmware - 2.00.17), but not on Wireless-N. I tried to enter the following settings: ssid - any non-linksys name; radio band - wide; n-channel - 9; standard channel - 11; beacon interval - 50; Fragmentation threshold - 2306; RTS threshold - 2307, but nothing has happened, connection still remains 54Mbps. How should I configure the router and network adapter to get Wireless-N?

okay... try reflashing/upgrading the firmware on the router, after reflashing the firmware on the router, reset it back to default settings and reconfigure it according to ISP settings...edit the wireless settings again, make sure that "wireless mode" should be mixed...
on the vista computer, click on start >> control panel >> network & sharing center >> manage wireless network and try removing existing wireless networks from profile and manually add wireless n/w profile according to wireless settings of the router...check whether it makes any difference or not and let me know.

Similar Messages

Window 10 build 10041 does not work with Intel 82579V Gigabit Ethernet on ASUS motherboard

I originally posted this question here:
answers.microsoft.com/en-us/insider/forum/insider_wintp-insider_update/window-10-build-10041-does-not-work-with-intel/6729892f-83aa-4822-b20a-ea84f4fd06c7
and was asked to post it on this forum...
I updated a computer I have which is a quad core i7 that I built and includes an ASUS motherboard with Intel 82579V Gigabit Ethernet built in. Windows 10 preview 9926 worked fine with this network adapter. Window 10 build 10041 does not, and I have tried
it twice so far. I even went as far as buying a Thunderbolt-Gigabit Ethernet Adapter (Broadcom, sold by Apple)... and while it installed the driver automatically, it did not work either. Each time you try to view the properties of either of them, it locks
up or give an error. In fact, doing much of anything with the Intel adapter icon assures you of not being able to do a clean reboot... have to kill power. I have finally gone back the previous version 9926, which has its issues but no where near as bad
as not having any network connectivity! Does anyone have this issue and a workaround?
Note, there are two images on the windows 10 preview forum that I posted this question on. I could not post the full link as I was getting a message here that links and graphics are not allowed.

Thanks Roger, I posted the following yesterday in the other thread (thinking it was this thread - confusing after they moved it here)... It may be that the new driver fixes the issue that 10041 has with it, but I have not tried that yet. If I do I will update
this... Thanks!
I have more information about this, which basically exonerates any issue with the Intel 82579V Gigabit Ethernet hardware or software. I have 3 computers with Windows 10 preview so I have multiple angles to see issues from. With this I have found a culprit
(but I suspect not just the only culprit) in this above mentioned problem...
10041 build combined with installing (or attempting to install) CISCO VPN Windows 7 64bit 5.0.07.0440-k9 client causes the issue mentioned above. I confirmed this on a completely different machine with a totally different Ethernet adapter. First machine
is an ASUS motherboard in a tower system I built, with the Intel 82579V Gigabit Ethernet hardware built in. Second machine is a Gateway Laptop from 2008 which has a Marvell Yukon 88E8057 PCI-E Gigabit adapter built in. Build 10041 will work fine with my 2008
laptop, including the MS VPN client (which I have tested). However, if you attempt to install or even uninstall the Cisco client you will have to do a recovery to a restore point (as I have done twice) in order to get your network working again. Installing
or attempting to install (because it never even does install properly and times out), CISCO VPN client will render your entire network unusable. Going back to a restore point saved me and I am still running 10041 but I can't use CISCO VPN client any longer.
I could with build 9926, including on all 3 machines. I now have 9926 on two machines and 10041 on only the 2008 laptop.
Hopefully this above information helps someone resolve the issue. I will also mention, even though my network is working on the 2008 laptop, I still can't go into the Control Panel\Network and Internet\Network Connections and right mouse click on the Marvell
Yukon 88E8057 PCI-E Gigabit adapter icon. I get an error when clicking on Properties menu popup : "An unexpected error has occurred". So something is still up with my network adapter driver or windows software, but it could be a side effect of all
that has happened with the Cisco software install attempts under 10041.
Another note: CISCO Anyconnect also has the issue.

