1.4.1 and 1.3.1 blue screen system crash when running slide show

I have a new Toshiba Satelite X200-219 running Vista SP1. I have 30 Gb free space on C: and 4Gb RAM. Every time I run a slide show I get the blue screen of death after about 5 slides. I have swapped the original memory (2 GB) back in to see if it is corrupt memory but get the same result.
Is anyone else experiencing this or are there any known solutions?

temp6, temp7, temp8 are strange.... but because it's impossible reach these temps (+127 and +0) I think those sensors are not used or bad report data
if you think it's a overheating problem, you must log temps (sensord+rrdtool)
so you'll get the latest temps before the PC crashes

Similar Messages

Blue screen of death when running labwindows, pxi chassis, and windows 2000

Hi, when programming under labwindows the software crashes cvi, and windows NT and i get the blue screen of death...usually every hr or so. I checked the hw config and there are no conflicts. Is it normal to share IRQ 9 for all? is there a document that explains the I/O map addresses for the pxi to check for conflicts? I got all NI instruments, but one irig board. Currently only talking to the DMM and the switch.

me also
-win2000
-cvi 6.0
-pxi1006 8176cpu
-dmm4060
-IVI1.83 ,nidaq693,nidmm201,nidmm21
- break program after a nidmmread function
- terminate program
- rerun program
- DMM Blue Screen of Death..everytime
- Make Software User Friendly -
Attachments:
BADDMM.ZIP ‏3 KB

Blue Screen//Computer Crash when my ipod touch 2g 16gb connected to my comp

I get a blue screen with a message,
* STOP: 0x0000007E (0x0000005, 0x00000000, 0xF79417C4, 0xF79414C0)
I plug in my ipod touch and I get the blue screen with my computer crashing following it, any help to fix this problem would be much appreciated because I cannot sync my ipod.

Hello, Welcome to discussions.
You may need to update iTunes, Update Printer drivers and if you have a logitech camera or other digital devices download and update the software for those. Articles below
http://support.apple.com/kb/TS2280
http://support.apple.com/kb/TS1502

My macbook pro freezes and then displays a blue screen with black stripes... do you know what's wrong with it?

My macbook pro freezes and then displays a blue screen with black stripes... do you know what's wrong with it?
I have a two and half year mac book pro... I've had some issues with the screen looking scrambled when I quit certain applications, but now it's turned into something worse. I'll be working on my computer and the thing will freeze. When I force restart, the first screen, the apple logo, will be a blue tint and won't boot up normally. Then I try safe mood and it will then boot just fine. But there are blue stripes on my screen. The screen alternates from a blue tint to normal and if the computer freezes again the screen will become completely blue with black stripes. I haven't tried reinstalling my software because I don't have the startup discs that came with my computer. If I was sure that would fix it I would purchase them, but if it's a hardware issue I'm afraid that I'm screwed. I've been able to successfully get the blue off my screen by putting it to sleep and then waking it up, but that's not working well anymore either.
Does anyone else have experience with this? Is it the firmware or what? I have a MacBook Pro from early 2011 and I'm running Mac OS X 10.6.8.
Please help... Thanks!

I just experienced this exact same issue with my early 2011 15" macbook pro. Since like a month after purchasing it I had issues with the screen randomly going dark on me. I sent it in for repair inder waranty they replaced the gpu and logic board but I continued to have the same issues with the screen randomly going black sometimes I would need to reboot it in order to get the screen to go back on but it happened so infrequently and I used the computer for school so disnt find the time to resend it in to apple. Just last night the screen started to display the blue screen with black verticle lines on it. I called apple and explained to them the issues that had been ongoing since I purchased the laptop but they said because I was now outside of warantee that any repairs at thia point wouldn't be covered. Fml so glad I spent 2200 on this future proof macbook pro what a joke my sister purchased a toshiba laptop for 300 4 years ago and it still running like a champ. I loved my macbook but at the price I paid I expect it to last longer than 2 years before leaving me high and dry. *** apple??

