WRT54G - IP and Port mapping problems

I'll set the scenario first so you can understand what i'm trying to do. I have a D-Link 524 configured trough PPoE to get access to internet. It has DHCP enabled (from 192.168.0.100 to .199). I had static ip configured in the D-Link router as 192.168.0.90 and some ports forwarded to my pc that's like 50 meters away from the router, in other office. The thing is, I added a WRT54G v6 router cause the wireless signal from the d-link didn't reach where I am, and some people needed to use it. So, I plugged my pc to the WRT54G, and the linksys to the D-Link. No, my problem is, I no longer have the static ip that the d-link assigned me (the linksys uses the 192.168.1.X range, and the d-link the 192.168.0.X range). Now, if I release my MAC address from the D-link and assing a static ip in the WRT54G, I could fordward the ports I had before in the d-link but in the linksys. The thing is, I can't find a way to assing a static ip in the linksys. And I tried to change the range of ip from the linksys to 192.168.0.X so I can still use the assigned address from the d-link but it didn't work, I couldn't access the linksys neither the d-link after changing the address, didn't get internet either, so i had to reset the linksys. After all of this... what the hell do I do Azureus can't connect, or any other P2P app for that matter (cause I had the ports forwarded in the other router, and I can't forward them in the linksys cause I get a dynamic local ip, if I forward them to, say 192.168.1.100 and some day I get assigned 192.168.1.101... well, I assume it won't work as expected)

The WRT54G does not assign fixed IP addresses through DHCP. You have to set a static IP address on the computer itself instead of using DHCP.
I would, however, recommend not to use the WRT as router but only as simple access point. Instructions are here. Set a LAN IP address like 192.168.0.2 on the WRT to keep it accessible inside your normal LAN. I think this setup will solve all your problems. You can still use the fixed IP address assignment from the DHCP server on the D-Link and you only have to configure a single port forwarding on the D-Link (instead of two which would be necessary if you connect the Linksys router through its internet port to the D-Link).
With two access points you can create a roaming network by using the identical wireless settings on both routers (SSID, wireless security, wireless mode). Channels should be different and at least 5 apart. SSID broadcast should be enabled on both. Now most wireless clients are able to move between both access points without loosing the connection.
Message Edited by gv on 06-01-2008 02:22 PM

Similar Messages

Port Mapping Problem with AEX

I have a new Airport Extreme and a problem that did not exist with the Airport. I connect a Toshiba network camera to an Airport Express, set as a WDS remote, with the netcam connected to the wired ethernet port of the Express. I can see the netcam, which also functions as a web server, on the internal 10.x.x.x address, and have reserved a discrete 10.x.x.x address via the MAC/DHCP reservation function of the Extreme. Just like the older Airport which did this without a hiccup, I should be able to map a port (e.g. 1200) on the public IP to port 80 of the internal 10.x.x.x address, then access the netcam on the internal network from any browser (http://67.x.x.x:1200). My cable modem is just that: no router involved other than the Airport Extreme. I'm using the latest Extreme and Express firmware, and am either missing something with the new Leopard firewall, overlooking something else, or dealing with a product flaw. Any help is appreciated and Happy Holidays.

I have forwarded the port (have tried several different ports actually) in what I think it the correct way: using the Airport Utility, connected to the Airport Extreme, and, under advanced options, selected port mapping, entered the public TCP port of 1200, then the private 10.x.x.x IP address of the netcam (which I can access from the internal network with no problem), coupled with the private TCP port of 80. I then attempt to access the netcam from the Internet by entering http://my cable modem IP address:1200 (or another port to which I've attempted to map). This method worked for two years with the Airport, but, with the Extreme and Leopard (simultaneous transition), I'm stumped. After reading other about other port mapping problems, I reserved an IP address for the netcam based on its MAC with no positive results. I also set the firewall through the Security icon in System Preferences to allow all incoming connections. Thanks for taking the time to respond.

WRV200 port mapping problems.

