1 long beep and 2 short beeps

hello this is my second post....before i had problems with me8 bios, then downgraded using this forum tool..thx for that.
now i can boot my PH67A-C43 (B3) board and use it normally, but my problem is that when ever i try to restart or boot it again without waiting i get 1 beep with is normally the one which indicates that system is OK and then 1 long beep and 2 short beeps and no display on the monitor....i can only boot my PC if i let it turned off for 5 or more minutes...this is really annoying!!
specs:
Operating System
   Microsoft Windows 7 Home Premium 64-bit SP1
CPU
   Intel Core i5 2400 @ 3.10GHz   32 °C
   Sandy Bridge 32nm Technology
RAM
   8.00 GB Dual-Channel DDR3 @ 665MHz (9-9-9-24)
Motherboard
   MSI PH67A-C43 (MS-7673) (SOCKET 0)   37 °C
Graphics
   VX2250 SERIES (1920x1080@60Hz)
   ATI Radeon HD 5700 Series (ASUStek Computer Inc)
Hard Drives
   56GB OCZ-AGILITY3 (SSD)   30 °C
   149GB SAMSUNG HD161GJ (SATA)   24 °C
Optical Drives
   SONY DVD RW DRU-880S
Audio
   Realtek High Definition Audio

i heard about the full cmos clear yesterday....after the flash i just pressed the clear cmos button at the back panel...but now i did the full clear...
well i have an aerocool e80 700w psu...i was thinking it might be the psu...then i tried on my old 500w coolermaster psu and it worked fine(i could restart as many times as i wanted/no blank screen)
then i hocked back the aerocool to confirmed if it was at fault and POOOFFFF no more blank screen.i restarted any time with no problem...how can it be?what caused the blank screen and BSOD?
i will try to use the PC as much as i can and see if i get any blue screen...will keep u posted
***memory is Kingston 4*2gb.i ran memtest86 it found no error over 2 hours...i never overclock anything

Similar Messages

T61P died, 1 long beep - 2 short beeps problem - Do the updates from Lenovo KILL our laptop?

Hi all
I bought T61P from 2 years ago, everything is ok until yesterday, I turn on my laptop and nothing display on the screen, and with this : 1 long beep - 2 short beeps....
I make some search, and found a lot of people have the same problem, and almost happend from September - 2009 to now.
I asked my self why this problem does not happend in the 1st year of using T61P...and this only happend from September - 2009 to now? DO THE UPDATES FROM LENOVO KILL OUR LAPTOP?
My laptop is out of warranty, and I hate to replace another mainboard.... If I must do it, I will throw my laptop to the Trash, and never buy another Lenovo laptops.

so far it looks like a strict hardware problem, not related to updates. however, some manufacturers try to "cheat" with bios updates - they make fan to run at higher speed lowering the mainboard temp. This does not solve the problem per se, it just makes laptop survive beyond warranty expiration date, so you, dear customer, will have to foot the bill.

Why my mac beeps 2 short beeps ?

Why my mac beeps 2 short beeps , it happens once or twice or maybe more a day ? Is that means there is a problem with it ?

Perhaps SMC and PRAM resets will help:
http://support.apple.com/kb/ht3964
http://support.apple.com/kb/ht1379
I view that as an 'undesirable' noise. If the above does not eliminate it, my prior suggestion of an Apple Genius bar or AASP appointment is the best option.
Ciao.

Mac Air is dark and emits three short beeps/three long beeps/three short beeps ("SOS"). What does this mean?

Mac Air was left on power attached to a monitor overnight. In the morning there was a message that I had to turn it off by depressing the "on" key for over then seconds. I did this and it would not turn off. It is now emitting three short beeps followed by three long and three shorts ("SOS" in morse code). What does this mean?

http://support.apple.com/kb/HT2538
If what I read is correct, you will need to take your MBA to Apple to have its firmware restored.
I cannot explain why this happened.

On startup, what does 3 short beeps, 3 long beeps, 3 short beeps, and a black screen mean?

