10.8.3 on mini memory issues

Since updating my 4GB late 2009 mini its functionality reduced to almost zero. PhotoShop and Dreamweaver both crash. Once crashed the machine must be restarted but will not restart and have to disconnect power to recycle. Apps then work only if they are the only thing running.

Apple requires 2GB of memory to run Mountain Lion, before any application demands. If you would use and keep a current profile, we wouldn't need to inquire about the current installed memory, and if it were sufficient to support concurrent large memory footprint applications such as PhotoShop, Dreamweaver, and more.
All three of the late 2009 mini models can (unofficially) support 8GB of memory. They all came with a GeForce 9400M discrete graphics with 256MB VRAM. The latest PhotoShop CS6 requires a minimum of 256MB, and recommends 512MB VRAM. It wants a minimum of 1GB of system memory. Dreamweaver wants 512MB minimum memory and Java 1.6 installed. Adobe also considers compatibility of their CS5, CS5.5, CS6 suites with Mountain Lion to require latest Flash player updates.
Memory demands not-withstanding, I would start with the following steps to clean up your filesystem:
Disk UtilityBoot drive
Verify/Repair permissions
Verify drive itself
Local CacheMove the contents of ~/Library/Caches to Trash
Safe Boot Mode
Boot, press and hold shift key (at the chime)
Release shift key when horizontal progress bar appears
After you login, empty the Trash
Reboot normally
Purge PhotoShop cache
By now, you should sense improved interactive filesystem response. The next issue is whether the PhotoShop and Dreamweaver versions that you have are actually supported for use with Mountain Lion. They may need updating for 10.8.3. If you have Java 1.7 installed now, and Dreamweaver attempts to reference a 1.6 feature, that may not bode well for your system stability either.

Similar Messages

Ipod mini memory issue

My Ipod mini randomly loses songs from its memory if I don't use it for at least a week. And the screen is starting to get glitchy, too. What do I do????
Windows XP

Usually Apple doesn't actually replace the battery, but instead places it with an exact model. So yes, your data will be lost, so be sure to back it up to your computer if at all possible before sending it in for repairs/replacement.
B-rock

N97 mini memory issues

hi!
i got n97 mini.
i had some probs with it so i started saving apps from ovi on my memory card and my msgs on the mass memory so if my n97 need to be reset i wont lose too much data.
now i got two probs ,
1. i installed couple of programs from ovi, and they worked for a while and now when i click on them it doesnt do anything, i tried to uninstall them but they dont apear on my installion apps, so i tried to download again from ovi but it doesnt let me download what i already downloaded , i even formatted my memory card , now all the apps icons removed but still i cant download from ovi.
2. the msgs on the mass memory works but once in a while when i receive or send an sms i get an error msg which tells me that now it will use the phone memory, andi need to go to settings again and chage it to mass memory and the msg i had just sent is saved on the phone memory and not on the mass memory.
thank for any help you can give me!!!

Hi, for message storage, it's a tait of Nokia phones, thet after connection by usb that the storage point will revert to C, so when I disconnect my phone from computer I always check it's still set to E.
As for apps, there are loads of sources other than Ovi, try Getjar .com, you can download to computer and just drag and drop.
As for ovi store, I don't use the app, I simplyuse web browser to go there (it keeps trying to make you install ovi store but ignore it, just select exit.) find the app you want log in and download.
Hope this helps
Good Luck
PS you can remove apps by selecting organise in the apps folder, tap/highlite the app you want to remove and select option-remove
If I have helped at all, a click on the White Star is always appreciated :
you can also help others by marking 'accept as solution'

