WRV210 loses port forwarding settings after reboot

Along with wireless problems that have already been documented about this device I am having problems with port forwarding where it will lose all its settings after losing its power. I then try to go into the management for port forwarding and am not able to put the settings back in as every time I hit 'Save' it just loads the page back up with no settings applied. Another strange thing is that the protocol comboboxes only have options for UDP or Both.
I then reapply the latest firmware and am able to enter the settings again.
Any help would be greatly appreciated as I'm at my wits end with this one.
Thanks,
Paul

Dear Paul,
Thank you for reaching the Small Business Support Community.
If you are already running the latest firmware release version 2.0.1.5, all I can suggest you is to contact the Small Business Support Center directly to determine if this is a hardware related problem, notice this product is already End of Life/End of Support and therefore the support is subject to warranty or contract terms and conditions;
https://supportforums.cisco.com/community/netpro/small-business/sbcountrysupport
Please do not hesitate to reach me back if there is any further assistance I may help you with in the meantime.
Kind regards,
Jeffrey Rodriguez S. .:|:.:|:.
Cisco Customer Support Engineer
*Please rate the Post so other will know when an answer has been found.

Similar Messages

Airport Extreme removes port forward settings every reboot

I have set up various port forward settings on my Airport Extreme from OS X Server. However, every time I reboot the Airport, all port forward settings are lost except Contacts, Calendars, and DNS. It gets very troublesome to constantly readd all my settings in there. Port forwards are the only settings that are lost.
Please help!

I found the issue – and it's fairly simple and obviously really. I'm guessing you were adding the ports from OS X Server in the order they are listed within Server.app (where they are listed in alphabetical order). After Calendar, Contacts and DNS is "File Sharing".
If this is enabled, whilst File Sharing is enabled on the AirPort Extreme, the port forwarding entry for File Sharing, and anything below is removed.
Simply disable "File Sharing" from AirPort Utility before continuing (as recommended by Server.app when setting up the service for File Sharing).
I understand you replaced your AE and no longer have the issue – I thought I'd leave the explanation should others encounter it.

Port Forwarding Persists After Deleting Entry/Reboot

I had ports 80 and 8080 forwarded to my file server that is static @ 192.168.1.51 for a brief time.    I removed the entries in my airport extreme. It restarted and came up green. The file server has a software firewall that was turned on over the weekend.   I received flags that inbound requests on 80 and 8080 were being rejected.
Confused, I looked at the port forwarding settings in the airport extreme and the entries were gone.   I then power cycled the airport.   The inbound request alerts continued on 192.168.1.52
If the port forwarding entry was removed, I wouldn't expect the server to see any more inbound requests.   This is confusing me.    Any thoughts?
Thanks,
Jerold

I havent't had any responses so I am going to document my steps here.   Maybe someone else will benefit.
I ran shields up (https://www.grc.com/x/ne.dll?bh0bkyd2) to see if the ports were open and they all showed stealth except for port 21.   I did not have port 21 forwarded, but did at one time.   It acts like the airport extreme is not writing/updating the port forwarding table as it is changed.    Ports 80 and 8080 were stealth.    The file surver had upnp on, so I turned that off, but the airport still seems to pass incoming requests to the file server.   They are not responded to, but I get email alerts about the intrusion attempt.
I thought the router was supposed to block these incoming requests.   Why would it be forwarding it to the internal ip and alerting the file server firewall?

E3200 not saving port forwarding settings

I have tried numerious times to set my port forwarding settings. Everytime I setup and fill in the appropiate ports and hit the save button my setting are lost. I go back into the port forwarding setting page and literally after a fews secondsof inputting the ports and nothing is there and everything is zeroed out . Has anyone experienced this problem. Do I have to set my ip address to static before I can put my port forwarding settings in.

