X240 touch screen and smart card seader problem

Hello
I installed Smart Card Reader (FRU 04X3984) to my X240 touch and after that the touch screen doesnt work. OS says that the "no pen or touch input available for this display". If I unplug the SCR cable from MB then touch function is going to work again. There are no conflict messages in system, they just doesnt work together!! 

Hello moban2010,
It sounds like you have two separate issues going on here. For the display and touchscreen response I suggest you use the following article to help isolate and resolve the situation.
iPhone, iPad, iPod touch: Troubleshooting touchscreen response
http://support.apple.com/kb/ts1827
For the alert you are getting that your sim card is not installed, there is another great article.
iPhone: Troubleshooting No SIM
http://support.apple.com/kb/TS4148
Thanks for reaching out,
-Joe

Similar Messages

  • Problems with Illustrator CC 2014 in Sony Vaio Fit 15A with N-Trig touch screen and digitizer pen.

    Hello to everybody!
    Some times ago Adobe has updated Illustrator to CC 2014 version and now it support touch pressure\pan\zoom in Windows 8 tablets. I have Sony Vaio Fit 15A with N-Trig touch screen and digitizer pen with pressure-sensitive support.
    I was extremely disappointed that the brush in new version does not work correctly. Watch the video please that I did specifically for the demonstration.
    I use Adobe Illustrator CS6 and Adobe Illustrator CC 2014 for comparison. In the old version the brush is works correctly. You must do a lot of clicks to start the brush in CC 2014 version (please see video). What causes of the problem? Please help me!

    Hello to everybody!
    Some times ago Adobe has updated Illustrator to CC 2014 version and now it support touch pressure\pan\zoom in Windows 8 tablets. I have Sony Vaio Fit 15A with N-Trig touch screen and digitizer pen with pressure-sensitive support.
    I was extremely disappointed that the brush in new version does not work correctly. Watch the video please that I did specifically for the demonstration.
    I use Adobe Illustrator CS6 and Adobe Illustrator CC 2014 for comparison. In the old version the brush is works correctly. You must do a lot of clicks to start the brush in CC 2014 version (please see video). What causes of the problem? Please help me!

  • Token and smart card reader are not detected on Mavericks if not plugged on a USB port during system boot

    Well, both token and smart card reader are not detected on OS X 10.9 if not plugged on a USB port during system boot. So, if I am already working within the system and need to use my certificates I have to plug the token or smart card reader on a USB port and restart Mavericks.
    Token is a GD Starsign and Smart Card Reader is a SCR3310 v2.
    Thoughts?

    SCS is a very good app, since I've read that Apple has discontinued support for PC/SC interfaces after the release of Mountain Lion.
    (My previous installation was a Mavericks upgrade from Lion)
    However, I don't know what and how to debug using Smart Card Services. Do you know any commands to use?
    Apparently, the SC reader reports no issues: the LED is blinking blue when no smart card is present and becomes fixed blue when a smart card is inserted – according to the manuals, this shows that there is correct communication between the OS and the CCID reader.
    I don't know what to do; I'm beginning to hypothesize it's a digital signer issue. In fact, my smart card only supports one application called File Protector (by Actalis) to officially sign digital documents. This application seems to have major difficulties in identifying the miniLector EVO.
    The generic and ambiguous internal error comes when I try to manually identify the peripheral.
    Athena CNS is one of the Italian smart cards and is automatically recognized and configured (so it's correct – no doubts about this), while "ACS ACR 38U-CCID 00 00" seems to be the real name of the miniLector.
    (I'm assuming this because System Information also returns that the real manufacturer is ACS... bit4id is a re-brander)
    However, when I click on it and then tap OK, it returns internal error.
    As first attempt, I would try to completely erase&clean File Protector files to try a reinstall. Then, if this still doesn't work, I'd debug using the terminal.
    So:
    - Do you know any applications to 100% clean files created by an installer?
    - Do you have in mind any solutions that I might have forgotten?
    Thanks in advance from an OS X fan!

  • When i open facebook and only text shows and all is to the left and when i open hotmail nothing shows on my screen and other webpages have problems also when click at a link all the text comes up also to the left in my screen whats wrong ???

    When i open facebook and only text shows and all is to the left and when i open hotmail nothing shows on my screen and other webpages have problems also when click at a link all the text comes up also to the left in my screen whats wrong ???