Question for those with memory issues on k8n neo plat

I have been having issues with my memory on the k8n neo platinum board since i built the system last month and i just recently discovered a fact I had overlooked.
I Have discovered that if i test the system while it is cool (having sat turned off overnight for example), then memtest will pass the ram just fine and the system will be stable for a short period of time, generally longer if no intensive applications are used, ie. doom3 vs. websurfing).
This system, once it heats up ( seems mostly to be the nvidia 3 nb that needs to be "hot"- that is, a probe placed in contact with the module reaches about 58+ degrees c) then the system becomes unstable and memtest, if used, fails.
Prime95, if used on it when its cool, will usually take about an hour or so to fail, but if its used on the system when its been running a bit ( temps from nb at 58c+ and memory module hot to the touch) then it fails after about 20-30 seconds.
I have placed an active hs on the nb in an attempt to correct this, but temps still remain high with failures occuring.
I have spent the better part of three days testing the sytem this way and the above facts have held true in all these tests.
I have tested at stock ratings ( not using "auto" in bios, but using "approved ratings" of 10 x 200 for fsb and timings of 2-3-3-7 for my ram at 1:1 (which is recommended as well) since i am testing for base stability at this point;Voltages have been left at auto settings, however.
I was wondering if anyone else with memory issues could try this out and post if this seems to be the case for you as well.
Perhaps the memory issues on these boards are directly related to a problem with the nvidia 3 chipset running too hot?
Does anyone have a memory issue with these boards who is using water cooling on the NB ?
Lack of issues from people using 'problem" memory, but having no failures with water cooled nb's would support my assumption.

Yes i did mean chipset.
I am using a stock hs/fan from amd, which seems to run a tad hot but, considering that I wont overclock until I can get board stable, its not an issue. (runs 35-40 idle and up to 72 intensive). I need the warranty more then the extra mhz at present.
I removed the stock heatsink from the nvidia chipset and bought a generic chipset cooler (green, very little in the way of fins and seems to be aluminum) with a small fan.
I used a generic silver paste from Compusa to adhere both the cpu hs and the chipset.
I didnt lap either hs, just installed each as per instructions on artic silvers website (figured it had to go on the same way even generic).
I also bought a kingwin thermal center which i ran probes from to the cpu, case, and nb chipset.
I am not using it to adjust fans so those arent connected - its just a reference temp I can see at a glance, esp considering the funky bios reading this boards been known to give.
I assume from these responces that even a nvidia 3 250 chipset shouldnt get as hot as mine?
I asked about that from the retailer i bought this from but he seemed to think it was "ok" at 50ish celcius, but then again he didnt look too confident when he said it, lol.
Idle right now reads on Corecenter at 28 celcius for cpu and 33 celcius for the chipset, although, I have readings of 37 c and 43 c from the kingwin thermal center, which i believe to be more accurate.
My voltage reads at 11.67 for the 12v line at idle right now.
The psu i got is stick from the xblade case i bought in store. (http://www.xoxide.com/xblade2.html)
I have a dvd burner, cd drive, and two maxtor ide hd's attached to the system;The only card is the agp.
Is there a way to check and see if the cpu ispower starved? software monitor or even an external probe perhaps?
I havent put a probe on it, but the ram came in its own heatspreader, which gets very hot to the touch as well.
What temps should I be looking for on these items?

N97 mini software issues

It has been a week since I purchased a new N97 mini and I had to restart it almost 20 times since then.
Here are the issues I see with this phone, Iam not sure if it is software/hardware/memory issue:
1. After downloading music from nokia music store, music player doesnot respond to the refresh music library and if you persistent in forcing it to refresh, phone freezes and you will have to literally take the battery out. The issue when I looked at a little more in this case is, whenever music files are stored in anyother directory then Music in the Mass memory, software has issues in refreshing library.
2. To come around the above issue I downloaded music to my PC and stored in Music directory in Mass memory, now there is second issue that came up.....This time it refreshes fine, but when switching between two albums in the library phone freezes again, and being persistent again in this case will make the phone freeze to the worst possible extent where in you will not be able to receive any phone calls and you will have to remove the battery and restart it.
3. To come around the above two, I started playing music from file manager by opening the file, and bingo there is a problem here as well, file manager freezes to death....
I didnot approach Nokia service yet, and am exploring if there is a solution to the above mentioned issues.....
In case you have faced similar issues and found a solution, plz help me, so that I dont have to take my brand new phone to the service centre.....
Pradeep