On startup, I hear 3 short beeps followed by 3 long beeps followed by 3 short beeps, then nothing. Screen remains black the whole time. Tried to boot holding down option key - nothing. 2010 MacBookPro running Snow Leopard. Any suggestions?

Intel-based Mac Power On Self Test RAM error beeps
Power On Self-Test Beep Definition - Part 2
3 long tones, 3 short tones, 3 long tones: Indicates EFI ROM corruption is detected and the computer is in EFI ROM recovery mode.

RAM Failure? (3 Short Beeps, 3 Long Beeps, 3 Short Beeps)

Anyone have any idea what 3 Short Beeps, 3 Long Beeps, and 3 Short beeps when starting the computer mean? I heard it might be RAM failure? Could that be the case? How much has it been in the past? Computer's a Late 2010 13" Macbook Air with the Core 2 Duo. Thanks.

The following may help: Mac computers: About startup tones - Apple Support

Need help in diagnosing 1 long beep 2 short beeps

I know this usually means video card is bad. I need to know if disconnecting internal video cable on working system will give the same symptom to help isolate problem between display and video card
Solved!
Go to Solution.

not exactly sure; the 1long + 2short beep diagnostic is somewhat generic, it could be almost anything (on the mainboard, including GPU).
and Lenovo ThinkPad Beep Codes and ThinkWiki Beep Codes have conflicting information about the 1long/2short
you haven't said what machine, but assuming it's a T6x series, do you have it docked with an external video card? the onboard GPU is not socketed (it's soldered to the mainboard), so the only way to disable it (that i'm aware of) is via the BIOS (assuming an external video adapter in a dock is also available for further troubleshooting). i don't think that disconnecting the display panel (flat) cable is likely to help diagnose the problem, but while you're at it, you might want to make certain that it is seated/connected properly. i know that where the display cable connects to the socket on the back of the lcd panel is a tight fit, and the connecter itself locks into place (when mated). you've checked the lcd cable for damage and/or proper connectivity, i assume? what about external monitor to the VGA port... have you tried that? FN-F7 key presses may be necessary to toggle the video hardware b/w the internal/external displays.

1 long beep 3 short beeps

My motherboard keeps beeping this message to me and i am wondering what it is saying can anybody help.
I have a k7t turbo model number 6380e so if you can help please answer.

Are you sure K7t turbo with model number 6380E?
Nevertheless, the beep means your display card is undetected or not installed properly. Double check your display card, and make sure it is slotted into the AGP slot fully, firmly. Of course you might need to push a little bit of force towards the motherboard :D
Here is one example, if you're using some Radeon 8500, the DVI-out port is positioned way too low at the bottom, and some casing design might block the card from fitting fully in properly.

Long Description and Short Description

Dear All,
I have a dimension with three levels.
1. District (district_id, district_name)
2. Council(Council_id, council_name)
3. Address(person_id, address, postcode, phone....)
I have set the district_id, council_id and person_id as SHORT DESCRIPTION and the district_name, council_name, and address as LONG DESCRIPTION.
BUT when I view the data (right click dimension -> Data) It shows me the surrogate id (which are negative ids) instead of the Textual fields i.e. district_name, council_name and Address.
Please, tell me how can I see all the textual fields instead of seeing the surrogate keys?
regards
P.S. I am using OWB 11g on SUSE

Hi
OWB provides the mechanics to extract from a bunch of resources, design schemas and models as well as load into them but it is not a reporting tool. The metadata that is used by the OWB data viewer is also used by this excel component and it works right off the database (as far as I remember). This will let you build cool reports right off the bat from the models built and loaded by OWB.
Cheers
David

MicroTower DC5750 AMD ATHLON 64x gives 2 beeps and 9 beeps.

my computer turns off directly while running after 10 minutes giving 2 beeps with red led flashing with beeps once in a second with a gap of two second.and beeps stops after 5th time but led flashing goes on
if I try to restart it by switching off it and switching it back:
after 30 sec: it gives 9 beeps with led flashes the same way
after 5 min : it turns on and works fine. but doesnot work more than 10 to 15 min.
i got over heating problem this is solved now
This question was solved.
View Solution.

