10.6 Verbose mode stops at ACPI_SMC_PlatformPlugin::start....

Macbook not booting and stalls at spinning gear.
Tried many things but ended up booting into verbose mode and it stops at
ACPI_SMC_PlatformPlugin::start - watiForService(resourceMattching(AppleIntelCPUPowerManagement) timed out.
Previously in the boot, it says it failed to load that kext because the link failed.
- Tried repairing permissions
- Netbooting into AST and running MRI. No errors. Reset SMC and NVRAM. No change.
- Swapped RAM
- Made image and restored to a new hard drive. Same problems.
- Booted different computer from the harddrive. Still get spinning gear.
- Swapped hard drive for a working one from another laptop and it booted fine.
Any thoughts before I wipe the HD it and start from scratch?

Dont wipe the hard drive!
Just had this problem on a macbook pro 2011 at my work (computer repair business). The problem occurred after switching out the hard drive and hard drive cable. Tried booting an Apple Hardware Test, by install disk, or by bootable USB OSx. Each time the verbose popped up before completing boot and ended at a failure of the load of the driver regarding cpu power management.
Ultimately, the problem was a corruption of the firmware, which is embedded in flash-based rom chips on the logic board. The Apple website has the firmware for your model available and it should boot from the disk without trouble.
Incidentally, all attempts to boot failed except when booting to the OSx Lion full install from USB. This alone seemed to bypass the corruption. Regardless, the firmware restore should do it.
So don't wipe your drive.

Similar Messages

HELP! MacMini starting up in Verbose Mode

Hi,
My Mac Mini seems to be sarting up in Verbose Mode (black background with white type). Any ideas why this is happening? and how do I stop it?
I've run Disk First Aid off the installion CD and its fixed all the problems that it found, but it still happening. Do I need to wipe the HD and start all over again, or try to just re-install the OS?
Any words of wisdom?
Thanks!
Su
Mac Mini Mac OS X (10.4.9)

also download and install onyx
http://www.titanium.free.fr/pgs2/english/download.html
once installed, open onyx and go to the parameters tab, then go to the tab under that named login. find the one that says startup mode. select normal mode and it should reset it to normal.
hope this helps
-bjarec

MBP early 2011, slow boot, have tried: PRAM reset, SMC reset, permissions, login items, verbose mode. It stops for 2mins on spinning gear

I've read quite a few similar posts and tried most of the advice given. It seems to me though that it could be a number of things, but I just haven't found the right fix. I understand that getting an SSD would help greatly, but the MBP started doing the slow boots quite suddenly, so I don't think it's because of gradually filling the HDD with stuff. When I startup in verbose mode, it stops at running fsck, and just stays there for a while. Working in Lion is not as slow as the startup, but definitely not as fast as it should be, and shut downs are not slow at all.
I have used about 500gb of the 750gb HDD, and startup times used to be at about 30 secs, and are now over 2 mins, without increasing or decreasing.

Update: also tried Repair Disk and even reinstalling Lion (not clean).

Freezing at startup - weird message when starting up in verbose mode

My macbook pro, only about 2 months old, freezes a lot while its starting up. i have to keep turning it off and on for it to work. It gets stuck at the grey screen with the apple and the loading icon.
I decided to start up in verbose mode and maybe i can see what the problem is. So i did just that and i got this error message:
SATA WARNING: completing a zero block transfer.
it keeps repeating that message and scrolling down the screen forever.
I have no idea what that could be.

Most likely a problem with the disk and/or some corruption of the directory. Be sure to back up your own data if you haven't done so already. Then boot from your install disk and go to the menu bar and select Disk Utility and then Repair Disk. If it reports a problem and fixes it, run it again until everything comes up clean. If it reports a problem it can't fix you could invest in DiskWarrior, or, if you have AppleCare I believe you got a free copy of TechTool, you could try running that.
Francine
Francine
Schwieder

How to start up MAC mini only in the verbose mode (command line) , no GUI

Can anyone let me know how I can set up the mac mini to ALWAYS boot into a verbose mode only, no GUI interfaces at all?
Mac Mini Mac OS X (10.4.6)
Mac Mini Mac OS X (10.4.6)

Hi, Andy your replies are really helpful. I did tried your method and also followed the link http://www.oreillynet.com/pub/h/348
Now my mac mini - Tiger seems hanging forever at the boot up screen. A Apple log showed up with a message "Starting Mac OS X ..." and now almost 5 minutes passed, nothing happened ...