Hi, firstly I only ever drag and dop mp3 music onto my hard drive and usually fine, did have a refresh problem after update recently and did this (may help you) also if you;ve downloaded a lot of data lately, try cearing privacy data on phones web browser , you may have used a lot of RAM which could cause phone to slow down or freeze.
/t5/Nseries-Devices-and-S60/N97-music-player-problem/m-p/619717/highlight/true#M191075
Hope this helps
Good Luck
If I have helped at all, a click on the White Star is always appreciated :
you can also help others by marking 'accept as solution'

Low memory issue

I have an HP Pavilion 2 Quad Proc 2.5 Ghz. Vista 32 bit home prem, 4 GB DDR2, 512 MB Nvidia 8500GT, Realtek Audio (updated driver), Blu ray read/write drive, Two 500 GB interinal drives 7200rpm SATA 3GB, Virtual mem set to windows control. Program PE7
I shoot video on a Canon SX1 IS. in 1920 x 1080 30f/s h264 MOV files. If I edit less than 4 Min of Video in PE7 all is well. 5 min of video causes low mem warning from PE7. No message from Windows. Adobe tech support said it is a windows virtual memory issue talk to Microsoft, but nothing else. I have HP support but they said it is outside the scope of support. For $ 60 I can get better support one time but no guarantee. I tried Reg cleaners, manual setting virtual mem at 18 GB. That helped a little. Rebooting helps., but in the end I get "program not responding" or other failure messages. I have read other posts but they were talking 40 min of video or more. I have had no problems with video from my old Sony I have edited over 1 1/2 hr. but 5 min of DH video brings it to a halt.Is anybody editing from this model Canon with sucess? I can play video from the camera with HDMI cable and it is beautiful. Any ideas?
Richard

Steve
I can understand how it would help process time but helping memory is a strange concept. Since less compression means bigger files. Memory management is way beyond my understanding. I have been working with computers since the PET and TRS80 with 2 kb upgrade and I want to use a hammer some days. I feel Adobe has a way to go with Memory management so that we can just open the program and edit video. I can understand taking a long time to process data in virtual memory but why the "program stopped" message? It is as if virtual memory is not used. Also data not used at the moment could be sent to the disk. It would be a lot slower but no memory crash. I can remember running large databases on 8 bit machines with 64 kb of memory. Of course a large database was smaller than one or two sec of video.
Thanks for the reply
Richard

Rendering and Low System Memory issues in PE9.

Hello again.
N.B: I am an ex-PE3 user.
I am having a few issues with PE9.
1. My main issue is that I am regularly getting the 'low system memory; please proceed with caution' message. I have googled it and read people's suggestions, but am not sure where to go from here. I have tried saving my file under another name, but am already up to '....E' (fifth) version of the file I've been working on this afternoon. The total time of the project is only approx 45 min's, although I will say that this 'low system memory' issue seems to be worst today, as I'm adding more still photos.
2. One of the suggestions made by Steve G on one of the forums was to make sure projects are regularly rendered. When I hit 'Enter' to render, the little render window pops up for a split second and then disappears. And I would assume from the red line above my timeline that my file is not rendered.
3. When I switch to 'Sceneline' view, my horizontal scroll-bar across the bottom will only drag SO far (to a certain point in my project; but definitely not to the end of my project. It is really frustrating. I sometimes can fix it by flicking between Sceneline and Timeline, but I have to do this multiple times... and it seems a ridiculous way to do it.
It would be fantastic if someone could help me with these issues, please!
System details:
AMD processor 3.2 Ghz
4 gig RAM (3.12 gig usable)
Windows 7 Ultimate