I have recently upgraded my iMac Intel G5 iSight to OS 10.6.8 and now the internal mic does not work with skype or facebook. I can here static when playing back clips. Do I need to update firmware or reload old sys parts

I have recently upgraded my iMac Intel G5 iSight (iMac5,1) to OS 10.6.8 and now the internal mic does not work with skype or facebook. I can here static when playing back clips. Do I need to update firmware or reload old system parts. I have zapped PRAM. The blue indicator in system audio panel will appear for a second as I slide the bar for internal mic but then it disappears. Is there a fix?

The sound seems very faint but can here static on playback.

You must have connected the Time Capsule with a router that does not work with my direct cable from my ISP

you must have connected the Time Capsule with a router that does not work with my direct cable from my ISP

I tried to answer in your other post.. please stick to one thread ..
What method of internet do you have.. is this fibre install.. if so the TC should just plug in and use dhcp in router mode.. press and hold the reset and it will go back to router mode by default.

My Time Capsule does not work with existing WiFi

Following a question solved on March 24 by LaPastenague, but gone bad again.
Apple AirPort Time Capsule
I felt the need for a physical backup of my data, as I would not completely trust the different clouds. I use, and have used Dropbox for 4-5 years and are very satisfied with that, but I am still not sure if or when a political lunatic will shut off the internet.
I purchased the Apple AP Time Capsule 2T, because all my other stuff are Apple, and that it's wireless. My old backup is Maxtor 300 GB.
Since we stay 2-3 weeks on two locations, one in Norway and one in Sweden (two different countries) we must use Mobile Broadband 4G, cables or fibre connections are useless for us, and we don't have it up to the houses. I have one mini router for each country, we bring with us iPhones, iPads, iMac, Apple TV, APExpress. When we pass the boarder I change the mini router, and the system continues working perfect on the WiFi, except the APExpress that needs to be reconfigured, but then it works.
The APTC was difficult to make working as it would not accept to be in an existing network, but with good help from the Apple Community, LaPastenague, with forcing the TC connect to the APE with Ethernet cable in bridge mode, ref "My Time Capsule does not work with existing WiFi" from March 24, the problem was solved and all gadgets worked together in a perfect harmony, until we changed location.
Now, as I have my second WiFi network, and the APExspress is reconfigured, it's like the TC thinks, I am the base boss here, I am not taking orders from APE one more time, and it simply does not work, not only that, it fluctuates all the time.
I have a slight feeling that the two WiFi bands are making the trouble as during the configuration of the TC sometime the last figure 6 and 7 pops up, and that has something two do with the two different 2,4 and 5 GHZ bands
So, I am curious if you have any idea ?
I am thinking of returning the TC if I don't make it work now, but how do I delete all the data that's on it?

I can deal with the last question first and easily.
I am thinking of returning the TC if I don't make it work now, but how do I delete all the data that's on it?
Open the airport utility .. go to the disk tab and select erase.
When you select erase you will get mulitiple options.
Quick removes the file table but does not delete the files,, it takes 2min or less.
A Zero out data is the secure way,, by writing 0 ie low level drive format.
It can take several hours..
7 pass will take a week.. not recommended..
35 pass erase is ridiculous.. it would take a month.. put an ax through the TC. It is quick and better.
Now, as I have my second WiFi network, and the APExspress is reconfigured, it's like the TC thinks, I am the base boss here, I am not taking orders from APE one more time, and it simply does not work, not only that, it fluctuates all the time.
The fact that it did work and has now failed might point to faulty unit.
The only way to tell is reset it properly to factory and start over.
Universal Factory Reset.. any model TC or AE.
Unplug your TC/AE from power or turn off at the power point.
Hold in reset. and power the TC/AE back on.. all without releasing reset and keep holding in for about 10sec. (this is often difficult without a 2nd person or a 3rd arm).
Release it when the status light flashes rapidly. If it doesn’t flash rapidly you have missed it and try again.
Note..
Be Gentle! Feel the switch click on. It has a positive feel.. add no more pressure after that.
TC/AE will reboot after a couple of minutes with default factory settings and will wipe out previous configurations of the router.
No files are deleted on the hard disk in a TC.. No reset of the TC deletes files.. to do that you use erase from the airport utility.
Generally having multiple wireless AP should not cause problems.. but it is better to set channels manually.. so it doesn't go beserk rotating channels.
Remember to keep all names short, no spaces and pure alphanumeric.
Sadly though the Apple routers have no logging now and no SNMP and almost nothing to help diagnose a problem, so if it continues .. take it back to apple.. they have given you no other method of fixing it.

