WRT54GS - No Internet when plugged in, but I get Xbox LIVE...

I have Verizon DSL for Internet, and when I switch the Ethernet cable over to the Router, I have no Internet on my computer, but I have Xbox LIVE...?
I'm lost; how do I fix this?

First check the IP when directly connected to the DSL modem in case if its 192.168.1.1 then connect only the computer to the router without the modem connected then change the lan ip of the router to 192.168.2.1 and the power cycle the network i.e. turn off power to modem and router, connect the modem - router - computer, power up the modem wait for the light, followed by the router. This should work. Also make sure that you computer is not set to static IP address.
Start-control panel - network connection - right click local area connection and select properties - tcp/ip properties - It should be set to obtain IP automatically.

Similar Messages

  • When I purchased my iphone and ipad last week they told me I would connect the ipad to the internet through the phone but can get niether the phone nor the ipad to see the internet?

    When I purchased my iphone and ipad last week they told me I would connect the ipad to the internet through the phone but can get niether the phone nor the ipad to see the internet?

    Connecting the iPad to the internet via the iPhone is done by setting up a personal HotSpot, but you have to have that supported by your carrier and have to have established the account to do so.
    On the  iPhone, Settings > General > Network > Set Up Personal Hotspot

  • IPhone 4 registers that it is getting a charge (vibrates when plugged in) but is not charging

    My iPhone 4 registers that it is getting a charge (vibrates when plugged in) but is not charging.  The charging display shows the fully charged symbol and not the charging symbol.  I have tired charging using two different cords and into both my computer and an outlet.

    Thanks Jennifer.  I have done some searching and nothing firm came up.  I have also tried a hard resent, both with it plugged in and without.  I have an appointment at the apple store tomorrow.  I too think a restore or new battery is in my future.  Thanks again! 

  • HT1476 Anyone experience that the phone will not begin charging when plugged in, but must be rebooted while plugged in for phone to begin recharging?

    Anyone experience that the phone will not begin charging when plugged in, but must be rebooted while plugged in for phone to begin recharging?

    Seems like battery is faulty. Make Genius reservation or set up service and take or send to Apple for resolution under Warranty.

  • How can I get my ical events from my iMac to my iPhone? Anything I entered into ical on my iPhone will transfer to ical on iMac when plugged in, but not vice versa.

    How can I get my ical events from my iMac to my iPhone? Anything I entered into ical on my iPhone will transfer to ical on iMac when plugged in, but not vice versa. I think I have changed my iPhone (after looking at similar questions) to iCloud, but it's still not syncing.

    You need to sign into your iCloud account on your Mac, and check the Calendar option. System Preferences>iCloud, sign on your iCloud account, check the apps you want to sync with your device.
    Cheers,
    GB

  • I have a power PC that makes abunch of noise when plugged in but the power light just blinks when I press it and shows no graphics wht is wrong

    I have a power PC that makes abunch of noise when plugged in but the power light just blinks when I press it and shows no graphics wht is wrong

    Click here for information; if the computer beeps three or fewer times, remove and reinsert the computer's RAM. If it beeps four or more times, it needs to be repaired. If it's a G5, it will ignore RAM modules that aren't part of a matching pair.
    (76386)

  • I fitted new battery but it won't charge. when plugged into wall socket gets to itunes setup but no further. when connected to computer not enough battery to turn on to get into setup. Any ideas please?

    i fitted new battery but it won't charge. when plugged into wall socket gets to itunes setup but no further. when connected to computer not enough battery to turn on to get into setup. Any ideas please?

    turnbui wrote:
    i fitted new battery but it won't charge. when plugged into wall socket gets to itunes setup but no further. when connected to computer not enough battery to turn on to get into setup. Any ideas please?
    It sounds very very much like the battery. You will need to have it replaced. If you put the failing one in yourself you will need to pay as your Warranty is now void.
    Pete

