10.7.2. server - Cannot set up Virtual Domains, 10.7.2. server - Cannot set up Virtual Domains

I am rather new to Servers and DNS - but learning
I have assigned on IP on my MM Server - there I have assigned 5 different Domain names (2 already resolved - others just changed)
I started  Web service in Server App - it gave me " Default " folder -where I moved my web page files
Then I added new site in the same Server App - at first it gave me "CustomSitesDefault" Folder - that really did not resolved - so I deleted that and made speciffic "2sitename.lv" folder
Now - I have played with this quite differently - and always got some really strange results - never got what I needed.
Eventually in browser  (Safari)
- 1 site ("Default") site is working fine when I type www."1sitename".lv  - when I type without www - just 1sitename.lv - Safari displays 2site.lv
- entering 2sitename.lv - I see 1 site (Default) - but when I enter www.2site.lv - i have no result at all - it does not resolve
I have tried to erase all sites - start everything from scratch - results are similar - sometime 2 site does not resolve at all
I have all updates possible and have tried sudo stop and start webserver  - No results
Looked in the /etc/apache2 virtual host conf files - there seems everything correct - site name is directed to dedicated folder where web pages are as they should be
I just cannot figure this LION Server out ....
Please help !

A little bit of more research - it seems it is something int he binding process (most likely in the binding process we use here) that is reset wh the OS is re-inatalled.
- I used a the MBA Retail bundle to install a system on the computer.
- I bound the computer to our ad and logged in with a mobile account.
- I check for failure and confirmed it had the issue I described above.
- I reinstalled Lion over the top of the system (using the internet download model)
- The problem was gone.
but.. when I try to build an image around this, I can't reinstall the OS after the system is bound (I am working at a school and with the number of system I am using it is just not practicle)
so i did the following
- I used a the MBA Retail bundle to install a system on the computer.
- I reinstalled Lion over the top of the system (using the internet download model)
- I bound the computer to our ad and logged in with a mobile account.
- and the system failed. (the exact same as has been described above)
So I am now fairly stuck on where to go with this...

Similar Messages

  • How do I set up a virtual server with a time capsule?

    I am trying to set up a wireless camera in my house to be viewed from away from the house.
    I cannot seem to figure out port forwarding/virtual serving on the settings of my time capsule. I had no issues doing it with my old router. Does time capsule have that abilty?
    I have Macs and PCs,

    I figured it out.