Hi:
Please read Appendix A starting on page 56 of the Troublehooting Manual at the link below, for the list of audible beep codes, possible causes, and recommended troubleshooting steps.
http://h20565.www2.hp.com/portal/site/hpsc/template.BINARYPORTLET/public/kb/docDisplay/resource.proc...

My screen is now long horizontally and short from top to bottom.

so now all the cars I search for are long! my friend who is computer savvy tried to help.
HELP,
Stranded in looooongville,
Duckydoodle
PS i still have the buttons at the top.

Try to disable hardware acceleration in Firefox (you need to close and restart Firefox).
*Tools > Options > Advanced > General > Browsing: "Use hardware acceleration when available"
*https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes
You can rename (or delete) the content-prefs.sqlite file to content-prefs.sqlite.old in the Firefox profile folder to reset the page zoom for all websites.
You can use this button to go to the Firefox profile folder:
*Help > Troubleshooting Information > Profile Directory: Show Folder (Linux: Open Directory; Mac: Show in Finder)
*http://kb.mozillazine.org/Profile_folder_-_Firefox

3 short beeps (*not* on boot)

hello,
today my mac mini early 2009 began to beep: 3 short beeps every 15 seconds or so.
i've found searching here that 3 beeps on boot means a problem with RAM, but the curious in my case is that it boots up normally.
the beeps begins a couple of min after i log in.
does this still mean ram, or something else? i couldn't find out.
running 10.9.1.
many thanks,
paula

Go through the below link and according to your Mac model run one of the test to check the Apple Hardware
OS X Mavericks: Use Apple Diagnostics or Apple Hardware Test
http://support.apple.com/kb/PH14291
Using Apple Hardware Test
http://support.apple.com/kb/ht1509
Using Apple Diagnostics
http://support.apple.com/kb/HT5781

Equivalent rect long and short sides

Not so sure if anybody else already came across this problem or not. Any suggestion is welcome.
I have a simple isolated object to be fitted into an ideal rectangle which will then be used for a metrology purpose in following step. I was trying to make use of the equivalent rect long and shot sides from particle analysis operation, but it seems the particle analysis always gives a same value to the long side and short side. Attached picture shows the calculation results from vision assistant. I tried to calculate the equivalent rect sides from the given area and perimeter. The results tends to become complex values as the perimeter seems smaller than it should be(i.e.. P^2 smaller than 16*A). It may be one reason to produce same value to equivalent rect long and short side.
PS: the expression for calculation of equivalent rect long and short side in the page: http://zone.ni.com/reference/en-XX/help/372916L-01/nivisionconcepts/particle_measurements/ seems not right. It should be (P-sqrt(P^2-16A))/4, rather than P/4-sqrt(P^2-16A).
Attachments:
results from vision assistant.jpg ‏131 KB
ROI.jpg ‏8 KB

Hi paris_sun,
I am assuming you are using the latest version of Vision Assistant 2011 SP1.
I would just like to clarify what you are trying to achieve. This is to measure the long and short (length and width) side of a rectangular shape in your image by using:
Processing Functions: Binary >> Particle analysis
Something I could suggest is to play around with a more definative rectangle and see if this helps. I have tried using a rectangle and the measurements have come out fine.
The shape you are measuring happens to have the same size dimensions i.e. a square.
Where are you acquiring your image from? And are you expecting it to be a square?
With regards to the formulas being incorrect I will look into this for you.
Kev R
Kevin R
Applications Engineer
National Instruments UK&Ireland
Attachments:
NI Vision Rectangle.jpg ‏373 KB
Rectangle.jpg ‏8 KB

