Z68-GD55 (B3) won't go to S3 sleep

Just put together a new PC and I am having an issue with sleeping... the computer won't go into S3 sleep mode.  It'll do S1, but as soon as I change the BIOS setting to S3 and try to sleep it, the screens dim momentarily and it looks like it's about to sleep, but it immediately wakes up.  I've used the powercfg command to see what woke it up, and it says that it never went to sleep in the first place!  I've followed all the suggestions on the web about disabling devices (I even went so far as to disable every single device listed that could wake it) and it still refuses to sleep.  So I don't think it's a device waking it.
Any ideas?

In your BIOS set your Internal PLL Overvoltage to disabled and retest. It is directly linked to S3 states and has been found to interfere with Sandy Bridge MBs ability to recover from that state.
Try that, and if that does not solve it, or your's is already set to disabled, then advise MSI technical >>How to contact MSI.<<
Have you tested this with a generic KB and mouse ?
Which BIOS do you curently have ? There have been BIOS releases that solve certain KB and Mouse problems caused by some models.

Similar Messages

  • Memory RAM upgrade won't wake up after sleep mode

    i just recently purchase a pair  16GB RAM of crucial  CT2K8G3S160BM for newegg.com. Yeesterday i try put this on my macbook i7 intel 2.9 processor that crucial said is compatible. but found out everything was good until i close my mac lid for hibernate. What happen is, it won't wake up no matter what i do until a way of reset SMC. BTW i try stick by stick to plug in together with my original 4gb RAM together found out 1 was ok and other one was not. But somehow why the info of hardware show that memory ram 16GB was installed and was OK. Everything was run smooth even booting. The only problem is won't wake up after sleep mode. I already try reset smc, pram, delete startimage, delete powermanagement.file and also sudo hibernate 0-7. Did anyone had this same issue of me. I'm my curiousity will it be the bad ram or software problem.

    i just google around and found this two both crucial ram. Both spec are the same but different model no.
      CT102464BF160B 16GB  and mine is CT2K8G3S160BM are this 2 same? but both same spec.
    http://www.bhphotovideo.com/c/product/877010-REG/Crucial_Technology_CT102464BF16 0B_16GB_2_x.html
    http://www.bhphotovideo.com/c/product/889298-REG/Crucial_CT2K8G3S160BM_16GB_2x8_ 204P_SODIMM.html

  • Why won't my Mac Pro sleep after Lion is installed?

    Why won't my Mac Pro sleep after Lion is installed?

    Tell us, what hardware add ons?
    old software? that required PowerPC/Rosetta maybe.
    Look for any apps, process that used powerpc and look for updates, check out RoaringApps for a table of Lion compatible programs
    does it happen iwth a clean install?
    how about if you do a Safe Boot?

  • I have recently upgraded and am finding my iMac won't wake from a sleep state 80% of the time. What do I need to change or do to prevent this?

    have recently upgraded and am finding my iMac won't wake from a sleep state 80% of the time. What do I need to change or do to prevent this?

    Hi 02SilverSport,
    Try using the power button to wake the iMac.
    OS X Mavericks: Using the power button
    http://support.apple.com/kb/HT5869
    If you are using a wireless keyboard or mouse, check out this article:
    OS X Mavericks: Wake your computer with a wireless mouse or keyboard
    http://support.apple.com/kb/PH13997
    And for more generic troubleshooting, try this one:
    OS X: When your Mac doesn't sleep or wake
    http://support.apple.com/kb/TS5357
    where there's a section for "Your computer cannot wake from sleep" and "Your computer is slow to wake from sleep".
    Best Regards,
    Nubz

  • Won't wake up from sleep mode

    I have only had my iMac for a couple weeks and four times now it won't wake up from sleep mode. I have to use the on/off button for a response.

    Since you have a new machine, I would call Apple immediately and have them deal with the problem.

  • New MacBook Pro won't ake up from sleep with Express Card in it.

    My Mac won't come out of sleep if there is an express card in it. If I hit the power switch both screens light up but the mouse and keyboard are unresponsive. My only option at this point is to hold the power switch and (to quote Moss) "Force and unexpected reboot".
    It also locks up if I power off and remove the card while it is awake.
    Any help would be appreciated. If the answer is to load the next version of the OS to be released this month, I'll do that.

    I have the same problem....MBP not waking from sleep with SIIG 2-Port ExpressCard installed....
    10.4.10 etc..... Same thing happened with 10.4.9
    I'll have to try the "Turn Power Off" command from the menu bar to see if that helps. But I just figure on having to do a funky restart if the machine goes to sleep on me.
    Usually I'm editing and having the Energy Saver set to "Never Sleep" because that screws up editing software. But when I'm not editing....sleep my pretty!