After getting the dreaded gray/blue screen, I tried to run disk repair on the internal disk. I got an error message saying "Disk Utility can't repair this disk and restore your backed-up files. The volume Macintosh HD could not be verified completely

After getting the dreaded gray/blue screen, I tried to run disk repair on the internal disk. I got an error message saying "Disk Utility can't repair this disk and restore your backed-up files. The volume Macintosh HD could not be verified completely." What do I do now? This is an iMac and I'm running 10.6.8.

Clean Install of Snow Leopard
Be sure to make a backup first because the following procedure will erase
the drive and everything on it. See below for how to clone a drive.
     1. Boot the computer using the Snow Leopard Installer Disc or the Disc 1 that came
         with your computer. Insert the disc into the optical drive and restart the computer.
         After the chime press and hold down the "C" key. Release the key when you see
         a small spinning gear appear below the dark gray Apple logo.
     2. After the installer loads select your language and click on the Continue
         button. When the menu bar appears select Disk Utility from the Utilities menu.
         After DU loads select the hard drive entry from the left side list (mfgr.'s ID and drive
         size.) Click on the Partition tab in the DU main window. Set the number of
         partitions to one (1) from the Partitions drop down menu, click on Options button
         and select GUID, click on OK, then set the format type to MacOS Extended
         (Journaled, if supported), then click on the Apply button.
     3. When the formatting has completed quit DU and return to the installer. Proceed
         with the OS X installation and follow the directions included with the installer.
     4. When the installation has completed your computer will Restart into the Setup
         Assistant. Be sure you configure your initial admin account with the exact same
         username and password that you used on your old drive. After you finish Setup
         Assistant will complete the installation after which you will be running a fresh
         install of OS X. You can now begin the update process by opening Software
         Update and installing all recommended updates to bring your installation current.
Download and install Mac OS X 10.6.8 Update Combo v1.1.
You may be able to backup your data if you have an erased external drive you can use. Before you do the above but after you have opened Disk Utility you can try to clone your drive:
Clone using Restore Option of Disk Utility
1. Open Disk Utility.
2. Select the destination volume from the left side list.
3. Click on the Restore tab in the DU main window.
4. Select the destination volume from the left side list and drag
       it to the Destination entry field.
5. Select the source volume from the left side list and drag it to
      the Source entry field.
6. Double-check you got it right, then click on the Restore button.
Destination means the external backup drive. Source means the internal startup drive.
Now this will only work if the drive is accessible and can be cloned by Disk Utility. Otherwise, you would need to access your drive from another Mac that you can connect via Firewire - Target Disk Mode.

Each time I open FCPX my mac book pro freeze and I get a blue screen , I am running FCPX 10.08. I experienced that problem since I downloaded some plugins from Noise Industries . Can somebody help me please ?

Each time I open FCPX my mac book pro freeze and I get a blue screen and my mac book is completely frozen...

Have you removed those plugins ? They could be in your Movie folder or Library - application support - FCP- plugins - effects

A request for my admin password keeps popping up randomly and a symbol (5 blue circles surrounding a yellow star) will show in the dock. I haven't typed in my password, just keep cancelling it. itg is called finish_installation.

A request for my admin password keeps popping up randomly and a symbol (5 blue circles surrounding a yellow star) will show in the dock. I haven't typed in my password, just keep cancelling it. The file is called "finish_installation". Also icon is very pixelated. It seems very suspect and I am afraid my mac has a virus?!?!?! Any one? Please help.
I can not find this file anywhere on the system after this request shows up!

Doubtful it's malware ...
Try relaunching the Finder. Press Command + Option + Esc then select Finder in Force Quit window then click Restart.
If that doesn't help, launch the Terminal app located in HD > Applications > Utlities
Copy and paste this command into the Terminal window:
killall Dock then press Return or Enter on your keyboard.
The Dock will disappear for must a moment.
See if that made a difference.

Computer freezes and then goes to blue screen and resets (flash player 10.1)

I have tried to install and reset my Internet explorer several times and still have the same result, my computer freezes and then goes to blue screen and resets. I am running windows 7 64 bit and windows Internet explorer 8. I have tried to go through the adobe trouble shooting and end up with the same problem. Does anyone have an idea were to go from here, this is getting very frustrating.

