10.5.7 update results in major problem with external drives

yesterday I did the 10.5.7 update and now I can't access any of my external hard drives. The message is "you do not have proper privileges". Have tried downloading/installing the combo update, running permissions repair with Disk Utility, even tried reinstalling my original 10.5.2 system with 'Archive and Install', still the problem persists.
In the privileges dialog, the setting is 'custom' and I can't switch anything back to "read/write".
I'm sure there are other problems but this is quite major as all my work files are located in external drives.
help!

Is it only Lacie drives you've had trouble with, or is it other brands as well?
This is probably a separate problem, but when I updated to OS X 10.5.7, my Buffalo hard drives disappeared. See these threads:
External Hard Drives not recognized now by 10.5.7
http://discussions.apple.com/thread.jspa?threadID=2010075&tstart=0
Don't install 10.5.7
http://discussions.apple.com/thread.jspa?threadID=2004304&tstart=60&start=15
Buffalo has since released a patch:
http://forums.buffalotech.com/buffalo/board/message?board.id=0101&thread.id=9986

Similar Messages

Problem with external drive (OS X 10.9.4)

after i upgrade the OS,my iMac can't eject my external hard drive
and the "Tuxera" was gone from system preference...
it comes like this when i try to verify the disk..
===== Saturday, July 12, 2014 at 3:16:30 AM Western Indonesia Time =====
2014-07-12 03:16:33 +0700: Verifying volume “disk1s1”
2014-07-12 03:16:33 +0700: Starting verification tool:
2014-07-12 03:16:33 +0700: Checking file system
2014-07-12 03:16:33 +0700: ** /dev/disk1s1
2014-07-12 03:16:33 +0700: Invalid BS_jmpBoot in boot block: 000000
2014-07-12 03:16:33 +0700: Error: This disk needs to be repaired. Click Repair Disk.
2014-07-12 03:16:33 +0700:
2014-07-12 03:16:33 +0700: Disk Utility stopped verifying “disk1s1”: This disk needs to be repaired. Click Repair Disk.
2014-07-12 03:16:33 +0700:
and then i clicked repair disk and this one comes...
2014-07-12 03:16:33 +0700:
2014-07-12 03:18:28 +0700: Verify and Repair volume “disk1s1”
2014-07-12 03:18:28 +0700: Starting repair tool:
2014-07-12 03:18:28 +0700: Checking file system
2014-07-12 03:18:31 +0700: ** /dev/disk1s1
2014-07-12 03:18:31 +0700: Invalid BS_jmpBoot in boot block: 000000
2014-07-12 03:18:31 +0700: Volume repair complete.
2014-07-12 03:18:31 +0700: Updating boot support partitions for the volume as required.
2014-07-12 03:18:31 +0700: Error: Disk Utility can’t repair this disk. Back up as many of your files as possible, reformat the disk, and restore your backed-up files.
2014-07-12 03:18:31 +0700:
2014-07-12 03:18:31 +0700: Disk Utility stopped repairing “disk1s1”: Disk Utility can’t repair this disk. Back up as many of your files as possible, reformat the disk, and restore your backed-up files.
2014-07-12 03:18:31 +0700:
anyone please help me,i don't understand about programming..
and i/m sorry for my bad English..
thanks you guys

Disk Utility can’t repair this disk. Back up as many of your files as possible, reformat the disk, and restore your backed-up files.
You need to copy all the data off the drive then erase and reformat. If you do not have enough room on your internal drive you would need to buy an external drive to copy the data. If the drive cannot be repaired, then you would have to buy a new drive as a replacement.
If your data saved on the drive does not exist anywhere else, it's always good to have a backup of the drive in cases like this where the drive need repair.

Formatting Problems with External Drive

Hello. I recently switched from a Dell to a Mac, and I love it. The problem is, the motherboard fried on my old Dell. The files on my hard disk are fine, but I can't use migration assistant since the PC won't turn on. My tech support guy put the files from my old Hard drive onto my external hard drive which was formatted for PC use. When I plugged it into my Macbook, Time Machine came up and reformatted the drive, erasing all the files. We gave my stuff back to the Tech support guy, and when he tried to plug the drive into his PC, it was in Mac OS X format, so he couldn't put files on it. Can I possibly change the format of this drive to Fat 32 (whatever that means) on my Mac? Thanks.

