10.5.6 upgrade - gant get past the password screen

Hi, hope someone can help.
I installed the upgrade, it appeared to go well. However, when I switch my iMac on I get the password screen as normal. I then type my password in, the screen goes blue, and cycles back to the password screen after a couple of seconds.
I cant access my iMac at all, its a blinking nightmare!
Any help would be appreciated.

I have had this happen before. Try a restart and see if that fixes it. It did for me. If not try starting up in Single user mode and run FSCK.
When booting, hold your Command-S key down. When you get to the command line, type the following: fsck -fy and hit Return. When it's done verifying/repairing, type reboot

Similar Messages

I cannot get past the password screen

I cannot get past the password screen, I've tried resetting it but it tells. Me I'm not an allowed user

If the old Macbook(?) has Snow Leopard 10.6 installed, and you have that retail install disc or the system disc of the current (base level) system on it, you could use the installer disc as a boot volume and use the utilities on the booted install disc to reset the password. It should be a menu option in the booted Install disc, way short of any effort to re-install anything. And if your computer can do this, the same DVD has Disk Utility, to check/repair the Mac HDD.
What OS X version do you have, & what MacBook, etc is that?
Good luck & happy computing!

I cannot get past the password screen on my old laptop - I'm entering the password I always used and it is not working

I am trying to log on to an old laptop and I cannot get past the password screen - I'm using the password I always used and it is not working. Even the clue doesn't help. Is there anything I can do. The last time it was turned on the apple staff transferred data to my new laptop. Help

If the old Macbook(?) has Snow Leopard 10.6 installed, and you have that retail install disc or the system disc of the current (base level) system on it, you could use the installer disc as a boot volume and use the utilities on the booted install disc to reset the password. It should be a menu option in the booted Install disc, way short of any effort to re-install anything. And if your computer can do this, the same DVD has Disk Utility, to check/repair the Mac HDD.
What OS X version do you have, & what MacBook, etc is that?
Good luck & happy computing!

My sister has changed a setting on her ipod that makes it speak. I got past the password screen once but could not scroll to accessibility. Now i cannot get past the password screen. I have tried resetting and restoring but neither is working.

How do i turn the voice off??
A little padlock with a circle around it has also appeared next to the battery symbol

Connect the iPod to its syncing computer and then go to he Summary pane for the iPod in iTunes. Click on Configure Universal Access and turn Voice Over Off.
The padlock is that the screen rotation lock is one. To turn off, doble clcik the HOme button and go all the way to the left on the Dock row past the music controls and tap on the padlock in the circle arrow.

Can't get past the Blue Screen during startup

I decided to upgrade the 4/8/08 firmware on my aluminum bluetooth keyboard this afternoon using my mac mini. Shortly after the procedure started, something happened to the keyboard and it could not complete the install. I tried a second time, but again no luck. I then decided to replace the keyboard batteries and try again, but I was no longer able to connect the keyboard to the mini.
I decided to restart the computer and try the whole procedure again. But after the grey screen comes up with the Apple logo, the mini went to the blue screen with the spinning gear, then the mouse appeared in the upper left hand corner, then a little later the gear, then nothing, then the mouse, then the gear... I could never get past this blue screen.
I plugged in a wired keyboard and was able to startup 10.5 using the install DVD, which allowed me to check and repair the permissions and the disk. After a restart, still stuck on the blue screen.
I tried zapping the pram. Still couldn't get past the blue screen.
I was not able to start up in safe mode (is the timing critical for when to hold down the shift key?)
I started up in single user mode and attempted to move the preference files as described here:
http://docs.info.apple.com/article.html?artnum=106464#symp1
but got an error that I did not have the correct permissions. I assume that is because I was trying to save the preference1.old (and preference2.old, etc) files to the root part of my hard drive.
Any suggestions? Does it make sense that upgrading the firmware on a bluetooth keyboard could take down the whole computer???

Disconnect all peripherals from your computer.
Boot from your install disc & run Repair Disk from the utility menu. To use the Install Mac OS X disc, insert the disc, and restart your computer while holding down the C key as it starts up.
Select your language.
Once on the desktop, select Utility in the menu bar.
Select Disk Utility.
Select the disk or volume in the list of disks and volumes, and then click First Aid.
Click Repair Disk.
Restart your computer when done.
Repair permissions after you reach the desktop-http://support.apple.com/kb/HT2963 and restart your computer.

