1 PUB + 2 SUB and route list fails on 2nd SUB
Hi Guys,
Hope someone can help me here it might be something I am over looking.
I have a Publisher with 2 subscribers. All phones registers on my 2 subscribers and the Pub does only my gateways and call processing.
On my route lists when it registers on my 1st sub the branch from that spesific route list can receive calls but cannot make any outbound calls. They just get a fast busy tone. Media resources is not a problem.
Then this only happens as well when I tick run on all active nodes under the route list. It is as if it over writes my Call Manager Group order.
Hi.
When you enable "run on all active nodes" you let the ip phone to use the CUCM where it is registered on to call out.
Verify that on your VG you configured dialpeers for all CUCM nodes.
Here is a very useful doc written by my friend Deji https://supportforums.cisco.com/blog/12088366/sip-trunks-and-run-all-active-cm-nodes
Give a look as far as you can.
HTH
Regards
Carlo
Similar Messages
-
Route-List not using 2nd Route-Group when PRI cable is removed from H323 gw
CCM 4.1.3sr3b
Router - 2811 - 12.4.4T2
1 site with 2 gateways, gw1 and gw2
RL has both gateways as RG's.
If gw1 has its PRI cable removed, CCM RL will not pass call into gw2 - Not working.
If gw1 is turned of/Ethernet removed RL will wait the h323 timeout before passing call to gw2 - Working OK.
Is this how H323 works if the PRI is down ?
I know MGCP would work but is not an option.
I would have thought that the H323 gw1 would report that there are no resources available in the cause code and the CCM when then use the second choice in the RL.
Now, this is a service parameter "Stop Routing on User Busy Flag*" which is set to true, but this only relates to intercluster trunks.
I've tried playing with the few voice hunt command on the router with no luck.
Any advice or pointers.
ThanksYes, saw this next to the user busy flag, but the help says this about "Stop routing on unallocated number"
"This parameter determines routing behavior for intercluster trunk calls to an unalloc ted number. An unallocated number represents a dialed directory number that does not exist in a Cisco cluster. Valid values specify True or False. When the parameter is set to True and a call that is being routed to a remote Cisco cluster through a route list is released by a remote Cisco CallManager because of the unallocated number, a local Cisco CallManager will stop routing the call to a next device in the route list. When the parameter is set to False, the local Cisco CallManager will route the call to the next device."
Again, it talks about intercluster links, I will try on Monday.
Thanks -
I have a Pub and 2 Sub's. Sub #1 is with the Pub, at the main site it is our TFTP server, Sub #2 is at a remote site with about 100 users along with a router and 2 PRI's for outbound calls. We had a network failure between the main site and the remote site and all phone lost their registration with the system until we were able to get the network back up. Currently the network is up in a crippled state on a 1 T-1 link while we troubleshoot the bigger issue with our 6mb pipe, however Sub #2 and its associated router arent talking with the PUB or other Sub. I'm still getting alerts every 30 minutes stating they are the server is down. I'm sure once the network is corrected this will bring everything back on line. My question is how can I prevent in this in the future. I need this site to be stand alone if the network goes down again. I was told by our vendor that if we had a subscriber at each site then we would need SRST licensing. I know something needs to be configured to make it all work, I'm just not sure what.
I already have a group at the site but it includes both the Pub and Sub from the main site as well as the Sub from the remote site. I would only have to remove the Sub from the main site, problem is I currently only have 1 TFTP server it runs on SUB #1, should I make SUB#2 a TFTP server as well and the phones are setup for DHCP at the main site, I'm going to need to have a DHCP server setup at the remote site as well. Correct?
-
Route Pattern Failing to Next Route List
Anyone have any ideas regarding a Route Pattern which is failing to the NEXT Route List available? I am running CCM 3.2(2c).
The Route Pattern looks like 1865.XXXXXXX and fails to the Route List specified. The call completes to the next route list. When I make a route pattern as 1865.6XXXXXX it will fail part of the time. When I make a route pattern as 1865.69XXXXX the call hits the correct Route List every time.
ThanksTry puting the t calling party transform mask on route details of route list.
-
I have a 1st generation apple TV, which was working perfectly until I changed from a Windows PC to a Imac. The Apple TV will not show in Itunes. I have changed the IP address, sub mask and Router IP address. Since changing I have switched everything of and on again. Can anyone help?
I have a new router and computer. I have just remembered that just before my old PC died on me, I transferred my iTunes library to a hard drive. I can't remember exactly just how I got my library back, but there are definately things in my library now that were in my library on my old PC! Hope this makes sense. What do you mean by same location? Do you mean in the same place in the house?
Another difference I have just thought of was my old router was connected directly to the computer bu I have not been able to do this with Sky as my PC is not near a phone socket! Will this make a difference? -
Hi all,
My imac (osx 10.6.8), apple mail(4.5) has begun to act very odd. It quits out and on occasion I open an email to face "plugin is missing" or I have a spinning wheel and the email won't open. New to do list fails to add to the list. Can anyone help?Hi all,
My imac (osx 10.6.8), apple mail(4.5) has begun to act very odd. It quits out and on occasion I open an email to face "plugin is missing" or I have a spinning wheel and the email won't open. New to do list fails to add to the list. Can anyone help? -
Help
WiFi only works close to router, DNS fail, Signal Bars present but Safari says no Internet, I've deleted and re-added through to reset and full reset, I had no problem with 4.3.2 only 4.3.3 both my iPhone4 and my iPad2. I am now beside router - no problem, but go 20 metres and WiFi becomes unstable. Only way to get either to work is disable WiFi either as a Hot Spot or turn it off and use the 3G connection. This worked with 4.3 & 4.3.2 what has gone wrong? I raised it at the Apple Store in Belfast as a problem but was told that there was no problem with Apple but I must have a faulty router - yeah - that's a lot of faulty routers, my home, my office, my holiday home, Starbucks, my friends house, my son's house. I've tried all the 'fixes'. I think it is a plan to force us to buy Apple RoutersTwo ways out, I added two more Belkin Access Points in my house in Spain so that I'm not more than 10Mtrs away, (Reinforced Concrete & solar glass 2010)
I bought 3 Apple Airports, 1 x Extreme and 2 x Express (1 as a hard wired AP, 1 as an extender) for my other house (Brick construction 1930's)
Everthing now works perfectly, as I said 'an apple plot', so either blast them with signal or visit your nearest apple store.
Early beta iOS5 (iPad) is also much inproved in Beta 3, I have not had any problem with 'Lion'
Happy hunting!
john -
Swap roles Pub to Sub and Vica Versa
Hey Guys
Is there a way to swap roles between two CUCM servers in a single cluster?
Pub to Sub and Sub to pub
Could you just do a physical move of the VMs and then re-IP them?