I did the port mapping to enable direct IP dialing from Linksys PAP2 VoIP adapter. It worked fine, untill I replaced the old router with a new WRV200.
The funny thing is the mapping works for some time, then it stops to work. To bring it back to work I have to restart the WRV200 router.
Everything worked fine with old Digitus DN-11005 router. I did not changed the settings in the PAP2 adapter. And, I used the same port mapping settings with WRV200 router. The PAP2 is set to DHCP and static IP is set through static DHCP client list in WRV200.
The only change from the old Digitus LAN settings is a different subnet IP. The old one was 192.168.123.0 the new one is 192.168.122.0
The direct IP dialing is done through WAN of the local Internet service provider. Both locations had the same Digitus router and PAP2 adapters installed with the same port mapping and PAP2 adapter settings. Now with one router changed to WRV200 the system does not work correctly. It looks like the port mapping in WRV200 stops working in about an hour after last usage of this feature.
Static CP Client Lis

I've been busy playing with the issue. Looks, like it is not the port mapping issue, after all.
The LAN is constructed from the WRV200 router and a Surecom EP-805SX 5 port switch connected to one of the router ports. The PAP2 adapter is connected through the switch.
When the PAP 2 appears to be locked it does not make outside calls, and it does not receive them. SIP registering does not work, as well. So, the communication with Internet does not work. In the same time, I can access the web config page of the PAP adapter. To bring everything back to normal I need to pull out and back in one of the WRV200 LAN port plugs. So, reseting of the whole router is not necesary, because disconnecting one of the LAN ports does the trick. What is bugging me is, it works with any of the 4 LAN ports. It does not have to be the LAN port the PAP2 is connected with.
I've noticed, also, a computer connected to the same switch the PAP is connected with has some problem to communicate with the DHCP server of the WRV200 router, from time to time.

FTP and Port mapping

Hi
we get troubles with our FTP Server. The clients send a Syn with Src port 40000 then the Server replies with the the same dst port but i presume that the loadbalancer makes a port-mapping and translate the source Port to eg. 33000. Our firewall clearly drops the packet with the reason "Packet out of state". have you any idea ?
Here my config
service h01p6u_21
keepalive type tcp
keepalive port 21
ip address x.x.158.129
protocol tcp
redundant-index 11790
active
service h01p6v_21
ip address x.x.158.130
keepalive type tcp
keepalive port 21
protocol tcp
redundant-index 11800
active
content c01sg5_21
vip address x.x.x.140
add service h01p6v_21
add service h01p6u_21
port 21
protocol tcp
application ftp-control
active
!*************************** GROUP
group srg_c01sg5
vip address x.x.x.140
add service h01p6u_21
add service h01p6v_21
active

Hi Gilles
the problem that I have now is with ACTIVE FTP. I made PBR on the Loadbalancer. Passive FTP works either from the internet and from our internal network while Active FTP works only from the internet and doesn't work from our internal network. What we see is that the Loadbalancer sends the ftp-data packet out to the InternetVLAN (eg. VLAN 3605) and not to the VLAN 3603. I guess the problem is in my access-list. have you any Idea ??
My configuration
!*************************** GROUP ***************************
group srg_c01sg5
vip address x.x.152.140
add service h01p6v_21
add service h01p6u_21
active
!**************************** ACL ****************************
acl 1
clause 10 permit any x.x.172.0 255.255.255.0 destination any prefer FW_VLAN3605
clause 99 permit any any destination any
apply circuit-(VLAN3607)
acl 2
clause 10 permit any x.x.158.0 255.255.255.0 destination any prefer FW_VLAN3603
clause 99 permit any any destination any
apply circuit-(VLAN3610)
clause 15 permit any x.x.158.0 255.255.255.0 destination 10.0.0.0 255.0.0.0 prefer FW_VLAN3603
clause 20 permit any x.x.158.0 255.255.255.0 destination 138.191.0.0 255.255.0.0 prefer FW_VLAN3603
clause 25 permit any x.x.158.0 255.255.255.0 destination 192.168.251.0 255.255.255.0 prefer FW_VLAN3603
clause 30 permit any x.x.158.0 255.255.255.0 destination 192.168.250.0 255.255.255.0 prefer FW_VLAN3603
clause 35 permit any x.x.158.0 255.255.255.0 destination 192.168.0.0 255.255.0.0 prefer FW_VLAN3603
clause 40 permit any x.x.158.0 255.255.255.0 destination 172.16.0.0 255.240.0.0 prefer FW_VLAN3603
acl 10
clause 99 permit any any destination any
apply circuit-(VLAN3605)
apply circuit-(VLAN3603)
apply circuit-(VLAN2421)
apply circuit-(VLAN1)

Port Mapping problem with a Snow Base Station

I wish to enable port mapping with my Airport Snow Base Station. (SBS) I am using an Earthlink Efficient Stream 5667 DSL modem to my SBS. I am running firmware version 4.0.9 and connecting with 10.4.3.
So -- enabling port mapping requires that the IP address on my 10.4.3 computer doesn't change, and that I then map the ports. However, I can not manually assign an IP (say 10.0.1.201) as my 10.4.3 can not connect using either "DHCP with manual address" or "manually" (where the router and subnet mask match the DHCP assignment)
What should I do?