Use the Disk Utility in the /Applications/Utilities/ folder to reformat the drive to MS-DOS.
(30283)

10.9.3 = major problem with fast user switching

I've found a major problem with the 10.9.3 update with my 27" iMac, you probably won't see it if your on a laptop. I did all the updates in past few days i.e., 10.9.3 combo update, iTunes 11.2.1.
Afterward I noticed a bug when Fast User Switching i.e. FUS. I have 5 accounts but the bug can be replicated with only 2.
I login to userA have some windows open but you can just open a Finder window. Now make the window at least half the with of the screen and move it to the right side of the screen. Then login in to userB and setup the windows the same way as userA. Now FUS to userA and then back to userB. You will notice that the Finder window has been moved to the upper left corner of the screen. This problem happened's to all user accounts you login to except the first account you logged into.
Since I didn't know what update caused the problem I had to use Time Machine to revert to my last version of 10.9.2. I then double checked the for the bug and sure enough everything was working fine. I now was going to install one update at a time and to see which one was causing the bug. So I installed 10.9.3 first and found the bug immediately.
I now know what's happening. When the switch occurs the screen is resized to about the equivalent of a 13" MBP. At this point the windows that fall some ware outside that size get moved to the upper left corner and resized. Then the screen resizes to normal but it's too late, all the window have moved and been resized to fit the 13" screen size.
You can reproduce this effect by going to System Preferences and selecting Display and then select the Scaled radio button. No select the smallest size, say, 1280 x 720. Now select the Best for display radio button again. You will now see all the windows you have open that were too big no moved and resized to the upper left corner. I know why the Mac moves the windows, it's so you don't have any windows stuck off screen.
Now when I say 13" it could be some other size but it's about that size give or take.

Yes, it's when you user Fast User Switching.
Here's snapshot before the screen resized. Ignore the window in the lower right, I moved it from the upper left before taking the screen shot.
I hate to say it but I'm glad I'm not the only one with this bug.

Major problems with Premiere CS4

Hello there!
I'm having major problems with CS4. I recently bought a new computer - essentials are as follows:
Intel Core i7 920 2.66GHz
2 x Kingston 3x2GB, DDR3 1333MHz (=12 GB RAM)
Ati Radeon HD 5770 v2
Asus P6T SE, LGA1366, X58, DDR3, ATX
2 x 500GB, Barracuda 7200.12 (RAID1), system disk
2 x 1TB Barracuda 7200.12, media disks
Windows 7 Pro 64 bit
Adobe CS4 Production Premium + latest updates
The problem I have has mostly to do with Premiere although I think the rest of Production Premium softwares should be running better on this computer as well.
For starters, I was highly disappointed when I couldn't view a single HD clip from the Premiere timeline (it was an .m2ts rip from a previously self-burned Bluray disc) at all. Rendering is very slow and even after that the video doesn't run normally, showing just a few individual frames per second. When I point the timeline at a certain spot, it takes many seconds until even that very frame is shown in the monitor window.
And this is not all - I decided to try with a basic DV AVI clip, previously captured with my PPro 1.5 on my earlier computer (3.2ghz Pentium from 2005). It's a native file so it doesn't even need rendering and still the same problem occurs. With normal playback only about 6-10 frames are shown per second. It's absolutely ridiculous - even my 2004 laptop runs DV AVIs more smoothly with PPro 1.5.
While I'm running the Premiere, the level of used RAM comes only up to around 24 percents. The processor, then again, comes close to a hundred when play is pressed on the timeline.
I haven't had such immense problems with other Production Premium softwares (though as I said, I think they should be running faster as well). Otherwise the computer is running smoothly.
A friend of mine pointed out that the graphics card I'm using isn't on the Adobe website's list of supported ones with Premiere, but afaik it shouldn't even be a graphics card problem with this high-end machinery.
So - I sure could use some help and ideas about how to get the Premiere working. My main intention for buying a new computer and Adobe CS4 Production Premium was to start HD editing after all! Thanks beforehand!