Adobe Flash Player does not work with Safari. What can I do?

Hi,
I have a MacBook Pro, Retina, 15 inch, late 2013, 2 GHz Intel Core i7, using OS X 10.9.4. I have installed Adobe Flash Player. In my System Preference, in the advanced settings, it is set to install updates also tells me that I have the NPAPI Plug-in (version 14.0.0.145) installed but not the PPAPI Plug-in. Is this the reason why it does not work with Safari (keeps telling me to download the app, which I did but still does not work)? Is there any way I could fix the problem? Please, help.
Thanks.

If you can't install or update Flash, follow these instructions.
If you have installed the latest version of Flash, please take each of the following steps that you haven't already tried. After each step, relaunch Safari and test. For a "missing plug-in" error, start with Step 8. Back up all data before making any changes.
Step 1
You might have to log out or restart the computer before a Flash update takes effect.
Step 2
From the Safari menu bar, select
          Safari ▹ Preferences... ▹ Privacy ▹ Remove All Website Data...
and confirm. Close the window. Then select
           ▹ System Preferences… ▹ Flash Player ▹ Advanced
and click Delete All. Close the preference pane.
Step 3
If you're only having trouble with YouTube videos, log in to YouTube and load this page. You may see a link with the text "Leave the HTML5 Trial." If so, click that link.
Step 4
a. If you get a warning of a "blocked" or "outdated" plug-in, then select the Security tab in the Safari preferences window. In the list of plugins on the left, there should be one—and only one—entry for "Adobe Flash Player," showing the same version number that you installed. Select that entry. On the right there will be a list of websites for which you have specifically allowed Flash, if any. It's normal for the list to be empty. Below that is a menu labeled
          When visiting other websites
From that menu, select either Allow or Ask.
b. If you still get the alerts, then go back to the Flash Player preference pane and select the Advanced tab. Click Check Now. Quit and relaunch the browser.
c. If the alerts still persist, triple-click anywhere in the line below on this page to select it:
/System/Library/CoreServices/CoreTypes.bundle/Contents/Resources
Right-click or control-click the highlighted text and select
          Services ▹ Open
from the contextual menu.* A folder should open. Inside it, there should be a file named "XProtect.meta.plist". If that file is missing and you know why it's missing, restore it from a backup or copy it from another Mac running the same version of OS X. Otherwise, reinstall OS X.
*If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
          Go ▹ Go to Folder...
from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return.
Step 5
In the Safari preferences window, select the Advanced tab and uncheck the box marked
          Stop plug-ins to save power
Step 6
Open this folder as in Step 4:
/Library/Internet Plug-Ins
Delete the following item, or anything with a similar name, if present:
          Flash Player (failing).plugin
You may be prompted for your login password.
Step 7
Re-download and reinstall Flash. Download it from the domain "get.adobe.com". Don't click a link from any other website, including this one, because you can't trust links. They may be an attempt to trick you into installing malware masquerading as Flash. Type the address into the browser window. Never download a Flash update from anywhere else.
Step 8
If you get a "missing plug-in" error, select
          Safari ▹ Preferences... ▹ Security
from the Safari menu bar and check the box marked
          Allow (or Enable) plug-ins
Then click the button marked
          Manage Website Settings...
if present and make sure that the website is not blocked for Flash.
Step 9
Select
          Safari ▹ Preferences... ▹ Extensions
from the Safari menu bar. If any extensions are installed, disable them.