How can I get past the white screen?

When I start my iMac I see a message that my start up disk is full and that I need to delete files. After I type in my user name and password, all I see if a white screen. This problem started today. The error message about the start up disk started two days ago, and when I looked at the disk, I saw that over half of it has files described as "other". The hard drive is 250 GB. I have Time Machine backups but I don't know how to get to them to help me. So, I guess that I have two questions: how do I get past the white screen, and what are the files that are catogoraized as other? Thanks.

I did not put the OS info in my question because I am not sure what I have. I upgraded to Lion so that I could use the cloud between my devices, however I do not know the number.
Apple menu item->About this Mac and the version is listed there. Click on that and get the build number. Click again and get the machine's serial number.
I am stuck on the white screen. Any other advice?
Start with a google search for white screen mac. This one might do the trick: http://www.mac-forums.com/forums/apple-desktops/138137-imac-wont-get-passed-whit e-screen.html

My MacBook Air can't get past the gray screen with the apple logo. What's the fix?

My MacBook Air can't get past the gray screen with the Apple logo, so I can't login. Does anyone know the fix for this?

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into Recovery by holding down the key combination command-R at the startup chime, or from a local Time Machine backup volume (option key at startup.) Release the keys when you see a gray screen with a spinning dial. When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in the support article linked below, under “Instructions for backing up to an external hard disk via Disk Utility.”
How to back up and restore your files
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode by holding down the key combination command-T at the startup chime. Connect the two Macs with a FireWire or Thunderbolt cable. The internal drive of the machine running in target mode will mount as an external drive on the other machine. Copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
How to use and troubleshoot FireWire target disk mode
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Before reconnecting an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode.* The instructions provided by Apple are as follows:
Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
When you see the gray Apple logo, release the shift key.
If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
*Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Post for further instructions.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
If you can boot and log in now, reboot as usual (i.e., not in safe mode.) If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see above for instructions.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it produces. Look for the line "Permissions repaired successfully" at the end of the output. Then reboot as usual.
Step 6
Boot into Recovery again. When the OS X Utilities screen appears, follow the prompts to reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with proxy servers, or with networks that require a certificate for authentication.
Step 7
Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a backup.
Step 8
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested.

My new iMac had the old data transferred in-store but now it won't accept the password on the first screen. How can I reset this? I can't get past the first screen as a result.

I cannot get past the initial screen on my new iMac. Data was transferred from my old computer so when I turned it on It automatically had my name in the window and asked for the password, but none of my old passwords seem to be accepted. How can I fix this?? It's a new IMac with osx.

Which password isn't working? The one to access the iPad or the one to get your hotmail?
If hot mail, you go into the settings, mail, contacts and calendars and edit your hot mail account. Of if it won't edit, delete it off the iPad, then re-add it with the new password.

I have a MacBook Pro, it recently started freezing upon startup. It would get to a blue screen and just sit there. I've tried booting in safemode to run disk repair and still doesnt help. If I do manage to get past the blue screen, it still freezes

My mac keeps freezing upon startup. It will get to the blue screen and promptly freeze. If I manage to get past the blue screen, and open up youtube on google chrome, it will freeze before it loads youtube. I've tried safeboot and disk repair, nothing seems to work. I even tried to factory reset it but it wont connect to my internet when I reboot with power + option.. any ideas?

This can be used to boot the machine and delelte enough files to get it to boot normally.
.Create a data recovery/undelete external boot drive
Read about storage drive so you can store your extra stuff.
Most commonly used backup methods
Also here to see how a full boot drive slows the machine down
Why is my computer slow?

My macbook pro wont get past the grey screen at startup. Help!!

After doing a run of the mill software update on my macbook pro (running snow leopard) it froze during the "moving items into place" stage. I forced a shut down and now it wont get past the grey screen with apple logo and spinning wheel. I have tried booting from the original DVD but it still freezes. When I boot it in verbose mode it seems to stop at "jnl: unknown-dev: update_fs_block: error reading fs block # 3597880! (ret 5)", the Apple AHCD Disk Queue manager :: set power state is timing out and there is a disk I/O error. I have tried to reset the power manager (not sure if it worked or not) and I have also tried clearing the PRAM (again, not sure of that worked). When I try to look at the hard drive using target mode on my imac the hard drive doesn't come up but the DVD does. I'm concerned that my hard drive is fried. Any suggestions?