Yes to all.
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

I need help changing settings (port forward?) after a physical server move

Hi! I have a 10.6 server that I use at home. All is well and good there. The Airport Extreme assigns IP addresses for the network. I have www.mydomain.com that runs on the server -- I use it for testing web apps, etc. I use DynDNS with their client app that send the Comcast dynamic IP address back to DynDNS to keep the server on the grid.
My friend has a 10.6 server. He has www.hisdomain.com as a home business. He also uses DynDNS in a similar way. His landlord just informed him that his apartment is going to be sold from underneath him and he has to move ASAP. It looks like he won't have a permanent place for a month or two, so I offered to let him keep his server at my place.
We both run websites on port 443 and port 80.
After attaching his server to my network, his domain name updates, but typing www.hisdomain.com into a browser lands me on www.mydomain.com. I guess that the problem is port forwarding... the router sends all 443 and 80 requests to my server.
How do I configure this so that services for hisdomain.com are forwarded to his server while services for mydomain.com are forwarded to my server?

Short answer: you can't, although there are a couple of ways to sort-of kluge it.
Long answer: When your router gets an incoming connection, the only thing it has to go on is the IP address and port number (the domain name is sent much later, after TCP session with the server is established). So unless you have multiple public IP addresses (and a router that can handle them), or want to put the sites on different ports...
Speaking of which, here's kluge #1: run his server on different ports (e.g. 81 and 444, or maybe 8080 and 8043) and set the router to forward them to his server. Problem: the user has to include the port number in the URL when they connect, or they'll get your server.
Partial solution (and kluge #2): add a virtual site on your server, with the hostname www.hisdomain.com, go to its Aliases section, and add a rule in the URL Aliases & Redirects section, with these settings:
Type: RedirectMatch
Pattern: (.*)$
Path: http://www.hisdomain.com:81$1
Then build an SSL version that redirects to https://www.hisdomain.com:444$1. Problem: when the client connects, they'll get your SSL certificate instead of his (again, it happens before the client sends the domain name it's trying to reach), and get a cert error. No fix for this.
Kluge #3: instead of making the virtual site redirect clients to his server, add a reverse proxy so your server'll transparently forward requests to his server, and proxy the replies. I haven't done this, but I think what you need to do is make a virtual site (as above), and under its Proxy tab (the one under the virtual site, not the one under the Settings section), check the Enable Reverse Proxy box, leave the Proxy Path as "/" and the Sticky Session Identifier field blank, and add a Balancer member with the Server URL "http://hisinternalipaddress" and a blank Route. Or something like that. Again, you could do the same for https as well, but you'll have the same certificate problem.

Mavericks "forgetting" simple settings after reboot

After upgrading to Mavericks I was surprised by the the new wave background image on all my spaces - while it is a lovely picture I use the background as a clue to which space I'm in, so I reset them to my own pictures/images as they were prior to the upgrade.
After rebooting the images returned to the wave on all spaces - huh, that's weird... So I reset them.
I also noticed I had an AppleScript app that wasn't working right and I need to debug, so I turned off the "Open at Login" option for the app and went about my business.
I rebooted again later in the day and once again my desktop images were reset and the AppleScript app was launched at login.
What am I missing that Mavericks is forgetting these customization settings?

I was having the same issue with background images. Every time I restarted, back to the waves...
I've since placed in the image in Library>Desktop Pictures and changed the image through preferences. So far it's been holding (fingers crossed). Previously I had been using the Contextual Menu>Services>Set as Background Image to do it.
There is also another way. Navigate to System>Library>CoreServices>DefaultDesktop.jpg.
You'll see it's an alias to the Waves, background. In this case, just create a new alias with the correct privileges and the same name that points to your desired photo. You may have to do this as the root user.
Lot's of trouble for a simple thing, hopefully it gets fixed.