T60 does not boot with Intel T7600G CPU

I replaced my Intel Core Duo T2400 with Intel Core 2 Duo T7600G CPU in ThinkPad T60(1951-CTO) laptop. However, laptop does not boot with Intel Core 2 Duo T7600G CPU. It doesn't even complete the POST: https://db.tt/8UL8FlE0 As seen in the video, I plugged in the power adapter at 0:02 and pressed the power button at 0:06. One can hear a little click made by optical device. If I press the power button again at 0:16, this click does not happen. BIOS version is 2.27. I have reset the BIOS settings by disconnecting the CMOS battery, but this didn't help. Once I replace the T7600G with my old T2400 then I'm able to boot the laptop.
Any ideas what might cause such behavior? Shouldn't there be beep codes in case of CPU issues? What else to try?

TuuS wrote:
600X wrote:
Since you came from a T2400, does your T60 even have a Rev. 3 motherboard? If it does not, then no Core 2 Duo will work, only Core Duo's.
I don't claim to be the top authority on T60 motherboards, but I believe any will use a Core 2 T7600, 7400, 7200 if the firmware is updated.
My own experience mirrors what TuuS has stated. I have yet to see a T60/p from any walk of life with a recent BIOS that will bark at a proper Core 2 Duo CPU.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

In Photoshop CS6 Hue Saturation does not work with forground/background Jitter set at 100 percent no change in color is observed. Help

In Photoshop CS6 Hue Saturation does not work with forground/background Jitter set at 100 percent no change in color is observed. I have Added a screen Shot of the Brush settings and a demonstration of what the brush produces.
I also notice That when I make a pattern of a single color, when I fill a selection with the pattern I get a rainbow of different colors.
I am running a 64 bit version of Photoshop from the CS6 Masters Collection
I am on a PC with a Intel i7 1366 4 physical cores and 8 threads, 24 Gig of DDR memory, A Crucial 512 Gig SSD and a NVIDIA GTX 570 with 2 Gig of memory.
The document size is 2100 by 1500 Pixels at 300 PPI only two layers

In Photoshop CS6 Hue Saturation does not work with forground/background Jitter set at 100 percent no change in color is observed. I have Added a screen Shot of the Brush settings and a demonstration of what the brush produces.
I also notice That when I make a pattern of a single color, when I fill a selection with the pattern I get a rainbow of different colors.
I am running a 64 bit version of Photoshop from the CS6 Masters Collection
I am on a PC with a Intel i7 1366 4 physical cores and 8 threads, 24 Gig of DDR memory, A Crucial 512 Gig SSD and a NVIDIA GTX 570 with 2 Gig of memory.
The document size is 2100 by 1500 Pixels at 300 PPI only two layers

Satellite A300-1G2 does not work with 3GB or 4GB of memory

Does not work with 3GB or 4 GB memory, only 2 GB!
And if I plug one memory module of 2 GB in bank1 (bank0 is empty) - it's does not work too!
It's happened with 3 notebooks. (Sorry, my English is not good :) )

Did you think about one fact that the notebook doesnt support 3GB or 4GB RAM?
No?
Maybe you should check the user manual firstly which is preinstalled on the notebook.
I think you would find very important info.
Notebooks with Intel Mobile GL960 chipset supports max memory capacity of 2GB!!!
As Im not mistaken your notebook was equipped with the Intel Mobile GL960 chipset so the case must be clear now. or not?
Additionally is important to know that you have to use always first memory bank/slot (bank0) if you are using ONLY one memory module!!
Bye
I think you can assign 10 points ;)

Flash player does not work with new ICS Android 4.0.4 OS. Has this problem been addressed?

Flash player does not work with new ICS Android 4.0.4 OS. Has this problem been addressed? I am using Firefox Beta for android and I also tried just Firefox.

Please check the Play Store app for any Flash updates and install them if present.

Flash player does not work with Ie or Firefox with win 8.1?

Flash player does not work with Ie or Firefox with win 8.1 64, If i try and play a video I get the message to install Flashplayer.
If I try and install it it says it is already installed. Your onsite installer says it is not applicable to my machine.
I have followed all the normal steps re enabling addons and active filters etc.
all to no avail Pc is Dell 6 months old, Flashplayer has never worked on this machine. Last MS update mid Dec 2014.
Version of flashplayer is 15....03.......

