X-fi Extreme Gamers not in IRQ list, doesn't work at all.

9X-fi Extreme Gamers not in IRQ list, doesn't work at all.O Lo mates,
my specs:
Intel C2D E8500
Gigabyte GA-EP45-DS3R
Club3D ATi 4870 52MB
2GB OCZ
2 WD Raptors connected to onboard raid controller
X-Fi in PCI slot
my problem:
The X-fi isn't working as it should. It's not getting detected in bios / POST so it can ofcourse not be working in any OS (currently running Win7 7068
I used to own a AMD 2500 / Asus A7N8X-E deluxe, and it used to work, but when I upgraded to a C2D E6600 / DFI Infinity it only showed up 3 times in my IRQ list / OS. This ofcourse is to blame to Creative, because they dont care about the PCI standard and didn't implement IRQ resource sharing in the Extreme Gamer card. After upgrading to my current setup (listed above) it's still not working at all, even though I tried disabling all onboard devices I dont use, and manually mapped IRQ channels to the PCI ports so they wouldnt share.
The X-fi is fine, I recently put it in another pc with another brand motherboard, and it was detected instantly. Guess the guy who owns that pc had some luck with his motherboard don't feeling the need to share IRQ's at that particulair moment... its like Russian roulette.
Is there anything i can do to get the soundcard to work even though it doesn't implement the PCI standards and therefore in my opinion failed as a soundcard and as a brand as a whole?
Greats,
eXistenZ
Message Edited by existenZNL on 06-24-2009 02:34 PMMessage Edited by existenZNL on 06-24-2009 02:35 [email protected]

= Hey mate:
Havent seen your exact bios, but if you have a setting in it, called? reset [color="#000080" size="3">Extended System Configuration Data.
Then that might shuffle your bios, per se and then let that card be redetected. I used to use that on my systems when swapping one single part in order to get all the IRQs to shuffle around again, and give one to my card. Do you remember when the magic number to give to your Creative card was IRQ 5, DMA Low of , DMA High of 5, address of 220 and port of 330? Well that is how I used to get my system to shuffle my printer ports and modems in order to bump that sound card to get the correct addresses. Also check to see if the edges of your sound card are blackened. Wipe them with your fingers and see if there is an ashy burned residue. This will tell you if that card has been electrically damaged, or oily/dirty. Also the backlplates on some sound cards are slightly bent and your sound card will fit into its slot, but not all the way. A hair off and that card will be picked by your system every couple of boots.
Try this and let me know how it goes for you.

Similar Messages

How do I get Mac OSX 10.6.4 to print to a Canon iRC2380 colour printer? Using the driver in the Mac's list doesn't work., How do I get Mac OSX 10.6.4 to print to A Canon iRC2380 colour printer? Using the driver in the Mac's list doesn't work.

How do I get Mac OSX 10.6.4 to print to a Canon iRC2380 colour printer? Using the driver in the Mac's list doesn't work., How do I get Mac OSX 10.6.4 to print to A Canon iRC2380 colour printer? Using the driver in the Mac's list doesn't work.

Not sure which driver you mean when you say "the driver in the Mac's list". Apple does not provide a driver for this device, so if you mean one of the default printers that are included with 10.6, like the Generic Postscript or Generic PCL, then these will only work if the optional PS or PCL print kits were installed in the machine. Given your inability to print then it would seem that you have neither kit installed. So this would require you to install the Canon UFR2 driver, which you can obtain via this link.
With the UFR2 driver installed, you add the printer using IP > LPD. Enter the IP address of the iRC2380, leave the Queue name blank and change the Name to iRC2380. Leave the Location field blank and in the Print Using menu, browse to the "Canon iR C2380/2550 UFR II (UK)". Click OK and then Add to complete the queue creation. You should now be able to print. Please reply if it does not work.

I've bought an app called WhatsApp but I was not told that app doesn't work for ipod. So I would like to know how to turn back and get my money back.