RV180W loses port forwarding rules when switching WAN connections

We have a backup WAN connection in our office, but we switch this connection manually on our RV180W when the primary goes down. Our normal connection is ADSL with PPPoE, and the backup is Cable with DHCP.
However, we also have some port forwarding rules for our VoIP PBX (UDP port 5060) as well as SSH, and these rules seem to stop working completely when we switch our WAN connection to our cable connection. We can still surf the web from our workstations, but our incoming phone calls and SSH connections all cease to work completely. The problem does not persist after we've switched back to our normal ADSL connection.
This behaviour is completely bizarre and suggests that there's some kind of bug in the Cisco RV180W.

helm,
I'm sorry, I wasn't clear which IP address renewal I am speaking about.
I believe that the problem is caused when the router renews the WHS's local IP address (192.168...). My WAN IP address remains unchanged througout the tests I performed and the problems I experienced.
The very act of changing the local clients' lease time in the router's configuration causes the forwarding to be lost immediately. (I am gusessing that when the lease time is changed, the router immediately renews the lease and begins a new countdown.)
(In fact, I might go as far as to say it is a bug in the firmware, but I haven't done enough testing to nail it down.)

Port forwarding settings don't last

Hi I have a synology NAS I set up the port forwarding and all worked fine, confirmed open port 80, all OK
All settings within home hub 2 have not been changed but now the NAS does not respond, and port 80 can no longer be seen any ideas please

There is a guide here.
Port forwarding problems
I assume that you are using a DDNS service to update your IP address, and you have manually configured a static IP address for the device on your LAN?
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

Help please, with port forwarding settings

I have an MSI RG60 wireless router (Ethernet hard wired to my XP Home PC) and don't know what settings to use for port forwarding, to enable my WinMX and BitTorrent clients to work successfully.
I have the port numbers, and assume that this information goes in the Service Port box, i.e. 6699, or 6881-6889.
I know which ports are TCP and which are UDP, but I don't know what IP address to enter or which Common Service Port type to choose. Can anyone help please?
I'm pretty sure that other settings in my PC are OK as I have successfully been running a Belkin router for a couple of years, and have only replaced it with the new MSI unit due to reliability problems.

It does indeed have port triggering, but it wants incoming and trigger port protocol info, along with trigger and incoming port numbers.
How can I type ipconfig into either of teh clients...WinMx or Bit Torrent?

Cannot save Port Forwarding Settings

I have a Wireless-N Home Router WRT150N (firmware upgraded to v1.01.9 ).
When I try to set Port forwarding, I get the screen "Settings are successful. Continue". When I click Continue, the Port forwarding page comes back with empty fields, like if I did not enter anything. I tried to reset the Router twice. No result.
The same thing happens for Port Range and Single Port forwarding... Impossible to save any settings in there...
Any suggestion welcome...

Correction: caching was not the problem.
The problem was that before posting on this forum, I did not enter a existing IP for destination (left the default 192.168.1.0. What got me confused is that the Linksys interface comes up with a message saying that the settings have been successfully updated, even though nothing was done for lack of an existing destination IP, hence the virgin table served back.
I think Linksys should revise the GUY to alert the user when the destination IP is not properly set rather than pretending to have registered a new non functional setting.
Message Edited by lou_boumian on 01-12-2008 10:15 PM

Messaging and Social Networking Widgets Losing Settings After Reboot...

I'm having problems with my Messaging and Social Networking Widgets losing all of their settings after a reboot (power off/on).
Is anyone else seeing this? Is there a fix for this issue?

Try doing a phone reset by removing your battery for 5 seconds then place it back in and power your phone on. You may have to add the settings back. For more information on widget settings click here http://motorola-global-portal.custhelp.com/app/answers/detail/a_id/48507/kw/widget%20settings/p/30,6720,7500,/session/L3NpZC9BN0VVdzY3aw%3D%3D. Hope this helps!

WRT160Nv3 port forwarding settings not being saved

Hello there.
I am using a WRT160Nv3 router and am having trouble getting port forwarding to work.
Specifically, my settings are not being saved properly.
I am trying to set up a server to run for Minecraft, and I have eliminated all issues save port forwarding.
I open up the router's settings by going to 10.10.10.1 in my browser. I go to "Single Port Forwarding." I then choose a blank spot on the left and label the application (in this case, Minecraft), then I type in the ports I want to forward (minecraft uses 25565). I check the box "Enabled." Then I go down to the "Save Settings" button below and click it.
This brings me to a mostly black screen with a white box in it, and big black letters saying "Settings are successful" and a button to click, labeled "continue." I click this, and it returns me to the last page I was on (Single Port Forwarding).
But here is the problem- that page is EXACTLY the same as when I began. None of what I typed in or changed is actually saved on the screen o_0
This definitely baffles me, as it seems as if I did nothing in first place. I use the program whose port I wanted to forward and it still doesn't work, the error messages being the same as always.
So what is the matter here? Why aren't my settings being saved properly? Do I need to get a new router-this one is only a year old...
Any ideas?
PS- I also tried to do port range forwarding, and the same thing happens there too.