How to start Weblogic 9.1 in verbose mode

Hi all,
I need to start Weblogic 9.1 in verbose mode.
We have just recently migrated from weblogic 8 sp3 to weblogic 9.1. In weblogic 8 sp3, the option
"-Dweblogic.ejb20.cmp.rdbms.codegen.verbose=true"
would work but it doesn't work with Weblogic 9.1.
Can anyone tell me how to do the same?
Thanks and regards,
Sachidanand

If you close Firefox while in full screen mode then Firefox should reopen in full screen mode the next time.
That choice is saved in the localstore.rdf file in the profile folder.
*http://kb.mozillazine.org/localstore.rdf

10.4.9 Server Starts in Verbose Mode

When I restart my G4 Server, it looks like it is starting like normal, shows the blue startup screen and says Mac Server is starting up, but when the bar reaches the end, it briefly goes to an all blue screen and then moves to a black screen with white text(verbose mode I think).
After searching the forums, I tried forcing the mac os x startup by holding command and x during startup, but nothing changes. I have also tried entering:
sudo nvram boot-args=""
to boot up normally, but still no change. I have tried repairing the disk in disk utility, booting from an external hard drive, but still boots in verbose mode.
Any help would be great.
1.6GHz G5 iMac Mac OS X (10.4.10)

Hi Dan-Cherokee:
What happens if you boot from the installer disk?
In the meantime try resetting the PRAM (ParameterRAM). Restart the server and hold down the command, alt, P and R keys at the same time. You should hear the start-up chime, keep them depressed until you hear the chime again, keep them depressed for a further start-up chime, now release the keys and immediately hold down the shift key. You will have to keep this depressed for some time as you are now booting in safe mode/boot. Eventually you will see the log in window with Safe Mode/Boot (in red) displayed, release the shift key and log in as normal, wait a few seconds and click on the trash icon, you should see a folder that has a long number for its name or possibly be called recovered items, delete this folder and reboot as normal. Safe Mode does a thorough check of your drive and directory as well as flushing system caches (this is what gets dumped into the trash).
Hope this helps – Tony

Last week I've install Mac OS X Mountain Lion and then after the installation finish my IMAC start up in verbose mode. How can I turn off this mode and start my IMAC normally. I've try to key in the code "sudo nvram boot-args=" in terminal also.

Last week I've install Mac OS X Mountain Lion and then after the installation finish my IMAC start up in verbose mode. How can I turn off this mode and start my IMAC normally. I've try to key in the code "sudo nvram boot-args=" in terminal also.
Thank you for all of your answer.

I've seen it mentioned on here that a PRAM reset may solve it:
Reset PRAM
Shut down the computer.
Locate the following keys on the keyboard: Command, Option, P and R.
You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.

My MacBook pro will not startup. I get a blank grey screen no logo appears so I can't chooseadiffer t drive nor boot from DVD. Safe mode and verbose mode also don't change blank screen.

It was running slow with the colored spining appearing often. This started happening weeks ago with Yosemite so I formatted the disk with the DVDs that came with the mid 2011 MacBook pro, 10.6.8. I then installed Yosemite on an external drive and this morning i was booted from the external hd with Yosemite and it stopped recognizong mouse clicks so I forced a restart and now I'm stuck with the blank grey screen. Safe mode and verbose mode also do not work.

Lao Bo,
yes, you can locate and copy a file from your HD to a USB key using UNIX commands. If you know the exact name of the file which you’re trying to locate, try this:
find / -iname filename -print
This command will search your entire internal disk for the particular filename. If you know that it’s within a particular user account, then you can save search time with this variation:
find /Users/username -iname filename -print
Either variation of this command will print all files found which have the given filename. Presuming that you’re able to identify the correct file, you can copy it to a USB key using the command
cp -p filename_returned_by_find /Volumes/USB_volume
If you’re not sure which volume name your USB key has, this command will show you what the possibilities are:
ls /Volumes
Please let me know if you have any trouble with these commands.

Normal Startup Messages (System.log; Intel Verbose Mode)?