I've bought an app called WhatsApp but I was not told that app doesn't work for ipod. So I would like to know how to turn back and get my money back.

Did you fail to look at the requirements before purchasing?
All sales are final. You can try contacting itunes support and asking for an exception

I have a MacBook Pro bought in dec 2009. Currently has mountain lion osx installed. Worked like a dream until today. Randomly froze, so I restarted it. To find I got a grey screen. It wouldn't start. Also note my DVD drive doesn't work, but mountain lion

I have a MacBook Pro bought in dec 2009. Currently has mountain lion osx installed. Worked like a dream until today. Randomly froze, so I restarted it. To find I got a grey screen. It wouldn't start. Also note my DVD drive doesn't work, but mountain lion was installed via App Store anyway.
So here's what I done so far:
tried resetting PRAM - No success
Done disk utility. Disk verified with no errors. I even re formatted disk. - no success starting.
Tried re installing mountain lion via download . It froze halfway installing -no success.
Tried backing up a time machine backup from my USB hard drive. It froze at 1% - no success
Tried booting from safe mode - no success
Tried the command line boot - no success.
Please someone help!

Sounds like the hard dre has left the building, Died, in the Sh*tter, Gone to the hard drive resting place in the sky.
Buy a new drive connect it to the system with a SATA to USB adapter and see if you can install Mt Lion on that drive connected externally. If you can then the drive inside your system has failed.
Oh Wait!!!! You have the 2009 model. They are known for bad drive to logic board cables. So it may not be the drive itself but the cable going from the drive to the logic board. Do the same as above then if the system runs OK with the new drive connected externally install it in the system and see if it boots. If it does you are good to go. If it doesn't then it is more then likely the cable that hs failed.
I would suggest you also SAVE a copy of that download of Mt Lion and create a USB install drive from it using Lion Disk Maker, once you get your system up and running.

