10.8: Copying wikis over from an unbootable image
My server's hard disk became corrupt and was no longer bootable, nor repairable to the point where it's bootable. I have a complete disk image of the unbootable volume. I also have a bootable image of that same server but it's a few months old and I would prefer to have the more up-to-date information.
I have a fresh installation of server up and running pointing to the same open directory server, i.e. the same users.
Assume that no data in the hosted wikis got corrupted. Can I copy a folder from the unbootable volume to the same place in the new server and have my wiki data back again ? If so, which folder ?
I will, of course, do this when not booted using that volume, so I won't be replacing files while the wiki system is running.
Most of the 10.8 Server content is stored in /Library/Server. Copying that to the new system should go a long way towards getting you back up and running.
Similar Messages
-
10.8: Copying calendars over from an unbootable image
My server's hard disk became corrupt and was no longer bootable, nor repairable to the point where it's bootable. I have a complete disk image of the unbootable volume. I also have a bootable image of that same server but it's a few months old and I would prefer to have the more up-to-date information.
I have a fresh installation of server up and running pointing to the same open directory server, i.e. the same users.
Assume that no data in the hosted calendars got corrupted. Can I copy a folder from the unbootable volume to the same place in the new server and have my calendar data back again ? If so, which folder ?
I will, of course, do this when not booted using that volume, so I won't be replacing files while the calendar system is running.Most of the 10.8 Server content is stored in /Library/Server. Copying that to the new system should go a long way towards getting you back up and running.
-
Can't see photos copied over from old mac - any ideas?
I copied my photo library over from my old mac (same method as I used for my iTunes library, which worked) to my new one. I just dragged out the original empty library folder and put the one from the old mac in its place. Non of the photos showed up.
I figured I would deal with it later and have since added photos from my camera. I am now trying to see the older photos but no luck. My photo library, seen from within iPhoto, has albums for the years listed but without the pictures.
I did the rebuild but that didn't change anything. I tried importing them but iPhoto tells my I can't import them since they are already in the library.
Anyone know how to solve this?
Thanks,
DavidDo you still have a copy of your original library from the old Mac?
If so try the following:
1 - copy it again to the Pictures folder.
2 - download and run BatChmod on the iPhoto Library folder with the settings shown here, putting your administartive name in the owner and group sections. You can either type in the path to the folder or just drag the folder into that field.
3 - launch iPhoto with the Option key depressed and select that library folder to open.
Now see if the album gets converted correctly. You can move your other iPhoto library folders to the desktop temporarily until you see if this procedure is any more successful.
Also update to 10.4.9 with the COMBO updater and update Quicktime to the latest version, 7.1.5. Of course repair disk permissions afterward with Disk Utility.
Do you Twango?
TIP: For insurance against the iPhoto database corruption that many users have experienced I recommend making a backup copy of the Library6.iPhoto database file and keep it current. If problems crop up where iPhoto suddenly can't see any photos or thinks there are no photos in the library, replacing the working Library6.iPhoto file with the backup will often get the library back. By keeping it current I mean backup after each import and/or any serious editing or work on books, slideshows, calendars, cards, etc. That insures that if a problem pops up and you do need to replace the database file, you'll retain all those efforts. It doesn't take long to make the backup and it's good insurance.
I've written an Automator workflow application (requires Tiger), iPhoto dB File Backup, that will copy the selected Library6.iPhoto file from your iPhoto Library folder to the Pictures folder, replacing any previous version of it. You can download it at Toad's Cellar. Be sure to read the Read Me pdf file. -
Can't copy some files from Windows 7 to Mac OSX over network
Hi,
I'm running the latest version of Max OSX v10.8.4 on a brand new Macbook Pro.
I have followed the setup instructions at http://www.7tutorials.com/how-change-workgroup-mac-os-x-easy-networking to access my Macbook from Windows, and http://www.howtogeek.com/howto/24950/how-to-share-a-folder-in-os-x-with-windows/ to share some folders from my Macbook to Windows.
I am now trying to copy some files from my Windows 7 Pro (SP1) computer to my Mac, and have hit the following problems:
I can view my Macbook in my list of local networked computers on WIndows, but I cannot access it. Clicking on it causes Windows 7 to try and access it, but then I get a message after a minute saying the network path could not be found. However, if I manually enter the IP address of my Macbook in the Windows address bar (\\192.168.0.191), I can view and access all the shared folders. I can never access the Macbook via it's computer name (\\MACBOOK-ROB).
