09 inspection lot not getting generated

Hi Friends ,
I have one material batch for which next inspection date is 7.6.2014 . I have activated 09 inspection type in material master . Now when I am executing QA07 for the material  with checkbox " To insp. stock at lot creation" selected and with initial run in days = 4 . System shows following msg in green :
"No batches found for processing"
But it should create a lot for the above batch because inspection date is 7.6.2014 . Stock also exist
Regards

Please go through the following steps & maintain the same
> Batch management should be active against material.
> Next inspection date should be maintained.
> Inspection interval should be maintained according to next inspection date.
> UD must be completed for the previous inspection lot.

Similar Messages

  • Inspection lot not getting generated for schedule in stability study

    Dear All,
    Need your urgent help to solve a issue. I need to perform inspection of material after specified interval of time for which i am using stability study process. Following are the steps which i have followed :
    1) Create initial sample (physical sample created)
    2) Confirm initial sample
    3) Initial test inspection lot( Inspection lot created )
    4) Complete initial test
    5) Specify storage conditions (Physical sample created with CRTD status)
    6) Create testing schedule( Maintenance schedule is created )
    7) I have scheduled maintenance plan through IP10 tcode. All the calls are getting generated.
    Now i have given manual call in IP10, but inspection lot is not generating.
    Please help to solve this issue ASAP.

    Dear Craig,
    Yes i have activated inspection type 16 to material master.
    Actually issue is solved now, I have missed one step " Store stability Sample".
    Now the lots are getting generated.
    i am closing this thread now.

  • Inspection lot not getting generated by Z inspection type

    Hi,
    I created a inspection type Z1 , copying the inspection type 01. I guess I maintained all the required configurations or conditions.
    I maintained the inspection type Z1 in the QM view of a material with status Active, but I am not able to do MIGO, neither the stock type is coming as Quality Inspection automatically in both the Purchse Order creation and MIGO. As a reslut, the inspection lot is not getting generated.
    I am also not able to create a manual lot but QA01, Its giving error as "Inspection type Z1 not maintained for material X" .
    Thanks in advance for your valuable suggestions.
    Regards
    Kunal

    Dear check preffered inspection type in material master QM view and do the GRN.
    Check and Revert.
    Cheers
    KK

  • Inspection lot not getting generated after PurcGR

    Hi,
    Inspection lot not generated after doing GR for a purchase order. what could be the reasons?
    for the first 2 puchase orders, Inspection lot was created. however, for the 3rd Purchase order of 100qty, i did GR for 50 qty only. after then for new purchase orders, the material status has become unrestricted and directly going to stock.
    Inspection type 01 is mainted in material master
    QM info record has been maintained.
    please clarify

    Hi Nagaraj,
    Try the following.
    1. Check the inspection set up in the Material Master record for inspection type 01 whether 'post to inspn stock' is selected. If not, select it.
    2. Check in Customizing for 'QM in Procurement' in 'Define QM system' activity, 'certified QM system - skip' is marked(Actual QM system). If this indicator is selected no inspection lot is created even if there is an active inspection type. This is valid if you maintain a target QM system in QM view of Material Master (Purchase data).
    3. Check in IMG set up :
    Quality Inspection -> Inspection lot creation -> Inspection for goods movement  - whether inspection lot origin 01 is specified for movement type 101 and also ensure that QM is active for this movement type.
    Please revert after trying these options.
    Regards,
    Swati

  • Inspection lot not getting generated during SD delivery

    Hi QM experts,
    I am working on QM in SD function. I activated inspection type 10 in the material master in QM view as shown below.
    I created a QM info record SD through QV51 for the combination of customer and Sales organization and assigned the material and quality inspection as before delivery as shown below.
    Now I created a sales order for the material with sales organization and when I making the delivery system is allowing delivery and no inspection lot is generated and delivery is also not stopped. am i missing something..can u please guide..
    Thanks
    Kumar

    Hello,
    You have activated 10 and 11 both , any specific reason ?
    If you activated 10, then system will allowed you delivery check QM customization---> During Shipping. have you assigned inspection type against Delivery type in customization ?
    Regards

  • Integration with EWM-Inspection lot not getting created

    Hi,
    Inspection lot not getting created after GR is done.
    The scenario is Storage location is connected to external warehouse management,so after the GR is done in the legacy system via interface it is updated in ECC.so while checking the material document inpection lot is not created.
    Can anyone please tell me the necesaary check points and integeration steps  between WM and QM in this case .
    Thanks in advance.......

