Yosemite and Time capsule not working?

I just started using Yosemite on my mac book pro laptop and my mac desktop. Time machine has been fine on my desktop with my external drive which is plugged into the computer. I had no problem with new backups. But, I can't get time machine to work with my laptop and time capsule. I have another external cloud drive as well, and it will not work with that one now either. First, I can no longer just open up my backups from the folders in the finder like I used to be able to. instead all I see is a disk image with my back up and when I click on it I can not open it and get an error message (see below). Also, it will not back up at all, it give me the other error message in this picture. What is going on here? I am so frustrated. I may just have to go to the genius bar but this is so frustrating.
I also can't even access my back ups now from before even if I go in through the finder window and select the hard drive the back up do to go very far back. Only a few days. I am worried that somehow all of my backups are gone but am hoping that is not the case. It all worked fine before I installed Yosemite. I would appreciate any help or guidance.
For the first image, if I try to back up to time capsule I get the exact same message except it says could not back up to the name of my time capsule drive.

A third-party NAS is unsuitable for use with Time Machine, especially if it's your only backup. I know this isn't what you want to hear. I know that Time Machine accepts the NAS as a backup destination. I know that the manufacturer says the device will work with Time Machine, and I also know that it usually seems to work. Except when you try to restore, and find that you can't.
Apple has published a specification for network devices that work with Time Machine. None of the third-party NAS vendors, as far as I know, meets that specification. They all use the incomplete, obsolete Netatalk implementation of Apple Filing Protocol.
If you want network backup, use as the destination either an Apple Time Capsule or an external storage device connected to another Mac or to an 802.11ac AirPort base station. Only the 802.11ac base stations support Time Machine, not any older model.
Otherwise, don't use Time Machine at all. There are other ways to back up, though none of them is anywhere near as efficient or as well integrated with OS X. I don't have a specific recommendation.
If you're determined to keep using the NAS with Time Machine, your only recourse for any problems that result is to the manufacturer (which will blame Apple, or you, or anyone but itself.)

Similar Messages

Time Machine and Time Capsule not working well.

Greetings,
I am having strange issues with Time Machine and the Time Capsule. I am using a MacBook Pro and have the 1TB Time Capsule. I am also using the Time Capsule as the wireless base station for my network.
The issue is, Time Machine has only once created a full back-up. Since then, it could not either connect to the disk or mount the image. I have tried several things like renaming my computer and renaming the Time Capsule. I have also tried copying via LAN and wireless. I even went as far as erasing the disk.
Now that the disk is erased, Time Machine cannot create an imgage on the drive. This is my latest issue.
Is this kind of trouble wide spread or very rare? Any way to fix it?
As a work-around, I am using Smart Backup instead of Time Machine to do my back-ups.

Standard Lion and ML issue..
Just reboot the TC.. sometimes with ML you may need to reboot the whole network.
In Lion you can use 5.6utilty and disconnect all users.. but apple has not made 5.6 utility available for ML or not yet. Perhaps they don't know about the bug. or if you put your head deep enough in the sand you can pretend there is no such problem.. it does expose some other parts!!
Pondini has info on a work around to load 5.6 utility into ML.
Read C12 and C17
http://pondini.org/TM/Troubleshooting.html

Time Machine and Time Capsule not working

Hello,
I got a Time Capsule yesterday and set it up and it was working fine. I saw it backing up my iMac and my internet connection was fine with my MB and iMac. But today the backup to TM failed. I tried going to Airport utility but it does not detect the TC, nor does TC...Help please?
Thanks,
David

David,
*Cycle Airport Preferences*
Open Network Preferences.
Click “Turn Airport Off”, wait 10 seconds.
Now click “Turn Airport On”. Close Prefs.
Does it now show up in Airport Utilities?.
If not go to the “File” menu and select “Rescan”.
Does it appears now?.
If not, unplug the TC, wait 10 seconds, and plug it back in.
Let us know if this helps.

The date and time is not working after setting it to current date and goes back to may,26 2011

the date and time is not working after setting it to current date and goes back to may,26 2011; 2 PM . I bought my ipod tocuh 4th gen on july 18th

On the iPod, make sure your Calendar is set to Gregorian (Settings > General > International > Calendar). Also make sure your date and time on your computer is correct as well as the Time Zones on both.