I cannot copy some files from Windows to my Macbook shared folders via Windows. There is nothing to distinguish these files from the hundereds of other files that I have successfully copied to my Macbook. They are pictures and music with no special characters in the filenames, not overly long filenames or folder paths, no access restrictions, or any other security restriction that I can see. However, every single attempt to copy these files to my Macbook results in WIndows reporting that access to the destination was denied.
I have tried both these above scenarios on WiFi and Ethernet, and the results are the same.
So:
Why am I unable to access my Macbook by it's computer name on the network? How can Windows see it, but not access it?
What are the limitations on transferring files over SMB that is (presumably) causing these specific files to fail?
Thanks for any help you can offer.I have a fix for inability to copy files. I had the same problem moving a lot of old files across my LAN from a Windows XP machine to a Mac Mini running Mountain Lion. After confirming copy of some special file, I would get an error that terminated the copy operation, and info on the Mac side would show a locked folder.
I finally decided to eliminate all special files on the Windows side, before copying, by running
attrib -s -h -r /s /d [drive or folder]\*.*
in a command window. Running attrib /? tells what the arguments mean, but it doesn't explain that you need the *.* to make the command go through the hierarchy clearing the special attributes on all the files.
After I did that, and then used drag and drop between two Windows Explorer windows (one on the Windows drive, on on the target drive on the Mac), the whole move operation ran to completion without stopping either for error or to ask for confirmation.
I do not have a fix for the inability to access some computers by name rather than by IP address. I'm looking into the possibility of activating bind on the Mac but I haven't done anything yet. -
Why has iTunes seperated a album into indevidual songs, which I have copied over from my external hard drive into iTunes? How can you pull all the songs back together into one album again?
Steve MacGuire a.k.a. turingtest2 - iTunes & iPod Hints & Tips - Grouping Tracks Into Albums - http://www.samsoft.org.uk/iTunes/grouping.asp (older post on Apple Discussions http://discussions.apple.com/message/9910895)
Quick answer: Select all the tracks on the album, File > get info, and either give them all a single "album artist", or check the "compilation" flag (as in https://discussions.apple.com/message/17670085).
If these are from multiple-CD sets you may also need to enter the appropriate information in the disc number fields. If they are not a multiple CD set you still need to make sure the disc number fields are set correctly or all empty. -
I have Elements 13 (I have the hard copy) installed on my iMac using Yosemite. I do all my iPhoto work on an external drive where I have copied my iPhoto Library, can I also install Elements 13 on my external harddrive or drag Elements 13 over from my iMac so that I can do work with Elements 13 via the exteranl hard drive? Thanks tb
Yes you can store images on an external hard dive and have them referenced in Organizer. It’s best to export copies to separate folders/subfolders and that will ensure iPhoto does not get corrupted.
Alternatively you could continue to use iPhoto with the Elements Editor set up in the iPhoto prefs as your external editing app. Then there is no need to use Organizer and no need to duplicate your images.
You can then call up photos directly from iPhoto as normal with the additional option e.g.
Double-click on a thumbnail to edit in iPhoto editor.
Control (right) - click on a thumbnail to edit in the elements app.
http://helpx.adobe.com/photoshop-elements/kb/photoshop-elements-iphoto-mac-os.html -
Batch Number Not copied over from Production order to Confirmation
Dear Experts,
In the production order, I specify the batch # for the components. But when I do the confirmation, the batch number for the components is not getting copied over.
Can anyone suggest what has to be done.
Regards
TomDario, I have not saved my confirmation. But when I execute CO11N and go to "Goods Movement" tab, I expect the Batch to be copied from the production order for the components. But the batch field is Blank.
How do we make the batch field to be copied over from the production order.
Thanks in advance.
Regards
Tom -
Can you run Preview from 10.4 on 10.5 if you copy it over?
Hi,
Given a few of the annotation limitations on Preview that ships with 10.5 I am currently adding annotations to pdf's via vnc to a 10.4 machine.
I am wondering if anyone knows if you can safely run preview from 10.4 on 10.5 if you copy it over? Does it mess with your plist?
