10.6.4 Update USB Palm Connection Lost

Since updating to 10.6.4 my Tungsten T4 does not connect through usb. I tried installing Missing Sync and was able to connect through Bluetooth transport monitor for usb does not work. I can use the USB port in Drive Mode which places the Internal and SD disks on the desktop.
Any suggestions appreciated.
Eli
imac 17in 800 Mac OS X (10.4.1)

Problem resolved. Original post based on the use of usb port on imac keyboard. When I changed to a usb port on the imac itself missing sync usb worked without error. While prior to the update I could sync my palm through the keyboard port, it appears that 10.6.4 changed how the keyboard usb hub works.
Eli

Similar Messages

AirPort Client Update 2009-002 Connection Lost

I just installed the AirPort Client Update 2009-002 and now when my computer goes to sleep it loses the internet connection. It reconnects when it awakes from sleep but I need the connection to stay alive even when the computer is in sleep mode.
Was something wrong before or is something wrong now? How can I get the old functionality back? I've looked for an option but can't find anything. Thanks for your help!

I think I'm having the exact same problem, so I'm posting here instead of starting a new topic.
Before a few days ago I was only using a PB G4 with 10.4.11 and an Airport Extreme 801.11n and didn't have any troubles with this set up. I could close the Powerbook, open it up later and almost immediately have access to my wifi. Or, I could leave it open and it would maintain a connection even when no activity (by me, physically) was going on.
I recently got a new MBP (and thus 10.6, which I updated to 10.6.2). If I close the MBP, putting it to sleep, and then open it, I can not access my network. I get the connection timeout message you mentioned. But here's the thing, I also can't get online with my older Powerbook.
I also also tried this: having both side by side and working. I close the MBP, leaving the PB open. I wait a few minutes and try reloading a page on the PB and it says I'm not connected and it refuses to connect.
The only solution I've found so far seems to be to pull the power plug out of the base station, plug it in, and wait a minute or two. I'm then able to access my wifi again.
Did the software update somehow mess with my base station? It's running version 7.3.2.
Do I need to trash some setting? Do I need to tweak some network setting in 10.6 that I don't know about?
I wish I knew if I was having the problems in the few hours between using 10.6 out of the box and updating to 10.6.2 (and a few other things), but I don't think I ever put it to sleep during that time.

When i go to the updates in Appstore : Connect lost to Itunes

My appstore updates go not !!!

I did what they said but it still had me sign in and took me to the Virfying. Still does not work

Connection lost problem while updating my Nokia As...

Dear All,
I face a connection lost problem while I am updating Nokia Asha 200 using Nokia Suite
I installed Nokia software too many times, and tried to repair it. Also, I used another USB cable, but the problem still happen
While it is installing the software, it suddenly stops and show connection lost to your phone.
When I try to restart and reconnect the USB cable, the problem still happen
Nokia200
V 10.61
02-03-12
RM-761
Thanks in advance

Dear Farby
Thanks for your kind and quick reply.
please note that I tried again now, and when the messages for connection lost appears again, I waited for 5 minutes, and nothing happens
because it shows me to do steps, as follows :
1. Disconnect USB cable from phone.
2. restart your phone
3. reconnect the USB cable
4. Wait for the installation to continue.
and when I do these steps, the phone restarts in a test mode, all I see is a test mode message over its screen.
I believe that this is a fatal error which happens through the installation process and which leads to unsuccessful installation
I lost hope in updating the software of this phone, escaially I need to do so, because I face problems with these phone, which doing a hard reset even don't fix.
Thanks again, Farby ... for your help
Regards,

E52 unable to update firmware - connection lost

When I use the E52 Device Manager control panel to check for new software updates it informs me that a new version of the firmware is available "v.022.009", I select "Accept" to download the update and the display stays on the "Downloading" screen without indicating any progress and then eventually says "Connection lost during download".
I'm using a WiFi connection to the internet.
Any ideas as to why the update will not download?

Are you using Nokia PCSuite with Software updater? Connect with a compatible USB cable. That's the best secure way to perform an update.
‡Thank you for hitting the Blue/Green Star button‡
N8-00 RM 596 V:111.030.0609; E71-1(05) RM 346 V: 500.21.009

While updating my apps, I lost my wi-fi connection. I have since tried to update the apps several times...but none of them are updating. Each time I try to update the apps, I enter my password, but then nothing happens. Thank you - Chris

While updating my apps, I lost my wi-fi connection. I have since tried to update the apps several times...but none of them are updating. Each time I try to update the apps, I enter my password, but then nothing happens. Thank you - Chris

Hold the power button and the home button down until the screen goes black and the apple logo appears. This will do a reset and you should be able to update your apps then.