Hi
Yeah, I hope he solves problem and knows how it got solved and tells us all...it's like being a detective ! " Mr Plum did it in the "svchost" room ! "
I got a little lost on this....
You are welcome and I'm glad that it paid off so nicely for you. One more suggestion, if I may: I'm a big fan of a fixed pagefile size. When making a fresh install of Windows, one of my first actions is to set a fixed pagefile on a different disk (min=max) before installing anything else on that different disk and removing the pagefile on the C drive. This will ensure that the pagefile in on the fastest part of the drive and will never be fragmented.
I think it used to be that I made swapfiles, or swapdisks which now seems to be called pagefile. That in itself is a little confusing semantic wise, because of the use of mempage stuff. It used to be that base memory was 640k, with the upper memory (to make up 1024 kb) was mostly for drivers and stuff. If more memory was needed than 640k (an event the inventor never thought possible... "who could want more than the enormous amount of 640K ?", he said..)..the extended and expanded memory got invented to swap memory pages from that 640k as needed with the rest of RAM. That's basically correct right ? Sooooo, I don't know if that still goes on, but I suspect it does, unless someone totally changes the architecture of the computer and cpu and fsb and everything... but I don't know what is going on nowadays. Anyway, there were other ways besides windows OS to create virtual memory on the hard drive, and Photoshop was one of the programs that could do that, I think.
Why MS would want to call the swapdisk virtual memory "pagefile" is beyond me.
Anyway, be that as it may, I understand that making the pagefile first on a drive so it's close to the center of the drive (heads don't have to travel far to access). But I haven't added a lot of drives to a system before, and I suspect I will be pretty soon...and this is the part I don't get...
You add drives and put OS on them? So they are bootable ? I've added a drive or two but just formatted and used as more storage but didn't put OS on them. So that part is confusing...
Then you take the pagefile off the C: drive ? Are you then using the new drive as your boot drive and the C: drive is too full to use accept to run the programs already installed ?
Thanks again !
Rod

Strange major problem with 975X PowerUp Intel MOBO

I’m suddenly having a strange major problem with a MSI 975X Platinum PowerUP Edition V2.1 MS-7246 Intel socket 775 motherboard. Previously, it had given me no problems at all.
It went like this:
Powered on system in the morning, booting from a cold start.
Hit DEL key to get into the BIOS.
Missed the window and the system booted into Windows normally.
Re-started the system from within Windows.
Hit DEL key to get into the BIOS and was successful the second time.
Hit the ENTER key on the first item “Standard CMOS Features”.
The DATE, TIME and other information was displayed on the next screen, but at this point, the BIOS screen became completely unresponsive to any keyboard input.
The only thing I could do at that point was to power off.
Subsequent power on boot-ups resulted in the system always freezing at the BIOS splash screen after the video card sign-on.
I have switched power supplies, hard drives, keyboards and video cards. I have disconnected everything except the video card, keyboard and one RAM module. I have switched the four RAM modules around and then reduced the RAM to one 256MB module in the proper slot. I even changed the battery on the MOBO, in case it had shorted out and removed and re-seated the BIOS chip. It still halts at the BIOS splash screen.
The BIOS chip can’t be completely dead, because I powered off and pushed the BIOS reset button on the MOBO to reset the BIOS to the factory defaults. When I re-booted, I could tell that it had actually reset to the factory defaults because I had previously set the BIOS to reboot the system on resumption of power and the factory default was to remain off until the power button was pushed, which was now the default.
I’m stumped! All I can think of is to get a new pre-programmed BIOS chip and see if that makes any difference, but I’m not sure this system is even worth the expense with no guarantee of success. Any suggestions on how I might get past the BIOS splash screen or do I for sure have a corrupt BIOS chip?

System specs as per the posting guidelines -
Board: MSI 975X Platinum PowerUP Edition V2.1 MS-7246 Intel socket 775
Bios: Version (can’t recall & can’t check since it won’t go past the BIOS splash screen)
VGA: ASUS EN7600GS nVidia GeForce 7600GS PCI-e 256MB DDR2 (also tried new XFX nVidia
Geforce 210 PCI-e 2.0 512MB DDR3)
PSU: Chiefmax 680W ATX (also tried new OCZ 700W ATX)
CPU: Intel 2.8GHz LGA-775 Core2 Duo Dual-Core Processor
MEM: 4 x Samsung 512MB 1Rx8 PC2-5300U (2GB total)
HDD: Seagate Barracuda 250GB SATA2 (also tried Seagate Barracuda 500GB SATA2)
COOLER: Intel OEM LGA 775 fan/heatsink C25897-001
OC: No
OS: Vista Home Premium 32-bit
I have been through the BIOS reset procedure several times and pretty much as outlined. As I said before, I could tell that it had taken a reset to the factory defaults, because the power on option had changed.