Do not use the "DHCP with manual IP address" - that is a mode not supported by most networking devices on the market.
What you should do: on your Mac, open System Preferences->Network->Show Airport->TCP/IP tab. Select to "configure manually". Then enter the following parameters:
- IP address: 10.0.1.201
- subnet mask: 255.255.255.0
- router/gateway IP: 10.0.1.1
- DNS IP: use either 10.0.1.1, or enter the actual IP address(es) of your ISP's domain name servers

NAT configuration and Port Mapping for xBox

I'm looking for help with port mapping to open up the NAT for an xBox One. I'm working with the following network devices:
xBox One
DSL Modem: Embarq (ZyXEL) 660R series
Airport Extreme version 7.7.3
I understand the following from researching the issue:
The default settings for both devices block the ports needed for xBox Live.
Airport Extremes are not on the compatible list for xBox.
Port Mapping is better then creating a DMZ for the xBox.
The xBox needs its own manually set IP address.
I switched my Network>Router Mode from Off (Bridge Mode) to DHCP and NAT. I then created a DHCP Reservation and the Port Settings for that IP.
After doing this, the Airport would restart and display a warning - Double NAT. I figured this was because the 660 settings showed the NAT Mode to be SUA Only. The Edit Details link displayed an empty table where you edited the SUA/NAT Server Set. I switched from NAT Mode>SUA Only to None. So there was my Double NAT and I would have thought that would have removed one.
I also disabled the Firewall and Enabled the UPnP.
After restarts the Airport continued to display the Double NAT error. However, with the 660's NAT Mode set to None, the Internet was not there. Web browsers and email accounts replied with server not found.
Only with the 660 set to SUA Only and the Airport in Bridge Mode is the Internet accessible. I now have the details for the SUA filled out for the xBox's IP address and ports.
Hypothesis
Since both devices are acting as DHCP servers the port mapping is not working. Rather then have the 660 distribute IP addresses and then having the Airport distribute another range of numbers, I need to have both devices bridge and distribute one range of numbers. Currently the 660 is using the 192.168 range and the Airport is using the 10.0 range.
Am I correct? Any thoughts and suggestions are welcome.

Port forwarding through a double NAT.. is near impossible.. !!
And the xbox is so attuned to using UPNP it is very hard not to.. even port mapping is not a great fix. Since apple decided gamers did not count as users for Airports.. I think honestly it is best to bypass the airport and stick to upnp from the modem router.
What method of authentication does your ISP use? Because it is really better to use one router.
And in fact the router should be the Zyxel. If you plug the Xbox to the Zyxel running in full router mode, with the airport removed from the network does it work and open NAT??
If not replace the Zyxel with a modern listed router that is xbox compatible and bridge the airport to it.

Default Host (DMZ) and Port Mapping together

Hi all,
I have the G5 set as a default host for all my web services through the Airport Extreme.
In the Airport Extreme's Port Mapping tab, a user is not prevented from using the port mapping tab even when the Default host is set. I want to serve video through another port not on the G5.
Does this mean I can set up port mapping for ports I do not want to go to the default host? (my G5 in this case)
I asked this on the airport forum and never got an answer, maybe you G5 folks might know. (Or maybe there is a setting that will redirect from the G5.)
Thanks in advance,
Jamy

I figured it out. I can't have a DMZ and separately port mapping on the Airport.

Airport Port Mapping problems...

I have an AIRPORT EXTREME firmware 7.6.1. I'm trying to get it to open port 443 in port mapping and it says it's open and when I port scan it's not. Am I missing something? Please see the enclosed image...