Any idea appreciated, cheers MikeSupported Features of VMware vSphere ESXi, VMware vCenter and VMware vSphere Client
http://docwiki.cisco.com/wiki/Unified_Communications_VMware_Requirements#Supported_Features_of_VMware_vSphere_ESXi.2C_VMware_vCenter_and_VMware_vSphere_Client
Read the above about moving VMs between hosts.
And yes, you can change the hostname and the IP of the servers, but that won't affect their role as Deji already mentioned.
Follow the guide on how to change IP/hostname available on CCO for your CUCM version.
HTH
java
if this helps, please rate
www.cisco.com/go/pdihelpdesk -
Site-to-Site VPN btw Pix535 and Router 2811, can't get it work
Hi, every one, I spent couple of days trying to make a site-to-site VPN between PIX535 and router 2811 work but come up empty handed, I followed instructions here:
http://www.cisco.com/en/US/products/ps9422/products_configuration_example09186a0080b4ae61.shtml
#1: PIX config:
: Saved
: Written by enable_15 at 18:05:33.678 EDT Sat Oct 20 2012
PIX Version 8.0(4)
hostname pix535
interface GigabitEthernet0
description to-cable-modem
nameif outside
security-level 0
ip address X.X.138.132 255.255.255.0
ospf cost 10
interface GigabitEthernet1
description inside 10/16
nameif inside
security-level 100
ip address 10.1.1.254 255.255.0.0
ospf cost 10
access-list outside_access_in extended permit ip any any
access-list inside_nat0_outbound extended permit ip 10.1.0.0 255.255.0.0 10.20.0.0 255.255.0.0
access-list inside_nat0_outbound extended permit ip any 10.1.1.192 255.255.255.248
access-list outside_cryptomap_dyn_60 extended permit ip any 10.1.1.192 255.255.255.248
access-list outside_1_cryptomap extended permit ip 10.1.0.0 255.255.0.0 10.20.0.0 255.255.0.0
pager lines 24
ip local pool cnf-8-ip 10.1.1.192-10.1.1.199 mask 255.255.0.0
global (outside) 10 interface
global (outside) 15 1.2.4.5
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 15 10.1.0.0 255.255.0.0
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 X.X.138.1 1
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-MD5
crypto dynamic-map outside_dyn_map 20 set security-association lifetime seconds 28800
crypto dynamic-map outside_dyn_map 20 set security-association lifetime kilobytes 4608000
crypto dynamic-map outside_dyn_map 40 set transform-set ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA
crypto dynamic-map outside_dyn_map 40 set security-association lifetime seconds 28800
crypto dynamic-map outside_dyn_map 40 set security-association lifetime kilobytes 4608000
crypto dynamic-map outside_dyn_map 60 match address outside_cryptomap_dyn_60
crypto dynamic-map outside_dyn_map 60 set transform-set ESP-3DES-MD5 ESP-3DES-SHA ESP-DES-MD5 ESP-DES-SHA
crypto dynamic-map outside_dyn_map 60 set security-association lifetime seconds 28800
crypto dynamic-map outside_dyn_map 60 set security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set security-association lifetime seconds 28800
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set security-association lifetime kilobytes 4608000
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set peer X.X.21.29
crypto map outside_map 1 set transform-set ESP-DES-SHA
crypto map outside_map 1 set security-association lifetime seconds 28800
crypto map outside_map 1 set security-association lifetime kilobytes 4608000
crypto map outside_map 65534 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto isakmp identity hostname
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption des
hash sha
group 1
lifetime 86400
crypto isakmp policy 20
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp nat-traversal 3600
group-policy GroupPolicy1 internal
group-policy cnf-vpn-cls internal
group-policy cnf-vpn-cls attributes
wins-server value 10.1.1.7
dns-server value 10.1.1.7 10.1.1.205
vpn-tunnel-protocol IPSec l2tp-ipsec
default-domain value x.com
username sean password U/h5bFVjXlIDx8BtqPFrQw== nt-encrypted
tunnel-group DefaultRAGroup ipsec-attributes
pre-shared-key secret1
radius-sdi-xauth
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
tunnel-group cnf-vpn-cls type remote-access
tunnel-group cnf-vpn-cls general-attributes
address-pool cnf-8-ip
default-group-policy cnf-vpn-cls
tunnel-group cnf-vpn-cls ipsec-attributes
pre-shared-key secret2
isakmp ikev1-user-authentication none
tunnel-group cnf-vpn-cls ppp-attributes
authentication ms-chap-v2
tunnel-group X.X.21.29 type ipsec-l2l
tunnel-group X.X.21.29 ipsec-attributes
pre-shared-key SECRET
class-map inspection_default
match default-inspection-traffic
service-policy global_policy global
prompt hostname context
Cryptochecksum:9780edb09bc7debe147db1e7d52ec39c
: end
#2: Router 2811 config:
! Last configuration change at 09:15:32 PST Fri Oct 19 2012 by cnfla
! NVRAM config last updated at 13:45:03 PST Tue Oct 16 2012
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname LA-2800
crypto pki trustpoint TP-self-signed-1411740556
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1411740556
revocation-check none
rsakeypair TP-self-signed-1411740556
crypto pki certificate chain TP-self-signed-1411740556
certificate self-signed 01
3082023F 308201A8 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31343131 37343035 3536301E 170D3132 31303136 32303435
30335A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 34313137
34303535 3630819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100F75F F1BDAD9B DE9381FD 165B5188 7EAF9685 CF15A317 1B424825 9C66AA28
C990B2D3 D69A2F0F D745DB0E 2BB4995D 73415AC4 F01B2019 84373199 C4BCF9E0
E599B86C 17DBDCE6 47EBE0E3 8DBC90B2 9B4E217A 87F04BF7 A182501E 24381019
A61D2C05 5404DE88 DA2A1ADC A81B7F65 C318B697 7ED69DF1 2769E4C8 F3449B33
35AF0203 010001A3 67306530 0F060355 1D130101 FF040530 030101FF 30120603
551D1104 0B300982 074C412D 32383030 301F0603 551D2304 18301680 14B56EEB
88054CCA BB8CF8E8 F44BFE2C B77954E1 52301D06 03551D0E 04160414 B56EEB88