hi there and welcome to the forums!
try to clear your browsers' cache..and delete cookies then try again

HP Webcam for Pavilion dv6-1216er dont save settings after reboot

I have some problem from begining use my laptop. Still have this problem after reboot (or but it sleep) i have to put setting on webcam again. I reinstalled everything but this all dont help.

DJuNHP
I would recommend that you reinstall your audio drivers for your HP Pavilion dv6-7029wm Entertainment Notebook PC. I am linking you to the driver page for your PC below. Simply choose your operating system and click next than download your audio drivers and reinstall them.
HP Pavilion dv6-7029wm Entertainment Notebook PC Drivers
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?cc=us&lc=en&dlc=en&product=5272093
If you have any further questions or concerns please feel free to re-post.
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

Nokia 6288 doesn't retain settings after reboot

Hi, i've a problem with a Nokia 6288 that after each reboot
does not retain settings regarding "Normal" profile and background. If i turn off the phone, when i turn it back on it reverts to blank backround and "nokia tune" ringtone and all other settings to default.
I already tried to reset it to factory default but had no luck.
Also tried reflashing firmware with nokia software updater but the problem still remains.
There is a way for "hard resetting" it to factory default?
Regards
Luca

A nokia care point can hard reset a series 40 phone, you cannot do it yourself. They will also be able to fix your problem.
Care points:
UK
http://www.nokia.co.uk/A4228006
Europe:
http://europe.nokia.com/A4388379
Elsewhere:
http://www.nokia.com and select your country.

Safari 5.0.5 OSX not remembering cookie settings after reboot

Hi everyone,
I'm having a very frustrating issue lately with Safari 5.0.5 on my MBP with OSX 10.6.7...
I want to have my cookie settings under Preferences -> Security -> Accept Cookies to permanently be "Only from sites I visit". When I started Safari, and set that setting, it will remember the setting for the entire machines' session. However, if I reboot, or shutdown/restart my Mac, it will revert to the Always setting.
I have tried trashing the Safari plist file under ~/Library/Preferences/, and trashing the associated caches.db file as well, hence resetting Safari, with no success.
Any advice on this would be greatly appreaciated!
Cheers

Hi Andy,
I just tried to temporarily remove Safari Cookies, and I'm sad to say the old issue re-occured as soon as the add-on gets uninstalled.
It seems also, that after launching Safari for the first time after a reboot and going into Safari Preferences fast enough before the add-on launches, the setting is still incorrect, but then gets modified by Safari Cookies.
I went and checked my Login Items, but there's nothing there that can affect Safari; the list hasn't changed in a long time. I don't have folders .../InputManagers or .../ScriptingAdditions under Home/Library.
Under .../LaunchAgents, I have the following:
com.adobe.AAM.Updater-1.0.plist
com.adobe.ARM.df0ab5bbe6f698196fcc21e3c1e66dcb758bd911f4d637272d9d8109.plist
com.apple.CSConfigDotMacCert-<blocked>-SharedServices.Agent.plist
com.apple.FolderActions.enabled.plist
com.apple.FolderActions.folders.plist
com.apple.FTMonitor.plist
com.apple.imagent.plist
com.apple.marcoagent.plist
com.google.GoogleContactSyncAgent.plist
com.google.keystone.agent.plist
`
The first three are related to my Adobe CS5 and Acrobat X Pro installations.
Now that I have the add-on which seems to keep things in check, this isn't as high a priority as it was, but I would definitely love to find out what's causing this so I can eventually nip it in the butt!
Cheers

WRV210 loses port forwarding settings after reboot

Similar Messages

Maybe you are looking for