Thanks in advance..It won't run "as is" you'll get a notice about it being the wrong version. However, a you can make it run if you want (I did because it does not have the "mushy looking pix" problems). See this:
http://discussions.apple.com/thread.jspa?messageID=5899045
Scroll to the bottom and see KCunningham and my comments on altering the info.plist and version.plist inside. I named my copy OldPreview, and it and the new Preview co-exist just fine.
Francine
Francine
Schwieder -
How do you use templates from external hdd? (without copying them over)
When I installed DVD Studio Pro 4, I had to install the Templates, Styles, Transitions, etc... into an external for lack of space in my MBP. Now comes the time when I need to use those templates, so how do I access them without having to reimport them? Importing them copies the template files over from the external to the internal and I can't afford the space.
How did you install them onto an external? If you did it via the FCS installer, then DVDSP should automatically link to them. If you just copied them over, it would probably be easiest to jus reinstall from the original discs, this time telling it to put the additional content on your external.
-
Migrating Wiki Calendars from Lion from Lion
This was an information article, since I spent a few hours on this one and there was no documentation and may help someone one day!
Description: This article was a guide on how to move a Wiki Calendar form a Lion server to another Lion Server.
Problem: Wiki Calendar Service wasn't running properly, and the service was stopped / restarted and never came back on. There was a few errors on our XServ regurading this, but since there was no phone support, I created a work around by migrating the data to another mini, to get calendars back up and running. This may come in handy for someone to migrate servers.
Another problem that came into factor here was also we upgraded from Snow Leapord, so instead of all of your files being in 1 place like they would be on a lion machine they were in multiple directories, which made the process more difficult.
Process: A few steps will have to be done in order for this to work. As our configuration was binded to AD, in a multi domain forest. Also remember the wiki calendars are inbended into the wiki, so not only moving the calendar files are enough to get it working on a different machine.
1) Bind to AD and get your 2nd machine up and running
2) Migrate the Wiki Calendars over using the KB article on apples forumn. http://support.apple.com/kb/HT5082
3) Copy the config files for the Calendar - I included the default folders for this below.
/Library/Server/Calendar and Contacts/Data ---> /Library/Server/Calendar and Contacts/Data on the new server
**note**
If you came from a snow leapord machine you will have a folder called migrated-data / .calendarserver_version files stored in a different place, once found it will have to be copied to /Library/Server/Calendar and Contacts/Documents
Both of these files need to be in this folder on the new server if your using the apple defaults ---> /Library/Server/Calendar and Contacts/Documents
I also had renamed my calendars-migrated to calendars-migrated-old after they were moved to the proper location.
The folder calendars-migrated will also have to be copied over via a USB drive since hidden attributes are embedded and any sort of network sync drops these files. (rsync / sftp) If you navigate into the calendars-migrated data, you will see filse like this with permissions drwxr-x---@ and you need to retain the @ if you have multiple calendars in 1 wiki.
Once the folder calendars-migrated is moved to the new location in /Library/Server/Calendar and Contacts/Documents/ you will have to use a chown to change the ownership of the permissions for the calendars-migrated folder
# sudo chown -R root:_calendar calendars-migrated
4) Next we will have to export the database for caldav
Stop the calendar / address book services
# sudo serveradmin stop calendar
# sudo serveradmin stop addressbook
Export the Database to the /tmp folder (file will be called caldav.pgdump)
# sudo pg_dump --format=c --compress=9 --blobs --username=caldav --file=/tmp/caldav.pgdump caldav
Move the file /tmp/caldav.pgdump from the old server to the new server on /tmp/caldav.pgdump.
One the new machine wipe the database so you can import it with the correct version (form moving the .calendarversion file over)
# sudo dropdb -U _postgres -i caldav
Create a new database on the new machine
# sudo createdb -U caldav caldav
Import that database to Collab so it can be used in the wiki
# sudo -u _postgres pg_restore -d caldav -U collab --single-transaction /tmp/caldav.pgdumpHi,
I'll just say my try of wiki migration from SLS(MacPro) to LS(MacMini with Internal Disk1&2).
1)Fisrt I made a bootable backup of SLS to Disk2 of MacMini.
2)Second I booted from Desk2. MacMini was running as SLS. After that, I installed Lion and LS from App Store.
Wiki migration was successful. So Disk1 is an original LS and Disk2 is LS with wiki migration.