  • Cannot add server to pool: OVMAPI_4004E, but hostname set to FQDN

    It's very simillar problem like thread "Cannot Add Server to Pool: OVMAPI_4010E Attempt to send command: dispatch..", but setting
    hostname with FQDN on Ora VM Manager and Ora VM Server, repairing all configuration files (using grep -R ...) and reboot OVM
    server and OVMM didn't brought any effect...
    Environment:
    Oracle VM Server version 3.2.2
    Build: 520
    Oracle VM Manager:
    Version: 3.2.2.520
    Build: 20130218_520
    Description:
    I have discovered and setup an OVM Server. Then I tried to create a new pool "ikr-pool". When I tried to attach discovered server ("srv01-xx.cssz.cz"),
    I got error attached bellow. After this actions svr01-xx stays incorrectly as "member of pool" in /etc/ovs-agent/db/server database, so I need on VM server
    to stop ovs-agent, remove file /etc/ovs-agent/db/server, start ovs-agent again, and then re-take ownership on VM server again. Then srv01-xx stays
    as "Unassigned server".
    Regards
    Vladislav Rames
    <-------------------------------------------------------------------------------------------------------------Begin of error message--------------------------------------------------------------------------->
    Job Construction Phase
    Job ID: 1364477027337
    begin()
    Appended operation 'Server Join Server Pool' to object '31:33:37:35:32:32:5a:43:32:32:35:30:30:57:44:46 (srv01-xx.cssz.cz)'.
    Appended operation 'Server Pool Construct' to object '0004fb0000020000d0b83b23645cbca2 (ikr-pool)'.
    Appended operation 'Server Pool Virtual IP Configure' to object '0004fb0000020000d0b83b23645cbca2 (ikr-pool)'.
    Appended operation 'Server Pool Member Update' to object '0004fb0000020000d0b83b23645cbca2 (ikr-pool)'.
    Appended operation 'Server Cluster Configure' to object '31:33:37:35:32:32:5a:43:32:32:35:30:30:57:44:46 (srv01-xx.cssz.cz)'.
    Appended operation 'Server Cluster Construct' to object '31:33:37:35:32:32:5a:43:32:32:35:30:30:57:44:46 (srv01-xx.cssz.cz)'.
    commit()
    Completed Step: COMMIT
    Objects and Operations
    Object (IN_USE): [Cluster] d0b83b23645cbca2
    Object (IN_USE): [Server] 31:33:37:35:32:32:5a:43:32:32:35:30:30:57:44:46 (srv01-xx.cssz.cz)
    Operation: Server Join Server Pool
    Operation: Server Cluster Configure
    Operation: Server Cluster Construct
    Object (IN_USE): [ServerPool] 0004fb0000020000d0b83b23645cbca2 (ikr-pool)
    Operation: Server Pool Construct
    Operation: Server Pool Virtual IP Configure
    Operation: Server Pool Member Update
    Job Running Phase at 2013-03-28 14:23:47,337
    Job Participants: []
    Actioner
    14:23:47,909: Starting operation 'Server Join Server Pool' on object '31:33:37:35:32:32:5a:43:32:32:35:30:30:57:44:46 (srv01-xx.cssz.cz)'
    14:23:47,914: Completed operation 'Server Join Server Pool' with direction ==> LATER
    14:23:47,920: Starting operation 'Server Pool Construct' on object '0004fb0000020000d0b83b23645cbca2 (ikr-pool)'
    14:23:47,971: Completed operation 'Server Pool Construct' with direction ==> DONE
    14:23:47,977: Starting operation 'Server Pool Virtual IP Configure' on object '0004fb0000020000d0b83b23645cbca2 (ikr-pool)'
    14:23:53,221: Completed operation 'Server Pool Virtual IP Configure' with direction ==> DONE
    14:23:53,232: Starting operation 'Server Pool Member Update' on object '0004fb0000020000d0b83b23645cbca2 (ikr-pool)'
