10.4 Install disk won't see new hard drive

My 10.5.6 drive is dying so I replaced it with a brand new drive. I bought my computer just after the 10.5.0 upgrade, so it came with two 10.4 disks and a 10.5 upgrade disk.
When I insert 10.4 disk 1 and boot, I get to the point where I am asked to select a drive. Nothing is showing. My hard drive is not recognized.
There is only one setup path. There is no way to use Utility or any other program. There are no tabs, options or anything else but this setup path. OsX 10.4 Disk 2 is not recognized. The OSX 10.5 disk is not recognized.
Any suggestions are greatly appreciated.

1. Insert the Mac OS X Install disc that came with your computer, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the Erase tab.
4. Click the disclosure triangle to the left of the hard drive icon to display the names of your hard disk volumes and partitions.
5. Select your Mac OS X volume.
6. Highlight the drive, select Partition Tab, then Format type... MacOS Extended Journalled... after completion hopefully you'll be able to install.

Similar Messages

Follow up to HD crash - Install disk can't see new Hard Drive !!!

I may have a bigger problem on my hands.
I rebooted with my original install disk of OS X and when it gets to the "choose location" window, it does not see the new hard drive......????
I'm thinking about re-checking connections and/or possibly pull the hard drive out and do an external connection just to verify that it spins.
Not sure how to proceed and/or what to check ?? Suggestions ???

Make sure you chose the right format, and as far as partitioning in concerned, you have to select at least one partition, which will be the entire drive.

Install Disc won't see main hard drive

I'm trying to upgrade from 10.4.11 to 10.5. When I'm booted up from the install disc, my main hard drive doesn't show up as an option to install onto. My secondary internal hard drive shows up, as well as my firewire drive. What's the deal? Thanks-Karen

Try going into Disk Utility and see if you disk pops up. If not restart your mac and hold the "c" key. If that does not work go to the Apple Store.

Need to re-install CS5.5 on my new hard drive. Serial number from disk package not working.

I need to re-install CS5.5 on my new hard drive. Serial number from disk package not working.

if there's a problem with the number of installations, you'll see a message about an excess activation problem.
if that's what you're seeing, contact adobe support for an activation count reset, https://helpx.adobe.com/contact.html
otherwise, attach a screenshot of the error message or quote it.

Installing OS X on a NEW hard drive

I just installed a new hard drive on the macbook pro. however, when i run the installation disk it never actually installes os x instead it trys to install the applications, but cant find the drive. How do I install OS X on a new hard drive? Thanks.

Hello,
The first thing you need to do is partition and format the drive.
From the OS X installation screen, go up to the menus at the top, and locate Disk Utility.
Launch Disk Utility.
Now, select your hard drive on the left.
Then, click on the Partitions Tab.
Now, choose the single partition option (unless you want to divide the drive for some reason). Then, give it a name.
Choose the format "Mac OS X Extended (Journaled).
Now, click on the button to partition the drive.
When it's done, exit Disk Utility.
Now, proceed with the installation. If it still won't see the hard drive, then re-start from the installation disk again and try it again. It should see the hard drive now and permit you to install on it.
I hope this helps.
Let us know if you have other questions.
P.S., if you'd like, go ahead and click the "Helpful" or "Solved" buttons on any of the posts / replies above if you feel they were helpful or adequately answered your question.

How can I re-install CS2 upgrade on a new hard drive without serial no. of previous Photoshop 5?

A new hard drive has been installed on my G4 Mac with OS10.4. I am trying to re-install CS2 Premium on the new hard drive but I no longer have the serial number of my previous Photoshop 5. I need to enter this as the CS2 was an upgrade. I have spoken to Adobe technical support but they no longer support CS2 so are not able to help. They recommended that I try the Adbe Forum. All my Adobe products have been bought legitimately. I know people manage to use pirated Adobe software so there must be some way for me to activate a legally bought product.