Do you use the 32-bit version of IE8?
Can you see the Flash animation at http://www.adobe.com/software/flash/about/ ?

IMac G5 PowerPC boots up and freezes at light-blue screen

PowerPC G5 20" iMac, 2.0GHz, +260 GB harddrive, 2 GB of DDR SDRAM
Leopard OS 10.5.6
Computer starts up and freezes at light-blue screen. Mouse still moves, bu no keyboard commands work. Only holding the power button will shut down the computer.
Tried the following:
- Able to boot into Safe-mode only.
- Ran OS Disk Utility to repair permissions and also MacTuneUp 3.6.0, and no change
- Tried changing start-up to boot from OS 10.5.6 DVD and still freezes with light-blue screen. Safe-mode allowed me to run Disk Utility but no difference.
- If I leave the frozen light-blue screen, eventually the iMac power-saving mode darkens the screen, until I move the mouse (then light-blue again and still frozen).
- I left my iPhone connected to the iMac, and when starting up the computer the iPhone started charging. When the light blue screen froze the iPhone stopped charging.
- tried starting computer with Options + Command keys
- tried + Options-Command-P-R untill you hear two beeps: Reset NVRAM (restart 3x)
- tried Resetting the SMU > Unplug all cables from the computer, including the power cord. > Wait 10 seconds.> Plug in the power cord while simultaneously pressing and holding the power button on the back of the computer. > Let go of the power button. > Press the power button once more to start up your iMac.
Questions:
> When booting from OS 10.5.6 DVD, Should I run Time Machine Restore system from Backup?
> I can work fine in Safe-mode all day, but limited resources. Is this a software or hardware issue?

Based on what you have you tried I would guess it is hardware problem.
First iMac's without camera and with GeForce FX 5200 graphics card are known of having capacitor failures which can cause the machine either to become unstable in different situations or fail to boot up at all. I have repaired many of them and changing capacitors brought completedly dead iMac (no power, no nothing) up to life so capacitors mean a lot.
Second and third it's mainly the graphics card which fails, causing the machine to fail to boot, become unstable or boot with artifact patterns in picture.
There has also been power supply issues and Apple did issue a recall back then, I think you can still find article about it and check if your machine has serial number which fits to that recall problem. This way you could check if you should suspect power supply going bad.
Capacitor problem is usually easy to identify (open up the case and look if those can-like things are bulging or swollen) and quite easy to repair if you have bit experience in computers and soldering, iFixit.com provides great disassembly instructions. Graphics card problem is harder to identify because in that case it is the solder which breaks under the graphic chip so you cannot actually see the defect. It is also harder to repair atleast if you want the machine to work long time after that repair. Basically you would need to heat the GPU enough to reflow solder connections.
Because the machine can boot into safe mode I'm suspecting that you have some of these issues I described, safe mode does not utilize hardware at full power and disable full graphics acceleration for example.

Why is Encore 6.0 giving me the "blue screen of death" when I try to create a menu?

When I purchased my student edition 6.0 (which I love by the way), Encore did not have any of the libraries loaded up on it. After reading some discussions, I downloaded the missing folders.
Now, when I try to create a menu, my computer shuts down and gives me "the blue screen of death" as they call it (a blue screen with white writting, counting up to 100%, and saying Windows is preparing to crash...or something about the hard drive crashing....I can't remember because it goes off the screen so quickly).
I've done this several times - my computer only does this when I try to create a menu in encore, and not in any other part of encore. It hasn't happened in any of the other programs either (Premiere Pro and Audition are the only other programs I have used so far), or any other times I have my laptop.
Because of this, I am not too concerned since it seems Encore is the problem. However, I do not want any other problems to escalade from this either.
Am I doing something wrong? Can someone please help me? I'm working on my Senior Thesis (a video) this year, and I really really cannot afford to have my computer crash on me.
Please and thank you,
Meghin

Read Bill Hunt on BSOD http://forums.adobe.com/thread/772169
-and an Encore fix http://forums.adobe.com/thread/1060443

Blue Screen of Death when connecting ipod

Ever since the 2.0 update, when I try and connect my ipod about 50% of the time i get the BSOD. What the heck is going on? Is it another 2.0 bug?