    Job Internal Error (Operation)com.oracle.ovm.mgr.api.exception.FailedOperationException: OVMAPI_4010E Attempt to send command: dispatch to server: srv01-xx.cssz.cz failed. OVMAPI_4004E Server Failed Command: dispatch https://?uname?:[email protected]:8899/api/3 set_pool_member_ip_list [10.20.11.11], Status: org.apache.xmlrpc.XmlRpcException: I/O error while communicating with HTTP server: Connection timed out [Thu Mar 28 14:36:30 CET 2013] [Thu Mar 28 14:36:30 CET 2013]
    at com.oracle.ovm.mgr.action.ActionEngine.sendCommandToServer(ActionEngine.java:512)
    at com.oracle.ovm.mgr.action.ActionEngine.sendDispatchedServerCommand(ActionEngine.java:449)
    at com.oracle.ovm.mgr.action.ActionEngine.sendServerCommand(ActionEngine.java:383)
    at com.oracle.ovm.mgr.action.ServerPoolAction.setServerPoolMembers(ServerPoolAction.java:138)
    at com.oracle.ovm.mgr.op.virtual.ServerPoolMemberUpdate.updateMemberList(ServerPoolMemberUpdate.java:363)
    at com.oracle.ovm.mgr.op.virtual.ServerPoolMemberUpdate.action(ServerPoolMemberUpdate.java:138)
    at com.oracle.ovm.mgr.api.collectable.ManagedObjectDbImpl.executeCurrentJobOperationAction(ManagedObjectDbImpl.java:1156)
    at com.oracle.odof.core.AbstractVessel.invokeMethod(AbstractVessel.java:356)
    at com.oracle.odof.core.AbstractVessel.invokeMethod(AbstractVessel.java:333)
    at com.oracle.odof.core.storage.Transaction.invokeMethod(Transaction.java:865)
    at com.oracle.odof.core.Exchange.invokeMethod(Exchange.java:244)
    at com.oracle.ovm.mgr.api.virtual.ServerPoolProxy.executeCurrentJobOperationAction(Unknown Source)
    at com.oracle.ovm.mgr.api.job.JobEngine.operationActioner(JobEngine.java:230)
    at com.oracle.ovm.mgr.api.job.JobEngine.operationActioner(JobEngine.java:264)
    at com.oracle.ovm.mgr.api.job.JobEngine.operationActioner(JobEngine.java:264)
    at com.oracle.ovm.mgr.api.job.JobEngine.objectActioner(JobEngine.java:322)
    at com.oracle.ovm.mgr.api.job.InternalJobDbImpl.objectCommitter(InternalJobDbImpl.java:1340)
    at com.oracle.odof.core.AbstractVessel.invokeMethod(AbstractVessel.java:356)
    at com.oracle.odof.core.AbstractVessel.invokeMethod(AbstractVessel.java:333)
    at com.oracle.odof.core.BasicWork.invokeMethod(BasicWork.java:106)
    at com.oracle.odof.command.InvokeMethodCommand.process(InvokeMethodCommand.java:92)
    at com.oracle.odof.core.BasicWork.processCommand(BasicWork.java:81)
    at com.oracle.odof.core.TransactionManager.processCommand(TransactionManager.java:752)
    at com.oracle.odof.core.WorkflowManager.processCommand(WorkflowManager.java:467)
    at com.oracle.odof.core.WorkflowManager.processWork(WorkflowManager.java:525)
    at com.oracle.odof.io.AbstractClient.run(AbstractClient.java:42)
    at java.lang.Thread.run(Thread.java:662)
    Caused by: com.oracle.ovm.mgr.api.exception.IllegalOperationException: OVMAPI_4004E Server Failed Command: dispatch https://?uname?:[email protected]:8899/api/3 set_pool_member_ip_list [10.20.11.11], Status: org.apache.xmlrpc.XmlRpcException: I/O error while communicating with HTTP server: Connection timed out [Thu Mar 28 14:36:30 CET 2013]
    at com.oracle.ovm.mgr.action.ActionEngine.sendAction(ActionEngine.java:803)
    at com.oracle.ovm.mgr.action.ActionEngine.sendCommandToServer(ActionEngine.java:508)
    ... 34 more
    FailedOperationCleanup
    Starting failed operation 'Server Pool Member Update' cleanup on object 'ikr-pool'
    Complete rollback operation 'Server Pool Member Update' cleanup on object 'ikr-pool'
    Rollbacker
    14:36:31,156: Starting rollbacker...
    Executing rollback operation 'Server Pool Member Update' on object '0004fb0000020000d0b83b23645cbca2 (ikr-pool)'
    <-------------------------------------------------------------------------------------------------------------End of error message----------------------------------------------------------------------------->