Hi everyone:
Thankyou for all your suggestions.
Sorry, Bill, but both those links give me an error message. I was all set to read them, but they won’t work, unfortunately.
What is meant by ‘page file managed’, sorry? And do you mean ‘hard disk drives’ by HDD, or does it stand for something else in this context? I’m not sure what you mean by how do I have them allocated. Again, apologies for my ignorance. I do have only one HDD, but it is partitioned.
The image sizes all seem to have a depth of 24, but vary in dimensions – I can see that some are quite large (around 3 mg in size, with dimensions of 4288x2848, for example). Is the actual mg-size relevant, or only the physical length and width?
I have tried to look at the frame size of my project, but it seems to be greyed out. In pale digits, there is 720x576 written.
Just before I sent this, I thought of one other thing to try first.
I tried starting a ‘New Project’. I then inserted just 6 still photos, for experimentation purposes. I then hit ‘Enter’ and the Rendering window came up and appears to have rendered correctly. So I then tried looking at one of my other projects (that hadn’t previously been rendered) and tried to render it. In this case, as in for the project I am currently working hard on, the Rendering window flashes up for about ¼ of a second and then disappears.
What is going on???
From: Bill Hunt [email protected]
Sent: Friday, 11 March 2011 2:00 AM
To: rachel jewiss
Subject: Rendering and Low System Memory issues in PE9.
although I will say that this 'low system memory' issue seems to be worst today, as I'm adding more still photos.
What are the pixel x pixel dimensions of those still images?
What is the Frame Size of your Project?
How is your Page File Managed, and what is the size? This http://forums.adobe.com/thread/632449?tstart=30 will give you some background and tips.
Also, tell us about your HDD's, and how you have them allocated.
For more discussion on Rendering, please see this http://forums.adobe.com/thread/794719?tstart=0.
Good luck,
Hunt

Hyper-V 2012 R2 - live migration dynamic memory issue

Hi..
we use a two node hyper-v cluster.
On each node running 5 vm that shared the 64GB system memory.
The vms are configured to use dynamic memory. The sum of the startup (min) memory of the 10 vms are currently 50 GB.
So now our problem:
If we try to drain roles on node A for maintenance purpose two vms are still on node A because they wasted currently each 25GB memory and so on node B is not enough free memory to host this vms.
That sounds logical
But as all vms configured to use dynamic memory they should shrink their memory to get enough space for all vms? If we shutdown all vms, move it to one node, then everything works fine.
Is it by design that live migration do not trigger the vm to shrink their memory?
Best regards, Alexander Zirbes

Hi Alexander,
Dynamic memory means that memory can increase or decrease based on the demand of the VM, not based on the load of the Hyper-V host. If the gust OS of VM dont need that much memory, memory will be released. I dont think live migration has any role shrinking
the allocated memory of a VM.
Since you are using two node cluster, you should only load 50% resourses on each host so that incase of a failure of second node, the first node can have all the VMs.
This calculation will become more effective if you have more nodes. I am having a six node cluster and I load each host upto 80% so that in case of a single node failure, the VMs can be split on other five nodes without issues.
Cheers,
Shaba
Optimism is the faith that leads to achievement. Nothing can be done without hope and confidence.
InsideVirtualization.com

Coldfusion Multi instance Memory Issues

Hello, we recently got brand new servers with 8gb of ram and 64bit Windows 2008. We have about 7 instances created on these servers and I am noticing something extremely disturbing. On 2 of the instances which I just created today that have absolutely no sites running on them yet as we are still migrating sites. Coldfusion immediately consumes 700 to 900 mb of working set memory. this is for all instances which then makes my server seem like it is out of memory. on the old box it only took the about of working memory that is needed and this would grow over time but not immediately upon starting the server. I started on of these instances and litterally watched as it took 850mb of ram within 2 minutes of starting and it doesn't get released.
I do have the jvm set to 2gb and they do for now all share the same jvm. I am just curious if anyone else running 64bit Windows 2008 is having the same issue and if it is just normal behavior with 64bit systems. We moved to these beefy servers to help with memory issues but it seems I am still plauged with the issue even when there is no site allocated to the instance.
Any ideas and thoughts would be appreciated.
thank you.