The following document is worth checking through:
What to do when Windows XP or Vista computer displays a blue screen error message when syncing the iPhone or iPod touch

Blue Screen of Death When Plugging in Ipod Touch 4g

Hello,
Im reciving blue screen of death when I plug in my ipod touch 4g. I have updated itunes, Drivers, This happens every time and I suspect it happens when my computer says found new hardware reconizing the ipod as a camera because once I pluged my ipod in and it didn't pop up found camera hardware and it worked. So does anyone know how to fix this or disable my comp from reconizing the ipod as a camera? Thanks in advance
p.s im using XP service pack 3

have u tried pluging an other usb (eg mp3 or mem stick) it to ur compuer? is it doing it with these?
if its only doing this with ur ipod try the following
1 go to start menu and in the search box type in usb
look for device manager
2. open the disk drives and plug in ipod touch and removeable disk should show up
3, try usb drives updates
because the ipod has a camera most older computers running xp think its a camera,
if u have and usb mem stick copy ur itunes folder on to it and copy it to a computer running vista or windows 7 and c it its doing it on one of them, if its doing it on one them there may be other hardware isues with ur ipod touch

Blue screen of death when syncing verizon I phone

I receive a blue screen of death when I try to sync my I phone 4 with I tunes on my laptop. The initial sync went fine, I am connected to my Exchange server for email and have downloaded CD's to I Tunes, when I try to sync...blue screen. I have run registry fix and virus programs and have no errors. Does anyone know how to fix this?

The first response was correct, the computer (xps 1210) used a logitech camera driver that I did not recognize so I deleted it. The software was still active and crashed the computer. Fix was reinstall logitech software and driver. Updating the driver would have probably worked. Thank you!

IPad crashes PC laptop with blue screen of death when syncing

I just got a brand new iPad and I cannot sync a bunch of songs or photos without it just completely shutting down my laptop (PC)and giving me the "blue screen of death". I tried reinstalling iTunes, disconnecting any USB connections I may have and completely updating my lappy...but nothing works! Why can't apple just make something as simple as "syncing" work? Do I have to buy a Mac in order for my iPad to work properly?! Please help me out with this syncing problem.

Hello iPadgirl777,
And welcome to Apple Discussions!
First of all, you posted this in the *6th Generation iPod Nano* forum, when you should have posted it in the iPad forum.
Anyways, check out this Apple support document related to your issue.
http://support.apple.com/kb/TS1502
Hope it helps.
B-rock