    Solved. Problem was the same like in thread "I/O error while communicating with HTTP server: Connection timed out" - it wasn't accessible IP connection between Ora VM Manager and Ora VM server IP alias for server pool. But there was very confusing message in errorlog: "dispatch https://?uname?:[email protected]:8899/api/3 set_pool_member_ip_list [10.20.11.11], Status: org.apache.xmlrpc.XmlRpcException: I/O error while communicating with HTTP server: Connection timed out [Thu Mar 28 14:36:30 CET 2013]". Noticed IP address was IP address for VM server, not for VM pool, which makes me quite angry.
    Best Regards
    Vladislav Rames

  • Cannot create Virtual Directory in Windows Server 2008 R2 SP1 Environment

    Dear all,
    I am trying install Reporting Services 2005 on a Windows Server 2008 R2 SP1 Enterprise machine.
    So far we successfully did the following steps
     - Install SQL Server Reporting Services
     - Configure Service Account (Domain-User)
    After creating virtual Directory, we made several steps to avoid HTTP 400 Bad Request in Report Manager:
    1. Disable LSA Loopback in Registry and restart server
    2. Enhance Service Startup time to 60000ms and restart Server
    3. Set Application Pool to ASP.NET 2.0 Classic Mode
    4. Modify RSWebApplication.config and set These entries:
    <ReportServerUrl>http://servername/ReportServer</ReportServerUrl>
    <ReportServerVirtualDirectory></ReportServerVirtualDirectory>
    After all the Reporting Services Configuration Manager still shows a red sign and we cannot continue creating the database.
    How is it possible to solve this?
    We appreciate any help.
    Best regards,
    Mark
    Mark Kuschel
    Blog
    Xing

    Hi Mark,
    As per my understanding, we can refer to the following methods to troubleshooting the issue you occurred.
    Install SQL Server 2005 Service Pack 3.
    Deleting the newly-created virtual directory using IIS manager and then rebooting the server.
    In the Report Manager Virtual Directory dialog box, create a virtual directory for Report Manager, then change the Website to Reporting.
    Enable Apply default settings.
    The following link is for your reference:
    http://www.mathgv.com/sql2005docs/SQL2005ReportingServicesInstall.htm
    Thanks,
    Katherine Xiong
    Katherine Xiong
    TechNet Community Support

  • HT3228 I set up my work e-mail on iphone.  When I try to send an e-mail, an error code says "Cannot Send Mail", "recipient rejected by server because it does not allow relaying".  What does this mean and how do I correct it?

    I set up my work e-mail account on my iphone 4S.  When I try to send an e-mail message from my phone, an error message occurs "Cannot Send Mail" - "recipient was rejected by the server because it does not allow relaying".  What does this mean and how do I correct it?

    Get the correct mail server settings from your IT department.

  • Can Windows Server Backup spread a single backup job across multiple disks if they are not set up as a virtual disk?

    This may be a dumb question, but I can't seem to find any definitive information after having done many, many searches.  Short question is - can Windows Server Backup spread a single backup job across multiple disks if they are not in a storage
    pool or some other RAID/JBOD structure?
    Background:
    I'm running Server 2012 Essentials with all Windows Updates installed.  I have been backing up approx 2.8TB of data (Bare Metal Recovery, C:, S: (shared folders), and system reserved) for the past year+ onto a storage pool made up of two-2TB external
    USB drives.  Backup is slow (takes approx 1.5 days to complete), but generally works.  Not surprisingly I was constantly getting capacity low messages so I decided to increase my backup storage pool by adding a 3TB drive and another spare 750GB drive
    for a total of 7.75TB.  Instead of having four separate external USB enclosures, I bot a 4-bay enclosure - Startech.com model #S3540BU33E to simplify this (or so I thought!).
    The first problem I had was adding the two new drives to the existing storage pool. I think that is because the Startech uses a JMicron USB controller that reports identical uniqueid's for all drives so only one shows up in the GUI interface for creating storage
    pools. After doing research on this, I set up a new storage pool and virtual disk using all four drives via Powershell and thought I was good. However, when the backup ran, it failed after filling the first drive, saying there was no remaining capacity. In
    reality there were three remaining empty drives and there storage pool reported almost 5TB of avail capacity. I assumed this was due to the identical uniqueid issue so I decided to try a different tactic.
    Instead of using a storage pool that combines all four disks into one virtual disk, I just added each of them to Windows Server Backup as individual drives thinking it would manage them collectively. I.e., when a drive filled up during a particular backup,
    it would just start using the next drive and so on. Apparently this was a foolish assumption because the backup failed again as soon as the first disk filled up.
    So now I don't know if this is still an issue with the identical uniqueid's or if Server Backup actually can't spread a single backup across multiple individual drives that aren't in a pool or other virtual disk implementation. Hence, my original question.
    My guess is that it does *not* spread them across individual disks, but I just wanted to get confirmation.
    Thanks