If you have a min memory parameter in your jvm.config (-xmxMin or somethingn like that, then each instance on start will immediately reserve that amount of memory.
This is a java thing not CF. With CF8, I don't think having the min memory value matters with the most recent java versions. I previous versions you would occasionally get out of memory errors if you didn't, but I haven't heard of this since CF8 came out.
They may have also fixed something in 8 to help alleviate that issue.
So chaulk it up as normal. With 7 instances you'll probably run into more CPU issues.
Byron Mann
[email protected]
[email protected]
Software Architect
hosting.com | hostmysite.com
http://www.hostmysite.com/?utm_source=bb

Application is not working due to memory issue

Hi Friesnds,
Kindly help me regarding settings in java. Scenario is like that. I have one server having two jboss versions (jboss-4.2.3 GA and jboss- 3.2.6). Each having java memory (JVM settings) 1 GB. The total memory of that server is 3 GB.
Problem is that every two days my application is not working due to memory issue. Once i freed the memory (through run the commands - (1). sync
(2). echo 3 > /proc/sys/vm/drop_caches
Application works fine.
I heared that the above command (echo 3 > /proc/sys/vm/drop_caches) can't run frequently because of server crash.
Kindly help me regarding this issue and provide the resolution.
Let me know if you need more information from my side.
Thanks
Ashish Shukla

All of the above. I tested on 4 different networks and had no luck, I also had friends test my network and the other networks with their iPhones and all had no issues using FaceTime.
Also after I wiped my phone (erased all content and settings) I was able to successfully initiate a FaceTime call with no changes to my network and was also able to initiate another call when connected to another previously tested network that didn't work before. Once I restored from backup though, FaceTime stopped working again.
I did find this discussion: https://discussions.apple.com/thread/5163024?start=0&tstart=0
and tried the suggestions found there too. That discussion describes my issue I am having as well.

How to correct internal memory issue

This is related to the standard SAP program SAPRCKM_MR11 in which there is one include RCKM_MR11F01 which contains a select statement :
SELECT *
     INTO CORRESPONDING FIELDS OF TABLE t_bhistory
     FROM v_ckmlgrir
     WHERE bukrs EQ p_bukrs
     AND   ebeln IN r_ebeln
     AND   ebelp IN r_ebelp
     AND   lifnr IN r_lifnr
     AND   ekorg IN r_ekorg
     AND   ekgrp IN r_ekgrp
     AND   werks IN r_werks
     AND   bedat IN r_bedat
     AND   bsart IN r_bsart
     AND   bstyp IN ht_bstyp
     AND   vgabe IN ('1', '2', '3') "Wareneingang/Rechnung/Nachbel.
     AND   loekz_k NE 'L'            "Loeschkz. Bestellkopf
     AND   loekz_p NOT IN ('L', 'S') "Loeschkz. Bestellposition
     AND ( frgrl   EQ space          "Freigabe unvollständig
     OR    frgrl   IS NULL )
     AND ( memory EQ space          "Bestellung noch nicht komplett
     OR    memory IS NULL )         "falls Feld nicht initialisiert
     AND ( xwoff   EQ space          "Wertbildung offen
     OR    xwoff   IS NULL )         "falls Feld nicht initialisiert
bei Dienstleistungsbestellungen werden mehrfach kontierte
Bestell-Pos. gegen das WE/RE-Konto gebucht, deshalb dürfen
mehrfach kontierte Pos. nicht generell überlesen werden.
      AND   vrtkz   EQ space          "keine Mehrfachkontierung
     AND   wepos   EQ 'X'            "Wareneingang wird erwartet
     AND   repos   EQ 'X'            "Rechnung wird erwartet
     AND   weunb   EQ space          "Wareneingang unbewertet
     AND   stapo   EQ space.         "Item is not statistical
There is one job FMT612P which contains this standard program and the job is going to abend
because of the select statement given above which is because of some memory issue with the internal table t_bhistory, please give us a suggestion how we can avoid the same.

