Z50-75, wont boot after bios update

Hi to all!
I just baught Z50-75 with AMD FX7500, 8GB Ram and FreeDOS. I installed Windows 8.1 Pro, and they pulled some drivers during the installation, and I went to Lenovo sight and downloaded all the rest (graphics, camera, etc.), after each installation the computer restarted normally and all was O.K. The last drivers that I saw on the site were BIOS drivers, and I downloaded those to and it started the installation after which it said:"The system will now restart for changes to make effect", and it did, but, it would not boot up after that, all it did was show me this on the screen:
And I tried both of the options (the second one with the Windows CD inside), but it just stays where it is, no effect.
I can enter the bios and change the settings, but none of them seem to work because this is the maximum where it will go, the only difference is when I change from AHCI to Compatible mode, it restarts and than I have a blank screen, I have to use the One button Recovery to get back to this one from the picture above...
I would appriciate any kond of help, please give me some advice.
Solved!
Go to Solution.

Someone else posted about a similar problem. I will give you the link to their post and you can decide if it is something you want to try.
http://forums.lenovo.com/t5/Windows-8-and-8-1/black-screen-after-2-reboot/td-p/1738899
Hoov
Microsoft MVP - Consumer Security
SpywareHammer.com

Similar Messages

  • Laptop wont boot after BIOS update

    Hello
    i have a compaq CQ61-303SV laptop
    i tried to update the BIOS and i download the file form the hp driver and support website
    after i update the BIOS the laptop wont to boot and stop on a black screen
    what to do please ...

    Power down the notebook, disconnect AC adapter and remove the Battery, hold the power button down for a full 30 seconds, connect AC only, hit the power button and see if windows will load.

  • T540p wont boot after bios update

    I updated my T540p a few days ago using Lenovo Solution centre, hiwever, it cant boot after update. The power button is on and fan spins, but the screen is black. I tried: remove battery and all external device and press power button for 30 seconds, out back the battery, still screen wont show anything; tried usb recovery stick, didn't work; tried Recovery discs from Lenovo, still failed.
    Please help. Thanks in advance.

    Ouch.  And just out of luck. 
    Chances are, the board is bricked. 

  • Pavilion g6t wont boot after bios update now just black screen please help!

     I downloaded an update for the bios for my pavilion g6t-1d00 laptop running windows 7 64 bit. It started acting kind of funny but I didnt think anything of it til I tried to boot it up the next day and all I got was a black screen and a orange led light on the f12 button for the internet and the caps lock button after blinking afew times started the dredded two times every couple of seconds. I tried the windows key+B key power key, no luck. I cant access anything because I have no monitor and I'm at my wits end. I refuse to wipe my hard drive and start over even if I could! I cant access hp tools or manager or anything, please someone has to have a solution!

    @Fuschia4me,
    1.       You will have to use another computer
    2.       Access the HP.com site with the BIOS updates available here is the link
    3.       You want to select the F.36 BIOS version
    4.       When you click on the update then click download and it will ask you to save or run, you want to save to a flash drive
    5.        Once done insert the flash drive into your laptop
    6.       Turn the computer on and press the windows and B key like before
    If the process doesn’t work the first time I would try at least 2 more times.
    Please respond back at your earliest convenience.
    Thanks
    Clicking the White Kudos star on the left is a way to say Thanks!
    Clicking the 'Accept as Solution' button is a way to let others know which steps helped solve the problem!

  • Pavilion m9500y wont boot after bios update

    Hello Everyone, 
    I have a m9500y desktop that I recently did a bios update on. The update seemed to go through just fine but then when it rebooted it ended up beeping a few times and showed only a black screen. I removed the power cord and cmos battery and tried to power on after putting them back. It came back to the boot screen and hitting f10, it says "Entering Setup" and a flashing cursor, but doesn't get passed that. Is there a way to get into some recovery mode and reflash the bios again?
    Thank you in advance for any help. 

    Hi,
    There is one HP BIOS update available for your PC when using Win Vista 64 bit.
    Is this the update that has failed? Did you attempt this BIOS update running a different version of Windows?
    It may be possible to mod the BIOS update per above and flash again. Another option is to have HP reflash your PC's BIOS. The cost to have HP fix may not be worth it given your PC's introduction date in 2008.
    This site may provide some help. Check out BIOS Recovery. Current HP PC's use AMI BIOS. Your PC may have an Award BIOS.
    Or you could contact a local PC tech for assistance. The tech may be able to reflash the BIOS at a lower cost.
    There is no easy fix for this problem.
    Jaco
    ****I am not an HP employee****
    Please give a" Kudos, Thumbs Up" if advice received is relevant or" Accept as Solution" to assist other forum users having a similar problem.
    Errare humanum est.

  • K9N Diamond - Wont boot after BIOS update

    Just attempted to update the BIOS on my PC and it now wont boot.  Used LiveUpdate with the Windows flash option (don't have FD drive).  The lights on the D-Bracket 2  get as far as LED 2 Green, 1,3,4 Red.  I have already tried to Clear CMOS with no joy.
    Any suggestions on how to proceed much appreciated  - and yes, I already know, I've probably done something stupid
    Thanks
    Grant.