Cascading Select List Doesn't work properly

I am trying to use Cascading Select List in My Application. It works for the first time when I run the page afterwards when I try to open the same page in a different window it doesn't work afterwards it doesn't work at all.My code is as follows.
1) Application Process with name getDet
DECLARE
lv_os_List varchar2(32000) := '';
platform varchar2(50);
err_code number;
err_msg varchar2(200);
BEGIN
owa_util.mime_header('text/xml', FALSE );
htp.p('Cache-Control: no-cache');
htp.p('Pragma: no-cache');
owa_util.http_header_close;
htp.prn('<select>');
HTP.prn ('<option value="' || 1 || '">' || '- All OS -' || '</option>');
select platform into platform from platform where platformid =:P139_PLATFORM;
if platform = 'Sun SPARC' then
for i in (select os , osid from ostype where os like '%Sola%' order by os) loop
htp.prn('<option value="' || i.osid || '">' || i.os || '</option>');
end loop;
ELSIF (platform ='Linux (x86 & x86-64)') then
for i in (select os ,osid from ostype where os like '%Linux%' or os like '%RH%' or os like '%SLES%' or os like '%OEL%' order by os) loop
htp.prn('<option value="' || i.osid || '">' || i.os || '</option>');
end loop;
ELSIF (platform ='TRU64') then
for i in (select os ,osid from ostype where os like '%Tru64%' order by os) loop
htp.prn('<option value="' || i.osid || '">' || i.os || '</option>');
end loop;
ELSIF (platform ='Windows') then
for i in (select os ,osid from ostype where os like '%Windows%' order by os) loop
htp.prn('<option value="' || i.osid || '">' || i.os || '</option>');
end loop;
ELSIF (platform ='IBM Linux on Power') then
for i in (select os ,osid from ostype where os like '%Linux%' or os like '%RH%' or os like '%SLES%' or os like '%OEL%' order by os) loop
htp.prn('<option value="' || i.osid || '">' || i.os || '</option>');
end loop;
ELSIF (platform ='IBM System z') then
for i in (select os ,osid from ostype where os like '%Linux%' or os like '%RH%' or os like '%SLES%' or os like '%OEL%' order by os) loop
htp.prn('<option value="' || i.osid || '">' || i.os || '</option>');
end loop;
ELSIF (platform like 'HP%') then
for i in (select os ,osid from ostype where os like '%HP%' order by os) loop
htp.prn('<option value="' || i.osid || '">' || i.os || '</option>');
end loop;
ELSIF (platform ='Itanium') then
for i in (select os ,osid from ostype where os like '%HP%' or (os like '%Windows%' and osid <> 201) or os like '%Linux%64%' or os like '%RH%64%'
order by os) loop
htp.prn('<option value="' || i.osid || '">' || i.os || '</option>');
end loop;
ELSIF (platform ='AIX') then
for i in (select os ,osid from ostype where os like '%AIX%' order by os) loop
htp.prn('<option value="' || i.osid || '">' || i.os || '</option>');
end loop;
ELSE
for i in (select os ,osid from ostype order by os) loop
htp.prn('<option value="' || i.osid || '">' || i.os || '</option>');
end loop;
END IF;
htp.prn('</select>');
EXCEPTION
WHEN OTHERS THEN
err_code := SQLCODE;
err_msg := substr(SQLERRM, 1, 200);
INSERT INTO ERROR_TABLE (error_number, error_message)
VALUES (err_code, err_msg);
END;
2) Application Item
CASCADING_SELECTLIST_ITEM_1
3) In the Footer of the region which contains the items the following Java Script
<script>
function get_select_list_xml(pThis,pSelect){
var l_Return = null;
var l_Select = html_GetElement(pSelect);
var get = new htmldb_Get(null,html_GetElement('pFlowId').value,
'APPLICATION_PROCESS=getDet',0);
get.add('CASCADING_SELECTLIST_ITEM_1',pThis.value);
gReturn = get.get('XML');
if(gReturn && l_Select){
var l_Count = gReturn.getElementsByTagName("option").length;
l_Select.length = 0;
for(var i=0;i<l_Count;i++){
var l_Opt_Xml = gReturn.getElementsByTagName("option");
appendToSelect(l_Select, l_Opt_Xml.getAttribute('value'),
l_Opt_Xml.firstChild.nodeValue)
get = null;
function appendToSelect(pSelect, pValue, pContent) {
var l_Opt = document.createElement("option");
l_Opt.value = pValue;
if(document.all){
pSelect.options.add(l_Opt);
l_Opt.innerText = pContent;
}else{
l_Opt.appendChild(document.createTextNode(pContent));
pSelect.appendChild(l_Opt);
</script>
<script>
get_select_list_xml($x('P139_PLATFORM'),'P139_OS');
</script>
For the first Select list form element properties
onchange="get_select_list_xml(this,'P139_OS')"
Please let me know what change I need to make in the code.

Vikas,
Is your page 0 a public page or it requires authentication? I remember having the same
problem a while ago.
Denes Kubicek
http://deneskubicek.blogspot.com/
http://www.opal-consulting.de/apex/f?p=107:7
http://htmldb.oracle.com/pls/otn/f?p=31517:1
-------------------------------------------------------------------