Over this past weekend, I wanted to test the backup I had for my 24" iMac. I had always used Apple's Backup program that comes with .Mac when I had my PowerBook, and never tested it. This was bad, because it didn't work when I actually needed it.
I also suspected there might be something slightly wrong with my iMac, so equipped with about 4 hours and my install DVDs i went to work.
The only thing I've done so far is get all the Apple updates and setup my iChat account. I changed to boot in verbose mode, and found that the eery messages that scared me prior to doing my reinstallation of OS X (I zeroed the drive, then did a full install) were still there.
Here is my entire System.log:
Jan 30 09:22:35 mike-barcas-computer sudo: Mike : TTY=ttyp1 ; PWD=/Users/Mike ; USER=root ; COMMAND=/usr/sbin/nvram boot-args=-v
Jan 30 09:22:48 mike-barcas-computer shutdown: reboot by Mike:
Jan 30 09:22:48 mike-barcas-computer SystemStarter[279]: authentication service (287) did not complete successfully
Jan 30 09:22:48 mike-barcas-computer kernel[0]: (295: ps)tfp: failed on 0:
Jan 30 09:22:48 mike-barcas-computer kernel[0]: (295: ps)tfp: failed on 0:
Jan 30 09:22:48 mike-barcas-computer kernel[0]: (295: ps)tfp: failed on 0:
Jan 30 09:22:49 mike-barcas-computer kernel[0]: (322: ps)tfp: failed on 0:
Jan 30 09:22:49 mike-barcas-computer SystemStarter[279]: The following StartupItems failed to properly start:
Jan 30 09:22:49 mike-barcas-computer kernel[0]: (322: ps)tfp: failed on 0:
Jan 30 09:22:49 mike-barcas-computer SystemStarter[279]: /System/Library/StartupItems/AuthServer
Jan 30 09:22:49 mike-barcas-computer kernel[0]: (323: ps)tfp: failed on 0:
Jan 30 09:22:49 mike-barcas-computer SystemStarter[279]: - execution of Startup script failed
Jan 30 09:23:08 localhost kernel[0]: hi mem tramps at 0xffe00000
Jan 30 09:23:08 localhost kernel[0]: PAE enabled
Jan 30 09:23:08 localhost kernel[0]: 64 bit mode enabled
Jan 30 09:23:08 localhost kernel[0]: standard timeslicing quantum is 10000 us
Jan 30 09:23:08 localhost kernel[0]: vmpagebootstrap: 512343 free pages
Jan 30 09:23:08 localhost kernel[0]: migtable_maxdispl = 71
Jan 30 09:23:08 localhost kernel[0]: Enabling XMM register save/restore and SSE/SSE2 opcodes
Jan 30 09:23:08 localhost kernel[0]: 80 prelinked modules
Jan 30 09:23:08 localhost kernel[0]: ACPI CA 20060421
Jan 30 09:23:08 localhost kernel[0]: AppleIntelCPUPowerManagement: ready
Jan 30 09:23:08 localhost kernel[0]: AppleACPICPU: ProcessorApicId=0 LocalApicId=0 Enabled
Jan 30 09:23:08 localhost kernel[0]: AppleACPICPU: ProcessorApicId=1 LocalApicId=1 Enabled
Jan 30 09:23:08 localhost kernel[0]: Copyright (c) 1982, 1986, 1989, 1991, 1993
Jan 30 09:23:08 localhost kernel[0]: The Regents of the University of California. All rights reserved.
Jan 30 09:23:08 localhost kernel[0]: using 10485 buffer headers and 4096 cluster IO buffer headers
Jan 30 09:23:08 localhost kernel[0]: Enabling XMM register save/restore and SSE/SSE2 opcodes
Jan 30 09:23:08 localhost kernel[0]: Started CPU 01
Jan 30 09:23:08 localhost kernel[0]: IOAPIC: Version 0x20 Vectors 64:87
Jan 30 09:23:08 localhost kernel[0]: ACPI: System State [S0 S3 S4 S5] (S3)
Jan 30 09:23:08 localhost kernel[0]: Security auditing service present
Jan 30 09:23:08 localhost kernel[0]: BSM auditing present
Jan 30 09:23:08 localhost kernel[0]: disabled
Jan 30 09:23:08 localhost kernel[0]: rooting via boot-uuid from /chosen: 771A8047-7B26-48DC-ABB6-89E46168EE40
Jan 30 09:23:08 localhost kernel[0]: Waiting on <dict ID="0"><key>IOProviderClass</key><string ID="1">IOResources</string><key>IOResourceMatch</key><string ID="2">boot-uuid-media</string></dict>
Jan 30 09:23:08 localhost kernel[0]: USB caused wake event (EHCI)
Jan 30 09:23:08 localhost kernel[0]: FireWire (OHCI) TI ID 8025 built-in now active, GUID 0017f2fffe6db760; max speed s800.
Jan 30 09:23:08 localhost kernel[0]: Got boot device = IOService:/AppleACPIPlatformExpert/PCI0@0/AppleACPIPCI/SATA@1F,2/AppleAHCI/PRT2 @2/IOAHCIDevice@0/AppleAHCIDiskDriver/IOAHCIBlockStorageDevice/IOBlockStorageDri ver/ST3500641AS Q Media/IOGUIDPartitionScheme/AppleHFS_Untitled2@2
Jan 30 09:23:08 localhost kernel[0]: BSD root: disk0s2, major 14, minor 2
Jan 30 09:23:08 localhost kernel[0]: CSRHIDTransitionDriver::probe: -v
Jan 30 09:23:08 localhost kernel[0]: CSRHIDTransitionDriver::start before command
Jan 30 09:23:08 localhost kernel[0]: CSRHIDTransitionDriver::stop
Jan 30 09:23:08 localhost kernel[0]: IOBluetoothHCIController::start Idle Timer Stopped
Jan 30 09:23:08 localhost kernel[0]: Jettisoning kernel linker.
Jan 30 09:23:08 localhost kernel[0]: Resetting IOCatalogue.
Jan 30 09:23:08 localhost kernel[0]: GFX0: family specific matching fails
Jan 30 09:23:08 localhost kernel[0]: Matching service count = 1
Jan 30 09:23:08 localhost kernel[0]: Matching service count = 2
Jan 30 09:23:08 localhost kernel[0]: Matching service count = 2
Jan 30 09:23:08 localhost kernel[0]: Matching service count = 2
Jan 30 09:23:08 localhost kernel[0]: Matching service count = 2
Jan 30 09:23:08 localhost kernel[0]: Matching service count = 2
Jan 30 09:23:08 localhost kernel[0]: NVDANV40HAL loaded and registered.
Jan 30 09:23:08 localhost kernel[0]: GFX0: family specific matching fails
Jan 30 09:23:08 localhost kernel[0]: wl0: Broadcom BCM4328 802.11 Wireless Controller
Jan 30 09:23:08 localhost kernel[0]: 4.80.76.0Previous Shutdown Cause: 3
Jan 30 09:23:08 localhost memberd[38]: memberd starting up
Jan 30 09:23:08 localhost mDNSResponder-108.2 (Aug 25 2006 14: 50:48)[31]: starting
Jan 30 09:23:10 localhost lookupd[44]: lookupd (version 369.6) starting - Tue Jan 30 09:23:10 2007
Jan 30 09:23:13 localhost diskarbitrationd[37]: disk0s2 hfs 8AAF2196-1366-34AB-B7BC-3D96F131E9AD Macintosh HD /
Jan 30 09:23:13 localhost DirectoryService[43]: Launched version 2.1 (v353.5)
Jan 30 09:23:13 localhost kernel[0]: yukonosx: Ethernet address 00:16:cb:9e:39:58
Jan 30 09:23:13 localhost kernel[0]: AirPort_Brcm43xx: Ethernet address 00:17:f2:99:63:9d
Jan 30 09:23:13 localhost lookupd[56]: lookupd (version 369.6) starting - Tue Jan 30 09:23:13 2007
Jan 30 09:23:14 mike-barcas-computer configd[35]: setting hostname to "mike-barcas-computer.local"
Jan 30 09:23:14 mike-barcas-computer kernel[0]: Registering For 802.11 Events
Jan 30 09:23:14 mike-barcas-computer /System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow: Login Window Application Started
Jan 30 09:23:14 mike-barcas-computer kernel[0]: [HCIController][setupHardware] AFH Is Supported
Jan 30 09:23:16 mike-barcas-computer mDNSResponder: Adding browse domain local.
Jan 30 09:23:16 mike-barcas-computer loginwindow[50]: Login Window Started Security Agent
Jan 30 09:23:17 mike-barcas-computer kernel[0]: SetCryptoKey T: len 16, idx 0
Jan 30 09:23:17 mike-barcas-computer kernel[0]: SetCryptoKey R: len 16, idx 1
Jan 30 09:23:17 mike-barcas-computer /System/Library/PrivateFrameworks/Apple80211.framework/Resources/airport: Currently connected to network Ferrari
Jan 30 09:23:20 mike-barcas-computer configd[35]: executing /System/Library/SystemConfiguration/Kicker.bundle/Contents/Resources/enable-net work
Jan 30 09:23:20 mike-barcas-computer configd[35]: posting notification com.apple.system.config.network_change
Jan 30 09:23:20 mike-barcas-computer lookupd[88]: lookupd (version 369.6) starting - Tue Jan 30 09:23:20 2007
Jan 30 09:23:20 mike-barcas-computer ntpdate[126]: no servers can be used, exiting
Jan 30 09:23:21 mike-barcas-computer configd[35]: target=enable-network: disabled
The lines that concern me are the ones bolded at the top of System.log
The other thing that is a bit unnerving to me is that when I have it set to boot in verbose mode, and then restart the computer, I get a screen that looks out of place. It is a box with a dark background in the center of the screen with text in there, and then it quickly switches to full screen verbose mode. The first line of full screen verbose mode (which is what I'm used to since I always used verbose mode on my PowerBook) is this one:
Jan 30 09:23:08 localhost kernel[0]: hi mem tramps at 0xffe00000
In the centered text, it mentions something about "loading drivers" followed by many lines of periods. It is only up for about 5 seconds, and then switches to full screen verbose mode. Is that centered window for verbose mode new to intel Macs? I never recall seeing it on my PowerBook.
When i googled around for the "hi mem tramps" message, i found it might be linked to bad ram. I used memtest and did 3 passes to check the ram, and it found no errors.
Are these messages in System.log normal?
Thanks!