Flash Player is a built-in component of Internet Explorer. There's nothing separate to download or install.
Firefox requires a different version of Flash Player (the NPAPI plug-in), which will be served to you if you go here: http://get.adobe.com/flashplayer using Firefox; however, there are some unique stability issues related to Firefox on Win8.1, and you're probably better off using Google Chrome if you want a more optimal experience with Flash Player.
For problems where IE isn't being detected by sites that require Flash:
First, confirm that ActiveX Filtering is configured to allow Flash content:
https://forums.adobe.com/thread/867968
Internet Explorer 11 introduces a number of changes both to how the browser identifies itself to remote web servers, and to how it processes JavaScript intended to target behaviors specific to Internet Explorer. Unfortunately, this means that content on some sites will be broken until the content provider changes their site to conform to the new development approach required by modern versions of IE.
You can try to work around these issues by using Compatibility View:
http://windows.microsoft.com/en-us/internet-explorer/use-compatibility-view#ie=ie-11

ITunes 12.1.1 does NOT work with Windows - Fix??

Hi everyone,
I had issue after issue with the latest iTunes update (12.1.1) not working on my windows 7. It simply would not lunch when clicking on the shortcut to open.
After a fair bit of searching I found this alternative version which seemed to do the trick and now it works:
iTunes 12.1.1.4 for Windows (64-bit - for older video cards) - iTunes64Setup.exe(2015-02-18)

The "for older video cards" installer - which, like most prior "64 bit" versions of iTunes, is actually a 32 bit application with a 64 bit installer - may be a useful fallback if the full 64 bit version does not install or run correctly. Although 12.1.1.4 is a major improvement over 12.1.0.71, there are clearly still some lurking incompatibilities with some 64 bit Windows systems/components. It is, however, a little misleading to say that "iTunes 12.1.1 does NOT work with Windows" - in many cases it works fine without switching to the alternative version. I have the full 64-bit version of 12.1.1.4 running on three systems - two Windows 7 and one Windows 8.1 - no issues with either installation or operation on any of them.

Home sharing does not work with new mountain lion update.

home sharing does not work with new mountain lion update. Does anyone else have the same issue. Updated all computers in my home, deauthorized and reauthorized each computer. turn off home sharing and turned it back on. don't know what else to do..please help...

Our Apple TVs continue to lose connection ever since installing Mountain Lion on the host computer. The only thing that fixes them is to quit and relaunch iTunes, which only works unti the ATV goes to sleep. If a movie is paused for more than a few minutes and the ATV goes to sleep, pressing play again on the remote is greeted with "There are no movies on this computer" or "Turn on Home Sharing."
If we stop a video on one ATV and attempt to resume it in another room, the error begins again. The other ATV can't connect until iTunes is relaunched.
My guess is that it has something to do with the new [annoying] security settings. But I still haven't found a fix other than restarting iTunes everytime we want to watch something from our downloads. Fail.

External USB HD does not work with HAL:

External USB HD does not work with HAL:
From the last 10 days the HAL auto-mount with ntfs-3g file system of my external hard drive does not woks.
But the manual mount procedure with the command mount -t ntfs-3g /dev/sdb* /mnt/XYZ works.
I've followed the instructions in the wiki: http://wiki.archlinux.org/index.php/HAL and the system has worked up to the last kernel or HAL update.
My fat32 usb-stick works without any problem.
If I try to open the device with KDE it appears an error popup wit this message:
TODO: have to rethink extra options
Error: kio_media_mount_helper
The log from the kernel.log is
Nov 6 22:03:16 myhost usb 5-1: new high speed USB device using ehci_hcd and address 4
Nov 6 22:03:16 myhost usb 5-1: configuration #1 chosen from 1 choice
Nov 6 22:03:17 myhost Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Nov 6 22:03:17 myhost ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Nov 6 22:03:17 myhost Initializing USB Mass Storage driver...
Nov 6 22:03:17 myhost scsi6 : SCSI emulation for USB Mass Storage devices
Nov 6 22:03:17 myhost usb-storage: device found at 4
Nov 6 22:03:17 myhost usb-storage: waiting for device to settle before scanning
Nov 6 22:03:17 myhost usbcore: registered new interface driver usb-storage
Nov 6 22:03:17 myhost USB Mass Storage support registered.
Nov 6 22:03:22 myhost scsi 6:0:0:0: Direct-Access WDC WD32 00JB-00KFA0 0811 PQ: 0 ANSI: 0
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sdb: sdb1
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Attached SCSI disk
Nov 6 22:03:22 myhost sd 6:0:0:0: Attached scsi generic sg2 type 0
Nov 6 22:03:22 myhost usb-storage: device scan complete
and the error.log is
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Do you have some idea ....
Bye.