Good luck!
Tac -
HP LaserJet MFP M476dw paper size mismatch when copying or scanning from ADF
We have HP Color LaserJet MFP M476dw that has an issue when copying or scanning from the ADF.
Put a single A4 sheet in the ADF and choose copy, with all settings correct & no resizing, and the output copy is moved down the page (increased top marging by a couple of inches).
My initial thoughts were a paper size issue (e.g. treating A4 as Letter or vice versa) but all settings look correct. I have even done a reset and started over and the problem remains.
If I take the original and place it on the flatbed and copy from there with all the same settings then it works fine.
There is a similar issue when scanning from the ADF. Again, scanning from the flatbed works fine.
I've tried all I can think of. Does anyone have any further suggestions? Could it be a fault in the ADF?
Here's the full device settings info:
Device Configuration
[Shop for Supplies][Support]
Product Information
Product Name:
HP Color LaserJet MFP M476dw
Formatter Number:
YF10C9X
Serial Number:
CNB7G2H6T9
Service ID:
24113
Firmware Datecode:
20131122
Disable Fax:
No
Telecom Version:
05-031-001
Location:
UK
ADF Installed:
Yes
Max Monochrome Print Quality:
600x8
Max Color Print Quality:
ImageREt 3600
Controller Number:
72
Duplexer Version:
0
Device Description:
HP Color LaserJet MFP M476dw
Language:
English
Default Settings:
Self-managed
Asset Number:
Your Company Name:
Contact Person:
Device Location:
Geo Location:
Product Security:
Off
Wired HW Address:
fc:15:b4:78:28:46
Wireless HW Address:
54:35:30:2f:d7:fc
Network In Use:
Wired
Host Name:
NPI782846
IPv4 Address:
192.168.9.18
IPv6 Address:
FE80::FE15:B4FF:FE78:2846
Total Memory:
256 MBytes
Available Memory:
117.7 MBytes
Installed Personalities and Options
PCL6
(20040201)
AirPrint
PCL
(20040201)
PDF
(20040201)
PS
(20040201)
USB Flash Drive:
Empty
Impressions
Total Impressions:
10684
Monochrome Impressions:
4799
Color Impressions:
5885
Total Equivalent Impressions (A4/Letter):
10684.0
Monochrome Equivalent Impressions (A4/Letter):
4799.0
Color Equivalent Impressions (A4/Letter):
5885.0
Duplex Sheets:
1223
Jam Events:
0
Mispick Events:
4
Photo Color Impressions:
0
Photo Monochrome Impressions:
0
USB Flash Drive Insertions:
0
Images Scanned to USB Flash Drive:
0
Copy Flatbed Images Scanned:
373
Copy ADF Images Scanned:
409
Copy Monochrome Impressions:
1122
Copy Color Impressions:
102
ADF Images Scanned to Host:
0
Flatbed Images Scanned to Host:
0
Images Scanned to E-mail:
0
Images Scanned to Network Folder:
0
Fax ADF Images Scanned:
23
Fax Flatbed Images Scanned:
1
Fax Impressions:
18
Images Sent from PC:
0
ADF Images Scanned:
1149
Flatbed Images Scanned:
779
Scanner Jam Events:
8
Paper Settings
Default Paper Size:
A4
Default Paper Type:
Plain
Tray 1 Size:
A4
Tray 1 Type:
Letterhead
Tray 2 Size:
A4
Tray 2 Type:
Plain
Paper Out Action:
Wait Forever
Manual Feed:
Off
Duplex:
Off
Bind:
Long Edge
Print
Auto Continue:
Off
Number of Copies:
1
Courier Font:
Regular
Orientation:
Portrait
Monochrome RET:
On
Wide A4:
No
Monochrome Resolution:
600
Monochrome Bits per Pixel:
8
Color Resolution:
600
Color Bits per Pixel:
32
IO Timeout:
120 Seconds