Hi,
I am also facing the same issue. We had copied this report into a custom report and are trying to improve performance by breaking the view into separate queries on EKKO, EKPO and EKBE.
Can someone advise the best way to deal with this view v_ckmlgrir or a best approach to break down the view into separate queries.
Thanks
Edited by: Shreyas Shrikant Kulkarni on Jun 29, 2009 4:56 PM

Memory issue with Podcast !!!

Hi,
I have several issues with the Podcast App.
- i cannot sync podcast that i have downloaded on my laptop using itunes to the iphone,
- when i download some podcast directly on the iphone, i cannot play them, i still have to stream them,
- i have uge memory issues and i think that the downloaded version of the podcast might be somewhere on the iphone, but cannot access / delete them (over 16 GO, i have more than 4.5 GO used for 'other', that are not related to anything...)
i have tried to delete / reinstall the app, but this does not change anything...
Any help ?
Rgds

Quote
I have a MSI 975X Platinum rev 2 mb with a e6300 processor overclocked to 2.24ghz.
If your CPU operates @2.24 GHz, it means that you increased FSB frequency to about 348 MHz.
To make sure there is no misunderstanding here, let me point out the following:
Memory frequency is ALWAYS linked to FSB frequency by the FSB/DRAM Ratio you can select in BIOS. If you select 1:1 for example, the BIOS will show that memory frequency is 533 MHz. This value however, only applies to the default FSB clock speed of 266 MHz:
266 MHz x 1 = 266 MHz (or 533 MHz effective DDR2-frequency).
If your system is overclocked, what counts is only FSB/DRAM ratio, not the memory speed displayed in BIOS. That means, if you set FSB/DRAM ration to 1:1 and FSB frequency to 348 MHz, your RAM will operate @:
348 MHz x 1 = 348 MHz (or 696 MHz effective DDR2-frequency).
The main question is:
What are you talking about when you say, you can't make your RAM operate @800 MHz?
The BIOS does not offer a proper divider to get your RAM to 800 MHz @348 FSB clock speed to begin with.
You have the following choices if your overclock your system:
FSB=300 + FSB/DRAM ratio = 1.33
300 MHz x 1.33 ~ 400 MHz (or 800 MHz effective DDR2-frequency)
FSB=320 MHz + FSB/DRAM ratio = 1:1.25
320 MHz x 1.25 = 400 MHz (or 800 MHz effective DDR2-frequency)
FSB=400 MHz + FSB/DRAM ratio = 1:1
400 MHz x 1 = 400 MHz (or 800 MHz effective DDR2-frequency)
Use CPU-Z to monitor the DRAM frequency that is actually set if you are overclocking.

Memory issues

I have a 2008 Macpro...remarkable up-to -date for its age...I plan to use it for some time yet. Lately I have been a having what seems to be a memory issue. There are 12 gig of Ram installed...6x2 gig each in pairs. Sometimes on boot the screen only shows a flashing folder. I shut down and reboot, and it seems fine...but only 8gig of ram shows installed. I opened it up, unseated the boards that hod the ram, and unseated and reset all he ram, and replaced the boards. Great, all he ram shows, 12 gig again. This morning, a few days later, it did it again, showing 8. So, when I run Crucial's memory analyzer, it shows first four slots full, last four empty. A few questions...are the first four slots the top board, the last four the bottom board? This, BTW, is what it was also showing before I reseated the ram. If so, the ram in question s on a separate board. Opinions, is the ram bad, or the board, or neither? Should I reseat again and flush with contact/tuner cleaner/degreaser? Could this hurt? (it is made to clean electronics) the machine does seem ever so slightly unstable. FCP crashed once in a 5 hour edit, which it has done before but rarely. The machine itself did not crash, just the program. Can using the machine like this do more damage, or will it just not boot? I feel it is a seating or connection issue, as I have never seen ram come and go, once it is fried it's fried. The ram is still pretty pricy, but I was going to buy 4 more gigs just to fill it out. Are the two board that hold the ram identical, top and bottom? If so, is a good diagnostic tool to swap them and see what happens? Move all the ram and swap board positions, or do I risk blowing ram ? Remember, the ram did show up when I reseated, so it seems like it is I damaged. My goal would be to see if top ram stops appearing. Does ram need to be filled in order? I know in pairs, but can I just swap the boards and leave the ram, which should look like filling slots 1,2,5,6,7,8...as opposed to 1,2,3,4,5,6. Can the boards be swapped, or are they set somehow to be 1-4 and 5-8, or is that determined automatically by their upper or lower insertion? Any other advice is appreciated. Funds are low, so I need to keep this machine running. Other info, 3.06ghz (2 quad core) Xeon CPUs, 1tb system drive, 4 TB raid5' OSX 10.6.8 dual graphics display with 512MB (can't remember card model right now). Also, can I update graphic card in this machine? I looked at it a few years ago, but the I for I found was confusing and I never got to it. I figure I might be able to get a better card pretty cheap by now. Thanks all.