    Clear the cache and the cookies from sites that cause problems.
    * "Clear the Cache": Tools > Options > Advanced > Network > Offline Storage (Cache): "Clear Now"
    * "Remove the Cookies" from sites causing problems: Tools > Options > Privacy > Cookies: "Show Cookies"
    See also:
    * http://kb.mozillazine.org/Websites_look_wrong
    Start Firefox in <u>[[Safe Mode]]</u> to check if one of the extensions is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
    * Don't make any changes on the Safe mode start window.
    * https://support.mozilla.com/kb/Safe+Mode
    * [[Troubleshooting extensions and themes]]
    In Firefox 4 you can use one of these to start in <u>[[Safe mode]]</u>:
    * Help > Restart with Add-ons Disabled
    * Hold down the Shift key while double clicking the Firefox desktop shortcut (Windows)

  • JME support for touch screen and vibration

    Hi all, How are you?
    I need to develop a application for mobile phone, and it is going to use the mobile touch screen and vibration features.
    Does somebody know if there is an JME API, or JSR that provides access/control to Mobile's touch screen and vibration features?
    Does somebody know if it is feasible to do it using JME?
    I appreciate any help you can give,
    thanks in advance,
    Roger

    to use the mobile touch screen javax.microedition.lcdui.Canvas methods
    -- hasPointerEvents()
    -- hasPointerMotionEvents()
    -- pointerDragged(int x, int y)
    -- pointerPressed(int x, int y)
    -- pointerReleased(int x, int y)
    and vibration features?javax.microedition.lcdui.Display method
    -- vibrate(int duration)
    Also see proprietary vibration etc. APIs for Nokia / SonyEricsson:
    {color:#0000ff}http://www.wmlscript.it/j2me/nokia-UI-API-v11/com/nokia/mid/ui/DeviceControl.html
    http://developer.sonyericsson.com/entry.jspa?externalID=108&categoryID=12{color}
    db

  • Windows 8 upgrade problems (touch screen and audio)

    my　computer is HP touchsmart 600 1005xt and recently upgraded from windows 7 to windows 8 (64-bit)
    after up grading I noticed that the touch screen does not work and and the speakers also did not work

    HI,
    Here are a few tips that might help you to get your touch screen working:
    Activate Windows and install updates by pressing the Windows logo key + W. Type "Activate Windows" into the search field, and then click on the Activate Windows icon that appears in the upper left corner of the screen. In PC Settings, click on Activate Windows, wait for your computer to connect to Microsoft, and then follow the onscreen instructions. Restart the computer. Press the Windows logo key + X, and select Control Panel from the menu. In the upper right corner of Control Panel, select Large Icons from the View by drop down. Click Windows Update. Install touch and/or graphics driver updates. Restart the computer.
    Another thing to try: Go to the HP Support and Drivers site and click Drivers and Software.  In the search field, enter your product name or number, and then click Next. Select your operating system from the drop-down, and then click next. (If you don't know if your operating system is 32- or 64-bit, press the Windows logo + X key again and select System from the menu.) Follow the onscreen directions to install any appropriate drivers. Restart the computer.
    If the touch still doesn't work, try this: Press press the Windows logo + X key, and select Device Manager from the menu. In Device Manager, click the little triangle next to Display Adapters to expand the list. Right-click on the graphics card and select Disable. When asked if you want to disable the card, click yes. Restart the computer. You may have to tinker with your screen resolution.
    ~Lil.Liebe
    Clicking the white KUDOS THUMBS UP on the right is a way to say thanks!
    Click Accept as Solution on a reply that solves your issue to help others in search of answers.

  • Iphone 4 touch screen and other problems

    I have an iPhone 4 It recentley started acting up on me the touch screen stoped working and it stops charging other than that it all works.
    Charging- When I plug the charge on it has the "thunder" logo on it but doesnt charge. #probably logic board problem help me out?
    Touch screen- I know 100% its not the digitizers fault as I have changed it to another one and it still the same thing #probably logic board problem
    I tryed hard booting and itunes doesnt reconise
    I t was water damaged but fixed, when the water damage was fixed the touch screen still didn't work.

    Try these guys for parts, i got mine fixed here
    iphone 4s parts
    or if you dont want to do it yourself then get them fix it
    iphone 4s screen replacement service

  • Remote desktop and smart card

    Hi.
    I need to use a smart card while working with remote desktop.
    My office pc runs win XP and have a smart card connected. I can not use that card when working remotly, its not found. Like its disconnected.
    I also have a smart card connected to my Mac at home. The smart card works fine when the VPN connection ask for my code.
    The problem is that it does not get forwarded. I have tried to use MS Remote Desktop for mac and CoRD.
    But none of them supports the smart card.
    It works fine with parallels/win7 on my mac, I can then use my smart card.
    How ever I would like to not use the win/ on my mac.
    Do anybody have a soulution to this? Are there any Remote desktop applications that support forwarding of smart card for Mac OS?
    Thanx for any tips

    You can install rdesktop with Smart Card support.
    It is fairly easy if you use something like MacPorts, Fink, or Homebrew.
    I know MacPorts has a port for it that I used in the past.