T61p exhibiting 1 long and 2 short beep and black screen

All,
There have been multiple discussions over the past months concerning a 1 long and 2 short beep symptom on some T61 and T61p model systems. Over the last several weeks members have begun to start additional topics on this theme and cross post between threads.
I am consolidating all the threads into this new discussion today. Since many of these discussions were originally parallel, the dates and some of the context will now appear somewhat out of chronological order. Please keep that in mind while browsing this thread.
If you are presently experiencing the 1 long and 2 short beep code with a black screen on boot up, I would recommend that you contact service at this time for assistance.
UPDATE 1/4/2011
Previously, I have advised customers to contact service for assistance with the symptoms discussed here. In an effort to maintain customer satisfaction and loyalty, Lenovo has repaired a number of systems as post warranty exceptions. Lenovo will continue the post warranty support; however, with some revisions to the extended coverage effective December 31, 2010.
Customers who experience these symptoms on qualifying models that are no more than six months beyond expiration of warranty should continue to contact support for assistance. This additional coverage ends March 31, 2011.
Coverage beyond this date is available under the terms and conditions of extended warranty or maintenance agreements. Warranty extensions may be purchased for systems that are still within the base warranty period, and post warranty maintenance agreements may be purchased to provide coverage after base and extended warranty periods have expired. Extended warranties and maintenance agreements are a great way to ensure coverage for all the major system components.
Best regards,
Mark
ThinkPads: S30, T43, X60t, X1, W700ds, IdeaPad Y710, IdeaCentre: A300, IdeaPad K1
Mark Hopkins
Program Manager, Lenovo Social Media (Services)
twitter @lenovoforums
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество
Solved!
Go to Solution.

2 is a coincidence, 3 is a pattern... and your problem is identical to mine, too, and happened just some days after mine did...
It seems to me, without wanting to be alarmist, that the T61p with the 570M gpu (or a batch of them) is failing with the same exact problem (1 long 2 short = GPU error) at the exact same time... scary thought, really.
Mine arrived at the lenovo repair center (it's still on warranty) on wednesday, and the status shows as "Repair complete, shipped to customer" as of yesterday. There is no tracking number or "Failing Element / part number" in the status page, tho. It hasn't arrived, either.
Do you know your planar card / motherboard part number? It would be interesting to know if it's the same as mine (42W7653). Were you affected by the problem shown at http://forum.lenovo.com/lnv/board/message?board.id=T_Series_Thinkpads&thread.id=30460&view=by_date_a... ?
And once Mark_Lenovo reads this, Mark, do you need any info? (serial number for the laptop, easyserv reference, etc?)
EDIT/UPDATE:
I called the EasyServ warranty customer support to ask if they had any additional info not in the website, and as a matter of fact they do. The (very, very helpful and nice) man on the phone told me that the motherboard had been replaced and the laptop was due to arrive today, and he gave the UPS tracking number for it, which indeed says it's scheduled to arrive here today, at some point.
Once it's here I'll update with information about the actual repair and the part number of the new motherboard, etc.
To be honest I'm more than pleasantly surprised about the service: the box for shipping my laptop arrived on wednesday, it was picked up that very same day, the laptop was repaired on thursday and arrives to me today, friday. If the laptop works as expected, this is a 10 out of 10 for lenovo customer support, at least for me.
I'm less-than-happy about the quality of the product, of course, but at least I got the 3-year warranty so lenovo paid for everything.
Message Edited by Kry on 04-10-2009 01:18 PM

Won't start up - 3 long beeps and 1 short beep repeated

As I was watching Netflix, the display went crazy and displayed horizontal lines and the computer froze.
I held the power switch down to shut it off.
After restarting, seemed to work fine for a few minutes, then same thing happened.
Reset again. Seemed to start up fine (heard the chime and the hard drive going) but no display output.
Reset again. Got the start up chime, a white screen with horizontal lines, and I get 3 long beeps and 1 short beep repeatedly.
Any ideas?
Thanks for your help in advance.

The beeps you're hearing means the system has no usable memory. You can try reseating the memory or swapping for other known working memory (pain as it is to open the mini up). Otherwise, typically that means it's new logic board time. See this Apple article: http://support.apple.com/kb/HT1547

1 long beep and 2 short beeps

Similar Messages

Maybe you are looking for