054CCABB 8CF8E8F4 4BFE2CB7 7954E152 300D0609 2A864886 F70D0101 04050003
81810056 58755C56 331294F8 BEC4FEBC 54879FF5 0FCC73D4 B964BA7A 07D20452
E7F40F42 8B355015 77156C9F AAA45F9F 59CDD27F 89FE7560 F08D953B FC19FD2D
310DA96E A5F3E83B 52D515F8 7B4C99CF 4CECC3F7 1A0D4909 BD08C373 50BB53CC
659C4246 2CB7B79F 43D94D96 586F9103 9B4659B6 5C8DDE4F 7CC5FC68 C4AD197A 4EC322
quit
crypto isakmp policy 1
authentication pre-share
crypto isakmp key SECRET address X.X.138.132 no-xauth
crypto ipsec transform-set la-2800-trans-set esp-des esp-sha-hmac
crypto map la-2800-ipsec-policy 1 ipsec-isakmp
description vpn ipsec policy
set peer X.X.138.132
set transform-set la-2800-trans-set
match address 101
interface FastEthernet0/0
description WAN Side
ip address X.X.216.29 255.255.255.248
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
no cdp enable
no mop enabled
crypto map la-2800-ipsec-policy
interface FastEthernet0/1
description LAN Side
ip address 10.20.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex full
speed auto
no mop enabled
ip nat inside source route-map nonat interface FastEthernet0/0 overload
access-list 10 permit X.X.138.132
access-list 99 permit 64.236.96.53
access-list 99 permit 98.82.1.202
access-list 101 remark vpn tunnerl acl
access-list 101 remark SDM_ACL Category=4
access-list 101 remark tunnel policy
access-list 101 permit ip 10.20.0.0 0.0.0.255 10.1.0.0 0.0.255.255
access-list 110 deny ip 10.20.0.0 0.0.0.255 10.1.0.0 0.0.255.255
access-list 110 permit ip 10.20.0.0 0.0.0.255 any
snmp-server community public RO
route-map nonat permit 10
match ip address 110
webvpn gateway gateway_1
ip address X.X.216.29 port 443
ssl trustpoint TP-self-signed-1411740556
inservice
webvpn install svc flash:/webvpn/svc.pkg
webvpn context gateway-1
title "b"
secondary-color white
title-color #CCCC66
text-color black
ssl authenticate verify all
policy group policy_1
functions svc-enabled
svc address-pool "WebVPN-Pool"
svc keep-client-installed
svc split include 10.20.0.0 255.255.0.0
default-group-policy policy_1
gateway gateway_1
inservice
end
#3: Test from Pix to router:
Active SA: 1
Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 1
1 IKE Peer: X.X.21.29
Type : user Role : initiator
Rekey : no State : MM_WAIT_MSG2
>>DEBUG:
Oct 22 12:07:14 pix535:Oct 22 12:20:28 EDT: %PIX-vpn-3-713902: IP = X.X.21.29, Removing peer from peer table failed, no match!
Oct 22 12:07:14 pix535 :Oct 22 12:20:28 EDT: %PIX-vpn-4-713903: IP = X.X.21.29, Error: Unable to remove PeerTblEntry
#4: test from router to pix:
LA-2800#sh crypto isakmp sa
IPv4 Crypto ISAKMP SA
dst src state conn-id slot status
X.X.138.132 X.X.216.29 MM_KEY_EXCH 1017 0 ACTIVE
>>debug
LA-2800#ping 10.1.1.7 source 10.20.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.7, timeout is 2 seconds:
Packet sent with a source address of 10.20.1.1
Oct 22 16:24:33.945: ISAKMP:(0): SA request profile is (NULL)
Oct 22 16:24:33.945: ISAKMP: Created a peer struct for X.X.138.132, peer port 500
Oct 22 16:24:33.945: ISAKMP: New peer created peer = 0x488B25C8 peer_handle = 0x80000013
Oct 22 16:24:33.945: ISAKMP: Locking peer struct 0x488B25C8, refcount 1 for isakmp_initiator
Oct 22 16:24:33.945: ISAKMP: local port 500, remote port 500
Oct 22 16:24:33.945: ISAKMP: set new node 0 to QM_IDLE
Oct 22 16:24:33.945: ISAKMP: Find a dup sa in the avl tree during calling isadb_insert sa = 487720A0
Oct 22 16:24:33.945: ISAKMP:(0):Can not start Aggressive mode, trying Main mode.
Oct 22 16:24:33.945: ISAKMP:(0):found peer pre-shared key matching 70.169.138.132
Oct 22 16:24:33.945: ISAKMP:(0): constructed NAT-T vendor-rfc3947 ID
Oct 22 16:24:33.945: ISAKMP:(0): constructed NAT-T vendor-07 ID
Oct 22 16:24:33.945: ISAKMP:(0): constructed NAT-T vendor-03 ID
Oct 22 16:24:33.945: ISAKMP:(0): constructed NAT-T vendor-02 ID
Oct 22 16:24:33.945: ISAKMP:(0):Input = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
Oct 22 16:24:33.945: ISAKMP:(0):Old State = IKE_READY New State = IKE_I_MM1
Oct 22 16:24:33.945: ISAKMP:(0): beginning Main Mode exchange
Oct 22 16:24:33.945: ISAKMP:(0): sending packet to X.X.138.132 my_port 500 peer_port 500 (I) MM_NO_STATE
Oct 22 16:24:33.945: ISAKMP:(0):Sending an IKE IPv4 Packet.
Oct 22 16:24:34.049: ISAKMP (0:0): received packet from X.X.138.132 dport 500 sport 500 Global (I) MM_NO_STATE
Oct 22 16:24:34.049: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
Oct 22 16:24:34.049: ISAKMP:(0):Old State = IKE_I_MM1 New State = IKE_I_MM2
Oct 22 16:24:34.049: ISAKMP:(0): processing SA payload. message ID = 0
Oct 22 16:24:34.049: ISAKMP:(0): processing vendor id payload
Oct 22 16:24:34.049: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch
Oct 22 16:24:34.049: ISAKMP:(0): vendor ID is NAT-T v2
Oct 22 16:24:34.049: ISAKMP:(0): processing vendor id payload
Oct 22 16:24:34.049: ISAKMP:(0): vendor ID seems Unity/DPD but major 194 mismatch
Oct 22 16:24:34.053: ISAKMP:(0):found peer pre-shared key matching 70.169.138.132
Oct 22 16:24:34.053: ISAKMP:(0): local preshared key found
Oct 22 16:24:34.053: ISAKMP : Scanning profiles for xauth ...
Oct 22 16:24:34.053: ISAKMP:(0):Checking ISAKMP transform 1 against priority 1 policy
Oct 22 16:24:34.053: ISAKMP: encryption DES-CBC
Oct 22 16:24:34.053: ISAKMP: hash SHA
Oct 22 16:24:34.053: ISAKMP: default group 1
Oct 22 16:24:34.053: ISAKMP: auth pre-share
Oct 22 16:24:34.053: ISAKMP: life type in seconds
Oct 22 16:24:34.053: ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
Oct 22 16:24:34.053: ISAKMP:(0):atts are acceptable. Next payload is 0
Oct 22 16:24:34.053: ISAKMP:(0):Acceptable atts:actual life: 0
Oct 22 16:24:34.053: ISAKMP:(0):Acceptable atts:life: 0
Oct 22 16:24:34.053: ISAKMP:(0):Fill atts in sa vpi_length:4
Oct 22 16:24:34.053: ISAKMP:(0):Fill atts in sa life_in_seconds:86400
Oct 22 16:24:34.053: ISAKMP:(0):Returning Actual lifetime: 86400
Oct 22 16:24:34.053: ISAKMP:(0)::Started lifetime timer: 86400.