    Hi,
    Since you didn't say much, I assume you are creating stock into ECC via LSMW using 561 movement. Now to get inspection lot for these batches/ docs, you need to activate inspection type 05.
    Go to material master QM view, assign and activate inspection type 05.
    Additionally, create a respective inspection plan/ task list for the material(s) to carry out RR and get the consistent inspection lots.
    ntn

  • Inspection lot not getting create for 01 Insp type after Intransit

    Hi Qm Gurus,
    I have a Material 'A' which is producing in the plant IN05 and transferring to IN06 plant. We have Scheduling agreement PO for this. After Scheduling Agreement we are doing Transferring the Goods thro 351 GI Movement type. So now the parts will be there in transit.
    So now when I receive this goods in IN06 thro 101 MT, Insp lot is not getting create, it goes to Unrestricted. If I create a std PO for the same when I receive the goods thro 101, it is posting into Insp lot. But after 351 & if I do 101 material is not going into Inspection. Pls advise.
    I checked the Insp type 01 Active for IN06, Quality info record is fine, Quality plan also fine. Pls let me know whether i am missing something?

    Hi ,
    Please activate inspection type 08 stock transfer ..
    If this inspection type is active then during stock transfer lot gets generated.
    Also check QM active for this perticular movement in custamizing setting.
    Regards
    SANIL

  • Inspection lot not getting created

    Dear MM guru's...
    SUB: Quality inspection lot neot creating.
    when i am do GIR, system is not creating Inspection lot for the material,
    i have maintained the QM view in material master and assigned the inspection type aslo, then why system is not creating an Inspection lot for quality inspection, is there any extra settings need to be maintaied in QM.
    Regards
    SARFRAZ

    There is a small check mark which says "active " for each inspection type you maintained in QM view .Make sure you have checked this .If you have not ,then there is no way a lot will be created .
    Please let me know on any furthur doubts coz as far as i know this is a common mistake every person new to QM does .If this not the issue then get back to me .
    regards
    Naik

  • Integration with QM-Inspection lot not getting creating

    Hi ,
    Inspection lot is not getting created after GR is posted.
    Scenario:Storage location is connected to external warehouse management.
    Can anyone please explain the necessary check points and  Integration steps needed to be followed for inspection lot creation.

    Hi,
    Since you didn't say much, I assume you are creating stock into ECC via LSMW using 561 movement. Now to get inspection lot for these batches/ docs, you need to activate inspection type 05.
    Go to material master QM view, assign and activate inspection type 05.
    Additionally, create a respective inspection plan/ task list for the material(s) to carry out RR and get the consistent inspection lots.
    ntn

  • Inspection lot not getting cancelled after the inbound delivery is created

    Hello,
    The scenraio is like this.
    1. Material was procured in plant A.
    2. Using the stock transfer purchase order, transferred the material from Plant A to Plant B.
    3. Outbound delivery was created, Handling units were assigned and Post Goods issue was done.
    4. As soon as this was done, inbound delivery got created automatically in plant B and Handling units were assigned.
    5. Inspection lot was created with origin "08".
    6. Now I want to reverse all the transactions, so I did as mentioned below.
    7. Handling units were deassigned from the inbound delivery and inbound delivery was successfully deleted.
    8. Now tried to do the reverse post goods issue and got the error "Handling unit XXXXXX cannot be reversed"..Goods movement cannot be reversed for handling unit XXXXX because it has been changed or assigned to object since the last goods movement posting".
    The issue is that as soon as the inbound delivery is deleted, the inspection lot status should change, which has not changed. So kindly let me know how to make the system cancel the inspection lot as soon as the deassignment of handling units is done in inbound delivery or the inbound delievry is deleted.
    Regards,
    Narendra Bora