    Mandy,
    Thank you for following up on my question.
    Unfortunately the article you referenced doesn't address what I am trying to accomplish.
    The article focuses on saving the same backup job to multiple disks and rotating the disks between on and offsite for enhanced protection.  However, it still requires that an individual backup job fits on a single disk.
    What I am trying to determine is if a single backup job can span across more than one physical disk (during the backup process) without those physical disks being in some type of virtual disk implementation (e.g., storage pool, RAID, etc.).
    Thanks,
    Gerry

  • (Request for:) Best practices for setting up a new Windows Server 2012 r2 Hyper-V Virtualized AD DC

    Could you please share your best practices for setting up a new Windows Server 2012 r2 Hyper-V Virtualized AD DC, that will be running on a new WinSrv 2012 r2 host server.   (This
    will be for a brand new network setup, new forest, domain, etc.)
    Specifically, your best practices regarding:
    the sizing of non virtual and virtual volumes/partitions/drives,  
    the use of sysvol, logs, & data volumes/drives on hosts & guests,
    RAID levels for the host and the guest(s),  
    IDE vs SCSI and drivers both non virtual and virtual and the booting there of,  
    disk caching settings on both host and guests.  
    Thanks so much for any information you can share.

    A bit of non essential additional info:
    We are small to midrange school district who, after close to 20 years on Novell networks, have decided to design and create a new Microsoft network and migrate all of our data and services
    over to the new infrastructure .   We are planning on rolling out 2012 r2 servers with as much Hyper-v virtualization as possible.
    During the last few weeks we have been able to find most of the information we need to undergo this project, and most of the information was pretty solid with little ambiguity, except for
    information regarding virtualizing the DCs, which as been a bit inconsistent.
    Yes, we have read all the documents that most of these posts tend point to, but found some, if not most are still are referring to performing this under Srvr 2008 r2, and haven’t really
    seen all that much on Srvr2012 r2.
    We have read these and others:
    Introduction to Active Directory Domain Services (AD DS) Virtualization (Level 100), 
    Virtualized Domain Controller Technical Reference (Level 300),
    Virtualized Domain Controller Cloning Test Guidance for Application Vendors,
    Support for using Hyper-V Replica for virtualized domain controllers.
    Again, thanks for any information, best practices, cookie cutter or otherwise that you can share.
    Chas.

  • Best practices for setting up virtual servers on Windows Server 2012 R2

    I am creating a Web server from scratch with Windows Server 2012 R2. I expect to have a host server, and then 3 virtual servers...one that runs all of the web apps as a web server, another as a Database Server, and then on for session state.  I
    expect to use Windows Server 2012 R2 for the Web Server and Database Server, but Windows 7 for the session state.
    I have an SATA2 Intel SROMBSASMR RAID card with battery back up that I am attaching a small SSD drive that I expect to use for the session state, and an IBM Server RAID M1015 SATA3 card that I am running Intel 520 Series SSD's that I expect to
    use for Web server and Database server.
    I have some questions. I am considering using the internal USB with a flash drive to boot the Host off of, and then using two small SSD's in a Raid 0 for the Web server (theory being that if something goes wrong, session state is on a different drive), and
    then 2 more for the Database server in a RAID 1 configuration.
    please feel free to poke holes in this and tell me of a better way to do it.
    I am assuming that having the host running on a slow USB drive that is internal has no effect on the virtual servers after it is booted up, and the virtual servers are booted up?
    DCSSR