[SOLVED]Custom DSDT not loading - OEM battery doesn't work - Sony Vaio

EDITING ORIGINAL POST TO POST SOLUTION so I don't do a massive bump
Installed windows and ran the BIOS flasher that came with the battery. Didn't work until I changed a line in the plaintext configuration file (config.ini or something) it comes with. Changed "Capacity: 20" to "Capacity: -10". This changed the battery charge requirement from 20% to negative ten percent (any negative number will do), allowing the program to run and flash the BIOS. Didn't realize I could do that, but it fixed the problem 100%.
#### BEGIN ORIGINAL POST: ################################
Hey guys,
I'm a bit of a linux noob, but I've spent many hours this week trying to fix this issue on my own and have learned a lot about making custom kernels, hardware stuff, ACPI, and ABS. However, nothing I've done has worked and I've hit a wall. For reference, I'm on a Sony Vaio VGN-FZ4000 with linux-3.0 base kernel, gnome3/gdm. The battery is made in china and doesn't list a manufacturer, just model number BPS8, 52000mAh.
[Backstory]
So I recently got an OEM battery to replace the broken original, which hasn't worked since before I installed arch (though it worked with an Arch install I did a couple years ago). When I first plugged it in, the gnome battery symbol popped up listing the battery at 0% with an exclamation icon. I unplugged from AC power and the laptop still ran, but the battery monitor just said it was at 0% and 'Estimating' remaining time. I figured this was a glitch with gnome or just because it was this battery's first cycle so I let it run down until it hard-crashed. Then I plugged back into AC and tried to turn on the computer, but it wouldn't do anything until I removed the battery.
Looking into the problem I discovered this was due to the ACPI firmware table DSDT being compiled for Windows, which has, shall we say, fewer restrictions on sanity than the Intel ASL compiler used for UNIX systems. Sure enough I extracted /sys/firmware/acpi/tables/DSDT to find that its section about the battery contained the entry 'Zero' for Battery Technology, which translates to "non-rechargeable", rather than 'One', which makes it chargeable. acpitool confirmed this; my system thought the battery was non-rechargeable and was constantly discharging it. Needless to say I've only been putting it in temporarily to test solutions since.
[/backstory]
[tl;dr] DSDT firmware contains malformed battery description, now I can't get my system to run with a custom DSDT. [/tl;dr]
Attempted solutions:
[1]
Extract, modify, recompile DSDT and include it with the kernel compilation .config options
CONIFG_ACPI_CUSTOM_DSDT=y
CONFIG_ACPI_CUSTOM_DSDT_FILE="/usr/src/custom_dsdt.hex
CONIFG_STANDALONE=n
as suggested here, a page linked to by the arch wiki page on DSDT.
I followed the instructions but no matter what this has generated errors during the kernel compilation, sometimes due to every line containing unexpected \231 (or other numbers) characters, sometimes finding some error in the DSDT file and then claiming that the driver it was compiling (ol.c somewhere in the drivers/acpi section I believe) had references to undefined functions all over the place. I CANNOT compile with a custom DSDT specified.
[2]
Place recompiled DSDT in /lib/initcpio/custom.dsdt and add 'dsdt' to the HOOKS in mkinitcpio (and rebuild the initramfs-linux-*.img, of course). Another version of this included recompiling the kernel with CONFIG_STANDALONE disabled.
In neither of these situations has the running DSDT ever been anything but the BIOS-supplied one and not once has the battery shown any different behavior.
acpitool and $ cat /proc/acpi/battery/BAT0/info have consistently claimed the information specified in the BIOS-supplied DSDT; the battery is non-rechargeable and is discharging at an unknown rate. Sometimes acpi will even report that the battery has zero capacity.
The arch wiki does say mkinitcpio doesn't support the dsdt hook as of 2.6.30, but [1] didn't work either and mkinitcpio -H dsdt still told me to try this so I did.
[3]
The final solution I have tried has been to do [2] but to recompile the kernel with the legacy support for battery and ac adapter stuff disabled. I tried this because it was suggested in the kernel.log;
Sep 13 11:51:03 localhost kernel: [ 11.740059] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
Sep 13 11:51:03 localhost kernel: [ 11.753434] ACPI: AC Adapter [ADP1] (on-line)
The corresponding line now reads
ACPI: AC Adapter [ADP1] (on-line)
(The same goes for the battery BAT0)
but all this does is remove the battery/ and adp1/ folders from /proc/acpi/ and break acpitool functionality. The log still doesn't mention the dsdt hook, either.
[4]
The old way to do this was to use the acpi-dsdt-initrd-patch-* patch, but that hasn't been updated for modern kernels, presumably because of the new "functionality" from mkiniticpio. The current kernel .config doesn't include any options for ACPI initrd/initramfs support or reading a DSDT from initramfs, which is the functionality provided by this patch.
This covers all the methods I've been able to find on the internet and I'm at a loss for what to do. Am I doing something wrong in [1]? Under what conditions will the compiler fail/succeed with a CONFIG_ACPI_CUSTOM_DSDT_FILE?
When I recompile I fix the 'Zero' definition and a couple compiler errors and warnings. The errors come from section length definitions, which read as 0x00000000 rather than the appropriate max-min value so I fix those, and the warnings come from _T_* methods belonging to the compiler, so I refactor the code to remove the initial underscores. The last warning comes from an isolated And statement that's within brackets (compiler complains it doesn't do anything), but if I remove that the compiler fails hard.
Thanks to anyone who's read this far. Please let me know if you have any ideas how to get my system to use a customized DSDT.
Last edited by paraffin (2011-09-29 23:20:30)