Oct 22 16:24:34.053: ISAKMP:(0): processing vendor id payload
Oct 22 16:24:34.053: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch
Oct 22 16:24:34.053: ISAKMP:(0): vendor ID is NAT-T v2
Oct 22 16:24:34.053: ISAKMP:(0): processing vendor id payload
Oct 22 16:24:34.053: ISAKMP:(0): vendor ID seems Unity/DPD but major 194 mismatch
Oct 22 16:24:34.053: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
Oct 22 16:24:34.053: ISAKMP:(0):Old State = IKE_I_MM2 New State = IKE_I_MM2
Oct 22 16:24:34.057: ISAKMP:(0): sending packet to X.X.138.132 my_port 500 peer_port 500 (I) MM_SA_SETUP
Oct 22 16:24:34.057: ISAKMP:(0):Sending an IKE IPv4 Packet.
Oct 22 16:24:34.057: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
Oct 22 16:24:34.057: ISAKMP:(0):Old State = IKE_I_MM2 New State = IKE_I_MM3
Oct 22 16:24:34.181: ISAKMP (0:0): received packet from X.X.138.132 dport 500 sport 500 Global (I) MM_SA_SETUP
Oct 22 16:24:34.181: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
Oct 22 16:24:34.181: ISAKMP:(0):Old State = IKE_I_MM3 New State = IKE_I_MM4
Oct 22 16:24:34.181: ISAKMP:(0): processing KE payload. message ID = 0
Oct 22 16:24:34.217: ISAKMP:(0): processing NONCE payload. message ID = 0
Oct 22 16:24:34.217: ISAKMP:(0):found peer pre-shared key matching X.X.138.132
Oct 22 16:24:34.217: ISAKMP:(1018): processing vendor id payload
Oct 22 16:24:34.217: ISAKMP:(1018): vendor ID is Unity
Oct 22 16:24:34.217: ISAKMP:(1018): processing vendor id payload
Oct 22 16:24:34.217: ISAKMP:(1018): vendor ID seems Unity/DPD but major 55 mismatch
Oct 22 16:24:34.217: ISAKMP:(1018): vendor ID is XAUTH
Oct 22 16:24:34.217: ISAKMP:(1018): processing vendor id payload
Oct 22 16:24:34.217: ISAKMP:(1018): speaking to another IOS box!
Oct 22 16:24:34.221: ISAKMP:(1018): processing vendor id payload
Oct 22 16:24:34.221: ISAKMP:(1018):vendor ID seems Unity/DPD but hash mismatch
Oct 22 16:24:34.221: ISAKMP:received payload type 20
Oct 22 16:24:34.221: ISAKMP:received payload type 20
Oct 22 16:24:34.221: ISAKMP:(1018):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
Oct 22 16:24:34.221: ISAKMP:(1018):Old State = IKE_I_MM4 New State = IKE_I_MM4
Oct 22 16:24:34.221: ISAKMP:(1018):Send initial contact
Oct 22 16:24:34.221: ISAKMP:(1018):SA is doing pre-shared key authentication using id type ID_IPV4_ADDR
Oct 22 16:24:34.221: ISAKMP (0:1018): ID payload
next-payload : 8
type : 1
address : X.X.216.29
protocol : 17
port : 500
length : 12
Oct 22 16:24:34.221: ISAKMP:(1018):Total payload length: 12
Oct 22 16:24:34.221: ISAKMP:(1018): sending packet to X.X.138.132 my_port 500 peer_port 500 (I) MM_KEY_EXCH
Oct 22 16:24:34.221: ISAKMP:(1018):Sending an IKE IPv4 Packet.
Oct 22 16:24:34.225: ISAKMP:(1018):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
Oct 22 16:24:34.225: ISAKMP:(1018):Old State = IKE_I_MM4 New State = IKE_I_MM5
Oct 22 16:24:38.849: ISAKMP:(1017):purging node 198554740
Oct 22 16:24:38.849: ISAKMP:(1017):purging node 812380002
Oct 22 16:24:38.849: ISAKMP:(1017):purging node 773209335..
Success rate is 0 percent (0/5)
LA-2800#
Oct 22 16:24:44.221: ISAKMP:(1018): retransmitting phase 1 MM_KEY_EXCH...
Oct 22 16:24:44.221: ISAKMP (0:1018): incrementing error counter on sa, attempt 1 of 5: retransmit phase 1
Oct 22 16:24:44.221: ISAKMP:(1018): retransmitting phase 1 MM_KEY_EXCH
Oct 22 16:24:44.221: ISAKMP:(1018): sending packet to X.X.138.132 my_port 500 peer_port 500 (I) MM_KEY_EXCH
Oct 22 16:24:44.221: ISAKMP:(1018):Sending an IKE IPv4 Packet.
Oct 22 16:24:44.317: ISAKMP (0:1018): received packet from X.X.138.132 dport 500 sport 500 Global (I) MM_KEY_EXCH
Oct 22 16:24:44.317: ISAKMP:(1018): phase 1 packet is a duplicate of a previous packet.
Oct 22 16:24:44.321: ISAKMP:(1018): retransmission skipped for phase 1 (time since last transmission 96)
Oct 22 16:24:48.849: ISAKMP:(1017):purging SA., sa=469BAD60, delme=469BAD60
Oct 22 16:24:52.313: ISAKMP (0:1018): received packet from X.X.138.132 dport 500 sport 500 Global (I) MM_KEY_EXCH
Oct 22 16:24:52.313: ISAKMP:(1018): phase 1 packet is a duplicate of a previous packet.
Oct 22 16:24:52.313: ISAKMP:(1018): retransmitting due to retransmit phase 1
Oct 22 16:24:52.813: ISAKMP:(1018): retransmitting phase 1 MM_KEY_EXCH...
Oct 22 16:24:52.813: ISAKMP (0:1018): incrementing error counter on sa, attempt 2 of 5: retransmit phase 1
Oct 22 16:24:52.813: ISAKMP:(1018): retransmitting phase 1 MM_KEY_EXCH
Oct 22 16:24:52.813: ISAKMP:(1018): sending packet to X.X138.132 my_port 500 peer_port 500 (I) MM_KEY_EXCH
Oct 22 16:24:52.813: ISAKMP:(1018):Sending an IKE IPv4 Packet.
Oct 22 16:24:52.913: ISAKMP:(1018): phase 1 packet is a duplicate of a previous packet.