  • Help my itouch's screen won't respond to home & sleep/wake button

    Hi guys need your help, My itouch's(4th gen) screen won't respond to home & sleep/wake button. also the device is on cause when I try to do screen capture the shutters do come off.I've also resetted it a couple of time, tried to drain it and charge again do instruction given by some of the community people has said and still it did not it so please if you can help me
    I've tried these already; If you can't update or restore your iPhone, iPad, or iPod touch - Apple Support, iOS: Not responding or does not turn on - Apple Support,https://geekindisguise.wordpress.com/2009/07/16/how-to-put-ipod-touch-iphone-int o-dfu-mode my ipod is not responding to anything the screen remains black and i cant restore it
    ps don't know if I've really done some of it cause I can't see a thing in the screen

    I think you tried everything here except the trip to the Genius Bar
    - iOS: Not responding or does not turn on           
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable                     
    - Try on another computer                                                       
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     

  • X1C won't wake up from sleep mode using keyboard

    Hi...so finally got my X1C today. One thing I am noticing is that the machine won't wake up from sleep mode when I press any key on the keyboard -- it only wake up by pressing the power key. This is a bit unexpected to me. Is it by design, and is there any way to change this?
    Thanks for your help.
    Solved!
    Go to Solution.

    Does it awaken from stand-by if you press the Fn key? That's been the ThinkPad standard for as long as I can remember.
    Regards.
    English Community   Deutsche Community   Comunidad en Español   Русскоязычное Сообщество
    Community Resources: Participation Rules • Images in posts • Search (Advanced) • Private Messaging
    PM requests for individual support are not answered. If a post solves your issue, please mark it so.
    X1C3 Helix X220 X301 X200T T61p T60p Y3P • T520 T420 T510 T400 R400 T61 Y2P Y13
    I am not a Lenovo employee.

  • Macbook Air 2011 won't wake up after sleep

    My Macbook Air 13" 2011 won't wake up after sleep.  I've taken it to apple genies bar, but they offered to replace my logical board!
    I bought the Macbook Air in last August.  Why cannot they replace a new laptop???

    One thing you want to do is "Repair Permissions" in Disk Utility before you upgrade to a new revision, and afterward do the same thing.
    On occasion files will become inaccessible to the logged-in user and cause certain components of the OS from acting cooperatively. This can most often happen during/after an update. Also, by resetting permissions before an update, it is to ensure that the update process itself can accomplish all tasks.
    You may also want to consider applying/re-applying the downloaded 10.7.3 "Combo Update" from the Apple.com/downloads/ section. After resetting permissions, of course.

  • 1G iTouch won't wake up after sleep

    1G iTouch won't wake up after sleep. When I plug it back into my laptop it does a complete reboot. Tried both reset and restore. Works fine as long as plugged in. It shows a full battery and drains properly but once it goes to sleep it acts like battery is fully discharged.

    Is the iPod or the laptop going to sleep?
    I can't tell for sure from your post.
    When you restored, was it "as a new iPod" or from a backup?
    What software is on the Touch?
    Scott

  • MacBook screen goes gray and won't wake up from sleep - 10.6.2

    We have a MacBook Alum running 10.6.2 with 4gb ram.
    We recently upgraded to 10.6.2 from Leopard and this issue started to happen.
    It seems that as the MacBook goes to sleep or goes to the screensaver mode, the screen goes gray and won't wake up from sleep or screensaver mode without a hard reboot.
    Is Apple aware of this issue? It did not happen with the previous version of Leopard. This issue arrived when we upgraded to Snow Leopard. Other than the sleep issue, SL is rock solid. Kudos to Apple for producing a great OS!

    Hi GrooveDaddy,
    Have you contacted AppleCare via telephone to make them aware of this issue? It definitely doesn't sound like normal behavior. What sort of troubleshooting have you done so far on the issue? What sort of settings do you have on your screen saver? Password protected? Custom iPhoto slideshow?
    What if you manually sleep the machine by closing the lid or engaging it via software (via the Apple menu) does the screen have the issue in both scenarios?

  • G3 Bronze Keyboard won't wake up from sleep

    I have a hand-me-down Powerbook G3 Lombard 400 Mhz (bronze keyboard), with a dead main battery. It works great with the power adapter, and has just enough charge for me to move it from one outlet to another without shutting down. I'm trying to set it up for use as an Itunes server connected to my home stereo, which is fine because it will always be plugged in.
    The problem is that the laptop won't wake up from sleep. This morning I noticed that the display and HD seemed to be sleeping, but the fan/processor buzzing noise was still going (there were no lights other than the little green light on my PCI card). I couldn't figure out any combination of keyboard or power key strokes that would either wake it up or shut it down. I unplugged it, waited half an hour or so, and it finally shut down. I then plugged in, hit power, and it started and booted perfectly (after the expected disk check for abnormal shutdown). Then this afternoon, the whole thing was sleeping (I think -- no sound, no lights other than PCI card light), and again it wouldn't wake up. Again, I unplugged, let it power down (waited for the PCI light do die), the replugged and it started up just fine.
    Any idea what gives? Or what I do when it's sleeping? Right now, I have changed the power saving settings so that it never goes to sleep, but I'd really like to let it sleep when people forgot to turn it off...
    thanks!