HT201263 My phone is stuck on insert usb cable connect to itunes screen. this happened during my iOS 7 update.

I was updating my iPhone 4S to the iOS 7 system. During update my phone froze. It's stuck on insert USB cable connect to itunes screen. I've already tried turning my phone off holding Home key while inserting my cord into phone and nothing worked. I've tried DFU mode and that wont work either. What the heck do I do now? So annoyed with this.

I've also restarted my computer and still nothing.

TS1398 Updated to ios6 now lost all wifi connection both iPad and iPhone no longer connects to wifi

Updated to ios6 now lost all wifi connection both iPad and iPhone no longer connects to wifi

not much response in here which surprises me...
Anyway... AS I am still looking for answers, I will share a couple of points that I realised...
in Airport Utility, I noticed that my iphone MAC address was actually showing as client connected, despite my phone network showing the spinning wheel next to the network name for ever and never actually connecting.
I am currently testing the router mode in Network to be on DHCP and NAT mode with a range from .2 to .200
My phone is now connected....
Everything seems to be ok and happy so far...
strange that this router and phone have worked together for at least a couple of years, the phone works everywhere else, and all other toys connect to my WIFI just fine. the list is as follow:
airport extreme
Zeppelin air
2x apple tv
2 ipads
iphone 4s
2 mac
1 pc
I have litterally just hard reset the router with a pin just now as a last resort... same...
I will leave the router as DHCP & NAT until a potential firmware or OS update...

Time Capsule Hangs with USB Drive Connected after installing 10.5.6 update

The 10.5.6 update basically made my External USB Disk connected to the Time Capsule unusable. I've repaired the permissions as suggested in other posts - this did not fix the problem.
I was unable to perform any incremental backups initially after the 10.5.6 update, so I archived my sparsebundle and created a new one by doing a full fresh backup - which completed successfully. However, after the backup, I was unable to connect to the Time Capsule or the USB drive connected to the Time Capsule via Finder - when trying to connect, my computer hangs and I'm forced to do a hard restart of BOTH my computer AND the Time Capsule, if I just restart one or the other the problem persists. If I let the connection attempt run long enough I get an "Error Code: -8072" message and still have to do a hard restart. After the hard restart of my computer and Time Capsule I'm able to connect to the Time Capsule and the USB drive connected to Time Capsule just fine. However, once the Time Machine backup runs again - the same problem returns, I can no longer access the Time Capsule or the USB drive connected to Time Capsule via Finder and have to do a hard restart of BOTH my computer AND Time Capsule. This 10.5.6 update has been havoc, anyone have the same troubles or ideas for resolving this? Before updating to 10.5.6 my system was working flawlessly with Time Capsule and the connected USB drive.
UPDATE: I've just verified that this problem only occurs with my external LaCie Hard Drive connected to Time Capsule via USB. If I disconnect my LaCie Hard Drive from the Time Capsule and restart the Time Capsule everything works fine (backups, access to Time Capsule Disk from Finder). If I connect the LaCie Hard Drive via USB to the Time Capsule, I am able to access the LaCie Hard Drive in Finder UNTIL the next Time Machine backup. After the first Time Machine backup with the USB drive connected, I can no longer access the USB drive from Finder - Finder hangs and eventually produces "Error Code: -8072". If I disconnect the USB drive, then plug it back in - Finder no longer hangs and I can access the drive connected to Time Capsule until the next backup occurs.
Anybody have ANY ideas? This worked fine before the 10.5.6 update!

I am having a similar problem. Never tried it before installing 10.5.6, but have a Time Capsule (500GB) with a 1TB WD MyBook Essential Edition connected via USB. Hardware is password protected by authorized users of network and needs separate login to access. When I initially set it up, it worked fine (though too difficult to set up). The WD storage drive showed up in Finder window as a subset of the Time Capsule after clicking on the Time Capsule icon. I had an "-8072" error message yesterday that I ignored, but then the file contents of the WD storage drive took forever to be viewed in Finder (though video files could be accessed wirelessly). Today started having a problem... coincidentally?... after a Time Machine backup, and got the message: "The operation could not be completed. An unexpected error occurred (error code -8072)." Now I am unable to get into the WD drive when I click on "Connect As" on the Time Capsule icon in the Finder menu... I just get the -8072 error. I no longer even see the Time Capsule disk as a subset of the Time Capsule icon in the Finder Toolbar.
What is going on???