Michael
Thank you for your email and suggestion.
I have tried that and the only product listed is my CS5 Design Premium (which was an upgrade), none of my previous Adobe products are listed.
I am now looking to see if I can buy an old version of Photoshop that will work on a Power PC G4 Mac with OS 10.4.
I only need Photoshop on that Mac to paint from, not the rest of the Suite.
It is infuriating that I already have a legitimately bought Adobe product (as all mine have been) but I am unable to use it.
Regards
Trevor

How to install Windows XP on a new hard drive in desktop computer

Have a Lenovo desktop. I replaced the defective hard drive. Obtained Windows XP installation disks from Lenovo. I received recovery two
Recovery CDs, namely Rescue and Recovery CD and Product Recovery CD along with 5 CD Roms ( 1of 5 through 5of 5).
I want to install Windows XP in my new Hitachi hard drive. Should I use only the 5 CD ROMS 1 thru 5, leaving out the Recovery and Rescue CD
and Product Recovery CD Rom.
How to I install Window XP in my new hard drive? I am not a computer
wizard. As a retired IBM senior citizen I need some help from the community. I am not cognizant with the steps to follow. I am a new
member of this great community.
Thanks a bunch ! padman
personal informations removed for your own security

padman215, welcome to the forum,
you need to boot from the Rescue and Recovery cd and select to recover the system and then to recover to factory state. It will then eventually ask for the other discs.
Please be sure that you read the messages carefully; if it asks for a supplementary disc, (which you don't seem to have), you need to click on "no" should it ask for one - this throws alot of people.
Happy installing
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

Trouble installing 10.4 on a new hard drive

My hard drive died, so I'm trying to install 10.4 on a new hard drive. I'm using the same disk that came with my laptop. I get as far as "select a destination" and the hard drive doesn't show up to choose. I saw another post that suggested partitioning the hard drive first, so I did that, and still no luck. Can anyone help?

Thanks for the welcome, and for the attempt to help. I'm starting to wonder if I got a bum replacement hard drive? I've just restarted twice, it now takes FOREVER for the apple and the little spinny thing to show up when I start up and hold down the C key, and now when I go to disk utility the hard drive doesn't show up in the list of choices at all. Do you think it's worth pulling out the hard drive and sticking it back in again? I have no idea if that will make any difference?

I'm having to re-install PSE 11 on a new hard Drive. I clicked the installer and it ran, but says it's missing the .exe file. I then downloaded PSE 11 from your website and when I unzipped it and ran it, it wanted to uninstall PSE 11. Now I'm contactin

I'm having to re-install PSE 11 on a new hard Drive. I clicked the installer and it ran, but says it's missing the .exe file. I then downloaded PSE 11 from your website and when I unzipped it and ran it, it wanted to uninstall PSE 11. Now I'm contacting you

Okay, so, fast forward from July to now -
- I've visited my closest Apple store's genius bar twice now. (Over an hour and a half away.)
- My computer spent at least 8 hours behind their closed doors in the workshop
- Several complete erases of the harddrive have taken place
- Most of the Apple geniuses I dealt with were nice and very knowledgeable, but they were and still aren't 100% sure exactly what is wrong with my computer.
The good news is:
- They were able to at least get it running again, with a clean install from their servers of OS X Lion 10.7.5
- They believe that my problems stem from either 1 of 2 things:
- Faulty Hard Drive (even though it is brand new)
- The wrong build of software being installed.
Now, while the wrong build does seem like it could be the problem, it doesn't make sense in the aspect that all of the initial problems began when the first hard drive failed. The same problems continued when I changed out the failed hard drive with the brand spanking new one, and only slightly improved when I was able to successfully install the OS that came with the original disks for my computer. I'm not convinced this thing is back to normal, but hopefully I can make it last through getting a shiny new retina Macbook Pro in the coming future. Thank you so much to everyone who read and replied to this post!
- Andrew =)

HT1727 i copied itune music from old hard drive to memory disk the copied onto new hard drive into itunes and music wont play unless removalbe disk is inserted

i copied itune music from old hard drive to memory disk the copied onto new hard drive into itunes and music wont play unless removalbe disk is inserted

Then your iTunes must be looking at the removable disc, not your hard drive. Did you actually copy the songs onto your computer, or simply tell iTunes to look at the removable drive?
Highlight a song and click on File/Get Info/Summary>Where and check the location that iTunes has listed for the song. What does it say?