  • Can connect to internet when plugged directly into linksys cable modem but

    I have an Airport Extreme router, am running Windows Xp, and can connect to the internet when I plug my laptop directly into my linksys cable modem. I can also connect to the internet when I plug directly into the airport extreme via cat 5 cable. However, when I try to connect wirelessly via airport extreme, I cannot get on the internet, even though it shows I have excellent signal strength on the laptop, have a solid green light on the airport, and all lights look right on the cable modem. It says something about error -6753. This is what I am doing now; I am connected to the airport via cat 5 cable, and am downloading all software / firmware updates for the airport, do you think this will fix my problem? How do I diagnose if my problem is with the wireless settings on the laptop, or with the airport? thanks, this is extremely aggravating.

    Welcome to the discussions forums airporteggstreme.
    I found a couple of posts that may be relevant. They point to the fact that your PC may be looking for a different address when it's connected wirelessly versus its wired connection. I believe you'll solve the problem by making sure both your Airport and your PC are configured to get their IP addresses via DHCP. If all else fails "hard reset" your Airport, unplug your PC's Ethernet cable and set it up wirelessly. That should work.
    Here's the link: http://forums.whirlpool.net.au/forum-replies-archive.cfm/228336.html
    It refers to an Express but the Extreme will be similar. If you scroll way down you'll find the following:
    In order to configure the Airport Express you not only need to connect to it as the access point but *also need to treat it as a DHCP server.*
    If you connect the the AE as a base station but do not have "Obtain IP address automatically" in your network settings you will receive error code -6753. I racked my brain on that for a while after doing a number of hard resets. Once I went into my PC's network settings and removed the manual IP address I had set there (192.168.15.104) and set for automatic ip address retrieval I was able to configure the AE using the admin utility.
    Once you have finished configuring the base station and set it to join your existing network, you can change your PC's IP back to whatever you need for your own purposes.

  • I have a macbook 15 inch and philips LCD which I'm trying to connect my laptop to. I currently have a HDMI plugged in, but am getting an error message "no video input" on the LCD tv. Please help!

    I have a macbook 15 inch (retina display) and philips LCD which I'm trying to connect my laptop to.
    I currently have a HDMI cable plugged in, but am constantly getting an error message "no video input" on the LCD tv.
    I have checked the philips LCD to be in the HDMI mode and googled many threads but have
    not found a solution to solve my problem. Would appreciate any help given!

    Hello, anabelleho. 
    Thank you for visiting Apple Support Communities.
    Here is a troubleshooting article that I would recommend going through when experiencing this issue.
    Apple computers: Troubleshooting issues with video on internal or external displays
    http://support.apple.com/kb/ht1573
    Cheers,
    Jason H.

  • Windows 8.1 freezes when I am sending messages to Xbox Live friends

    When I spend an X amount of time in messages, specifically sending messages to Xbox Live friends, my mouse moves slowly. When that happens my PC crawls to a halt and I cannot exit the app nor can I go back to Desktop. 
    Any solutions?

    Hi,
    A slow system reaction normally because of over use of system memory and high usage of CPU, to confirm this, open the taks manager in this way:
    1.type “task manager” at the search box, open task manager, then click “performance” tag to check the memory and CPU usage by right clicking at the application, then stop this one.
    2.if the usage stands on a high percentage, go to the details tag to stop the applications that cost high resources.
    Besides, I suggest to go to the Xbox site to check the minimum requirement:
    Download speed: 3 megabits per second
    Upload speed: 0.5 megabits per second
    Ping speed:Less than 150 milliseconds
    And other requirements you can find it here to check the details for Xbox:
    http://support.xbox.com/en-US/xbox-360/networking/slow-performance-solution
    Regards
    Wade Liu
    TechNet Community Support