Jam Recovery:
Auto
Personality:
Auto
Print PS Errors:
Off
USB Flash Drive
Print Documents:
Number of Copies:
1
Paper Size:
A4
Paper Type:
Plain
Fit to Page:
On
Collation:
Off
Output Color:
Color
Print Photos:
Image Size:
10 x 15 cm
Paper Size:
A4
Paper Type:
Plain
Lighter/Darker:
<-----*----->
Number of Copies:
1
Output Color:
Color
Scan Settings:
Scan Resolution:
150
Scan File Type:
PDF
Scan Paper Size:
A4
Flatbed Scanner:
Single Page
Document Feeder:
1-Sided
File Name Prefix:
scan
Output Color:
Color
Copy
Optimize:
Auto Select
Lighter/Darker:
<-----*----->
Paper Size:
A4
Paper Type:
Plain
Collation:
On
Number of Copies:
1
Reduce/Enlarge:
Original=100%
Draft Mode:
Off
Tray Select:
Auto Select
Two-Sided:
1-Sided to 1-Sided
Multi-Page Copy:
Off
Fax
Your Company Name:
HP Fax
Answer Mode:
Automatic
Rings to Answer:
2
Distinctive Ring:
All Rings
Dial Prefix:
Off
Fax Resolution:
Fine
Lighter/Darker:
<-----*----->
Fit to Page:
On
Glass Size:
A4
Dialing Mode:
Tone
Redial if Busy:
On
Redial if No Answer:
Off
Redial if Comm. Error:
On
Detect Dial Tone:
Off
Billing Codes:
Off
Extension Phone:
On
Stamp Faxes:
Off
Private Receive:
Off
Confirm Fax Number:
Off
Allow Fax Reprint:
Yes
Print Duplex:
Off
Fax/Tel Ring Time:
20
Fax Speed:
Fast (V.34)
Error Correction:
On
Forward Fax:
Off
Block Junk Faxes:
Off
Phone Line Volume:
Medium
Alarm Volume:
Medium
Ring Volume:
Medium
Key-Press Volume:
Medium
Fax Confirmation:
Never
Fax Error Report:
Never
Include First Page:
On
Auto Log Print:
On
Print T.30 Trace:
Never
Paper Types
Plain:
Normal
HP Matte 90g:
Normal2
HP Matte 105g:
Heavy
HP Matte 120g:
Card stock
HP Matte 150g:
Extra Heavy
HP Matte 200g:
Extra Heavy
HP Glossy 120g:
Glossy
HP Glossy 150g:
Glossy
HP Tri Glossy 150g:
Glossy
HP Glossy 200g:
Heavy Glossy
Light 60-74g:
Light
HP EcoSMART Lite:
Extra Light
Intermediate:
Normal2
Mid-Weight 96-110g:
Heavy
Heavy 111-130g:
Card stock
Extra Heavy 131-175g:
Extra Heavy
Hvy Glossy 111-130g:
Light Glossy
X-Hvy Glossy 131-175g:
Glossy
Card Glossy 176-220g:
Heavy Glossy
Color Transparency:
Transparency
Labels:
Label
Letterhead:
Normal
Envelope:
Envelope
Heavy Envelope:
Heavy Envelope
Preprinted:
Normal
Prepunched:
Normal
Colored:
Normal
Bond:
Heavy
Recycled:
Normal
Rough:
Heavy
Heavy Rough:
Heavy
HP Tough Paper:
Tough Paper
Opaque Film:
Tough Paper
Energy Settings
Sleep/Auto Off After:
30 Minutes
Wake on These Events
USB Job
Yes
LAN Job
Yes
Wireless Job
Yes
Control Panel
Yes
Fax Ring
Yes
Shut Down After:
Never
LaserJet Updates Settings
Check Automatically
Yes
Prompt Before Install
Yes
Allow Downgrade
Yes
Allow Updates
Yes
Miscellaneous
Extended print modes modified:
No
Very Low Setting (Black Cartridge):
Prompt
Very Low Setting (Color Cartridges):
Prompt
Low Threshold (Black Cartridge):
5%
Low Threshold (Cyan Cartridge):
3%
Low Threshold (Magenta Cartridge):
3%
Low Threshold (Yellow Cartridge):
3%
Store Usage Data:
On Supplies
USB Connection:
No
Font Source:
I (Internal)
Font Number:
23
Font Pitch:
10.00
Font Point Size:
12.00
Symbol Set:
PC-8
Form Length:
64 Lines
Append CR to LF:
NoTo get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial product. You can do this at Commercial Forums.
I hope this helps!