    Hello,
    Can anyone please reply.
    Regards,
    Narendra Bora

  • Inspection Lot not creating for 657 mvt type

    Hello,
    I am unable to create inspection lot for customer returns. Mvt type used by SD module for customer return is 657 ( to blocked stock). While sales to return order with this mvt type, no inspection lot is getting generated.
    But when returns are done with 651 mvt type (Returns to QI), I am able to create inspection lots.
    Can anyone tell me how to activate inspection for 657 mvt type as I want this stock to go directly to Blocked stock.
    Thanks in advance.
    Jason

    Dear,
    Quality inspection stock (movement type is  655)
    Blocked stock (movement type 657)
    If the given quantity is posted to blocked stock returns first, you can make a manual goods movement posting in the Inventory Management component to transfer the quantity to valuated stock.
    Tcode vov6 - there will be schedule line category DN.
    go to details of DN.In Business data,check which movement type is assigned here change it to 655 and try.
    Also go to material master, select "Quality Management" view and execute. There click on "Insp.setup" and press "F5". Assign "06" under tbe tab "Inse.Type" and save.
    Now if that material returns from any customer, the stock will be blocked for quallity clearance. Only quality people can give clearance for that material.
    Regards,
    R.Brahmankar

  • Inspection lot 03 type not get generated

    Dear All
    I have set 03 inspction type in material master and checked lot origin of 03 in configuration also there with N task list type is assigned. but problem is inspection lot not genrated when i realsed production order,
    what should i check to find out this cause
    Regards
    Pravin

    I
    Dear
    I tell you the scenario,
    As here in prodution, they combine number of orders having  same material no.  into One Comboorder having different Order type for ex combo order having ZCOM order type and child order having PP04 order type.
    For Ex
    Combo order(50025)
            i
            i
    i              i                  I
    10029    10030        10031
    as given above structure
    we have developed on Z transction which combine all child orders and made one combo order with total of three, but order type of combo order is different and child orders having different order type.and when combo order released child order also get released but problem is inspection lot generated for combo order only  not child orders
    what would be the reason
    Regards
    Pravin

  • Inspection Lot not generated, with MIGO 561

    Hello All,
    Please help me with this issue.
    WHen i do MIGO with 561, inspection lot is not generated.
    So there is a setting in spro, if we check that, inspection lot wont be generated.
    So now in my IDES, i tried to uncheck that box.
    When i save this setting, I get the following error.
    "Fill table key for table T156Q only up to position 010".
    Please help with this issue.
    Regards,
    Piyush

    To load initial inventory in Quality stock and release it using Inspection lot  UD,   use movement type 563 instead of 561.
    With 561 movement stock is directly posted to un-restricted status. So there is nothing to be released from Quality stock.

  • Inspection lot not generated after goods reciept?

    Dear SAPIENTS,
    Inspection type 01,0101,08,89 and all activated in material master but then allso inspection lot not generated after goods reciept. Can anybody suggest here that what could be the reason.
    Regards,
    Kaushal Rai

    Hi Kaushal,
    For Inspection lot from GR, 01 Inspection type is enough.
    - Ensure 01 Insp type is active and Post to Inspection stock indicator is active for that inspection type.
    - Ensure the QM is active for 101 Movement type, SPRO>Quality Management>Quality Inspection>Inspection Lot Creation>Inspection for Goods Movements>Deactivate Quality Inspection for a Movement Type
    Regards,
    Keerthi.

  • Inspection Lot not created during GR

    Hi All,
    I have an issue wherein the QM View is not activated during PO creation. This has caused the succeeding Goods Receipt to move the stock to Unrestricted eventhough I have already activated QM.
    How can I rectify this problem that GR for this PO will go to QI and will create inspection lot.
    Thanks,
    Raymond

    Hi,
    Please follow following steps,
    I hope you have now activarted inspection type 01 for the material.
    1. Go to PO with transcation ME22n,
    2. For the matreial , go and change the stock type to Qulaity , instaed of unrestriced.
    3. Save and come out.
    Go and do GR .. Inspection lot will be generated.

Maybe you are looking for