Thanks for the offer, Radioactive man However, I'm actually compiling a customized kernel with the linux-ck and -sony patches, so your packages won't help. (The custom kernel works fine and I've tested this battery behavior on the the regular, -ck, and -sony kernels as well)
Anyway, so I tried another compile with
CONFIG_PREVENT_FIRMWARE_BUILD=n in addition to the options listed in [1] and that time it compiled.
Unfortunately it still didn't load the DSDT!
I did catch a quick little error message that turned up in kernel.log though;
/var/log/kernel.log:Sep 15 11:50:24 localhost kernel: [ 0.925780] acerhdf: unknown (unsupported) BIOS version Sony Corporation/VGN-FZ4000E/R2110J7, please report, aborting!
acerhdf is a fan controller module for the Aspire One, and perhaps I left that in the kernel config and it's preventing the custom DSDT from loading, even though the acerhdf module never gets loaded itself, nor is it in my rc.conf or anything else... If that was the cause of all this, I'm gonna be angry...
Anyway, this message does not appear with my latest kernel build because I took off the custom DSDT option, hoping to be able to use ACPI_CUSTOM_METHOD=y, which supposedly allows one to inject a custom AML method into a debug fs. It wouldn't have worked anyway, as it doesn't let you modify Device sections, but even with a dummy method insertion it didn't give my root modification privileges as it was supposed to...
Will try recompiling AGAIN with this CONFIG_ACERHDF=n (it's simply 'not set' in my current .config), while also enabling the custom kernel etc. If this doesn't work I have no idea what I'll do.
Anyway, thanks for your help and time:

IPad 4 with iOS 8 "read list" doesn't work

After updating to iOS 8, read list feature in Safari doesn't work animore!!!((( I can not read articles without the intertnet!
And also, Apple, come on, make iWork for free for rest of you costomers! It's ridicules to pay 30$ just only because that I bought the iPhone 4 and iPad 4 erlier...and even by highest price!

Hi
Sorry for being too nitpicky - BUT
You indicate iOS 8.1.2 on iPhone 4
Either you have a 4S or you have iOS 7.x
But with that said
Can you please check Settings -- General -- Accessibility - scroll down to Interaction -- Call Audio Routing and see if Automatic is checked?
Thanks

Where used list doesn't work for global data

Hi,
When i try to do where used list on a constant in an include, it doesn't give the results for classes.
The class contains the include in a method that uses the constant, and the where used list for that constant doesn't find the appearance of the constant in the class.
I tried to look for oss note that solves the problem but i couldn't find any.