Excluding items from back up and Time Capsule not recognising ext HD

I'm relatively new to the world of Time Machine and Time Capsule. I have a 250Gb iMac, but because my iTunes library was becoming so large I purchased a Iomega 500Gb ext HD and transferred it over to this where it is currently occupying about 350Gb of space. I still have about 220Gb duplicated on my iMac at the moment as a kind of back up. I then discovered Time Machine and because there was only about 100Gb of space left on the ext HD to do back ups on I excluded my music and iTunes library from this. This has been going along fine for the past month.
I purchase a 2 TB Time Capsule (TC) yesterday. I reconfigured Time Machine to use the TC as the back up and I removed the excluded music/iTunes library so that everything would be backed up. As soon as I asked TM to back up it started excluding millions of items which I am assuming is related to the ext HD since when I turned this off it started to back up my iMac computer content correctly. However I want to be able to back up the stuff I have on my external HD so that I can eventually delete all the duplicated stuff off the iMac. I read a similar post on here about this and have tried deleting all the old TM backups but it is still not recognising the ext HD. I currently have it connected via an ethernet cable just to speed up the initial back up. Any help or explanations would be greatly appreciated.

Dear Bob
Thanks for trying to help me with this
Bob Timmons wrote:
I read a similar post on here about this and have tried deleting all the old TM backups but it is still not recognising the ext HD.
Sorry, I am confused here. You mention that you have a new 2 TB Time Capsule, yet talk about trying to delete old TM backups. What old TM backups, if you have a new 2 TB Capsule? Can you clarify, please?
but it is still not recognising the ext HD
A bit more clarification here, please. When you refer to "it", do you mean Time Machine?
Time Machine will not backup an external drive connected to a Mac unless the drive has been formatted in Mac OS Extended (Journaled). Did you format the drive this way when you first got it?
If the drive was formatted as FAT32 when it was new, it would work OK if you attached it directly to your Mac. But if you want Time Machine to backup the Iomega drive attached to your computer, the drive must be formatted correctly to work with Time Machine.
If you have the drive attached to the Mac and you open Time Machine Preferences and click Options, can you "see" the Iomega drive and not select it, or can you not "see" it at all?
If you can "see" it, but it is grayed out so you cannot select it, the drive is not formatted correctly as mentioned above. If that is the case, you will somehow need to copy all of the data on the drive to another location, format the Iomega drive to use Mac OS Extended (Journaled), and then transfer the data back to the Iomega drive. Then, Time Machine will backup both your Mac and the external drive attached to your Mac.

AirPort Time Capsule not working.

Tried hard and factory reset but stays amber. It turns green for a second when it gets plugged in but turns amber again. Also, unplugged internet and time capsule to try and reset it but nothing changed. It is not being recognized in my airport utility as a base station but it shows up as my time capsule in the airport utility with a yellow triangle and ! in it. When I open my time machine preferences it's not there. Any other suggestions?

Solid amber means it is dead.. the hard disk is most likely cause but it can also be the power supply or combo of both..
The Gen2 TC is now well past useby date.. buy another one..
You can repair it but the cost is higher than the result is worth.. Gen2 used a WD black drive and they seem to crash out about now.. so it likely has a dead disk .. you can open it and remove the disk.. the TC will then work as an airport extreme Gen3.. and even the disk might test OK.. but your internal power supply no longer can power it.. if however when you start up you hear the disk noises of death.. well it is more likely ended its life.. !!

The setting date and time is not working

Bought an apple TV, installed it as per instruction, connected to my internet but the seting date and time is not occuring and the activation cannot occur either. Spent 1 hr on the phone with Apple support staff - they told me it may be a router blockage and to contact my internet provider. contacted internet provider , they tell me everything is working from their end so must be the apple TV device. I was told this was easy techonology and that I would not have issues - I have spent 3 hrs on this and truly frustrated as its not working . any suggestions would help!

That would be a network issue as you were initially advised. When the date and time can not be set it means it is having trouble connecting to the network.
Make sure router is up to date, reboot router and ATV. Make sure location is set correctly via ATV and also DNS (settings - general - network - configure DNS - automatic)
Make sure your router allows access over port 123.
Failing that try a restore on the unit

AirPort Extreme and AirPort Time Capsule not working

So heres the situation: I have 1 airport extreme in the house and another in the office separate from the house. The cable modem connects to the aiport express in the house through ehternet. An ethernet chord goes from the Aiport Extreme from in the house to the office in the back yard.
Decided to update my airport extremes with the new tall ones. Bought the normal one for the house and got the Airport Extreme Time capsule for the office.
But nothing works. Reseted the device, unpluged the modems power and cables and still nothing ... just blinks yellow
I feel like the NEW Aiport Extremes are not talking to the modem ... theres some diconnection between the airports and the modem.
So there both sitting on my desk until i can figure out what the problem is.
The modem is provided from Time Warner, Los Angeles area. Its maybe 1.5 to 2 years old
Any thoughts or suggestions would be much apprecaited, thanks!