    I am creating a Web server from scratch with Windows Server 2012 R2. I expect to have a host server, and then 3 virtual servers...one that runs all of the web apps as a web server, another as a Database Server, and then on for session state.  I
    expect to use Windows Server 2012 R2 for the Web Server and Database Server, but Windows 7 for the session state.
    I have an SATA2 Intel SROMBSASMR RAID card with battery back up that I am attaching a small SSD drive that I expect to use for the session state, and an IBM Server RAID M1015 SATA3 card that I am running Intel 520 Series SSD's that I expect to
    use for Web server and Database server.
    I have some questions. I am considering using the internal USB with a flash drive to boot the Host off of, and then using two small SSD's in a Raid 0 for the Web server (theory being that if something goes wrong, session state is on a different drive), and
    then 2 more for the Database server in a RAID 1 configuration.
    please feel free to poke holes in this and tell me of a better way to do it.
    I am assuming that having the host running on a slow USB drive that is internal has no effect on the virtual servers after it is booted up, and the virtual servers are booted up?
    There are two issues about RAID0:
    1) It's not as fast as people think. So with a general purpose file system like NTFS or ReFS (choice for Windows is limited) you're not going to have any great benefits as there are very low chances whole RAID stripe would be updated @ the same time (I/Os
    need to touch all SSDs in a set so 256KB+ in a real life). Web server workload is quite far away from sequential reads or writes so RAID0 is not going to shine here. Log-structures file system (or at least some FS with logging capabilities, think about ZFS
    and ZIL enabled) *will* benefit from SSDs in RAID0 properly assigned. 
    2) RAID0 is dangerous. One lost SSD would render whole RAID set useless. So unless you build a network RAID1-over-RAID0 (mirror RAID sets between multiple hosts with a virtual SAN like or synchronous replication solutions) - you'll be sitting on a time bomb.
    Not good :)
    StarWind VSAN [Virtual SAN] clusters Hyper-V without SAS, Fibre Channel, SMB 3.0 or iSCSI, uses Ethernet to mirror internally mounted SATA disks between hosts.

  • "Cannot connect to server" error when setting up MAMP local server in Dreamweaver cc 2014

    I am trying to set up my Wordpress 4.1 site with MAMP 3.0.7.3 in Dreamweaver cc 2014, but I am getting a "Cannot connect to server" error when trying to view the site live. The site works fine on the localhost:8888. I am using OS X Yosemite and PHP 5.6.2. Below are screenshots of my Dreamweaver settings. Thanks in advance.

    Hi Subhadeep!
    Think I'm getting closer (Lol). I did as you suggested and changed the web url to http://localhost:8888/Documents/projects/whoknew/. As you suggested I moved the local site to the Documents folder under the sub-folder projects. It is connecting to the server, but now I am getting the requested url cannot be found on the server. Below are screenshots of my current settings.
    http://localhost:8888/Documents/projects/whoknew/. As you suggested I moved the local site to the Documents folder under the sub-folder projects. It is connecting to the server, but now I am getting the requested url cannot be found on the server. Below are screenshots of my current settings. Thank you!

  • Cannot Reassign Virtual Desktop in Windows Server 2012 Personal Managed VDI Collection

    I have a Personal Virtual Desktop Collection on my Windows 2012 server with 3 desktops created.
    For testing purposes, I assigned the 3 desktops to admin users and everything was working well. I need to re-assign two of the three desktops to the actual end-users now that they are setup the way I want, and tested. I go through Server Manager - Remote
    Desktop Services - Collections - Virtual Desktop and select the virtual desktops, then select Assign and enter the new AD User. It does not error, and now shows the right user assigned.
    But, when I try to remote desktop for these two users, it logs into the actual Windows 2012 server, and not the virtual guest on that server.
    I've rebooted the server and guests a few times, and cannot seem to get this working for these two users.
    Any ideas?
    Tom Drought