    Quote from: BOSSKILLER on 25-March-07, 19:22:15
    power down PC, remove power cord from the PSU, push several times power button to drain capacitors, then Clear CMOS and leave only one memory stick into DIMM slot close to CPU socket. pull back power cord and try to boot.
    in a future do not update the BIOS for no reason....(only becouse its new, only becouse new BIOS maybe got a new logo and e.g...)
    Looks like I'm back in business now.  I found similar instructions at this location  http://www.bosamar.com/K9N/trouble.html and followed the First Procedure.
    Booted ok with one mem stick, in bios fail safe mode.  I counted 7 short beeps while booting then one long beep.  Not sure if this is ok.  Read about bios beeps here https://forum-en.msi.com/index.php?topic=82221.0 and the final long beep seems to indicate a pass???.  Anyway, Vista appeared to come up ok and I checked everything in the hardware device manager and all looked fine.
    Proceed to reboot with all mem sticks back in place, again same beeps but Vista coming up ok.
    Next I switched bios to optimized defaults, but now 6 short beeps - no long beep.  Windows looks ok.  6 beeps appear to indicate a keyboard problem, but kbd seems to work fine???
    System looks ok now, but not sure if i should look into those beeps a bit more?  BIOS now at 1.3, should I leave as is or revert to an earlier revision?
    One thing I know that I am going to do is to install the FD drive from my old PC 
    Thanks for all the help.
    BTW, the reason I did the BIOS flash was as a last resort to get my sound to work.  Tried the various creative driver as suggest elsewhere on this forum but without success (as of yet there is no official vista compatible audio driver for my mb from MSI).  The JAUD1 connector looks to be connected as specified in manual (but no audio from either the front nor real panel audio connectors).

  • Xp wont boot after bios update with dualcore amd 4200+ (k8n-neo2 platinum)

    after flashing the bios (xp already installed on a sata stripe array)
    xp wouldn't boot anymore ... ik had to flash the bios to be able to
    use my amd x2 4200+ ...
    so I tried to instal xp freshly on the sata raid ... hangs when it restarts to instal devices ... nothing would help diffrent drivers , basic bios settings , all pci cards removed and switched of everything i could in the bios to get a really basic setup
    to instal ... no help whatsoever ...
    now if i try to instal on a normal ide everything works like a breeze ... dual core , raid , everything ...
    personaly I suspect either the windows instal stuff to be the problem with dualcore
    but even more the nforce drivers since they have not been updated since june 2004 ...
    can someone help me out please ???

    Quote from: Budwise on 22-September-05, 13:08:34
    try 1.B
    If you check in his sig he is using 1b.
    Quote from: Wonkanoby on 21-September-05, 15:36:21
    there are newer nforce raid/ide drivers thasn that
    http://www.nforcershq.com/forum/nforce4-driver-812-vt62037.html
    His board is a NForce3. Here is the actually link for the drivers. http://www.nvidia.com/object/nforce_udp_winxp_5.10.html These were released September of 04 and it was stated
    Quote from: NForce Release Notes
    # Storage Driver Improvements:
        * RAID Morphing
        * Improved RAID Interface
        * RAID spans both SATA and PATA devices
        * RAID 0, 1, and 0+1
        * Improved handling of various storage devices
    Unfortunately I don't know how to get the correct files to a floppy to get windows to use them in the install process, but hopefully someone here does.
    Good Luck
    Jeremy

  • G550 wont boot after bios update

    Hi i installed Windows 7 on the lenovo g550 and was getting the latest drivers and got the 2.53 bios. i got the message that bios flash was successful and then gave timer till reboot. The power light is on and the fan is spinning but nothing shows up on the screen. Luckily i did backup the bios onto a usb but now how do i go about flashing the old one back on.

    If you have to, just hold down power button until it shuts off.
    Remove battery and wait one minute.
    Replace battery, and plug it in.
    Enter bios on boot and "load default settings".
    If you can't get into bios, post back.

  • Wont boot after windows update

    M y Sateite A305 s6916 wont boot after windows updates tried to install.

    Satellite A305-S6916
    tried .. every option on F8
    Try this. Download a repair disc from here.
       Windows Vista Recovery Environment ISO X64 version (64 bit)
    If you can reach the Recovery Environment by booting that, try the Startup Repair and let us know what happens. Sometimes you need to run it more than once.
       Startup Repair: frequently asked questions
    Also try a System Restore.
       What are the system recovery options in Windows Vista?
    -Jerry

  • Satellite Pro C850 wont work after Bios update

    my satellite pro c850 cd wont work after bios update from toshiba.
    what do i do?

    Saying: dont work you mean it does not power up or what do you mean exactly?
    Did you flash the BIOS properly?
    Possibly something went wrong during the update and this means that ROM module isnt flashed properly
    In most cases a special BIOS crisis disk would be needed to get it working
    Not quite sure if you can get it fixed by your own
    Check this thread. Maybe it helps:
    http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=59637
    Otherwise you need help from authorized service provider available in your country.