Hi, Mike.
First, please don't use the "scatter gun" or "post everywhere" approach. I see you've also post the same question here. I appreciate your urgent desire for help, but it would be very annoying to anyone answering questions here to spend time researching your question in one post, only to find it already answered in another place where it was also posted. The "scatter gun" approach is a good way to get all your future posts ignored.
According to what I read in the second post of this topic on another forum, I suspect you may have a Startup Item that's causing the highlighted messages to be written to system.log. Perhaps some PowerPC code you may have migrated over to your Intel-based Mac if you used the Setup / Migration Assistant to move to the new Mac from a pervious Mac.
There have been numerous posts about the tfp: failed on 0 message, which can be seen in this search of the Discussions. However, I suspect the explanation I've cited above fits your situation.
If an errant Startup Item is the cause, my "Troubleshooting Startup and Login Items" FAQ can help you pin that down if such an item is causing the problem.
As to hi mem tramps…, that may be normal. If you read this item and click on the link for dmesg you'll see a typical output someone else posted as, I suspect, an example of "normal."
Good luck!
Dr. Smoke
Author: Troubleshooting Mac® OS X
Note: The information provided in the link(s) above is freely available. However, because I own The X Lab™, a commercial Web site to which some of these links point, the Apple Discussions Terms of Use require I include the following disclosure statement with this post:
I may receive some form of compensation, financial or otherwise, from my recommendation or link.