Oct 22 16:24:52.913: ISAKMP:(1018): retransmission skipped for phase 1 (time since last transmission 100)
Oct 22 16:25:00.905: ISAKMP (0:1018): received packet from X.X.138.132 dport 500 sport 500 Global (I) MM_KEY_EXCH
Oct 22 16:25:00.905: ISAKMP: set new node 422447177 to QM_IDLE
Oct 22 16:25:03.941: ISAKMP:(1018):SA is still budding. Attached new ipsec request to it. (local 1X.X.216.29, remote X.X.138.132)
Oct 22 16:25:03.941: ISAKMP: Error while processing SA request: Failed to initialize SA
Oct 22 16:25:03.941: ISAKMP: Error while processing KMI message 0, error 2.
Oct 22 16:25:12.814: ISAKMP:(1018): retransmitting phase 1 MM_KEY_EXCH...
Oct 22 16:25:12.814: ISAKMP (0:1018): incrementing error counter on sa, attempt 4 of 5: retransmit phase 1
Oct 22 16:25:12.814: ISAKMP:(1018): retransmitting phase 1 MM_KEY_EXCH
Oct 22 16:25:12.814: ISAKMP:(1018): sending packet to X.X.138.132 my_port 500 peer_port 500 (I) MM_KEY_EXCH
Oct 22 16:25:12.814: ISAKMP:(1018):Sending an IKE IPv4 Packet.
Oct 22 16:25:22.814: ISAKMP:(1018): retransmitting phase 1 MM_KEY_EXCH...
Oct 22 16:25:22.814: ISAKMP (0:1018): incrementing error counter on sa, attempt 5 of 5: retransmit phase 1
Oct 22 16:25:22.814: ISAKMP:(1018): retransmitting phase 1 MM_KEY_EXCH
Oct 22 16:25:22.814: ISAKMP:(1018): sending packet to X.X.138.132 my_port 500 peer_port 500 (I) MM_KEY_EXCH
Oct 22 16:25:22.814: ISAKMP:(1018):Sending an IKE IPv4 Packet.
Oct 22 16:25:32.814: ISAKMP:(1018): retransmitting phase 1 MM_KEY_EXCH...
Oct 22 16:25:32.814: ISAKMP:(1018):peer does not do paranoid keepalives.
Oct 22 16:25:32.814: ISAKMP:(1018):deleting SA reason "Death by retransmission P1" state (I) MM_KEY_EXCH (peer 70.169.138.132)
Oct 22 16:25:32.814: ISAKMP:(1018):deleting SA reason "Death by retransmission P1" state (I) MM_KEY_EXCH (peer 70.169.138.132)
Oct 22 16:25:32.814: ISAKMP: Unlocking peer struct 0x488B25C8 for isadb_mark_sa_deleted(), count 0
Oct 22 16:25:32.814: ISAKMP: Deleting peer node by peer_reap for X.X.138.132: 488B25C8
Oct 22 16:25:32.814: ISAKMP:(1018):deleting node 1112432180 error FALSE reason "IKE deleted"
Oct 22 16:25:32.814: ISAKMP:(1018):deleting node 422447177 error FALSE reason "IKE deleted"
Oct 22 16:25:32.814: ISAKMP:(1018):deleting node -278980615 error FALSE reason "IKE deleted"
Oct 22 16:25:32.814: ISAKMP:(1018):Input = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
Oct 22 16:25:32.814: ISAKMP:(1018):Old State = IKE_I_MM5 New State = IKE_DEST_SA
Oct 22 16:26:22.816: ISAKMP:(1018):purging node 1112432180
Oct 22 16:26:22.816: ISAKMP:(1018):purging node 422447177
Oct 22 16:26:22.816: ISAKMP:(1018):purging node -278980615
Oct 22 16:26:32.816: ISAKMP:(1018):purging SA., sa=487720A0, delme=487720A0
****** The PIX is also used VPN client access , such as Cicso VPN client 5.0, working fine ; Router is used as SSL VPN server, working too
I know there are lots of data here, hopefully these data may be useful for diagnosis purpose.
Any suggestions and advices are greatly appreciated.
SeanHi Sean,
Current configuration:
On the PIX:
crypto isakmp policy 5
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set peer X.X.21.29
crypto map outside_map 1 set transform-set ESP-DES-SHA
crypto map outside_map 1 set security-association lifetime seconds 28800
crypto map outside_map 1 set security-association lifetime kilobytes 4608000
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
access-list outside_1_cryptomap extended permit ip 10.1.0.0 255.255.0.0 10.20.0.0 255.255.0.0
tunnel-group X.X.21.29 type ipsec-l2l
tunnel-group X.X.21.29 ipsec-attributes
pre-shared-key SECRET
On the Router:
crypto isakmp policy 1
authentication pre-share
crypto map la-2800-ipsec-policy 1 ipsec-isakmp
description vpn ipsec policy
set peer X.X.138.132
set transform-set la-2800-trans-set
match address 101
access-list 101 permit ip 10.20.0.0 0.0.0.255 10.1.0.0 0.0.255.255
crypto ipsec transform-set la-2800-trans-set esp-des esp-sha-hmac
crypto isakmp key SECRET address X.X.138.132 no-xauth
Portu.
Please rate any helpful posts
Message was edited by: Javier Portuguez -
CSCtq10477 - Callmanager 9.1 can't make outbound calls, Route List gets error 41 - All devices busy
Hi all
I seem to have run into bug CSCtq10477 and maybe CSCul71689 and CSCum85086, where calls can be received from an MGCP gateway, but fail outbound with Callmanager logs showing
03095771.002 |17:34:14.103 |AppInfo |RouteListCdrc::null0_CcSetupReq - Terminating a call after the RouteListCdrc cannot find any more device.
03095771.003 |17:34:14.103 |AppInfo |RouteListCdrc::terminateCall - No more Routes in RouteListName = RL_OUTBOUND. Rejecting the call
03095771.004 |17:34:14.103 |AppInfo |RouteListCdrc::terminateCall - Sending CcRejInd, with the cause code (41), to RouteListControl because all devices are busy/stopped.
03095771.005 |17:34:14.103 |AppInfo |GenAlarm: AlarmName = RouteListExhausted, subFac = CALLMANAGERKeyParam = , severity = 4, AlarmMsg = RouteListName : RL_OUTBOUND, Reason=41, RouteGroups(RG_OUTBOUND)
and a Route List exhausted alarm appearing in RTMT.
Resetting the MGCP gateway in Callmanager, bouncing the serial interface, E1 controller and No MGCP/MGCP has no impact. I could also see the circuit was not full.
We have got round this by removing the gateway from the Route Group and pointing the Route Patterns directly at the gateway and this works. I can see two of the bugs above are fixed in the latest 9.1.2SU3 code (9.1.2.13900-10), but I don't see CSCtq10477. This bug document shows some 9.1 code is OK, but not this one.
9.1(1.21020.1) - Not listed for download, is this an ES?
9.1(2.10000.11) - Not listed for download, is this an ES?