I tried to update the navigation index but it still doesn't work. from my debuging i found out that it just doesn't look in classes, all classes. I mean even in the where used itself there is not an option for used in classes. I checked it and it's a generic problem of the where used list for global data.
Edited by: Cohen Lior on Apr 14, 2010 6:52 PM

10.2.0.424 search partial number in the call list doesn't work

The scenario is this
I remember I've been call from one number.
I only remember one part of the digits
Let's say 6532
I go to call list and go to use the search function
No results, but scrolling the call list and wasting a lot of time, I see that I was remembering correctly that number.
What is The point of having databases and a search function that doesn't work?
Thank you for replies and opinions
Cor

Toggling these items to OFF in the Hub settings prevents the messages from these sources from appearing in the main Hub view. This does not (currently) remove them from the Hub entirely. It's possible we may see that option in an upcoming OS release.

Clicking an element in a list doesn't work

Sorry about my rather vague subject - my problem is not so easy to sum up in a few words.
I am working on an application that
- Displays a list of items from a MySQL table
- Each item should be clickable, and on clicking should open an edit page with the clicked item pre-loaded
This must have been done millions of times before and should be simple. It doesn't work, presumably because I know too little. This is what I have done:
The clickable item list looks like this (without all the trimmings):
<h:dataTable id="users" value="#{userlist.userList()}" var="ul">
<h:commandLink action="#{ul.edituser}" value="#{ul.uid}"/>
This displays a list of the right sort of items, but the clickable item (the UID) doesn't do anything. Also, the resulting html looks the same no matter what I put into the action element - this is the inside of the a-tag:
href="#" onclick="mojarra.jsfcljs(document.getElementById('j_idt9'),{'j_idt9:users:1:j_idt15':'j_idt9:users:1:j_idt15'},'');return false"
I'm not entirely sure what that means; all I know is that it does not call the edituser() method.
But what is the right way, then? I haven't found any examples that highlight this particular situation although it must be used all the time, I expect.

#{userlist.userList()
#{ul.edituser}Spot the difference there. I do believe "ul" should be "userlist"; in other words it will link to an action method "edituser()" in a JSF managed bean which I assume will be named Userlist. Its really simple when you run into the problem of an action method not working: 99/100 times the action method EL declaration is wrong. Now it could be typo, but I've been known to forget the #{} part too...
I use the JBoss Tools Eclipse plugin myself; it has nice JSF additions that add EL validation and autocompletion to the editor. That way I know already from the code view when I've made a mistake in stead of "at runtime". A missing action method turns up as a warning in the jsf editor for example. That is of course only helpful when you're actually using Eclipse ;)

Firefox will not open ANY site. Wont work AT ALL. Nothing seems to be working.

Firefox will not open ANY site. It worked last night, but not today. I uninstalled it many times, didn't worked. It displays the screen that says "unable to connect" yet chrome and explorer both work. I have disconnected and reconnected a few times, restarted my laptop, neither of those worked either. I have also tried turning "safe mode" off after re installing firefox, but again, that did not work. I need help :(.
Although, before this, firefox was not letting me use voice recording sites or any site that let me watch television online. It would load the commercials, but not play the episode. It wouldn't even let me upload pictures to photobucket. However, it worked using chrome or explorer.

Looks like a bunch of people have this problem. Anyone got any ideas to fix this???

After updating iTunes 10.5 and iPhone 4 iOS 5 my phone doesn't work at all. It freezes while it is trying to do the Restore phone. That means I have not have a functional phone for two days now. Same thing happens with my iPad 2.

I updated Itunes to v 10.5. Mistake!!!! Then updated iOS 5 to my iPhone 4 now my iPhone doesn't work as the applications freezes when trying to restore the phone. Same thing happens with my iPad 2, so now I have two pieces of equipment that are completely non-functional. Can any please tell me what to do? How can I reinstall the previous versions of iTunes, or iOS which were working on my iPhone and on my iPad? I hate iTunes and this has been the last drop that messed up my equipment. Please help me. I do not have another phone to call APPLE. This ***** big time!! PLEASE HELP ME!!!