I have done the following:
Downloaded the patched hal version.
used makepkg in /abs/local/trunk/ to create a pkg for pacman
used sudo pacman -U pkgname to install it.
used sudo nano /etc/hal/fdi/policy/preferences.fdi to create the fdi file with the following content:
saved the file and removed my ntfs entryes from fstab and rebooted. and still there is no automount off ntfs partitions.
have i done something wrong?
br fjodork
WARNING: what follows is a guide of what did work for me, I'm still in an early stage of learning linux, so please correct me if anything of what follows is wrong/dangerous/stupid. As I said, this worked for me, it's not pretty, since I was learning each step on the fly and I'm sure there are better ways to do this.
So fjodork, you seem to have done the the necessary steps, though i couldn't get it to work until i first removed hal without dependencies
pacman -Rd hal
it will give you some warning about the dependencies, ignore it since we are reinstalling hal in a few steps.
First i tried to follow Raymano's link, obviously it showed me nothing in the browser so I thought it might be a broken link.
So I downloaded the source tarball from here http://hal.freedesktop.org/releases/hal-0.5.10.tar.gz
unpacked it changed the /tools/hal-storage-mount.c as per Milfadoodle's instructions.
at first I tried to compile directly from source, the process would finish without a glitch though after reboot nothing changed, as if hal weren't
installed, i guess there were issues with paths. anyway read on
Then repacked the source in tarball, copied it to /var/abs/extra/system/hal and modified the PKGBUILD as follows
makedepends=('pkgconfig' 'gperf')
options=('!libtool')
install=hal.install
source=(${pkgname}-${pkgver}.tar.gz #removed url so makepkg looks in the current directory for the tarball
hal
hal-policy.patch
cryptsetup_location.patch
hal-0.5.9-hide-diagnostic.patch
ntfs3g-valid-options.patch)
md5sums=('6641c30a27c00485c6accac5110ff911' # replace with md5sum of your package's sourceball (run md5sum filename)
'882f67668cb14a0a9e4a27ef22278027'
'5ba8b610aa9763a5f42b9f7cbd7a86ad'
then makepkg (i had to add --asroot, don't ask why
and finally pacman -U hal-0.5.10-1-i686.pkg
another reboot and everything worked without a glitch!:D (yeah i know i still haven't got rid of the reboot mentality )
I have also put the policy files as per the wiki instructions.
PS: I know this is a dirty way to getting things done but as i said, I'm just starting
If anyone could comment/correct/explain this post I'd be more than happy, the automount issue was bothering me for about a month now (you'll say why do I need ntfs in the first place? well, I only recently switched for Linux as my primary OS, these are some relics of the M$ era

APPLE TV DOES NOT WORK WITH NETFLIX

APPLE TV DOES NOT WORK WITH NETFLIX, just a black screen and "Netflix is loading" message appears. I can´t even see Netflix´s home page or set up my account. Netflix is working fine on all other devices at home, but in Apple TV.
I have tried the 8.8.8.8 DNS trick, the turn off procedure, the manual IP setting, but nothing....black screen still appears

It started working.....!!!!! (It seems someone back there is listening)
I "forced" an upgrade, I mean it showed "AppleTV is updated", nevertheless I re-started the system using the "return to original configurations" option. Then it updated again by itself to a newer version....and started working perfectly.
I have paired my apple wireless keyboard and it works fine, this way is easier to set up passwords or so (you can also do it with your remote).
TIPS:
I didn´t change any language or video quality configuration (scared to do so)
I changed to ethernet (cable) instead of wireless
My internet plan is 6 Megabytes (it was the same while it wasn't working)
good luck!!

WRT300N Router does not working with Intel 4965AGN adapter on Wireless-N

Similar Messages

Maybe you are looking for