  • Lose internet when plugging into switch

    I am perplexed why I can create a wireless network with my airport extreme and have great internet connectivity through my cable company, but when I plug the airport into a switch to distribute the internet through out my office the internet immediately starts slowing down and eventually completely goes away.  Unplug extreme from switch and the internet comes back for wireless clients.  Problem started about a month ago.  I figured switches were going bad so I replaced every switch in the office.  Did not solve problem. Thought maybe airport extreme was going bad so I replaced it  with latest  airport extreme (cube). Problem still exists.   Nothing has changed in my network configuration in past two years.  No other services that use the network is effected, just internet connectivity.  I was quite ugly with my internet provider thinking it was a service issue until on a whim I unplugged extreme from switch and my iPad, iPhone, and macbook pro were able to connect to the internet wirelessly instantly.  Plug it back into the switch and internet connectivity for wireless and wired goes away.
    Any suggestions are greatly appreciated.

    That's only one explanation, and an oversimplified one at that. In any event I think your best course of action might still require disassembling your network and adding one piece at a time. Assuming your business is closed for the weekend, now might be your best opportunity.
    Short of that, power down all switches, Macs, other devices (though I doubt iPhones, voip phones or printers can contribute to the problem) and the Extreme (no need to reset it). Then, power up the Extreme and one Mac that is connected through a switch. Turn Wi-Fi "off" to ensure Ethernet is its only viable network connection, as well as for troubleshooting simplicity.
    It should have no connection until you power up that switch. Do that, and determine if the problem still exists.
    Assuming it doesn't, turn its Wi-Fi back "on" and test.
    The iPhones and iPads should also be working at this point.
    Proceed to the next Mac and test the same way. If it's connected to a different switch, power it on also, then re-check the first Mac.

  • WRT54GS - Slow internet when hooked up

    Hi all....I have a WRT54GS (seems to be a popular unit with some issues) and here is my thing:
    I hooked it up about two months ago and had no problems with it. Last week, I started having slow internet connections when the router was hooked up. I ran the cable modem straight to the PC and it was fine. I just hooked up the router again and it was horribly slow. I used testmy.net to test my speeds and my download time was about 143 times faster WITHOUT the router (with speedbooster, no less). The only thing I've done is to do a firmware upgrade to the most current version and the major problems began. I checked my setting and they all seem fine.
    Does anyone have any ideas? Unfortunately I did not save a copy of the configuration before upgrading. Thanks....

    Thanks for the help.
    Here is what I have so far:
    1. ISP is Time Warner Cable, and I am not sure of what I was setup for, but my internet connection icon in my system tray shows 100 Mbps.
    2.  The modem doesn't have a name brand on it that I can find, but the model is 60194E-A02. Google says it is an Ambit modem.
    3.  I used testmy.net for some tests last week and here is what I got (using my laptop):
          a.  Wired to modem directly  - download speed 773 kbps, connection 6.33 Mbps; upload speed 18kbps, connection 0.1 Mbps
          b. Using router - connection was so slow it times out.
    So I hooked it to my desktop PC, and ran the tests:
          a. Direct to modem:
    Download Connection is:: 7155 Kbps about 7.16 Mbps (tested with 12160 kB)
    Download Speed is:: 873 kB/s
    Upload Connection is:: 162 Kbps about 0.2 Mbps (tested with 386 kB)
    Upload Speed is:: 20 kB/s
         b.  Using router:
    Download Connection is:: 45 Kbps about 0.05 Mbps (tested with 97 kB)
    Download Speed is:: 5 kB/s
    Upload Connection is:: 17 Kbps about 0 Mbps (tested with 97 kB)
    Upload Speed is:: 2 kB/s
    Only other thing I can think of is that I put the new modem beside the router. Earlier today I put the modem back where it was, about three feet away. It actually seems to have helped. Is there a true phenomenon when the units are side-by-side?
    Thanks...Rick Ferguson
    Message Edited by  Rick Ferguson on 07-30-2007 02:27 PM
    Message Edited by   on 07-30-2007 02:28 PM

  • Jst got new computer and want to make it my main i-tunes for i-pod. It shows up when plugged in but it won't stay in the computers music library so when unplugged theres no music. Does it have to do with homesharing? How do I move orig stuff to new comp?