Satellite A105-S4284 gets Blue Screen of Death when coming out of standby

MySatellite A105-S4284 runnings Windows XP gets a BSOD after coming out of standby or hibernation. With standby, I'll see the login screen where I enter my password, and then it may show the desktop background or even the open app (Outlook or Word, typically) for a second, afterwhich the BSOC appears. For weeks I was getting a black screen sporadically after standby. Researched the problem and saw recommendations to update BIOS. So I updated the BIOS to the latest version, and then I started getting blue screens of death rather than a black screen. Thought the problem was McAfee, because I'd get crashes right after McAfee became active in the background, sometimes without going into standby. Cancelled McAfee, took it off with the cleaner, used Avast instead, and that seemed to help. But then BSODs came back. I uninstalled non-essential software, clearned registry with CC Cleaner, freed up more HD space and defragged, ran SpyBot, etc - but I still get the BSOD almost every time I go into standby or hibernate.
The stop messages on the BSOD don't show a driver. and all begin with 0x0000007E (0x000000C5, ... and then differ after that. One recent one followed with 0x804E13D5, 0xAA6B9B8C, 0xAA6B9888). Does that mean anything?
I've installed Microsoft's debugging tools to look at the dumps after a BSOD. Here is output for two recent crashes. Doesn't point to a driver. NTKRMLMP.exe is what crashes - do I need to replace that from the I386 folder somehow? I did have my Matsu**bleep**a DVD-CD drive suddenly quit a time or two until the computer was restarted. Should I reinstall the DVD driver? Or the graphics driver? Worried that I might break something by doing that.
Loading Dump File [C:\WINDOWS\Minidump\Mini030809-02.dmp]
Mini Kernel Dump File: Only registers and stack trace are available
Symbol search path is: SRV*c:\symbols*http://msdl.microsoft.com/download/symbols
Executable search path is:
Windows XP Kernel Version 2600 (Service Pack 3) MP (2 procs) Free x86 compatible
Product: WinNt, suite: TerminalServer SingleUserTS
Built by: 2600.xpsp_sp3_gdr.080814-1236
Machine Name:
Kernel base = 0x804d7000 PsLoadedModuleList = 0x805634c0
Debug session time: Sun Mar 8 16:05:07.187 2009 (GMT-5)
System Uptime: 0 days 4:22:53.890
Loading Kernel Symbols
Loading User Symbols
Loading unloaded module list
BugCheck 1000007E, {c0000005, 804e13d5, a9860b8c, a9860888}
Probably caused by : ntkrnlmp.exe ( nt!ExAllocatePoolWithTag+7a9 )
Followup: MachineOwner<snip>
SYSTEM_THREAD_EXCEPTION_NOT_HANDLED_M (1000007e)
This is a very common bugcheck. <SNIP>
Arguments:
Arg1: c0000005, The exception code that was not handled
Arg2: 804e13d5, The address that the exception occurred at
Arg3: a9860b8c, Exception Record Address
Arg4: a9860888, Context Record Address
Debugging Details:
EXCEPTION_CODE: (NTSTATUS) 0xc0000005 - The instruction at "0x%08lx" referenced memory at "0x%08lx". The memory could not be "%s".
FAULTING_IP:
nt!IopfCallDriver+2d
804e13d5 ff548638        call    dword ptr [esi+eax*4+38h]
EXCEPTION_RECORD: a9860b8c -- (.exr 0xffffffffa9860b8c)
ExceptionAddress: 804e13d5 (nt!IopfCallDriver+0x0000002d)
   ExceptionCode: c0000005 (Access violation)
ExceptionFlags: 00000000
NumberParameters: 2
   Parameter[0]: 00000000
   Parameter[1]: 00000070
Attempt to read from address 00000070
CONTEXT: a9860888 -- (.cxr 0xffffffffa9860888)
eax=0000000e ebx=00000001 ecx=87546020 edx=853fe1a0 esi=00000000 edi=f772471c
eip=804e13d5 esp=a9860c54 ebp=a9860ca0 iopl=0         nv up ei ng nz ac po nc
cs=0008 ss=0010 ds=0023 es=0023 fs=0030 gs=0000             efl=00010292
nt!IopfCallDriver+0x2d:
804e13d5 ff548638        call    dword ptr [esi+eax*4+38h] ds:0023:00000070=????????
Resetting default scope
CUSTOMER_CRASH_COUNT: 2
PROCESS_NAME: System
ERROR_CODE: (NTSTATUS) 0xc0000005 - The instruction at "0x%08lx" referenced memory at "0x%08lx". The memory could not be "%s".
EXCEPTION_PARAMETER1: 00000000
EXCEPTION_PARAMETER2: 00000070
READ_ADDRESS: 00000070
FOLLOWUP_IP:
nt!ExAllocatePoolWithTag+7a9
805517b9 e9e4feffff      jmp     nt!ExAllocatePoolWithTag+0x7bf (805516a2)
BUGCHECK_STR: 0x7E
DEFAULT_BUCKET_ID: NULL_CLASS_PTR_DEREFERENCE
LAST_CONTROL_TRANSFER: from 804e13d9 to 804e13d5
STACK_TEXT:
a9860c6c 804e13d9 8753d018 853fe1a0 00000000 nt!IopfCallDriver+0x2d
a9860ccc 805517b9 00000000 00000002 00000000 nt!IopfCallDriver+0x31
a9860dac 80575723 a9f4533c 00000000 00000000 nt!ExAllocatePoolWithTag+0x7a9
a9860ddc 804ec6d9 f7720ce2 a9f4533c 00000000 nt!PspSystemThreadStartup+0x34
00000000 00000000 00000000 00000000 00000000 nt!KiThreadStartup+0x16
SYMBOL_STACK_INDEX: 2
SYMBOL_NAME: nt!ExAllocatePoolWithTag+7a9
FOLLOWUP_NAME: MachineOwner
MODULE_NAME: nt
IMAGE_NAME: ntkrnlmp.exe
DEBUG_FLR_IMAGE_TIMESTAMP: 48a4044a
STACK_COMMAND: .cxr 0xffffffffa9860888 ; kb
FAILURE_BUCKET_ID: 0x7E_nt!ExAllocatePoolWithTag+7a9
BUCKET_ID: 0x7E_nt!ExAllocatePoolWithTag+7a9
Followup: MachineOwner
0: kd> lmvm nt
start    end        module name
804d7000 806ff000   nt       # (pdb symbols)          c:\symbols\ntkrnlmp.pdb\B883868B88CB415A92EC010CF6A115A52\ntkrnlmp.pdb
    Loaded symbol image file: ntkrnlmp.exe
    Mapped memory image file: c:\symbols\ntkrnlmp.exe\48A4044A228000\ntkrnlmp.exe
    Image path: ntkrnlmp.exe
    Image name: ntkrnlmp.exe
    Timestamp:        Thu Aug 14 05:09:14 2008 (48A4044A)
    CheckSum:         0021B760
    ImageSize:        00228000
    File version:     5.1.2600.5657
    Product version: 5.1.2600.5657
    File flags:       0 (Mask 3F)
    File OS:          40004 NT Win32
    File type:        1.0 App
    File date:        00000000.00000000
    Translations:     0401.04b0
    CompanyName:      Microsoft Corporation
    ProductName:      Microsoft® Windows® Operating System
    InternalName:     ntkrnlmp.exe
    OriginalFilename: ntkrnlmp.exe
    ProductVersion:   5.1.2600.5657
    FileVersion:      5.1.2600.5657 (xpsp_sp3_gdr.080814-1236)