It would help to state in your post which remedies you tried that didn't work.
Start here > OS X Lion: If you see a gray screen at startup
If nothing there helped, try Starting up in Safe Mode
Safe Mode deletes some system caches that may help.
A Safe Mode boot takes longer than a normal boot so be patient. Once you are in Safe Mode, click Restart from the Apple menu.
If a Safe Mode boot didn't work, since your Mac has OS X v10.7 installed, restart your Mac while holding down the Command + R keys so you can access OS X Recovery built in utilities. The startup disk may need repairing.
Tip: Hold down the Eject key while starting up your Mac to eject a disc.

Ipad screen is white. Restored it on iTunes. Press home and on switch goes black then back to white with no logo at all. Can't get past the white screen. This happened after running app updates. 16GB OS 7.1.1

The ipad screen is white. Holding buttons didn't work so I restored it on iTunes. When I press home and on switch, the screen is white, goes black then back to white with no logo at all. Can't get past the white screen. This happened after running app updates. Is there any fix besides going to Apple store? In iTunes on computer can see what is on there. 16GB OS 7.1.1

FORCE IPAD INTO RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port.
DO NOT RELEASE BUTTON until you see picture of iTunes and plug
5. Release Home button.
ON COMPUTER
6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
7. Select "Restore iPad"...
Note:
1. Data will be lost if you do not have backup
2. You must follow step 1 to step 4 VERY CLOSELY.
3. Repeat the process if necessary.

IMac G5 running OS 10.4.11. Started playing with a bluetooth speaker (may or may not be related). Now I cannot get past the blue screen on startup. I can get into safe mode. Tried install disc for disc utility and reloaded OS. Still get blue screen.

I have an older iMac G5 running OS 10.4.11. The other day I started playing with a bluetooth speaker (may or may not be related). Now I cannot get past the blue screen on startup.
I can get into safe mode. But no regular startup.
I tried disabling bluetooth, thinking that might be related. It didn't help.
I even tried using the install disc to run disc utility. That didn't work so I reloaded the OS.
But I still get hung on the blue screen when trying a normal startup.
All help would be appreciated.

Try resetting the PMU/SMU and PRAM/NVRAM. You'd need to identify the mode of resetting depending on the model of your G5 iMac. The Apple support sites that would help you for this are –
http://support.apple.com/kb/HT1436
http://support.apple.com/kb/HT1939
http://support.apple.com/kb/HT1767
http://support.apple.com/kb/HT1379
I hope this solves your problem.

HT2173 my iMac will not get past the start screen, after i restarted it after it not being able to upload my photos from my iPhone 4S to iPhoto app on my iMac bc a visa vas about 3:15 min

my iMac will not get past the start screen, after i restarted it after it not being able to upload my photos from my iPhone 4S to iPhoto app on my iMac bc a visa vas about 3:15 min. What should I do to get my imac past this?

According to your posted Profile here you are running a PPC based iMac. This Forum is only for "Intel iMac's", and so to get the expert and correct help you need you should repost your question in the "PPC iMac Forum".
Hope this helps

My macbook pro will not get past the gray screen with the apple logo and a loading bar.

My macbook pro will not get past the grey screen with the apple logo after attempting to load for hours. I have already tried resetting the NVRAM/PRAM and a couple other tricks and no luck. Anyone out there have suggestions for my problem? Help would be much appreciated since i use my computer for everything at school and i am in desperate need to get this baby working again.

You didn't say which OS in your tag, but maybe you might find something here.
http://support.apple.com/kb/TS2570
http://support.apple.com/kb/PH4191
http://support.apple.com/kb/PH7213
http://support.apple.com/kb/HT4125
http://support.apple.com/kb/HT2213

HT4718 I cannot get past the restore screen

So, big problem. I have had to replace my logic board. Following this, using Mountain Lion, my mac was unusable, just beach ball on every click. I did restore Mountain Lion, but no change. I cannot restore from time machine as I get an error message saying restart. Now, I cannot get past the restore screen, no matter what keys are held at startup. If I hold the option key at startup, I get the recovery disk and back up showing, neither of which can be used.
In short, I'm stuck, any help appreciated!

If you successfully restored the iPod to factory settings/new iPod (went through all the steps without errors), then time for an appointment a the Genius Bar of an Apple store.

10.5.6 upgrade - gant get past the password screen

Similar Messages

Maybe you are looking for