Hi, i just try to update my 3g in itunes unfortunatly it got error while updating it asked me to restore update but unable to restore it , now my 3g i locked and on screen it displying usb symbol connect to itunes ,please help me regarding this

hi, i just try to update my 3g in itunes unfortunatly it got error while updating it asked me to restore update but unable to restore it , now my 3g i locked and on screen it displying usb symbol connect to itunes ,please help me regarding this

I suspect your error was 1015, not 1051. This usually involves a jailbroken iPhone, use Google to find your solution.

HT5573 While updating my laptop i lost my internet connectivity. when i tried updating it again ,it shows network error. what i am supposed to do?

While updating my laptop i lost my internet connectivity. when i tried updating it again ,it shows network error. what i am supposed to do?

Delete and recreate your settings in the Network preference pane. If you're connecting to a wireless network, also delete the AirPort network password(s) in the Keychain Access application.

Blue Screen or Connection Lost using USB-5680-01

Hi, we have problem using USB-5680-01 RF Power Meter.
We have installed the NI-568x 1.1 driver and we got random Blue Screen or connection lost with the PM. We need to disconnect and reconnect physically the USB cable to be able to reopen a reference to the PM. We have tried on Windows 7 and Windows Server 2008 machine both 64bits with the same result. It occur on multiple PC.
We tired with powered USB hub, and directly connected to the PC with the same result.
I made a VI to reproduce the problem. It's attached to this message.
Do you have a patch that fix this issue.
Thank You
Dany Allard
Attachments:
national_instruments_usb-5680.zip ‏216 KB
ReadPowerMeter5680.vi ‏16 KB

JohnFenner wrote:
I can contact you directly to try out some beta software, if you're interested.
Yes please
Thank you
Dany Allard

"Connection lost" while updating phone software in...

Good day.
I got a notification on the Suite that there is a phone update (v11.40) for my Nokia C2-01. I wanted to upgrade my phone's software so I decided to go on with it.
The backup phase is good, but later it said "Connection lost" during the installation.
I canceled the installation, and when I turned on my C2-01, it shows "Test mode" on the screen. So I switched it off. Luckily after a few minutes I tried to switch it on again and the phone goes back to normal.
What should I do to avoid this situation from happening again? I'm using version 3.6 of the software and I hope this won't happen in version 3.7. Thank you.

Can you tell me the OS of the PC that you are using? You can try this troubleshooting and see if it will work:
In Windows 7 and Windows Vista the reason for failure may be caused by windows trying to download and install additional conflicting device drivers during the update process.
To disable windows device installation for the duration of the Nokia Suite process do to following:
Access "Control Panel" and select "System and Security", and from there select "System"
Next select "Advanced System Settings" and then the "Hardware" tab, and select "Device Installation Settings"
From "Device Installation Settings", choose "No, let me choose what to do" and next select "Never install driver software from windows update"
Click "Save Changes"
After this process please try to run the Nokia Suite process again. You may need to manually connect to your device again using Nokia Suite's "Add New Device".
Remember to enable the windows device driver settings after successfull installation.

TS1398 Hi all since updating to ios 6 when trying to use facetime I keep getting connection lost and no ringing tone has Apple got a fix for this issue

Hi all since updating to ios 6 when trying to use facetime I keep getting connection lost and no ringing tone has Apple got a fix for this issue

Using FaceTime http://support.apple.com/kb/ht4319
Troubleshooting FaceTime http://support.apple.com/kb/TS3367
The Complete Guide to FaceTime: Set-up, Use, and Troubleshooting Problems
http://tinyurl.com/32drz3d
 Cheers, Tom

My Ipod touch 4th generation facetime has just stopped working it will ring out and then try to connect and each time says connection lost. The Ipod has been reset hardware etc and the software is all update .

my Ipod touch 4th generation facetime has just stopped working it will ring out and then try to connect and each time says connection lost. The Ipod has been reset hardware etc and the software is all update .

Hi hema87,
Thanks for using Apple Support Communities. This article has some troubleshooting steps you can try if FaceTime is timing out:
iOS: Troubleshooting FaceTime
http://support.apple.com/kb/ts3367
Cheers,
- Ari

10.6.4 Update USB Palm Connection Lost

Similar Messages

Maybe you are looking for