9.1(2.10000.28) - 9.1(2) - but not shown in the release notes for 9.1(2) either.
Does anyone know if the Release notes just missed this out, or does the bug document need the Fixed versions to be updated?
ThanksHi,
9.1(1.21020.1) is an ES.
9.1(2.10000.28) is the base version of 9.1(2) so this bug will be fixed in this version or any higher version of 9.1(2).
Upgrading to the latest ES or 9.1(1) or 9.1(2)SU3 would take care of this bug.
HTH
Manish -
Neeed tocreate new route list in omgk t-code
hi
I need to create a new route list which should be assigned in the omgk t-code
in t-code omgk
we have scope list when we click on it, another screen opens where we have
list scope scrren and sub screen attached to it
when we slect any one and click on line structure, another screen opens qwhere we have to assign the create route list
problem to solve is :
as sap has standard oute list where they are linked to some fileds to display.
we need to create a route list and have to link to some fileds and it is assigned to scope list
when we run t-code me5a and select scope list which we have created, output it should show only these filed.
THis is bit urgentUse MM06E005 enhancement to add fields in screen of ME21N
SAPMM06E 0101 CUSTSCR1 SAPLXM06 0101 Subscreen: PO header
SAPMM06E 0111 CUSTSCR1 SAPLXM06 0111 Subscreen: PO item
SAPMM06E 0201 CUSTSCR1 SAPLXM06 0201 Subscreen: agreement header
SAPMM06E 0211 CUSTSCR1 SAPLXM06 0211 Subscreen: agreement item
SAPMM06E 0301 CUSTSCR1 SAPLXM06 0301 Subscreen: RFQ header
SAPMM06E 0311 CUSTSCR1 SAPLXM06 0311 Subscreen: RFQ item
Use the appropriate screen exit depending on where u require to add field -
Recently I replaced my wireless router with a new NetGear RangeMax from a dLink. The dlink was having DHCP issues. Everything appears to be working fine with the exception of one thing. Port forwarding. It is setup and definitely working for some Windows boxes on the network as it operates VNC for example fine. However my iMac which is using Apache to serve some web pages seems to be acting oddly. Typing in localhost in the browser on the Mac connects instantly. I use no-ip to carry a domain name and using that the browser is connecting to the correct IP and the browser actually shows the title of the website and lists 2 of 3 items have loaded but then times out and the link fails. Do I need to tweak the .conf file of Apache fro some weird reason related to router change. The routers port forward is pointing to the correct ip for the Mac (i printed out the old forwarding data from the dlink and I am using TCP and not TCP/UDP. This is really odd to me - is it possible the NetGear is causing some weirdness in finishing the response to port forward.
Regards,
GuyCharlie,
I seem to have figured it out - it wasn't Apache and I really did suspect that it could not have been given the router swap was the only change. Here is the thing the NetGear does not support a particular variation of NAT, which kills things like MobileMe from working correctly. In the end switching to a more modern DLink cured the whole thing. Its all working fine now. As nice as the Netgear is in the set up tool, it does not have all the detailed bells and whistles needed to make everything work smoothly. It went up for sale on craigslist already.
Thanks -
Linux on my X220T (and why it failed)
I’m sorry but this is going to be a long post but I have seen so many posts out there from people in my position - making an attempt to migrate from Windows to Linux - that I felt compelled to share my experiences. This is not a Linux bashing post either. Like UFOs, I want to believe. I just haven’t seen the light yet so if there are any Linux evangelists out there who have got Linux working on their X220T then I would *love* to hear from you
Background and reasons for change:
I am not your ordinary Windows user. I work in IT and I’ve been working with Windows since the days of v2 (yes I’m that old) running on Dos. I’m comfortable with it. Because of my age I’m also comfortable with the command line. I’ve worked with Xenix (a variant of the original Unix) and have a grasp of the fundamentals. Now I’m all grown up and an IT consultant I wanted to ‘round out’ my understanding of my business by getting to grips with Linux in order to write code. I understand it’s very different to the nice little bubble of Visual Studio where everything happens around you. I’ve yet to find out Sure I can produce a virtual machine and learn in there but wanted to immerse myself in it all so decided to convert my X220T. This little beauty is not my main work computer so I could sacrifice the contents. If your X220T is your only machine and you need it for serious stuff, think carefully before going ahead.
Starting point:
My X220T was pretty much out-of-the-box Windows 7. It was working fine, but had the odd glitch. Wouldn’t hibernate properly (although it did before an ‘upgrade’ screwed it up) and the mouse kept losing its settings despite following all the advice, upgrading, hacking etc to fix it. I also had Windows 8 preview on the ‘Q’ drive and was liking that but of course it’s not really ready to go yet.
My choice was Linux Mint with the KDE desktop. Did a bit of digging. Seemed to do the job. So I took several backups, trashed the drive and installed it.
My previous experiences with Linux have always been a battle to get the OS to see certain devices. Wireless cards never used to work. Peripherals failing. Not resuming from hibernate. That kind of thing. This time it was flawless. It simply installed. Everything appeared to work! Fantastic!! Of course it wasn’t all there yet. But because my internet access was up and running (had always been an issue before) I was a happy man.
Then three things happened almost simultaneously.
I wanted to read an eBook and the screen wouldn’t rotate
I couldn’t log on using my fingerprint reader
My fan wouldn’t shut up
So thought I would tackle the first issue. KDE supports a tool that pops a nice little icon on to your task bar to allow screen rotation. Didn’t work. What it did do was install the Wacom drivers to manage the touch screen and it would re-orientate the mouse ‘as if’ the screen had rotated, but the display itself was in portrait mode. So spent two evenings after work working out how to make this happen. In the end I wrote two shell scripts to rotate the screen AND to set the Wacom drivers to orientate the mouse and stylus properly. Job done! Felt pleased with myself. I was cross that the KDE interface screen button thingy didn’t work properly but that’s life. I had learned something. Two dos-like icons on my task bar flipped my screen (albeit slowly) from landscape to portrait and back again.
Meanwhile, I’m sitting in my conservatory (no power) and watching my battery disappear in about two hours. Under windows, my usage pattern gave me at least five hours before a re-charge. And that pesky fan didn’t run once! Peace!! But not with Linux. It was annoying so thought I would tackle that next. Everyone uses their machine differently so since power consumption is quite subjective I thought if I fixed this I could move on to other things and then ‘suddenly notice’ that my battery is still powering my baby after four or five hours.
After research and digging into a cpu frequency daemon (background process) I realised that this was the wrong line of attack. That took another two evenings of work. The Linux Mint kernel doesn’t support this. More research suggested that this was an old/different methodology and the approach was to use cpu ‘governers’ to control cpu frequency switching. The governers have names like ‘ondemand’ and ‘conservative’ and as you might guess, the conservative one holds the processor speed down to reduce power consumption. You may assume dear reader that I had done all the other stuff. Turning off bluetooth only happened in software and I gave up before researching that. It may be possible to turn it off in hardware via the operating system but didn’t get that far. Screen brightness, wireless etc. Typically when I read a book I flick the hardware radio-off switch on the side which of course turns off bluetooth and wireless, so they were taken out of the equation in terms of power consumption.