  • While reading mail, touched screen and content turned into "Chinese"--on server too!

    I cannot now read this email! I've also had problems where I accidentally touch the screen and the email is deleted form the iphone, but I am able to get it off the server. This is a huge problem--as essential email from someone whose address I don't have. Thanks.

    OK sorry, I figured out what happened. I somehow moved the message to deleted iems on the server. I don't know how I did that but at least I was able to retreive it. Now if you tell me how to delete this message, I will.

  • Lenovo Flex 14 issues with touch screen and hard drive

    Dear Lenovo,
    I've just bought this laptop about 3 months ago. First the touch screen giving issue, so went to the service center and they repaired by saying there are problem with the motherboard. Then after a week, problem with windows booting and the touch screen issue still hasn't resolved. When i turn on my laptop it prompts cannot detect hard drive. I've been going to the service center multiple number of times but only worsening my problem.
    I am so frustrated now and don't know what to do. Can Lenovo replace my laptop ?
    Does anyone here have similar issue and have a solution because i just loose hope with the service center ?
    Please kindly reply me as soon as possible.
    Thank you.

    thana88,
    Sorry to hear that you have had multiple service events, and yet problems persist.
    Please send me a private message with your contact information - name, phone number and the type / serial number of your flex 14.  If you have any of the service case numbers, please include these as well..
    We can work to escalate this
    Mark
    ThinkPads: S30, T43, X60t, X1, W700ds, IdeaPad Y710, IdeaCentre: A300, IdeaPad K1
    Mark Hopkins
    Program Manager, Lenovo Social Media (Services)
    twitter @lenovoforums
    English Community   Deutsche Community   Comunidad en Español   Русскоязычное Сообщество

  • Touch screen and pen/stylus stop working - Helix

    Note taking with my new Helix is unbelievably frustrating! It's Windows 8 Pro -- fully updated (Windows and Lenovo drivers and apps). I am using Microsoft OneNote 2013. The problem is regular locking up or freezing of one or the other of the touch screen or the pen / stylus. Sometimes the pen still works, but fingers on the touch screen have no effect. Other times the the touch screen works, but not the pen. I'm not 100% certain that it's limited just to OneNote, but that's where it's guaranteed to happen. I can "fix" the problem most of the time by putting the Helix into sleep mode and then waking. Other times I have to shut down and restart. During a two hour session this will happen a dozen times at least. This makes it nearly unusable. Rob

    teachmoorenglis wrote:
    Just got this Helix for a test-drive and I'm already having problems with the stylus/touch.  I can't quite tell why, but after working with computer as a tablet for a while, the touch turns off.  Then, if I pull the stylus out of the pocket 1/2 inch or so, the touch turns back on, then about 30 seconds later it goes off.  Then, if you pop the stylus back into the slot all the way, the touch screen is fine again for several minutes.  Over and over, i'm finding the interplay between touch and stylus to be a bit quirky.  Maybe it's the machine i got or maybe it's a general problem. I have had the exact problem with the touchscreen not working without fiddling with the pen in the socket (put it in, take it out, touch it etc). Do you have the task bar on the left hand side? I've had diffiuclties with the digitizer, can't use the bottom or right of the screen for example.  I'm wondering if still detects that the pen is near it. If I see the problem again I'll be trying the task bar on the right side.  If that doesn't help I have to assume a broken switch in the pen holder / bad digitzer.   Neither of which is good on a 2500 chf machine, especially one with what seems to be a warped tablet or base (still have to measure that).

  • Remote desktop and smart cards

    I frequently work from home using my mac to access my windows based desktop at the office. I use the microsoft remote desktop v. 1.0.3. for MAC. Now that my agency is moving to smart card identification requirements for access I need to be able to use the smart card at home to sign onto the office desktop.
    The RDC for MAC does not have an option for smart card readers (as opposed to the RDC for windows version). Is there alternative software that would be simple to install on my MAC (I am not an IT sophisticate) that will give me smart card access?