Hello ,
I have the same troubles got the latetest updates on AE en soft 6.0
i cant get my ports open !
it realy s...cks !!
i spend alreddy more dan 3 days to get it working , whit no results !!
i have 3 foscam Ip cams who doenst work anymore outside my LAN !
i tried to get it work whit 5.6 but than i got huge faillure on my AE drops out and need hard reset !
I hope ther are some techies from apple who can solve this troubles !
HELP HELP HELP HELP HELP
why do the change someting that works before fine !
before the updates everthing works fine
the big boss i passed away Rip
and the house is collapsing !

WRT54G (ver 7)-port forwarding problems (eMule)

Hi I want to use the eMule file sharing program and the problem is I cannot forward any ports (this problem already occured at other programs too) ... Im sure Ive typed in the correct port ranges, and used the correct IP-adress... I tried to use static IP adress, furthermore ive disabled the "Block Anonymous Internet Requests " option, without any success... I cannot find any firmware updates for this version either... pls help

Please open the router configuration interface at http://192.168.1.1/ (or whichever address you use to configure the forwardings). Click on Status on post the full status of your connection.
Also post the exact settings which you use for the port forwardings.
On the computer to which you forward and which is running the emule server, open a command prompt window, enter "ipconfig /all" and "netstat -aon". Post the full output of those two commands as well.
For few more things to check see this Checklist.
Message Edited by gv on 09-04-2007 06:15 PM

Port Mapping Problem

I'm using Filemaker Web Publishing and need to map port 591 to a local computer. I have a static IP address from my ISP but when I enter the info into Airport it doesn't seem to do anything. I've also tried, as a test, to set up personal web sharing and this does not work either. I was successful at setting this up with my old router so I know that this is possible.
I've given my computer a static IP. I've also tried the having Airport reserve an IP address.
Any thoughts?

I'm using Filemaker Web Publishing and need to map port 591 to a local computer. I have a static IP address from my ISP but when I enter the info into Airport it doesn't seem to do anything. I've also tried, as a test, to set up personal web sharing and this does not work either. I was successful at setting this up with my old router so I know that this is possible.
I've given my computer a static IP. I've also tried the having Airport reserve an IP address.
Any thoughts?

N8 and ovi map problem,server timeout

just got my new device and when try to update map application to have maps on the phone I alwys get the following eroor..server timeout...try again...I have tried all evening and same message again and again..I have Ovi suit version 2,2,1,23..It´s a new phone and it´s not working,I have tried on both windows XP and on Windows 7..I have reset the phone many times and if I don´t get this to work fast I will definately have my okd phone back and sell this one,hve read about other phones and they all experience the same problem with the latsest Ovi update...so what will I do???????..any suggestion,tried with version 2.1.1.1 and same problem...It´s a brand new phone and is not working..come on..
Solved!
Go to Solution.

Nokia's solution to update maps is exclusively using OVI Suite.
Ovi Suite is a tremendous piece of software: never checked before any release, always buggy.
You are lucky if you do not need maps because PC Suite is reliable.
You are cursed if you need maps...
Any upgrade of maps ends up in problems!
Today if failed again, I am used to it....
I will stop any use of this Nokia's E72 (it is their product, not mine) as soon as my contract with my provider will end!
My today's provider will also be punished by seeing me away definitively at the same time. And I will get away as many people as possible from Nokia!!!!!!!!!!!!!!!!!!!!!
I hate this product and this company: They are not concerned by their customers, they are just good at taking the money and run away.
That's Ok for me, you will be out of this market within 3 years with such an irrespect of your customers. -10% of market share / year is 0% in 3 years from now on. And, yes, it is too late: You did it again with the N8 (read above)!
Have a nice day!

Firefox 8 and Google Maps problem!

Ever since upgrading to Firefox 8 (I don't recall this problem using firefox 7.01) using maps.google.com if I search for something like watertown, wi or greendale, wi it will work the first time or so. Then afterawhile it will just say "loading" and stop working. This is on Windows XP Pro 32bit.
I have completely re-installed firefox from scratch (deleted all settings) and started over. But, it does the same thing!
Help!

I have this same problem with Firefox 9.0.1, but not with explorer; "problem" = destination and location markers in Google Maps don't appear and hence can't be clicked and dragged, really limiting usefulness. Problem began a few weeks ago, maybe when Firefox updated. Haven't added any new add-ons. Tried opening Firefox in safe mode, tried the add-on posted here, tried the various Tools>Internet Options suggested here, none worked.