Need Help Installing an OS on a new Hard Drive

H, I just installed a new Hard Drive on my G4. My problem is I cannot find the original G4 install discs.
I do have OSX Panther discs which I bought later. Can I use these to install a new OS?
How would I do this as the new Hard Drive is brand new and probably not formatted? Do I power up the mac and load the Panther install disc 1 or is this not the correct procedure?
Also I have an external LaCie CD drive because the one in the mac doesn't work. Will the external LaCie CD drive be recognized when I put the OSX Panther discs in it to install an OS on my new Hard Drive?
Sorry for so many questions but I don't want to mess this up.
Thanks

Thanks for replying Thomas. Well my G4 Hard Drive was shot so I took it out and installed a new one so I have to reinstall everything (new OS & all applications). I tried to use Super Duper to Clone the HD but the HD was too far gone, so now I need to install an OS on the new Hard Drive.
I can't find my original G4 install cd's. I do have Panther OS discs and an iLife disc I bought awhile back. Can I use these instead of the original G4 install disc?
Here's the process to install a new OS as I understand it. Please correct me if I am wrong or am missing a step.
1) Put the first Panther install disc in the cd tray.
2) Power up the G4 while holding down the "C" key
3) Follow the installation instructions
Thanks!

Disk Utility won't recognize new hard drive

Hello,
Thanks for taking the time to read this.
The original hard drive (80 GB) went bad, so I replaced with a new 160 GB Western Digital one. I formatted the hard drive using Disk Utility from the Mac OS X Disk. It worked the first time I booted into Leopard (I just booted up to make sure the OS loaded...didn't install any new software and/or hardware).
Then I shut it down and started it back up, and the computer didn't recognize the hard drive. I inserted the Mac OS X disk and ran Disk Utility, but the hard drive was not recognized.
So now I'm thinking the new hard drive was also bad. So, I ordered another one (Seagate 160 GB) and it to was not recognized when I ran Disk Utility from the Mac OS X disk.
When replacing all of them, I followed directions I found here and other websites. They all said to do it the same way, so I'm assuming the directions for replacing a hard drive in a laptop were correct.
I searched Google and found several posts suggesting using an application called Disk Warrior, but from my understanding, you cannot run it from a disk, it needs to be installed, which is obviously impossible since the hard drive isn't recognized.
Then I ran Open Firmware and did "devalias" from the prompt. From what I can tell in the list of hardware, the hard drive is recognized, but I am not sure. I took a picture of the screen printout but do not see an option to attached it to this post. Therefore, I'll just tell what it said for now and will create an image hosting account so I can add a URL for it later.
In the list, "hd" is in the left column and in the right column of the same line is "/pci@f4000000/ata-6@d/disk@0" (without quotes).
If anybody has any suggestions, they would be greatly appreciated.

Welcome to the Apple discussions.
I've replaced a few hard drives, and in instances where it's not recognized, it's either been a cable connection issue or I've seen others with a jumper issue. Either the hard drive to logic board cable isn't properly set, typically on the logic board side, or a jumper was left on the drive, where typically you can just remove it. I haven't personally had the cable fail, however, that's possible too.
When you pulled the large plug from the back of the original hard drive, did you do it very carefully? It's not like a desktop hard drive plug that you can just pull out ... it needs to be wiggled out, gently. I have a hard time believing two new drives would be essentially DOA, although the first one worked for a bit, which leads me to wonder about the physical connections.
Since you have your original OS X disks, you could try running the Apple hardware test to see if it gives you any error message(s).