    I just downloaded i-tunes on my new computer because I want this one to be my main computer used with my i-pod. When I plug in my i-pod mine shows up, but my music and all my previous purchases aren't in the new computer so when I unplug my i-pod everything goes away and there is nothing. I am wondering how I get all of my original music and purchases that are on the other computer I was using with my i-pod onto this new computer. That way it shows up even if I don't plug my i-pod in. Does it have to do with homesharing? I have it on, do I need to turn it off from the main computer? I just everything in this computers i-tunes music library, not just my i-pods music when it's plugged in. Can someone please help, I don't know why this is so difficult.

    I am wondering how I get all of my original music and purchases that are on the other computer I was using with my i-pod onto this new computer.
    Try the iTunes for Windows forum area.

  • Battery indicator showing fully charged when plugged in but battery percentage is not

    I've had the iPhone 5 for about 6 months now and starting about a week ago the battery started messing up.  I plug in my phone to charge and the indicator at the top right shows the fully charged indicator when the battery percentage is clearly not 100%.  Randomly it will switch to the charging indicator and actually charge but otherwise it stays like that and just continues to lose battery while it is plugged in.  I've tried my friend's charger and it still does the same thing so it's not the charger that is malfunctioning. 

    Seems like battery is faulty. Make Genius reservation or set up service and take or send to Apple for resolution under Warranty.

  • Red light glows when plugged in, but device wont respond

    I've had the red Curve for nearly a year now. Today I accidentally knocked it off of my desk onto the carpet. It was not a hard fall, but when I picked the device up it seemed to have turned off. It would not turn back on viathe power button, so I attempted tor emove the battery. As I struggled with the back of the device, it seemed to start working again. I got the white screen with the hourglass that usually comes with the reinsertion of the battery. However, when I finally removed the battery and put it back in, the device would not respond. I plugged it in to the AC charger and the light glowed red for a few seconds, but the phone did not respond otherwise. Every time I unplug it and plug it back in, the red light glows but nothing else happens. I tried putting in a different battery but it didn't help. Can anyone tell me what is wrong with my blackberry? do I need to simply leave it plugged in?

    it's black. There seems to be nothing wrong with it except that the light turns red when I plug it in and it simply wont respond when I press buttons. There is nothing rattling inside and nothing seems broken at all. I heard that when phones are dropped, they may lose their battery power. Does this happen? If this is what happened, shouldn't the light then be green?

Maybe you are looking for

  • Oracle Financials AP 11i tables Vs R12 tables

    Hello, I have a package that works in Oracle Apps 11i instance. This package is using 11i tables in its cursors. we are moving this package to r12 and thus this package has to run in r12 using r12 tables. I have heard that a lot of tables have been c

  • Set rating stars

    This question was posted in response to the following article: http://help.adobe.com/en_US/lightroom/using/WS11A1E98C-3D8D-47b5-8335-4B9D8C3A5D36.html

  • ToolBoxTools.addEventListener only works every second time

    Hi! Our layouts pretty often click on the "page tool" by mistake and it happened a few times, that they changes the size of the page without even noticing. Because there is no way to remove the tool from the toolbar (I guess?), I wanted to write a sc

  • Art on Podcast Page but Not Search Results

    Podcast art shows up fine on my iTunes podcast home page, but only the generic podcast art shows on an iTunes search results page. From my brief research (clicking on other generic podcast art in search results), this problem seems unique to my podca

  • Sending a slideshow via email in Photoshop Elements 10-how do you do it and have it come out good?

    I made a slide show, and under properties, chose size to share via email, then attached it to an email.  I viewed it, and boy was it crappy!  All out of focus and broken up.  How do you create a slideshow for email sizing and have it come out like th