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution! -
Copy selected values from a table control into another table control
hi there,
as seen in the subject i need to copy selected values from a table control into another table control in the same screen. as i dont know much about table controls i made 2 table controls with the wizard and started to change the code... right now im totally messed up. nothing works anymore and i don't know where to start over.
i looked up the forums and google, but there is nothing to help me with this problem (or i suck in searching the internet for solutions)
i have 2 buttons. one to push the selected data from the top table control into the bottom tc and the other button is to push selected data from the bottom tc into the top tc. does somebody has a sample code to do this?you're funny
i still don't get it... can't believe, there is no tutorial or sample code around how to copy multiple selected rows from a tc.
here's my code, maybe you can tell me exactly were i have to change it:
tc1 = upper table control
tc2 = lower table control
SCREEN 0100:
PROCESS BEFORE OUTPUT.
MODULE status_0100.
MODULE get_nfo. --> gets data from the dictionary table
MODULE tc1_change_tc_attr.
LOOP AT it_roles_tc1
INTO wa_roles_tc1
WITH CONTROL tc1
CURSOR tc1-current_line.
ENDLOOP.
MODULE tc2_change_tc_attr.
LOOP AT it_roles_tc2
INTO wa_roles_tc2l
WITH CONTROL tc2
CURSOR tc2-current_line.
ENDLOOP.
PROCESS AFTER INPUT.
LOOP AT it_roles_tc1.
CHAIN.
FIELD wa_roles_tc1-agr_name.
FIELD wa_roles_tc1-text.
ENDCHAIN.
FIELD wa_roles_tc1-mark
MODULE tc1_mark ON REQUEST.
ENDLOOP.
LOOP AT it_roles_tc2.
CHAIN.
FIELD wa_roles_tc2-agr_name.
FIELD wa_roles_tc2-text.
ENDCHAIN.
FIELD wa_roles_tc2-mark
MODULE tc2_mark ON REQUEST.
ENDLOOP.
MODULE ok_code.
MODULE user_command_0100.
INCLUDE PAI:
MODULE tc1_mark INPUT.
IF tc1-line_sel_mode = 2
AND wa_roles_tc1-mark = 'X'.
LOOP AT it_roles_tc1 INTO g_tc1_wa2
WHERE mark = 'X'. -
> big problem here is, that no entry has an 'X' there
g_tc1_wa2-mark = ''.
MODIFY it_roles_tc1
FROM g_tc1_wa2
TRANSPORTING mark.
ENDLOOP.
ENDIF.
MODIFY it_roles_tc1
FROM wa_roles_tc1
INDEX tc1-current_line
TRANSPORTING mark.
ENDMODULE. "TC1_MARK INPUT
MODULE tc2_mark INPUT.
IF tc2-line_sel_mode = 2
AND wa_roles_tc2-mark = 'X'.
LOOP AT it_roles_tc2 INTO g_tc2_wa2
WHERE mark = 'X'. -
> same here, it doesn't gets any data
g_tc2_wa2-mark = ''.
MODIFY it_roles_tc2
FROM g_tc2_wa2
TRANSPORTING mark.
ENDLOOP.
ENDIF.
MODIFY it_roles_tc2
FROM wa_roles_tc2
INDEX tc2-current_line
TRANSPORTING mark.
ENDMODULE.
thx for anybody who can help with this! -
I am trying to copy 3 photos from an album in iPhoto to my iPhone. I have tried to move them to PhotoStream. I "select" the photos in the Album and then click on PhotoStream in the "Share" menu at the bottom of the screen. Nothing happens. I have also tried emailing them tyo myself but iPhoto won't send the email. It tells me it doesn't recognize my ID and password. My operating is Lion on an iMac.
Thank you for responding to my question, above, this morning. And thank you for the link about PhotoStream. It was helpful in understanding how Photostream works, but, unfortunately, doesn't really reference my problem since it assumes that the photos were originated on one of my Apple devices. The photos I want to copy to my iPhone are in an album on iPhoto but I had originally downloaded them from my camera to my iMac then moved them to the album. The confusing thing for me is that they are 3 of a dozen photos takern over a period of 12 years on different digital cameras (two were taken on film and later scanned and eventually moved to the album in iPhoto) and all but three of the photos moved to photostream and are on my iPhone. It is those three, which were all taken on digital cameras and moved to the album, which I can't get to move to Photostream.