After another evening of digging I managed to discover how to instruct the machine to use the ‘conservative’ governor. By now I’m starting to get a bit fed up. My philosophy was partly to learn what it was like to live in the world of Linux, but mostly to get to grips with the C++ compilers, possibly mono (A windows-like development environment) and Apache (system for hosting web sites) but hadn’t got beyond the foibles of the operating system. Finally got the conservative governor in place, rotated my screen (still working!) and settled down to a good read (purely for testing purposes of course
Within five minutes, on the came the pesky fan. Battery gone in about three hours. This had me seriously pissed off by now. But still wanted to battle on. Thought I would tackle the fingerprint reader next. Found a driver but it didn’t work. I could register a fingerprint but when it came to save the results it died. Even as the godlike super user it failed.
Then I found another gui based app and that one worked. Well, it worked nicely in-system. Anything that needed elevated privileges it would work for. I just couldn’t use it to log in. When the laptop was in tablet mode I couldn’t authenticate with my fingerprint reader and there was no on-screen keyboard to use as an alternative.
And it was all these little things that eventually drove me screaming back towards Windows. I’m now running Windows 8 CP as my main desktop. It’s incomplete and has its own set of foibles, but by installing some of the drivers that Lenovo supply for Windows 7 it is perfectly usable.
The screen rotates out of the box
The buttons along the bottom of the screen work to rotate the screen (never did get that working in Linux but it was on my list
Power consumption is back to being pretty good for a laptop rather than just average
I can turn my bluetooth off at the hardware level but leave my wireless running so that I can browse the internet without hammering my battery too much (using the Lenovo on-screen utility form Windows7)
I can logon with my fingerprint reader and when it fails (I get it wrong three times) I can revert to an on-screen keyboard to get me out of trouble without having to switch to desktop mode to do it.
I know they are small things but they are now what I am used to and what I expect from my operating system so why should I do without them?
My feeling as I sit here writing is that Linux is great. Don’t get me wrong here. I still love it and intend to explore further, but unlike Windows there is a learning curve that you HAVE to climb. You have no choice. When I come home at the end of the day, sure I want to play with my little Lenovo and have some fun. But then I want to relax. Do a bit of surfing, read my ebooks and generally do stuff that the operating system is intended to support. Instead the operating system got in the way of my user experience rather than supporting my user experience. The problem for me is that wihlst I can produce a Linux machine in vmWare or VirtualBox, the driver woes I’ve just described are hidden from you because those virtual worlds either abstract the problem away or don’t port-over the hardware from the host that you want to explore the problems with. The only solution is to buy another X220T to play with and that’s not worth it for me.
I also think that my relatively large understanding of Windows frustrates my experience of because I am now a novice with the computer which I’m definitely not used to and that of course skews my perception.
So if there are any Linux superheroes out there who have solved all the above issues and can lead me into the glorious sunshine of developing in the wonderful world of Linux then please talk to me. And for the rest of you guys in my position for whom this has struck a chord, if you want to play, I’m sure the results are worth it but prepare to be frustrated!!Hi all. I must be in league with the devil as my lucky number is 13. When I saw Galloping Gerbil or Raring Rhinocerous or whatever the **bleep** thing is called I also saw v13.04 and thought that the time had come to go again!
So it's about a year on now. Two important things have happened. The first is that my trusty old X220T is now no longer my primary machine so I can afford to lose it to experimentation for a while. The second is that the huge behemoth that is Linux is rolling over the bugs and niggles that sent me screaming back to Windows all those months ago.
So I've tried again with Raring Ringtail v13.04 and right now I feel as if I've come home! It's still not right but it's pretty close! More importantly, I fee that I'm no longer in the minority in wanting to get this to work right. There is this big push out there towards touch screen so people are spending time on this and wanting their software to be touch screen friendly so it is!
Before I go on, I was rather shocked when I did my pre-13.040-install research to find this post top of the google list on linux on x220! I'm guessing that my thoughts must parallel a lot of other people thinking about making the jump. So to that end, here's some thinking.
13.04 is close. Really close to being a very serious competitor to Windows. My view is that Linux is about there now. The X220T is a complex beast to support. it has touch, pen, fingerprint readers, rotating screens etc. And it all works pretty well. I can do a sudo apt-get install to make the fingerprint reader work. And it DOES work. Reliably. I still have issues rotating the screen but I've learned enough now to knock up a simple bash script that will do it for me. AND (this is where the Linux philosophy works) I have written the script to suit me. I like to hold the battery unit in my left hand and hold my laptop in portrait mode to read books/browse the internet. Then switch to normal orientation to type emails etc. The script only toggles between normal and anti-clockwise and back again. Works for me.
The issue with Linux was more that it was a philosophy than an operating system. You don't just "use" it. You immerse yourself in it. That made it geeky and non mainstream. You can make it sit up and do stuff that suited you exactly if you were prepared to put the time in. The issue was that until now it didn't do the basics reliably enough to suit everyone. I used to read a lot of stories about sons/friends putting Linux on to Mums/Dads/Grans laptop and it working beautifully. Linux is very very good at this. It just works. But getting it there was a right pain unless you were lucky. Now however that out-of-the-box functionality is really really close. To the point at which Tracey from Essex (forgive me Tracey!) can stick the CD in and expect the same functionality from Linux that she could get from Windows without having to sweet talk that geeky bloke that she knows has a crush on her to come in and sort it all out
Once you get past that bit then you end up in this little wonderful world. Without too much effort courtesy of all those hard-working ordinary people out there, I have a machine that will do most of what I want without tweaks and pokes that take days to research. Now I can browse, read my books, play the odd game and "ignore" the operating system until such times as I choose to tackle the odd tweak. On my relatively small screen for example I want hide the Unity launch bar thingy. However if I do this I can't get it back via the touch interface. Enter Ginn! I have yet to play with tihs but I can configure multi-touch gestures to "do stuff" like making the launcher appear with two finger gestures (!) and that little nugget of configuration pleasure is waiting in the wings for when I get bored reading the news or playing silly games. My operating system has now become a toy, a tool and a learning centre. I can now pursue my long term dream (okay I have modest dreams!) of being able to develop AJAX based web sites using WCF in Mono running under Apache. That means I have all the fun of learning how to use Apache, and working out how to make WCF code in Mono. These things are easy for me under Windows and IIS but how you do it in Linux is a new and exciting challenge! Yes I truly am that boring!