The cable modem remembers your old AirPort Extreme and it will not associate with the new AirPort Extreme until it....the modem....is completely reset to the point where it has forgotten your old AirPort Extreme.
Power off the modem completely by pulling the power plug from the back of the device
Leave it off at least 30 minutes. longer will not hurt at all.
Power up the new AirPort Extreme for a few minutes
Hold in the reset button on the Extreme firmly for 10 seconds and release
Allow a full minute for the AirPort Extreme to restart
Now power off the AirPort Extreme
After the modem power down period is done, connect an Ethernet cable from the modem to the WAN "O" Port on the AirPort Extreme
Power up the modem and let it run for 10 minutes by itself
Power up the AirPort Extreme and let it run a few minutes
Now try to set up the AirPort Extreme using AirPort Utility
Post back on your progress and we will get the new Time Capsule set up next.

Time Capsule Not Working With Time Machine

I'm trying to backup to my Time Capsule, which I haven't used in over two years. It had been displaced because of a change in internet service providers. The new provider came in with a Linksys router, setup a sub-network, and left the Time Capsule/Airport out of the mix.
So I want to return to using my Time Capsule and have since pulled out the Linksys router, and got the Airport functionality working with the existing, primary network. In other words, the Time Capsule/Airport is working to extend the range of the network.
Problem is this: I cannot backup to the Time Capsule. Even if I'm connecting to the Time Capsule via ethernet, I cannot get it past the 'preparing' phase when running Time Machine. It stays at the phase for what seems to me an inordinate amount of time (30-45 minutes). If I go into System Preferences, the Time Capsule disk doesn't make itself available when using it with Time Machine. If I choose to go into the Star Wars display of Time Machine, I can sort of see the various backups, but I can't roll back to them, and the backup indicator on the right looks sort of ghosted, like it's there but it's not there.
How do I know if the disk within the Time Capsule is failing? Could that be what's going on? How would I test it? I get a green light on the front of the TC, but not everything is hunky dory since I'm not able to backup.
Is part of my problem that I'm using a not up-to-date version of Airport Utility? –I'm using 5.4.2

Oh and here it is, on this page, Section D, #1:
"Section D. OTHER PROBLEMS RUNNING BACKUPS
D1. Stuck in "Calculating changes" or "Preparing""
and then the Apple supporting doc, as well:
http://support.apple.com/kb/TS1516
Fabulous. Thank you.

HT1175 3TB time capsule not working with new iMac

I have a 3TB time capsule that's c. 2 years old. It worked perfectly with my old iMac. I bought a new 27" one when it came out this year and since the time capsule will not work.
I had to clear all the data as a starter. Now it gets a little into the backup taking c. 1 day then resets. It's connected via ethernet cable and has been told to join an existing network.
Currently it says it's backing up 922,498 items, after 2 hours (this is the third attempt, it resets then has no record of the old backup) it says 10kb of 789.44 GB - About 4,664,440 days remaining!!
To clarify I'm trying to use Time Machine with the Time Capsule.
Please help!!

You have made a mistake in the setup.
You do not "Join an existing networking" and use ethernet.. they are mutually exclusive.
What you are doing is backing up over double hop wireless which is slowing to a crawl.
You need to put the TC into bridge mode.. and plug it into the main router by ethernet. Then use wiretess to the TC if you are too far away or ethernet if you are close by..
As soon as you put the TC into join a wireless network it deactivates the ethernet.

New Air Port Time Capsule Not Working With Old Airport Express

I have been running a home network comprised of a Air Port Time Capsule (A1254) and 5 ea Air Port Express (A1264) for several years with no problem.
The Air Port Time Capsule (A1254) died and I replaced it with an Air Port Time (A1470). Now none of the Air Port Express (A1264) work, all flashing yellow. All other network functions seem to work okay, Time Capsule Backup, Apple TV, Internet …
I am using AirPortUtility 6.3.1 for setup but do not see any way to setup the Air Port Express.