  • Problem in booting after bios update

    Originally, it was windows home basic was installed in my laptop. But recently I had installed Windows professional. After installation I have downloaded all drivers which are compatible for my laptop model. After BIOS update installation my pc is not booting up at all. Only power button, WiFi and capslock is lighting. Capslock is continuosly blicking. Even FAN speed gets lowered. I have tried hard reset as well as windows+B comand during startup still condition is same. Please reply me....

    see help 8....
    I am a Volunteer to help others on here-not a HP employee.
    Replies aren't online 24/7 because of Time Zone differences.
    Remember in this Day and Age of Computing the Internet is Knowledge at your fingertips if you choose understand it. -2015-

  • Lenovo w510 will not boot after BIOS update

    Hi, 
    This morning I used the windows bios update utility to update my Lenovo w510 type 4318. Everything appeared to have been successful until the machine rebooted. It froze on the lenovo splash screen with text saying to press the blue think vantage button for more options. 
    I waited a good 30 minutes to make sure it wasn't processing anything before trying again. When frozen pressing the power button cause system to beep two times Pause and beep three more times. 
    Called Lenovo support and was told since out of warranty (2/12) the onlyI option is for paid mail in repair at quoted maximum of $575. Needless to say I was very dissatisfied - and made this clear to support who informed there was no way to escalate and no other options. 
    Does anyone have any other options or ability to escalate this case and keep a Lenovo customer. really disappointed 
    Case #9026SN6
    Btw, reason i updated bios to fix issue with usable ram showing 3 gb. 
    Solved!
    Go to Solution.

    lead_org wrote:
    sometimes it is safer to do the bios update outside of windows environment.
    NEVER use the .EXE method for a BIOS update.  Always use the .ISO and the CD/DVD boot method.  Never update after the warranty expires.

  • Computer will not boot after bios update

    This afternoon I recieved an urgent BIOS update in much the same format as I have received updates from HP for years. It was accompanied with some other non urgent update.
    So I gave  the permissions to make the update.
    I recieved a notice that the update had been successfully completed and the computer said it was restarting.
    The problem is that it never woke up...
    After several minutes I manualy restarted the computer.
    As the boot began I heard three beeps, and then nothing but a black screen.
    I shut down and restarted after several minutes but this time no beeps just black screen.
    I figured that somthing must have corrupted the BIOS
    I began researching what the three beeps mean.  Appearently three different sets of BOIS were used in this model.  Different BIOS have different beeps.
    Well I sure never  thought I would need to write down what BOIS I have...
    In my research I have see referances to holding down certain F keys  for different BIOS options as I start the computer
    If I hold down an F key when I hit the start button the computer emediately shuts off
    How can I get to the BIOS to reset or roll back the update?  What next?

      The box is on the way...
    In addition the the methods outlined in the article The Hp tech  had me try to start tapping the F 10 key.
    Nothing worked...
    Hp is sending me a box to return the computer to a repair facility.
    Thank you for your  timely assistance,
    Sparks

  • T500 takes 15 minutes to boot after bios update

    symptoms:
    it takes around 10 or so minutes to get to the thinkpad press f1 to set up screen, after that it gives me a screen that says ME is initializing, this is after a bios update and subsequent roll back of the bios. both bios updates now give me the same result. sleep functions also seems to not work, once im into windows my t500 operates as usual.
    what I've done:
    in addition to rolling back the drivers Ive disconnected /reconnected the cmos battery and turned off AMT. ive also made sure that all of my drivers are up to date.
    machine is a 2081-cto running on win7
    anyone have any idea what i can do? i still have a long warranty but would like to solve it myself so i dont have any down time.
    Solved!
    Go to Solution.

    Hi guys and welcome to the forum, dinny.
    You might try fiddling with the BIOS setting for the security (TPM) chip:
    F1 at boot to get to BIOS setup, then Security, then Security Chip.
    I have mine set to "Disabled" but have seen other reports that setting it to "Enabled" can cure bootup delays.
    Worth a try, please let us know if it helps you.
    Good luck,
    Frank
    Results of Your Ideal Business-Class Laptop survey, concluded 2009-07-29.
    Did someone help you?
    Say thanks! with a kudo.
    Even better: Pay it forward, help someone else.

  • Satellite Pro L300 will not boot after Bios update

    Help please.
    I have just formated a Satellite Pro L300 laptop.
    I used all the updated drivers from Toshiba and all went very well.
    I then updated the bios with the latest version.
    After doing this the laptop will not boot but just keeps scrolling through the start menu and no matter what option I choose it just keeps doing the same thing.
    Any ides welcome

    Hi
    I used the Microsoft installation disk but just keep getting to the same stage until the blue screen appears. I have tried different installation disks and also changed the hard drives as well. I can do everything in bios, change boot device enable or disable devices but that is it. I have tried a few times to instal windows but it just stops at the same point saying windows is stopping instal to protect the system. I fear the bios update has done some permanent damage as I cant get past the dreaded blue screen.Thanks anyway

Maybe you are looking for