Booting in verbose mode after installing Mountain Lion

I installed Mountain Lion on 3 machines. On my iMac I now boot after a cold start in verbose mode. What do I do to stop that? Thanks.

Sorry, that I have no answer, but may be it helps psychologically to know that you are not alone. I have the same problem and maybe worse because the boot process holds at a certain point in single user mode and a root prompt. I have to enter "exit" to make it continue and startup properly. It looks like I have the same HW as you.

Early 2011 MBP stuck on gray screen, verbose mode shows SMC error too

Hi!
I have and early 2011 MBP, running on OS 10.7.5 is continuously stuck at grey screen upon start-up.
I tried the steps as mentioned in Mac OS X: Gray screen appears during startup - Apple Support article apart from reinstalling OS X. The laptop started after every step, but then stopped again. I tried SMC update, that also worked for once, and on the second start up I ended up with a blue screen. During a later attempt, it worked again for a while, but ended with a distorted graphics after 15 mins. AHT (short version) doesn't show any hardware errors. Now the laptop doesn't go further than grey screen at all, and after a minute or so there's a heavy fan activity. The verbose mode also shows and SMC error, smc: : smcinithelper error: mmio regmap ==null - fall back to old smc mode (AHT Shows SMC version as 1.69f4)
What do you advise?

Try this:
Reset the SMC and the NVRAM:
https://support.apple.com/en-us/HT201295
https://support.apple.com/en-us/HT204063
Then try a safe boot:
https://support.apple.com/en-us/HT201262
Any success?
Ciao.