    Here is the whole sequence of events for a "normal" connection, do you see these?
    Log Name:      Microsoft-Windows-TerminalServices-SessionBroker/Operational
    Source:        Microsoft-Windows-TerminalServices-SessionBroker
    Date:          5/14/2013 2:45:10 PM
    Event ID:      800
    Task Category: RD Connection Broker processes connection request
    Level:         Verbose
    Keywords:     
    User:          NETWORK SERVICE
    Computer:      rdvh.corp.contoso.com
    Description:
    RD Connection Broker received connection request for user CORP\user1.
    Hints in the RDP file (TSV URL) = tsv://VMResource.1.VDI-BB
    Initial Application = NULL
    Call came from Redirector Server = rdvh.corp.contoso.com
    Redirector is configured as Virtual machine redirector
    Log Name:      Microsoft-Windows-TerminalServices-SessionBroker/Operational
    Source:        Microsoft-Windows-TerminalServices-SessionBroker
    Date:          5/14/2013 2:45:11 PM
    Event ID:      801
    Task Category: RD Connection Broker processes connection request
    Level:         Verbose
    Keywords:     
    User:          NETWORK SERVICE
    Computer:      rdvh.corp.contoso.com
    Description:
    RD Connection Broker successfully processed the connection request for user CORP\user1. Redirection info:
    Target Name = VDI-BB-1
    Target IP Address = 192.168.1.108
    Target Netbios = VDI-BB-1
    Target FQDN = VDI-BB-1.corp.contoso.com
    Disconnected Session Found = 0x0
    Log Name:      Microsoft-Windows-TerminalServices-SessionBroker/Operational
    Source:        Microsoft-Windows-TerminalServices-SessionBroker
    Date:          5/14/2013 2:45:15 PM
    Event ID:      787
    Task Category: RD Connection Broker manages resource (target/session) related information
    Level:         Verbose
    Keywords:     
    User:          NETWORK SERVICE
    Computer:      rdvh.corp.contoso.com
    Description:
    Session for user CORP\user1 successfully added to RD Connection Broker's database.
    Target Name = VDI-BB-1
    Session ID = 2
    Farm Name = VDI-BB
    Don Geddes - SR Support Escalation Engineer - Remote Desktop Services - Printing and Imaging

  • Setting up Virtual Hosts on a Snow Leopard Development Server

    Hi Everybody,
    I'm losing hair over this - I thought it would be simple!
    I have set up a Mac Mini Server running SLS and would like to host multiple websites for development on the internal network. I require the websites to be stored anywhere on the server, not just in Library/WebServer/Documents/. Ideally, I would like to access them by example.com/mynewsite so I don't have to mess around with DNS.
    Currently I'm setting up websites in the Server Admin Web panel but it just doesn't work. I've noticed the error log keeps looking for files located in the Library/WebServer/Documents/ folder even though I have specified a different folder.
    What Am I missing? Does anybody know of a tutorial / guide to point out potential issues when setting up virtual hosts? I have checked Apple's guide but it doesn't really help me. Any pointers would be much appreciated!
    Cheers

    Sites is likely failing here because Sites is based on the DNS and on the HEAD command within the http stream; if the DNS does not match, you won't get to the host, and if the HEAD command doesn't match the entry in the site, then you'll either get the * wildcard or (if no *) you won't be transferred to the target Site.
    Check the web server logs, as a start.
    If you want to see how this stuff works at the protocol level, you could telnet to port 80 and toss a http 1.1 GET / command and see what you get back for a page.
    Per [rfc2616|http://tools.ietf.org/html/rfc2616], this sequence looks like this:
    +telnet www.example.com 80+
    then:
    +GET / HTTP/1.1+
    +host: www.example.com+
    followed by two presses of the return key, and where www.example.com is your target Site (virtual host) name.
    Alternatives to using DNS and virtual hosts are port-based hosting (which is easy), and you can also use IP addresses to establish virtual hosts. The former is set up via the Sites stuff, with various other ports being used for the web servers. Ugly, but easy. The IP-based approach can get ugly fast, too.
    If you get DNS going and aliases added, and all this goes away in a puff of greasy orange smoke.

  • I am trying to set up a mail account but I get a warning that my password cannot be sent securely to the server.  how do I correct the problem?

    I am trying to set up a mail account but I get a warning that my password cannot be sent securely to the server.  How do I correct this so that I can set up my email account?