Reset the Express to factory and start over.. they should work.. are you using all 5 in extend wireless mode?
When you reset the Express click on the wifi icon in the top menu area.. and the newly reset AEx will appear in the list.. click it and Airport utility will open and attempt to automagically connect it to the TC.

Time capsule not working properly after moving to a new house

Hello,
I have a macbook pro and a refurbished time capsule 2tb. I purchased both in 2013 and the time capsule at that time was used as both a wireless router for our house and my back up.I recently moved and didn't have access to the time capsule for over a month. Once I settled into the new house I plugged the power cable and internet connection into the time capsule and assumed that automatically it would keep working. It appears that it is backing up my system as I can pull up the application and see appropriate in-time documents however it consistently has a slow orange light blinking. I am not currently using it as a router as we have xfinity and have a different router for the house and when I try to use the time machine instead it cannot connect.
My internet connection is fine and I would like to leave it as is. It also appears the back up function is working for my mac. The question is, does the orange blinking light matter and or is it indicating that I am improperly using the machine? It it because the ethernet cable is attached and can the time capsule work without this?
I have tried resetting the capsule with the 10seconds hold on the reset button etc as seen on other posts but the orange light remains.
Thoughts?
Thank you for your time and assistance,
ahahn063

The question is, does the orange blinking light matter and or is it indicating that I am improperly using the machine?
The amber light is like the "Check Engine" light in your car. It blinks for a reason......the Time Capsule has a message for you.
That message might be that there is a firmware update available for the Time Capsule that needs to be installed....or....that AirPort Utility has detected that the Time Capsule is not configured correctly to work with the Xfinity router that you are now using.
To see the message.....open Finder > Applications > Utilities > AirPort Utility
Click on the amber dot
Then look for a Status setting, and click on the small amber dot there
A message will appear to tell you why the Time Capsule is whining, along with a suggested action to fix the issue.
If you are still having difficult, we for you to post back with the exact message that you see.

Time Capsule not working after a restore

I recently had to restore from my TM/TC backup after a standard software update made it so I could no longer log into my account. Now, my TC is not working properly. I can still access all of my past updates on mu TC, but it is not working for making new backups. Instead of backing up the new files, TM wants to do a whole new backup from scratch (all 140 gigs). Worse still, it is unbelievably slow (as in it took over 3 hours just to do 1 gig last night on my wireless.)
If I can still access all my old files on the TC and I restored my Mac using the TC files, why is it that TM wants to start an entire new backup now instead of continuing to update the original one? And, why is the updating crawling along at such a terribly slow speed. Any thoughts/proposed solutions to this very much appreciated.

I found this article which describes a fix:
http://www.macosxhints.com/article.php?story=20080128003716101
I'm testing it on my Time Capsule now, I'll let you know how it goes.

Time Capsule not working!

I have an iMac about 3 years old. I have a time capsule about the same. I have Mountain Lion. The Time Capsule keeps wanting to back up 33.44 GB of something. Is says the oldest backup was in April 26, 2012. What do I need to do to get it working?
Thank you
Carl

Mountain Lion seems to generate ghost disks.. I am not sure why but they might or might not delete.
I guess my method would be to start over.. use a better name..
Short no spaces pure alphanumeric. Not "Carl's Time Capsule"
You can put CarlTC
After you make the change reboot everything.. modem router TC client computers. To make sure you have fresh new view of the network.. then delete all the old names.
Redirect TM to the new name.. but the change will not affect the backup which is stored and TM should be able to pick it up and continue.

Time Capsule not working after last software update

I bought my time capsule 3 weeks ago. Set up and worked like a charm (I use airport express for my wireless network). After I downloaded the latest software updates a week or so ago, I got a message that my computer could no longer recognize my time capsule. Since then the time capsule light only flashes amber and wont appear in airport utility.
Any ideas?
Thanks

I was having problems with the 7.3.1 firmware as well. For me, in manifest as though the internal disk had went bad--a blinky amber light and a "Disk needs repair" error. Rolling back the firmware solved it for me.
To do this:
--Open AirPort Utility.
--Click on your TC.
--Click on the "Manual Setup" button.
--When the configuration summary pops up, click on the word "Version".
--From the "Upload" drop-down list that is on the new pane that pops up, select "7.3", and click "Ok".
--Once it reboots, it'll be at 7.3.
Hope this helps. I'll be waiting a few weeks after 7.3.2 comes out to upgrade. I'm not real impressed with 7.3.1. As far as I can tell, it broke more than it fixed.

Yosemite and Time capsule not working?

Similar Messages

Maybe you are looking for