In safe mode it is not possible to standby. That is disabled. Tried to make it possible with Toshiba's power control service, but it is not available.
In a new account, the BSOD still occurs. I created a new account, logged out of my account, and went to the new one. Tried standby. It came out of standby for a second and then had the blue screen of death.
In checking the event manager, I seen errors shortly before crashes sometimes that involve the CD.
So I went to Toshiba.com and downloaded the DVD RAM driver and ran it, reinstalling the driver, and then restarted. I also saw that there was C-Dilla driver in my drivers. I uninstalled the SafeCast program that I think is associated with C-Dilla, moved the C-Dilla driver out of the drivers to a distant folder, unchecked C-Dilla in MSCONFIG so it won't load (it was still there after removing SafeCast), and then reinstarted. So with a new DVD Ram driver and neutering, I hope, of C-Dilla, I tried things again and the system appeared to be crash free - better than it had been. But then a crash occurred - BSOD - and upon restart, the CD locked up, and crashed again.
After restarting, there was a new dialog that popped up after Windows launched indicating that there had been an error with SONIC DLA. Before the crash, there was an event n the event viewer:
My last error comes from the Plug and Play Manager:
The device 'MAT**bleep**A DVD-RAM UJ-841S' (IDE\CdRomMAT**bleep**A_DVD-RAM_UJ-841S________________1.60____\5&226f6cf2&0&0.0.0) disappeared from the system without first being prepared for removal.
Hmmm. So things are still vulnerable. Any ideas? Buy new CD drive? Or new computer?

1.4.1 and 1.3.1 blue screen system crash when running slide show

Similar Messages

Maybe you are looking for