SSRS error - verbose mode

We have a SCCM and use SQL 2012 server for reporting. Recently we have started experiencing a problem where we can browse to the reports and once we do run the reports, it tries to run forever and eventually halts with the following error
An error occurred within the report server database. This may be due to a connection failure, timeout or low disk condition within the database. (rsReportServerDatabaseError)
I have enabled verbose mode on the sql server and restarted the reporting service. Below is the log file where I am hoping someone will be able to tell me what the issue is:
<Header>
<Product>Microsoft SQL Server Reporting Services Version 2011.0110.5058.00 ((SQL11_PCU_Main).140514-1820 )</Product>
<Locale>English (United Kingdom)</Locale>
<TimeZone>GMT Standard Time</TimeZone>
<Path>E:\Program Files\Microsoft SQL Server\MSRS11.INSTANCE2\Reporting Services\Logfiles\ReportServerService__12_18_2014_14_54_36.log</Path>
<SystemName>SRVPRDAPPDB1</SystemName>
<OSName>Microsoft Windows NT 6.2.9200</OSName>
<OSVersion>6.2.9200</OSVersion>
<ProcessID>27476</ProcessID>
<Virtualization>None</Virtualization>
</Header>
<ProcessorArchitecture>AMD64</ProcessorArchitecture>
<ApplicationArchitecture>AMD64</ApplicationArchitecture>
rshost!rshost!4d58!12/18/2014-14:54:36:: i INFO: CLR runtime is initialized.
rshost!rshost!4d58!12/18/2014-14:54:36:: v VERBOSE: Initializing Memory Monitoring
rshost!rshost!4d58!12/18/2014-14:54:36:: i INFO: Derived memory configuration based on physical memory as 268369396 KB
rshost!rshost!4d58!12/18/2014-14:54:36:: v VERBOSE: Supported winsock version is 2.2.
appdomainmanager!DefaultDomain!4d58!12/18/2014-14:54:36:: i INFO: Entered managed ServiceMain in DefaultDomain.
configmanager!DefaultDomain!6728!12/18/2014-14:54:37:: e ERROR: Configuration file element UrlReservation has a invalid VirtualRoot. It will be ignored.
configmanager!DefaultDomain!6728!12/18/2014-14:54:37:: e ERROR: Configuration file element UrlReservation has a invalid VirtualRoot. It will be ignored.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing ConnectionType to '0' as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing SecureConnectionLevel to '0' as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing DisableSecureFormsAuthenticationCookie to 'False' as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing CleanupCycleMinutes to '10' minute(s) as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing MaxActiveReqForOneUser to '20' requests(s) as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing DatabaseQueryTimeout to '120' second(s) as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing RunningRequestsScavengerCycle to '60' second(s) as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing RunningRequestsDbCycle to '60' second(s) as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing RunningRequestsAge to '30' second(s) as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing MaxScheduleWait to '5' second(s) as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing DisplayErrorLink to 'True' as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing WebServiceUseFileShareStorage to 'False' as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing WatsonFlags to '1064' as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing WatsonDumpOnExceptions to 'Microsoft.ReportingServices.Diagnostics.Utilities.InternalCatalogException,Microsoft.ReportingServices.Modeling.InternalModelingException,Microsoft.ReportingServices.ReportProcessing.UnhandledReportRenderingException'
as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing WatsonDumpExcludeIfContainsExceptions to 'System.Threading.ThreadAbortException,System.Web.UI.ViewStateException,System.OutOfMemoryException,System.Web.HttpException,System.IO.IOException,System.IO.FileLoadException,Microsoft.SharePoint.SPException,Microsoft.ReportingServices.WmiProvider.WMIProviderException'
as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing AuthenticationTypes to '4' as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing RSWindowsExtendedProtectionLevel to 'Off' as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing RSWindowsExtendedProtectionScenario to 'Proxy' as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing EnableAuthPersistence to 'True' as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing IsSchedulingService to 'True' as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing IsNotificationService to 'True' as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing IsEventService to 'True' as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing PollingInterval to '10' second(s) as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing WindowsServiceUseFileShareStorage to 'False' as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing MemorySafetyMargin to '80' percent as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing MemoryThreshold to '90' percent as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing RecycleTime to '720' minute(s) as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing MaxAppDomainUnloadTime to '30' minute(s) as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing MaxQueueThreads to '0' thread(s) as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: w WARN: Initializing UrlRoot to default value of '' because it was incorrectly specified in Configuration file as ''.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing IsWebServiceEnabled to 'True' as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing IsReportManagerEnabled to 'True' as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing MaxConnections to '2' as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing Timeout to '10' second(s) as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing AppID to '(Default)' as specified in Configuration file.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Initializing CacheLevel to 'Default' as specified in Configuration file.
resourceutilities!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Reporting Services starting SKU: Standard
configmanager!DefaultDomain!6728!12/18/2014-14:54:37:: e ERROR: Failed to get url configuration section.
configmanager!DefaultDomain!6728!12/18/2014-14:54:37:: e ERROR: Failed to get url configuration section.