Cannot Install OS 8.1 on new hard drive, 233 G3 Powerbook

Ok, so here's the deal.
I have an old Powerbook G3 Wallstreet. 233 Mhz 13" screen.
I recently ran into a problem where I booted up, and the hard drive (original 2GB) was erased. Completely reinstalled, and as soon as it rebooted after the install, the hard drive was empty again. Weird.
So, I decide to reinstall OS8 on a new hard drive. I have an older 20 GB drive from a compaq Armada M700, which I had replaced with a newer 120 GB drive, so I used that in the Powerbook.
Anyway, I've tried lots of things. Fully empty nonpartitioned drive, single 8GB partition by using MacDisk in windows, multiple 8GB partions, what have you. Disk Setup does not see any hard drive I place in the powerbook. I tried both the 120 and the 20 GB.
Any suggestions? I only have a Windows machine to work with, as the G3 is my only Mac. (Well, I have a graphite iMac, but it's suffering from the screen shrinking/power down problem common to those units, so I can't really do anything with it.)

ShatteredOne,
When you have installed the OS and restarted, did you get the blinking '?' alternating with a folder? If so, try resetting the PRAM to possibly correct this issue.
http://docs.info.apple.com/article.html?artnum=2238
Will the Wallstreet boot to the MacOS 8.1 CD? If so, try Drive Setup on the 8.1 CD again after resetting the PRAM.
The original Wallstreet shipped with a special OS 8.1 CD (green label) since the retail MacOS 8.1 CD will not have the necessary Powerbook G3 enabler file.
You do not have to partition the HD, but just make sure you are have formatted as HFS Extended although HFS Standard will work. However, on a large drive like the 120GB, you will have a lot of wasted space due to the block size.
If still having problems, install the original 2GB HD > boot to the 8.1 CD > open the utilities folder on the CD > Drive Setup and select 'zero all data' when you initialize; now run the Test Disk test and see if it passes. If it fails, zero/test one more time.

I need help re-installing my OS on a new hard drive. Having MAJOR issues with this simple task.

I have a MacBook Pro 15" (mid 2009) I recently needed to get a new hard drive for it, the old one stopped working. It came with OS X Snow Leopard already installed from Apple, and it also came with the install disks. I have booted up using the install disks and put OS X Snow Leopard back on the computer.
I tried booting with a USB install disk of OS X Lion (10.7) but had no luck on multiple occasions. It would only get through the initial step of the install and then say it couldn't download additional components needed for OS X
So finally, I decided to try a full erase and reformat of my brand new hard drive (less than a week old) and stated with the basic software that came with the computer. Installing that worked fine, until I tried to do a software update through the built in program. My computer refused to download 10.6.8 from the apple servers, so I had to find it on a 3rd party website. Once I found it and downloaded it, I finally got it installed. There were 12 more updates after I did 10.6.8 and none of them worked when I tried downloading and installing as a group. I had to do each one individually, the last one being a security update.
Up to this point, the Mac App Store didn't work (even after the 10.6.8 update), I couldn't download any of my previous purchases. I needed to download lion, to see if having it on the Mac hard drive itself would help with the install, but I couldn't do that until after the security update.
Other than that, the Mac worked normally except for during each start up, the apple logo would flash along with the forbidden sign and the folder with a question mark on it. It flashed for a few seconds randomly, then would boot up normally or say that my computer would need to be restarted.i figured this issue would be fixed after I successfully installed lion.
FINALLY I got the App Store to download lion, and began the install process. Halfway through the install, it failed and when I tried to restart the computer, it continuously flashes through those three symbols at startup. I can't get it to do anything else. I'm so ****** off I'm ready to just sell it for parts.
My questions are:
      1. Can I install OS X Lion OR OS X Mountain Lion clean from the start after a full format of the hard drive?
      2. How do I go about installing clean and get my computer to stop flashing those symbols during start up?
*I have performed the Apple Hardware extended test and all systems are reporting normal function*