    Microsoft Remote Desktop Connection (RDC) for Mac and Apple Remote Desktop (ARD) are two completely different tools with marginally similar capabilities. Unfortunately, as you've already discovered, neither offers Smart Card capabilities to allow you to authenticate to your Windows computer at work.
    If your Mac is an Intel Mac then you could probably run Windows using Parallels or Boot Camp on your home computer and use the Windows RDC client to make your connection. I don't suggest trying to use VirtualPC if you have a PowerPC Mac simply because your Smart Card reader will most likely be USB and VirtualPC has a bad track record with USB devices.
    Hope this helps!
    bill
      Mac OS X (10.4.10)   1 GHz Powerbook G4

  • MS Remote Desktop and smart card reader

    I have installed MS Remote Desktop Conn. on my iMac and connected a smart card reader via the USB. Although my reader energizes when the computer is on, the computer doesn't seem to recognize the reader. When I insert a CAC card into the reader and try to log in remotely, I continue to get a "username/password" box instead of the CAC PIN number. Do I need to install some kind of smart card driver or does Apple already have it? I'm at a loss as to how to fix this.

    I was able to get rdesktop 1.6.0 to install on my Mac and I was able to get CAC log-in to work.
    However, the installation is a little tricky. I downloaded rdesktop 1.6.0 from this link:
    <<http://www.rdesktop.org>>
    My instructions for installation:
    1. Make sure Xcode Tools is installed on your computer. It should be on your OS X install disk.
    2. Find out where your X11 libraries are located:
    -From the Finder menu, selct "Go" >> "Go to Folder..."
    -Type (without the quotes) "/usr/X11", and click "Go"
    You should see a bunch of folders. Make sure the "include" and "lib" folders are there. Otherwise you need to find out where the X11 "include" and "lib" folders are located on your computer.
    3. Download rdesktop and place the (unarchived) rdesktop-1.6.0 folder on your Desktop
    4. Open the X11 application (should be in your Utilities folder)
    5. In the X11 window type the following (without the quotes):
    "cd Desktop/rdesktop-1.6.0 && ./configure --enable-smartcard -x-includes=/usr/X11/include -x-libraries=/usr/X11/lib && make && sudo make install"
    4. Hit enter. When prompted, enter your administrator password and hit enter.
    rdesktop should now be installed in the following folder:
    /usr/local/bin
    So, to launch rdesktop with smartcard log in enabled, open the X11 application (or Terminal application) and type the following (without the quotes, and replace your.server.address with the server address):
    "cd /usr/local/bin && ./rdesktop -r scard your.server.address"
    Hit enter and it should launch a new X11 window that will try to access the remote server where you should be prompted for your PIN.
    To explore more options with rdesktop, open X11 and type the following (without quotes):
    "cd /usr/local/bin && ./rdesktop"
    Hit enter and you should get a list of options available to rdesktop.

  • ISE 802.1x EAP-TLS machine and smart card authentication

    I suspect I know the answer to this, but thought that I would throw it out there anway...
    With Cisco ISE 1.2 is it possible to enable 802.1x machine AND user smart card  authentication simultaneously for wired/wireless clients (specifically  Windows 7/8, but Linux or OSX would also be good).  I can find plenty of  information regarding 802.1x machine authentication (EAP-TLS) and user  password authentication (PEAP), but none about dual EAP-TLS  authentication using certificates for machines and users at the same time.  I think I can figure out how to configure such a policy in ISE, but options seem to be lacking on the client end.  For example, the Windows 7 supplicant seems only able to present either a machine or user smart card certificate, not one then the other.  Plus, I am not sure how the client would know which certificate to present, or if the type can be specified from the authenticator.

    Hope this video link will help you
    http://www.labminutes.com/sec0045_ise_1_1_wired_dot1x_machine_auth_eap-tls

  • Pkcs#11 and smart card reader

    Hi everybody,
    In my applet code
    i'm trying to implement "attached signature" reading keystore from a smartcard.
    I'm using SunPKCS11 provider and infocamere smart card, so i load SunPKCS11.dll for PKCS#11 standard.
    my code is:
    String pkcs11ConfigFile = "c:\\smartcards\\config\\SI_PKCS11.cfg";
    Provider pkcs11Provider = new sun.security.pkcs11.SunPKCS11(pkcs11ConfigFile);
    Security.addProvider(pkcs11Provider);
    where SI_PKCS11.cfg file contains 2 lines like follow:
    name = test
    library = C:\WINNT\system32\SI_PKCS11.dll
    when I try to sign without smart card in the device reader i catch "PKCS#11 not found" exception, while when I try with smart card inside the device the applet stop on loading the provider and it doesn't continue without any errors in java console. Can anyone help me?
    thanks a lot for every answer
    best reagards

    I should add that I am using Windows 7 and my CSS version is 8.3, I can also verify my smart card works for other applications, only thinkvantage CSS 8.3 does not work.

Maybe you are looking for