    aldpol,
    There are many causes for sleep issues and you just have to wade through them one at a time.
    You can always force a Lombard or newer powerbook to shut down by pressing/holding the power button until it turns off. As you have noted, this is an undesirable process since you can corrupt the HD.
    I would start the troubleshooting in this manner:
    1. Unplug all peripherals (PC cards, mouse, everything).
    2. Reset the power manager:
    http://support.apple.com/kb/HT1431?viewlocale=en_US
    3. Now put the powerbook to sleep via the Special menu, wait a minute or so, then wake.
    4. If no success, restart while pressing the shift key until you see the message 'extensions off', then release. Now test sleep/wake.
    If number #3 is successful, one of you peripherals is probably the troublemaker. If still having issues, please post back with more details if possible.

  • Iphone 4 just turned itself off, won't turn on again - sleep/wake button hasn't worked for a while - tried charging (even though it was 50% charged when it shut down) and that makes no difference....tried usb to computer and directo to wall socket. help?

    phone 4 just turned itself off, won't turn on again - sleep/wake button hasn't worked for a while - tried charging (even though it was 50% charged when it shut down) and that makes no difference....either via usb to computer and direct to wall socket. Any suggestions...other than heading off to the genius bar tomorrow?

    Well, the sleep/wake button is also the power button. If you cannot use it to turn on, then you cannot use it to perform a reset by holding it and the home button together until you see the Apple logo.Those are the only two ways to turn the device on. You can try letting the battery go completely dead and then trying to plug it in. After it has charged for 20-30 minutes, the device may come back on. But, without the sleep/wake button, there is no other way to turn the device on or off.

  • Powerbook G4 won't wake up from sleep

    My 4 1/2 year old powerbook G4 won't wake up from sleep anymore. After I close the lid, or even manually put it to sleep, I can still hear the HD run. The backlight on the top of the lid never lights up and when I open the lid the blank screen doesn't do anything. The only way for me to work around this issue is to power down the laptop and start it up again. Since I've been having this issue every program that I use take forever to load. The spinning color wheel is the bane of my existence! I tried resetting the PRAM, I used Onyx to repair file permissions, and am out of ideas. Any help would be greatly appreciated.

    How incredibly strange. I am having exactly the same problems with my computer. I just started the same behavior today. I have tried using MacJanitor, repaired permissions, verified disk, but it still will not go to sleep properly. S.M.A.R.T status is verified
    I have tested my RAM as described above with no problems surfacing. Anyone else have any ideas that we can try. When I get home on Sunday I will try some more intense investigative tools including re-installing OSX 10.5
    By the way, I am running 10.5.4 on a 15" 1.5Ghz G4 Powerbook with 1.25GB of RAM and 28.9GB harddrive free.
    Another strange thing I have also observed is that it now takes 10 minutes to start up. 5 minutes on the Apple screen with pinwheel, and then 5 minutes with the blue screen before the cursor appears. After that point startup is normal. Also, even though Disk Utility shows 28 GB free on my harddrive when I try to copy something, it says that I do not have enough free space on my harddrive.
    Do you suppose this means that my harddrive is on the way out? Is this also the case of the original poster?

  • My mac won't wake up from sleep, what can i do

    My mac won't wake up from sleep, what can i do

    Can you say more about thermal cut-off?  My mac has beene having problems waking from sleep and I have noticed that I hear the fan running ever so slightly in the background.  When I depress the power button for a second the fan shuts off. 
    Just open the side an dlook to see which fan it is.  The lower fands are easy to see as well as the video card fan.
    When you push the power button and that fan goes off is the machine now fully off?  No power light?  No fans spinning?   Now drives spinning? 
    I don't recall what I did when my machine shut off with the one exhaust fan running.  I think the obvious thing I would have tried would have been to push power button for 10 seconds to shut it down fully.  That or actually pull the plug.
    When this happens the only way to use my Mac is to restart via the power button.
    Then I guess that answers the first question.  It must have turned off since pushing the power button again was the normal reboot.
       I can't find any helpful info on thermal cut-off so I was wondering if you could explain what it is, what causes it, and more importantly what I can do to fix it?
    That was my term for it.  What else could it be?  Without its fan video card would get extremely hot and throw off all that heat.  Whats the point of having temperature sensors in so many places other than to use that info to protect the machine against damage due to overheating?  So my assumption was card gets hot, sensor (probably the pci slot 1 temperature sensor) senses it, kills the machine.  It's also seems logical to me that the circuit(s) handling temperature overloads would want to keep a exhaust fan running to dump the heat out of the machine to further protect any damage from the heat.

Maybe you are looking for