    1. If you haven't tried this already, just delete the user account entirely, and then try setting it up again.
    2. To find the permissions file:
         a. hold down the option key
         b. go to the Go menu in the finder
         c. scroll down to Library and open it
         d. in Library, go to Containers/com.apple.mail/Data/Library/Preferences
         e. drag it to the trash and restart.
    3. if that doesn't work, go to Applications/Utilities/Keychain Access. In the Keychain Access menu, do Keychain First Aid, and repair.
    This should keep you busy for a while.

  • I am trying to set up virtual servers with Netscape Enterprise Server 3.6. Can get home page to display but images linked to the page won't display and links to other pages won't work.

     

    hi,
    If your home page of the virtual server is displayed then,you have set the virtual server properly.
    check the links and source of the images or directories in the HTML source code of the home page.
    this should solve ur problem. If not notify me.
    Regards
    T.Raghulan.
    [email protected]

  • Getting error message setting up contacts "your setup cannot start because the iCloud server has stopped responding"   How can I fix this?

    Trying to set up contacts on Windows7 PC. Get error message that "setup cannot start because iCloud server has stopped responding.  How can I fix this?

    Looks like itunes was still trying to communicate with my iphone and got confused when it couldnt find it.    Found this in another post and it worked great.
    Solution:
    Make sure you are not connected to the internet and then open itunes. Sync your phone and then enable the internet again. Then stay connected to the internet and close your itunes and reopen it. Bam problem solved.
    By WaKaDo

  • Set value when a virtual, analog modem should answers in Server 2012 Routing and Remote Access

    Hi there,
    I googled for hours on the following problem:
    We have a Routing and Remote Access Server with an Dialogic Diva PRI card (30 lines). The card provides an analog, virtual modem pool. All this runs on Windows Server 2012 (without R2).
    My problem is that the client will be connected after 3 or 4 rings on the line (I can not hear properly with our client device), but it should be connected after the first ring.
    Under Server 2000 there was the possibility to set the value "NumberOfRings" in the registry and / or  set the modem to ATS0 = 1. Both ways do not work in Server 2012.
    Can anyone tell me how it works under 2012?
    Thanks and regards
    Andre

    I assume you followed Dialogic's instructions for configuring the device on Windows Server 2012.  It would most likely make more sense to contact Dialogic if you are having issues.  They support the product.  If it is not working according
    to their configuration instructions, they are in the best position to be able to answer your questions.
    . : | : . : | : . tim

Maybe you are looking for

  • Mapping the R/3 Fields with InfoObjects

    Hi Guru's,                I am working on CO-PA Datasource, i have the r/3 fields from which i have to map the info objects in BI. I found all the relevent infoobjects, but few left without mapping.I tried to find these fields from tcode:se11/rsosfie

  • How to add a new database service name to 9iDS

    Hello, I installed 9iDS and 9iDB on my laptop which worked fine for few months. I had trouble with 9iDB I/O system so I reinstalled 9iDB with a new SID name. I updated 9iDS by replacing old SID name with new SID name in tnsnames.ora file but it did n

  • I need help re Adobe Pro 9 and Adobe Xi Standard

    I recently bought a Fujitsu Scan Snap for my home office.  I installed the Scan snap with no issues.  Unfortunately, there are no real instruction with regard to the software end of the installation process.  The scanner came with additional software

  • MSI NF735GTX-P31 display delayed 20-30 minutes after cpu power on

    I have a problem with my PC: Motherboard - MSI NF735GTX-P31 RAM - 3gb When I pressed power on button, CPU beep fine, but no bios/just black, only can see CPU red light blinking, the display showed after 20-30 minutes. I have try to reset CMOS, reseat

  • Strange error when adding a column

    I am trying to run the following SQL but get this error: ALTER TABLE s1_grainsmart_option     ADD ppv_flag                   char(1)       DEFAULT 'N'   not null         CONSTRAINT ckc_gso_ppv_flag CHECK (ppv_flag IN ('Y','N')) ERROR:  a problem occu