Doctype and Port 80 problems

Hi
Have a site up and running through Contribute and hoped
someone can help with a couple of problems:
The index page is adding :80/ to the end of the URL instead
of just / Does anyone know how to get rid of this?
Also, what is the best doctype to use with contribute?
Appears that no doctype is added and really need to do that before
tackling the other code/validation errors. Tried a couple of
options but these made the situation worse.
Thanks in advance for any assistance.
Tom

Hi
I would like to say that not getting a reply in the forum was
a little disappointing. In no way do I blame forum members, that's
up to them but don't Adobe people keep an eye on questions that are
unanswered. Looking at how many others there are, maybe not.
Neither did they reply to the email I sent to support.
In the end, I found a free website help line in the area
where I'm staying. They are
Surrey Web
Development and deserve a mention, as they helped for nothing,
within a couple of hours. Anyway, the port 80 thing I'm still not
sure about, as they spoke to my hosts and this is sorted out but
I'm not sure how. On the doctype, they recommended HTML 4.01
Transitional, I'll paste the code below if that helps anyone, which
goes right at the top of your page (in the source code, not the
page itself).
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01
Transitional//EN"
(Then there's another line, just search for that, went weird
on here.)
They also suggested a few other things and explained how to
use a validator. Can't say the website code is absolutely perfect
yet but nearly. Can't really understand why this isn't added
anyway, I love contribute and people say my website looks good,
important for a photographer. Just hope Adobe will work on the
coding problems, I don't want to feel I have to use something else.

Port Mapping is not working ?

First of all, sorry for my bad english as it is not my primary language.
So my problem is that I play Warcraft 3 and that I would like to host some games. To be able to host, I have to do port mapping for the ports : 6112-6119, which I did in the Airport Utility --> Advanced --> Port Mapping. I did it for every port 6112, 6113, etc. But the thing is that when I go on this website: http://www.whatsmyip.org/ports/games/ (Which is a website that tells me what ports are open on my computer), only port 6112 is open. Ports 6113-6119 are closed. Before my Airport Extreme, I had a Linksys and I had no problems with hosting and port mapping, which means it is not my ISP that is blocking the ports.
Also this is the setup of my internet if it can help. I have an AirPort Extreme wich is connected to the modem in my basement (I did the port mapping on this one) . From this Airport Extreme, I have another Airport Extreme connected to it. I am connected to the second Airport Extreme in bridge mode with ethernet.
I don't know if this was clear or not lol. Anyway I would appreciate any help. Thank You !

This is just a guess, but if you still have that AirPort Extreme, you might plug it in long enough to have AirPort Utility do a File >Export Configuration File, then reconnect the Time Capsule and do a File > Import Configuration File. Once that's done you may have to do a little adjustment to account for the disk drive.

Xbox 360/one problem and port forwarding

For a couple months now (since I got my AirPort Extreme) I have not been able to connect to a certain friend on xbox. I can connect to anybody else however. The only way we can (kind of) connect is if somebody else is host and we both connect to him.
My NAT type is Moderate. When I try to test my connection on my xbox it says that I can connect but I am limited in matchmaking (this is joining games and using voice chat, which is the problem named above for my particular friend). The xbox shows the error and suggests that I enable UPnP or open the port 3074.
The problem is that I have already have! I gave my xbox a static IP and forwarded the port 3074 to that IP.
(I have also tried forwarding all the ports that xbox live uses to the xbox. These being:
Port 88 (UDP)
Port 3074 (UDP and TCP)
Port 53 (UDP and TCP)
Port 80 (TCP)
as found on the xbox website... https://support.xbox.com/en-US/xbox-360/networking/network-ports-used-xbox-live
I made sure to put them in the right text boxes for UDP and TCP so that is not the problem either.)
I know that the AirPort Extreme does not support UPnP but does have a similar thing called NAT Port Mapping Protocol which was already enabled. (I tried all possibilities of enabling/disabling NAT...Protocol and port forwarding/not port forwarding.) --- This is not the solution as I see it
In short: My xbox tells me to open port 3074. I already have. It still tells me to open it and still won't work.
I posted this on the apple discussion page (instead of the xbox discussion page) because I know that it's not an xbox problem. When I had my old linksys router it worked perfectly.

I have this exact same question and problem. I know this doesn't help, but would appreciate any updated information if you find an answer. I'll keep working on this also and let you know if I find an anwer.

WRT54G - IP and Port mapping problems

Similar Messages

Maybe you are looking for