Connect to a computer to restore.

EA6350 Device List Doesn't Work Correctly

Device list doesn't show all devices on the network. Some are shown OFFLINE when in fact they are ONLINE.
Other devices that are connected don't even show up at all.
For instance, I have 15 devices on the network, some wired and some wireless, but only 10 devices show in the device
list. The other devices have connectivity but never show in the device list.
Called support and was told to update firmware and reset the router. Tried all of that but to no avail.
The device list is still incorrect.
When will Linksys engineers fix the firmware?

Make sure that your devices are set to obtain an automatic IP address. Check some of the devices which appeared on the list. It could be that some devices have multiple addresses listed below them, and if such is the case of your network, I suggest you inform Linksys Support about it.

Premiere elements 13 will not publish + share. eLive doesn't work.

Made my first video after downloading PE13 late last night. Unfortunately, I cannot publish and share. I click publish + share>computer>avhd. From there I've tried multiple preset options. Upon clicking save, the computer works for several minutes and a green checkmark appears with the words, "save complete!" Your video has been successfully saved. Thing is, when I go to the folder I saved it to and try to view the project, windows media player opens a half window and plays the audio from the movie I just saved.
The other issue is that I cannot upload directly to facebook, or YouTube. I have no options for logging in. When I click through to the screen and select "Authorize" I get a screen that says, "Thank you for authorizing Adobe PE13 to upload to your FB account. Select complete authorization to continue uploading the vid to your fb acct. When I hit "authorize" it comes back with "Error your authentication details could not be verified. Kindly try again. What Am I missing? I am logged into facebook. I even have a screen open in another window.
Could these two probs be related? eLive doesn't work either.
I'm running windows 8.1

GPPNeil
Premiere Elements 13 on Windows 8.1 (assumed 64 bit).
First..
1. Have you updated from 13 to the 13.1 Update using an opened project's Help Menu/Update. If not, please do so.
2. Do the problems exist if you disable the antivirus and firewall(s)?
3. Are you running the program as Administrator? Do you have the latest version of QuickTime installed on your computer?
4. Have you refreshed the Online Services using Premiere Elements Editor Edit Menu/Preferences/Web Sharing?
5. Have you updated the Adobe Application Manager?
http://www.adobe.com/support/downloads/detail.jsp?ftpID=4773
6.Is your video card/graphics card driver version up to date according to the web site of the manufacturer of the card?
7. Lots more we could go through such as deleting the Adobe Premiere Elements Prefs file and, if necessary, the whole
13.0 Folder in which it exists.
But, I think that you have enough things going on here to warrant an uninstall, free ccleaner run through (regular cleaner and registry cleaner parts) and then reinstall with the antivirus and firewall(s) disabled.
CCleaner - PC Optimization and Cleaning - Free Download
If the problems persist after all that then we will adjust to additional troubleshooting maneuvers.
Any questions or need clarification, please do not hesitate to ask.
Thank you.
ATR

"is not" doesn't work at all

I'm using iphoto 6.0.4 on OS/X 10.4.7 and have a library of ~8000 photos
mixed with film scans and digital captures. I'm trying to make separate
smart albums for film and digital...
smart albums by camera model and file name work great, but excluding
items doesn't work i.e.:
I created a smart album with "Camera model" (EOS 5D/EOS 10D) "is not"
and Filename "does not contain" (MG/IMG_/CRW)
my film scans do not contain any of that information
"match any" is active
this should show any non-digital photo in my smart album...
but iPhoto doesn't seem to work with the "is not" in the camera field
or with "does not contain" in the filename
any ideas?
Mark

doxx:
Welcome to the Apple Discussions. I'm able to use the "is not" search criteria in Smart Albums. Have you tried using just the Camera is not xxxx without the File Name criteria.
Do you Twango?

X-fi Extreme Gamers not in IRQ list, doesn't work at all.

Similar Messages

Maybe you are looking for