-
Copy Query Variants from InfoCube to MultiProvider
Hi,
Is it possible to copy query variants from an infocube to a multiprovider?
Basically, we used RSZC to copy the queries from the infocube to the multiprovider, but it doesn't look like the variants were copied over. Is there an ABAP program or some other workaround that can expedite/facilitate in recreating the variants on the multiprovider queries?
Your help is much appreciated.
Thanks,
KK
Edited by: Kristin Kalalau on Jan 29, 2009 10:48 PMIt is possible to copy but the only requirement is your target cube structure should match with the source cube structure.
Thanks...
Shambhu
Edited by: Shambhu Kumar Gupta on Jan 30, 2009 12:01 PM -
How Can I copy purchased books from my MAC book iBooks to my iPhone iBoooks
I wasn't sure where to put this because it has to do with my Macbook air and my iPhone 5S and iBooks on both units.
I am using iBooks version 1.01 (281) on my MAC book Air. My OS is OS X version 10.9.4 Mavericks.
About two weeks ago, I upgraded my iPhone 4S to a iPhone 5S (64 gigabyte). I currently have iOS 8.0 on the iPhone.
So, I have lots of books that I have purchased over the years from iTunes and now iBooks. All of them have been backed up to the cloud. They were also backed up to iTunes on my MAC from my 4S.
I tried to download the books from my iCloud to my iBooks on the new 5S and it all worked. But there is one missing book. (Staying Strong by Demi Lovato) I have purchased this book three times from iBooks. All three purchases are still listed in my purchase history there. It is in my MAC book iBooks library (but no longer in iTunes because Apple separated the Apps a while ago). And I can read it there. But it is NOT in the iCloud for some reason.
Everything I find on the Apple site refers to iTunes which is outdated since it is no longer part if iTunes (now it's a separate app). Where can I find information on how to copy the book from my iBooks app library to my iPhone iBooks app so I can read it on my iPhone 5S? Is there a way to even do this? Do I have to buy it agin for the fourth time?
I don't want to go back to that lousy PC?When I connected my iPhone, it automatically synced right away. I did click on the iPhone button and saw the contents of my iPhone including the Books. When I clicked that 'Books' button. But since the book in question was not on my iPhone, it did not show up in the list so I could not select it like you suggested. Therefore I could not sync that book to my iPhone. Thanks for the help though.
The good news is I did manage to get the book on to my iPhone.
When her book came out for preorder about a year or two ago, I looked for it in the iTunes store and preordered it. About a week after it came out, I found what was basically the same book for a dollar more. ($7.99 and $8.99) I figured there must be something additional (features) in the $8.99 book. So I bought it too. As far as I could tell though, they were exactly the same. So I decided to hide one of them so they would not both show up in my Library. Anyway, I went to my iTunes/iBooks account and managed the hidden books area. I unhid the Demi book and then it showed up in my iCloud to download on my iPhone. Now they are both on my computer so I need to figure out which one is the other one and hide it. So then I can delete it from my computer just have the one that is on my iPhone on both systems. But at least I found a way to get a copy on my iPhone.
Maybe you are looking for
-
Error in SFTP receiver channel
Hi, We are getting following error while processing the SFTP receiver channel. There is a 64 MB file which need to be processed and while processing we started getting the error log.(We have processed more that 80 MB files from the same channel.) The
-
What column pertains to payment document number(AP)
Hi, what column pertains to payment document number or Payment Voucher Number as well as Related AP Voucher Number (This is the pre-defined voucher number generated by Oracle). Please include the table_name (ex test.pdn). Thanks Edited by: 796711 on
-
How to use console font in terminal
i love console font and color in the way it appears. there are some thread but it's not actually a solutions. https://bbs.archlinux.org/viewtopic.php?id=138811 https://bbs.archlinux.org/viewtopic.php?id=77522 is it possble to convert bitmap font to t
-
Conditional Display in reports doesnot seems to work
hi , I tried to set conditinal display in a report to a pl/sql expression and it didnt work. in order to check if conditinal display works I tried to set it to never, and it is still displayed . I'm using Apex 2.0 Please help sagsag
-
Cannot set ringtone!!
I have had my Palm Pro for a while now, this is my second one actually and my first one had the same problem. How exactly do you change your incoming call ringtone? I put my ringtones in the My Ringtones folder. I long select and choose "set as ri