I am experiencing some major problems with my MacBook Pro. I have had some issues with it turning on/off at random times, but today, when starting, I get the grey start-up screen and a recovery bar. After filling in approx 1/4 of the way, the machine dies

I am experiencing some major problems with my MacBook Pro. I have had some issues with it turning on/off at random times, but today, when starting, I get the grey start-up screen and a recovery bar. After filling in approx 1/4 of the way, the machine dies. After starting it in recovery mode, it will not allow me to download OS X Mavericks- it says the disk is locked. Any ideas? I do not have a back-up and do not want to erase everything before I have explored my options. Help?

try forcing internet recover, hold 3 keys - command, option, r - you should see a spinning globe
most people will tell you to do both pram and smc resets (google) and if you still have issues, either clean install (easy) or troubleshoot (hard)

I am having major problems with my trackpad on my macbook pro. I can no longer press down on the bottom left and right corners for it to click and follow my command. Please can anyone help?

I am having major problems with my track pad on my macbook pro. Even though my settings haven't changed...my trackpad is no longer responding as it did before. The left hand corner no longer clicks when I press it and my personal commands which I set up in preferences no longer seem to be workin. Please help!

Some websites have an internal mute or volume setting. If that's not the issue, see below.
From the Safari menu bar, select
          Safari ▹ Preferences... ▹ Privacy ▹ Remove All Website Data...
and confirm. Close the window. Then select
           ▹ System Preferences… ▹ Flash Player ▹ Advanced ▹ Delete All...
In the sheet that opens, check the box marked
          Delete All Site Data and Settings
then click Delete Data. Close the preference pane.

Hi, I have a macbook air os x 10.9.5 and I have problems with the app store. It doesn't open anyway. so, how can I install it again or update. I have problems with preview too, the same, doesn't open the application

Hi, I have a macbook air os x 10.9.5 and I have problems with the app store. It doesn't open anyway. so, how can I install it again or update. I have problems with preview too, the same, doesn't open the application

Reinstalling OS X Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Reinstalling OS X Without Erasing the Drive
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility and press the Continue button. After Disk Utility loads select the Macintosh HD entry from the the left side list. Click on the First Aid tab, then click on the Repair Disk button. If Disk Utility reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit Disk Utility and return to the main menu.
Reinstall OS X: Select Reinstall OS X and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
Alternatively, see:
Reinstall OS X Without Erasing the Drive
Choose the version you have installed now:
OS X Yosemite- Reinstall OS X
OS X Mavericks- Reinstall OS X
OS X Mountain Lion- Reinstall OS X
OS X Lion- Reinstall Mac OS X
Note: You will need an active Internet connection. I suggest using Ethernet
if possible because it is three times faster than wireless.

Major problems with CS5

We just moved to CS5 and are having major problems with crashing and losing text. I haven't seen these kind of issues since beginning the Indesign/Incopy workflow way back in CS2. I've got dozens of users (Indesign and Incopy) slamming me with complaints of crashing. Indesign crashes when exporting to Incopy (usually when exporting a layer), Incopy users are complaining of crashing when peforming copy/paste either from Word or from within Incopy. Also have had incidents where the text in the Incopy story just disappears or the stories corrupt and will not open in the layout or as a standalone file. Trying to open one will crash the application.
Other departments in our organization who do not use Incopy are not experiencing crashing issues with Indesign CS5, so I have to believe the problem is Incopy.

Try moving everything to a local harddrive and working on a file there. If you don't get the crashing then you can start checking the network. And please, one thread is enough.
Bob

I bought an iphone 5 in the United States. It has major problems with the video. In Italy not fix it. What am I to do?? back in the United States

I bought an iphone 5 in the United States. It has major problems with the video. In Italy not fix it. What am I to do?? back in the United States

The iPhone warranty is not international. If you bought it in the US you can only get service in the US. You will need to take it in to an Apple store in the US.