You have typed a huge list of ideas all as one paragraph with many questions in it without a single bit of white space. My eyes are not good enough to read a question, attempt to answer it, then dig through the sea of letters to find the next question.
Your writing needs white space, which gives it a peculiar overall shape, and allows a reader with poor eyesight to return to a particular spot in the text. So I will attempt to answer some parts of your query, but will be forced to do so from memory of what you wrote.
The Mac Pro uses Error Correcting Code (ECC) RAM. Eight extra bits are stored with each word, and checked when read back. Single-bit errors are detected, and the check bits are used to make a correction on the fly. More complicated errors are detected, and can cause your Mac to halt on a kernel panic to prevent bad data from propagating.
ECC RAM means your Mac can detect bad memory easily at Startup, and can declare pairs of DIMMs "absent" to avoid using them.
Contact corrosion, which was an issue with much older DIMMs, is rarely an issue with these FBDIMMs. Once re-Inserted ONCE, corrosion will not recur for a year or more.
The upper and lower Riser-cards are identical.
The FBDIMMs in these machines are subject to overheating and death. If Mac OS X or any program reports DIMMs as missing, at least one of the DIMMs in that pair has died (but since they are installed in pairs, both are marked absent).

Firefox 3.6.8 and memory issues

After the last update to 3.6.6, I disabled plugin-container per the instructions given on the forum, and my RAM problems went away. However, after the automatic update to 3.6.8, the memory problems came back, with memory usage going up to 92%. I downgraded to 3.6.4, and turned plugin-container off again; while memory usage is currently at 84%, it is not as low as it was before the upgrade to 3.6.8. (79-80%) (There is very little difference in the websites being opened on the various tabs.)
== This happened ==
Every time Firefox opened
== I upgraded to 3.6.8

ffs guys. It's a free browser. It's cool. We love it. But can we do something about memory issues? Almost every release has huge memory leaks.
How about halving the release points and focus on memory issues for the other half of the time. I am a long time user since way back in the day and it seems to me that instead of trying to release so many versions, we should be focused more fixing the current release.
I say put a moratorium on new features until bloat can be fixed. These experiences are starting to give me a hardon for IE again.
Screw new features. I can deal with plain old tabs like they are. I don't need more bells and whistles. This browser has been kicking ass and taking names for a loonnnggggg time. We don't need more bloat. Keep the security fixes coming but everything else can wait. Take a breath. Stop and smell the roses for a few weeks.

Regarding Memory issues((error) while scheduling the job

Hi Friends
I am facing memory issue while rerunning BODS jobs in production.As we have rapid mart when jobs got failed i rerun the
job suddenly job got failed and in logs i found Memory issue
please help me what i have to do in steps
Thanks

I think there is no one solution to buffer pool issue. Buffer pool issue happens due to many reasons like how you design the data flow, requirement of push down or even insufficient memory in the running environment.
You can check by checking 'collect statistics for optimization' during running the job. Also in the data flow, try changing from pageable cache to memory cache by right clicking and selecting properties. The below link give some details on caching, might be helpful.
https://wiki.sdn.sap.com/wiki/display/BOBJ/CachinginDI
Arun

10.8.3 on mini memory issues

Similar Messages

Maybe you are looking for