I wish I could change the title of my original post because Linux is coming of age. Windows had better watch out. -
LO 26603 (missing parameter and db logon failed)
Hi Experts,
I am getting a known error discussed on the forum many times,this is my first stint with CR_LO-Xcelsius,getting stuck at the Error LO 26603.
The dashboard is having a tab sets (3 CR in each tab) and out of three, I am getting u201CParameter Value Missing for oneu201D and u201CDatabase Login Failed for two tabsu201D.
I have already referred the following threads but none of them is answered..
error LO 26603 crystal reports - live office - xcelsius
Error Code: LO 26603
Xcelsius missing parameter values (LO 26603)
Database logon failed (LO 26603)
The Task:
Get CR into the embedded excel using Live Office. To show charts.
The Problem:
Once i preview the Dashboard, data is displayed for the default date.
The CR Server login is popped upon refresh request (triggers from the dashboard) and providing the correct info (Admin user name and pwd) also the error is thrown Lo 26603.
The parameters (3 in no.) are common for all the three reports: (All setting done from Prompt settings)
1. Date u2013 Data in the charts refreshes when the date is changed (I/P from Calendar in Xcelsius). Cell Binding (Option from Choose Excel Data Range)
2. Region u2013 Selected (All) from prompt setting in LO Excel (Choose Value List).
3. Products u2013 Selected (All) from prompt setting in LO Excel (Choose Value List).
I have set the DB logon information for processing the report in CMC and not sure of using SSO to bypass the DB logon prompt.
Please help, how I can troubleshoot this problem.
Config.
Crystal Server XI 3.1 SP2
Xcelsius 2008 5.3.3.0
SAP Integration Kit SP2
Live Office XI 3.1 SP2
Rgds
SamGo to CMC
Go to your CR
Right-click and select database configuration
Hardcode logon credentials
This should solve your issue.
Regards,
Rohan -
Bill and Routing Interface concurrent program is not processing component
Hi All,
While running Bill and Routing Interface concurrent program,not processing the component item(Line Item) from bom_inventory_comps_interface,still it show process flag as 1. where as billing item(Header Item) is successfully done..i have tried with all the option by giving component sequence id and batch id still it is not processing component item..
Is it recommendable to give bill sequence id and component sequence id in interface table using bom_inventory_component_s sequence..
I will be very pleased if i listen from u guys... Plz help me in resolving this issue..
My Header Insert Stmt..
INSERT INTO apps.bom_bill_of_mtls_interface@system_link_visma
(assembly_item_id, organization_id,
alternate_bom_designator, last_update_date,
last_updated_by, creation_date, created_by,
revision, item_number, item_description,
implementation_date, transaction_type,
process_flag, assembly_type, batch_id
VALUES (l_inv_item_id, l_org_id,
NULL, SYSDATE,
1318, SYSDATE, 1318,
l_revision, l_item_num, l_description,
SYSDATE, 'CREATE',
1, 1, 10003535
Component Insert stmt
INSERT INTO apps.bom_inventory_comps_interface@system_link_visma
(operation_seq_num, component_item_id,
item_num, basis_type, component_quantity,
auto_request_material, effectivity_date,
disable_date, planning_factor,
component_yield_factor,
enforce_int_requirements,
include_in_cost_rollup, wip_supply_type,
supply_subinventory, supply_locator_id,
check_atp, optional,
mutually_exclusive_options,
low_quantity, high_quantity,
so_basis, shipping_allowed,
include_on_ship_docs, required_to_ship,
required_for_revenue, component_remarks,
transaction_type, process_flag,
assembly_item_id, component_item_number,
batch_id,component_sequence_id
VALUES (l_operation_seq, l_comp_item_id,
cur2.item_sequence, l_basis, cur2.quantity,
l_auto_request_mtls, cur2.from_date,
cur2.TO_DATE, cur2.planning_factor,
cur2.yield_factor,
l_enforce_int_requirements,
l_include_in_cost_rollup, l_supply_type,
l_supply_subinventory, NULL,
l_check_atp, l_optional,
l_mutually_exclusive_options,
cur2.minimum_quantity, cur2.maximum_quantity,
l_sale_order_basis, l_shippable_flag,
l_include_on_ship_docs, l_required_to_ship,
l_required_for_revenue, cur2.comments,
'CREATE', 1,
l_inv_item_id, l_comp_item_num,
10003535,apps.bom_inventory_components_s.nextval@system_link_visma
For Subcomponent Insert Stmt
INSERT INTO apps.bom_sub_comps_interface@system_link_visma
(substitute_component_id,
substitute_item_quantity,
assembly_item_id, component_item_id,
operation_seq_num, organization_id,
substitute_comp_number,
component_item_number,
assembly_item_number,
transaction_type, process_flag,
enforce_int_requirements,
effectivity_date,component_sequence_id,batch_id
VALUES (l_sub_comp_item_id,
cur3.quantity,
l_inv_item_id, l_comp_item_id,
cur2.operation_sequence, l_org_id,
l_sub_comp_item_num,
l_comp_item_num,
l_item_num,
'CREATE', 1,
l_enforce_int_requirements,
SYSDATE,apps.bom_inventory_components_s.currval@system_link_visma,10003535
Thanks
Raman Sharma
Edited by: 929841 on May 4, 2012 12:28 AM
Edited by: 929841 on May 4, 2012 2:58 AMYou need to populate the organization_id or organization_code in bom_inventory_comps_interface.
Here is a minimal insert
INSERT INTO bom.bom_inventory_comps_interface
(operation_seq_num, last_update_date, last_updated_by,
creation_date, created_by, process_flag, transaction_type,
bom_item_type,
effectivity_date, organization_code, assembly_item_number,
item_num, component_item_number, component_quantity
VALUES (1 -- op_seq_num
,SYSDATE, 1433
,SYSDATE, 1433, 1 -- process_flag
,'Create',
4 -- bom_item_type 1 Model; 2 Option class; 3 Planning; 4 Standard; 5 Product family
,SYSDATE - 1, 'PUB', 'SSGPARENT1' -- assembly_item_number
,10 --item_num
, 'SSGCOMP1' -- component_item_number
, 10 --qty
)Sandeep Gandhi
Maybe you are looking for
-
Issue with reinstalling a brand new mac pro
I was recomended to reinstall the leopard since I had some issues with my new 27" cinema display.( there is an update for the cinema display and my mac did not allow me to updat it so apple care person told me to reinstall the leopard. After 15 minut
-
Rentals not showing up for ipad
i rented two tv shows to watch on a plane on my ipad. when i plug my ipad in, they don't show up. they DO show up when i plug my iphone in, but i wanted to watch on the ipad. any thoughts? thx.
-
Possible to change the variables in the program permanently?
Is it possible to change the content of the variable in the MIDlet application??
-
How can I reduce the font size of the display when browsing my yahoo mails from my BB
-
Please I want to make a snapshot from a driverless usb webcam in Labview 2011. I can do that easily using Matlab. Any help.