configmanager!DefaultDomain!6728!12/18/2014-14:54:37:: w WARN: IsApplicationUrlSubsetOfReportServer() -- Failed to get url configuration section.
configmanager!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Using report server internal url .
configmanager!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Using report server external url .
configmanager!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Using url root .
rshost!rshost!6728!12/18/2014-14:54:37:: i INFO: Configuring maxPhysicalCpu=4, minLogicalCpu=0
rshost!rshost!6728!12/18/2014-14:54:37:: i INFO: Logical processor per physical processor 16
rshost!rshost!6728!12/18/2014-14:54:37:: i INFO: Logical processor per core 2
rshost!rshost!6728!12/18/2014-14:54:37:: i INFO: Maximum logical CPU is 32
library!DefaultDomain!6728!12/18/2014-14:54:37:: e ERROR: Throwing Microsoft.ReportingServices.Diagnostics.Utilities.ServerConfigurationErrorException: No DSN present in configuration file, Microsoft.ReportingServices.Diagnostics.Utilities.ServerConfigurationErrorException:
The report server has encountered a configuration error. ;
servicecontroller!DefaultDomain!6728!12/18/2014-14:54:37:: e ERROR: Error initializing configuration from the database: Microsoft.ReportingServices.Diagnostics.Utilities.ServerConfigurationErrorException: The report server has encountered a configuration error.
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: SQLDump flags: ReferencedMemory, AllThreads, SendToWatson
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: MiniDump flags: DataSegs, UnloadedModules, ProcessThreadData
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Dump on: Microsoft.ReportingServices.Diagnostics.Utilities.InternalCatalogException,Microsoft.ReportingServices.Modeling.InternalModelingException,Microsoft.ReportingServices.ReportProcessing.UnhandledReportRenderingException
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Do not dump on: System.Threading.ThreadAbortException,System.Web.UI.ViewStateException,System.OutOfMemoryException,System.Web.HttpException,System.IO.IOException,System.IO.FileLoadException,Microsoft.SharePoint.SPException,Microsoft.ReportingServices.WmiProvider.WMIProviderException
library!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Minidump location: E:\Program Files\Microsoft SQL Server\MSRS11.INSTANCE2\Reporting Services\Logfiles
library!DefaultDomain!6728!12/18/2014-14:54:37:: v VERBOSE: Setting unhandled exception handler
appdomainmanager!DefaultDomain!6728!12/18/2014-14:54:37:: i INFO: Appdomain:2 WindowsService_0 started.
library!WindowsService_0!6728!12/18/2014-14:54:37:: e ERROR: Throwing Microsoft.ReportingServices.Diagnostics.Utilities.ServerConfigurationErrorException: No DSN present in configuration file, Microsoft.ReportingServices.Diagnostics.Utilities.ServerConfigurationErrorException:
The report server has encountered a configuration error. ;
servicecontroller!WindowsService_0!6728!12/18/2014-14:54:37:: e ERROR: Error initializing configuration from the database: Microsoft.ReportingServices.Diagnostics.Utilities.ServerConfigurationErrorException: The report server has encountered a configuration
error.
library!WindowsService_0!6728!12/18/2014-14:54:38:: i INFO: SQLDump flags: ReferencedMemory, AllThreads, SendToWatson
library!WindowsService_0!6728!12/18/2014-14:54:38:: i INFO: MiniDump flags: DataSegs, UnloadedModules, ProcessThreadData
library!WindowsService_0!6728!12/18/2014-14:54:38:: i INFO: Dump on: Microsoft.ReportingServices.Diagnostics.Utilities.InternalCatalogException,Microsoft.ReportingServices.Modeling.InternalModelingException,Microsoft.ReportingServices.ReportProcessing.UnhandledReportRenderingException
library!WindowsService_0!6728!12/18/2014-14:54:38:: i INFO: Do not dump on: System.Threading.ThreadAbortException,System.Web.UI.ViewStateException,System.OutOfMemoryException,System.Web.HttpException,System.IO.IOException,System.IO.FileLoadException,Microsoft.SharePoint.SPException,Microsoft.ReportingServices.WmiProvider.WMIProviderException
library!WindowsService_0!6728!12/18/2014-14:54:38:: i INFO: Minidump location: E:\Program Files\Microsoft SQL Server\MSRS11.INSTANCE2\Reporting Services\Logfiles
library!WindowsService_0!6728!12/18/2014-14:54:38:: v VERBOSE: Setting unhandled exception handler
resourceutilities!WindowsService_0!6728!12/18/2014-14:54:38:: i INFO: Reporting Services starting SKU: Standard
library!WindowsService_0!5c98!12/18/2014-14:54:38:: e ERROR: Throwing Microsoft.ReportingServices.Diagnostics.Utilities.ServerConfigurationErrorException: No DSN present in configuration file, Microsoft.ReportingServices.Diagnostics.Utilities.ServerConfigurationErrorException:
The report server has encountered a configuration error. ;
library!WindowsService_0!5c98!12/18/2014-14:54:38:: e ERROR: ServiceStartThread: Exception caught while starting service. Error: Microsoft.ReportingServices.Diagnostics.Utilities.ServerConfigurationErrorException: The report server has encountered a configuration
error.
library!WindowsService_0!5c98!12/18/2014-14:54:38:: e ERROR: ServiceStartThread: Attempting to start service again...
rpcserver!DefaultDomain!5c98!12/18/2014-14:54:38:: i INFO: RPC Server started.
servicecontroller!DefaultDomain!5c98!12/18/2014-14:54:38:: i INFO: RPC Server started. Endpoint name ='ReportingServices$MSRS11.INSTANCE2'
rshost!rshost!370c!12/18/2014-14:54:38:: w WARN: Endpoint 2 is enabled but no url is registered for vdir=, pdir=E:\Program Files\Microsoft SQL Server\MSRS11.INSTANCE2\Reporting Services\ReportServer.
rshost!rshost!4e68!12/18/2014-14:54:38:: w WARN: Endpoint 3 is enabled but no url is registered for vdir=, pdir=E:\Program Files\Microsoft SQL Server\MSRS11.INSTANCE2\Reporting Services\ReportManager.
rshost!rshost!4e68!12/18/2014-14:54:38:: i INFO: Endpoint 4 is disabled and no url is registered vdir=, pdir=E:\Program Files\Microsoft SQL Server\MSRS11.INSTANCE2\Reporting Services\ReportServer\ReportBuilder.
resourceutilities!DefaultDomain!6728!12/18/2014-14:54:38:: i INFO: Maximum memory limit is 65536Mb
rshost!rshost!6728!12/18/2014-14:54:38:: i INFO: Derived memory configuration based on physical memory as 67108864 KB
rpcserver!DefaultDomain!432c!12/18/2014-14:54:38:: i INFO: Process monitoring started.
servicecontroller!DefaultDomain!3a4c!12/18/2014-14:54:38:: i INFO: Total Physical memory: 274810261504
Thanks.