Okay, so, fast forward from July to now -
- I've visited my closest Apple store's genius bar twice now. (Over an hour and a half away.)
- My computer spent at least 8 hours behind their closed doors in the workshop
- Several complete erases of the harddrive have taken place
- Most of the Apple geniuses I dealt with were nice and very knowledgeable, but they were and still aren't 100% sure exactly what is wrong with my computer.
The good news is:
- They were able to at least get it running again, with a clean install from their servers of OS X Lion 10.7.5
- They believe that my problems stem from either 1 of 2 things:
        - Faulty Hard Drive (even though it is brand new)
         - The wrong build of software being installed.
Now, while the wrong build does seem like it could be the problem, it doesn't make sense in the aspect that all of the initial problems began when the first hard drive failed. The same problems continued when I changed out the failed hard drive with the brand spanking new one, and only slightly improved when I was able to successfully install the OS that came with the original disks for my computer. I'm not convinced this thing is back to normal, but hopefully I can make it last through getting a shiny new retina Macbook Pro in the coming future. Thank you so much to everyone who read and replied to this post!
- Andrew =)

Cant install mountain lion on a new hard drive 2011 mac pro 17"

for some reason I bought the infamous 2011 mac pro, and the hard drive kept having IN/OUT problems and after it destroyed half day of work, I decided to get a new hard drive, *blue WD 500g" but i have tried EVERYTHING and i just cant install mountain lion on it.
1.- i tried forcing the recovery mode so It would connect to the internet and download mountain lion but after 10 min or so i trows the -2002f error at me
2.- I tried to use the old hard drive that i put on a external hard drive reader so I could get the recovery partition but i just keep restarting the installation no reason given
3.- downloaded the mountain lion and tried to installing it on the system hard drive of the laptop trough a computer running snow leopard but dosn't let me.
4.- tried the same thing on target mode without success
5.- using the recovery partition I used disk utility to se of the partition was locked but it was not
6.- created a different partition to see if it would install it there didn't work.
i just don't understand why
any toughs?
if you answer this you would be a personal hero of mine
cheers

Make Your Own Mavericks, Mountain/Lion Installer
After downloading the installer you must first save the Install Mac OS X application. After the installer downloads DO NOT click on the Install button. Go to your Applications folder and make a copy of the installer. Move the copy into your Downloads folder. Now you can click on the Install button. You must do this because the installer deletes itself automatically when it finishes installing.
   2. Get a USB flash drive that is at least 8 GBs. Prep this flash drive as follows:
Open Disk Utility in your Utilities folder.
After DU loads select your flash drive (this is the entry with the mfgr.'s ID and size) from the leftside list. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID then click on the OK button. Click on the Partition button and wait until the process has completed.
Select the volume you just created (this is the sub-entry under the drive entry) from the left side list.
Click on the Erase tab in the DU main window.
Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
Click on the Erase button. The format process can take up to an hour depending upon the flash drive size.
Use DiskMaker X to put your installer clone onto the USB flash drive.
Make your own Mavericks flash drive installer using the Mavericks tool:
You can also create a Mavericks flash drive installer via the Terminal. Mavericks has its own built-in installer maker you use via the Terminal:
You will need a freshly partitioned and formatted USB flash drive with at least 8GBs. Leave the name of the flash drive at the system default, "Untitled." Do not change this name. Open the Terminal in the Utilities folder. Copy this entire command line after the prompt in the Terminal's window:
     sudo /Applications/Install\ OS\ X\ Mavericks.app/Contents/Resources/createinstallmedia --volume
     /Volumes/Untitled --applicationpath /Applications/Install\ OS\ X\ Mavericks.app --nointeraction
Press RETURN. Enter your admin password when prompted. It will not be echoed to the screen so be careful to enter it correctly. Press RETURN, again.
Wait for the process to complete which will take quite some time.

10.4 Install disk won't see new hard drive

Similar Messages

Maybe you are looking for