I had a major problem with my PC yesterday, and subsequently lost Mozilla Foxfire. When I reloaded it onto my PC it opened up with "Welcome to AOL - Mozilla Foxfire". I don't want AOL attached or tagged to Foxfire. How I do prevent that? And hopefully I h

I had a major problem with my PC yesterday, and subsequently had to reload Mozilla Foxfire. When reloaded, it opened with "Welcome to AOL - Mozilla Foxfire". I don't want AOL associated or tagged with Foxfire. I went in to "Programs and Files" and deleted everything with AOL, including Quicktime. Tried loading Foxfire again, but it still opened with AOL tagged. I do use AOL for emails and some browsing, but I want to use Foxfire soley for browsing and search engine. And yes, I did also reload AOL. Can't seem to figure out why AOL is tagging onto Foxfire. Hopefully I have not lost all of my Foxfire Bookmarks - that would really suck.
== User Agent ==
Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.0; Trident/4.0; SLCC1; .NET CLR 2.0.50727; Media Center PC 5.0; .NET CLR 1.1.4322; InfoPath.2; .NET CLR 3.5.30729; .NET CLR 3.0.30729)

Hello Larry.
Hopefully this support article is what you need:
http://support.mozilla.com/en-US/kb/How+to+set+the+home+page

Anyone else having major problems with Safari 5.1 on Snow Leopard?

is anyone else having major problems with Safari 5.1 on Snow Leopard?
- address bar and search box are not resizing with browser window. the address bar and seach box set their size to the window when Safari is launched and remain that size.
- anytime i try to customize toolbar items disappear and i have to restart Safari to get them to appear.
- some 3rd party icons just remove themselves from the toolbar after a period of time
- when i drag a page from the tab bar to create it's own browser window the window disappears but is listed in the windows menu bar. when i select that window from the menu bar the window appears but i can't click on anything.
I've repaired permissions numerous times, reinstalled safari numerous times and restarted my machine numerous times and the issues all remain. i've never had any issues with Safari until now and 5.1 is looking like a huge mess.
besides the bugs above, has anyone had any luck with 1password working with Safari 5.1?

ok, i narrowed most of my issues down to Web Snapper and Videobox by TastyApps. Removed both of those and now everything works better.
I went out to lunch and came back an hour later and magically ALL of my previous toolbar icons that were added to my previous version of Safari appeared. Very strange.
as for 1password, it wasn't working at all before when i posted. everytime i tried installing the extension via the app my, Safari would open a window and hang (never load). I just tried it again and it seems to now be working.

The ios8 update is causing innumerable problems with my ipad. The info from my calendar just disappeared, I am typing blind with the keyboard most of the time, and I cannot upload pics or paste to FB. When will this be fixed and what can I do in the

The ios8 update is causing innumerable problems with my ipad. The info from my calendar just disappeared, I am typing blind with the keyboard most of the time, and I cannot upload pics or paste to FB. When will this be fixed and what can I do in the Meantime?

Have you tried yesterday's update to iOS8.0.2?
iOS 8.0.2
This release contains improvements and bug fixes, including:
• Fixes an issue in iOS 8.0.1 that impacted cellular network connectivity and Touch ID on iPhone 6 and iPhone 6 Plus
• Fixes a bug so HealthKit apps can now be made available on the App Store
• Addresses an issue where 3rd party keyboards could become deselected when a user enters their passcode
• Fixes an issue that prevented some apps from accessing photos from the Photo Library
• Improves the reliability of the Reachability feature on iPhone 6 and iPhone 6 Plus
• Fixes an issue that could cause unexpected cellular data usage when receiving SMS/MMS messages
• Better support of Ask To Buy for Family Sharing for In-App Purchases
• Fixes an issue where ringtones were sometimes not restored from iCloud backups
• Fixes a bug that prevented uploading photos and videos from Safari
For information on the security content of this update, please visit this website:
http://support.apple.com/kb/HT1222

I have a major problems with adobe air.

i have a major problems with adobe air. day before yeasterday it work. now it tell me that it is musconfigure. so i have tried a download it again. but still not working.

You really need to explain what you are doing, and what your "major problems" are. We do not even know if you mean the AIR runtime, or AIR SDK? Nor your operating system.

10.5.7 update results in major problem with external drives

Similar Messages

Maybe you are looking for