This was to do with NIC settings on the SQL server. There was a mis-configuration where data was taking long time to copy. Once we have corrected this, all started to work just fine.

Suddenly, Macbook doesn't boot up in single user mode or verbose mode

Hello, I use the single-user boot up quite often to check permissions and do a fsck after my mac crashes.
I do this by pressing Apple(Command)-S at startup or cmd-V for the verbose mode. I do this all the time.
But now my Mac won't take it anymore. It just refuses to accept any key combo. Any ideas why this is happening?
thanks.

Hi Jose, actually you don't have to boot to single user and repair permission all the time. Just perform that after you update your software and or hardware.
Can you start up normally and then use your keyboard as usual, or is the keyboard refuse to do so?
Try to reset your PRAM and or PMU to refresh your hardware behavior.
http://docs.info.apple.com/article.html?artnum=2238
http://docs.info.apple.com/article.html?artnum=303319
Good Luck.

IMac won't boot up. Stuck in "verbose mode" ??

I've had this problem on and off for a few weeks now. I either restart my iMac after installing some new software-or for other reason- and my computer won't boot up. Sometimes it will stay at the white screen with the grey apple for hours if I leave it there. I've tried all the tricks with key commands. I even reinstalled my software, which worked, but now its happening again. Today, I restarted my iMac, and the same thing is happening, except sometimes it will go into what I've heard called- "verbose mode." The screen is black and white command text appears in the upper left hand corner. Here are some examples of what appears...
No Airport driver found.
Exited abnormally. Bad system call.
Repawning too quickly! throttling
10 more failures without living at least 60 seconds will cause job removal.
Will restart in 10 seconds.
(this will continue until it has restarted and failed 10 times. After this is done, it will display one of the following...)
too many failures in succesion
OR
local:/root# (continuously flashes on the screen)
OR
localhost:/ I have no name!# AppleYukon- eno link active, 100-Mbit, full duplex, flow control disabled.
I really don't know what to do. I'm really frustrated with my iMac. I've had to replaced a dead hard drive within the 6 months of my purchase, and now it is acting crappy again.
Can anyone help?
Thanks.

I tried using the disk utility on the grey disks, but
they can't repair the error on my HD. I can't restore
the original software from the disks either... there
is an error when I try.
No, you can't restore while the current OS is in place, due to the fact that your 10.4.8 isn't compatible with the older version (10.4.4) that's on the install DVDs. Once a Mac OS is in place, it can only be upgraded, not downgraded. You'll have to choose either:
to "Archive & Install" which would set aside your current system unerased until the new installation is completed and your current settings are transferred over - at which point you can erase the archived OS.
to entirely erase and reformat the HDD, then install a fresh OS.
Use the install disc's version of Disk Utility to perform either. First, though, you probably need to do a PRAM reset - that often clears things up so that you won't get an error message.
To reset the PRAM:
1. Shut down the computer.
2. Locate the following four keys on the keyboard: Command (Apple logo), option, P, and R. You will need to hold these four keys down simultaneously in step 4.
3. Start up the computer.
4. Press and hold the Command-option-P-R keys. You must press this key combination after the startup chord sounds, but before the gray screen appears.
5. Hold all four keys down until the computer restarts and you hear the startup chord for the second time.
6. Release the keys.

10.6 Verbose mode stops at ACPI_SMC_PlatformPlugin::start....

Similar Messages

Maybe you are looking for