10.8 System Image Utility does not recognize anything 10.7 or below

I just installed Mountain Lion  server and was excited to start using system restore to make images of some Lion Minis we have. However, SIU 10.8 does not seem to recognize a 10.7 volume. I tried booting the machine I planned to image in target disk mode and I tried making an image using disk utility and mounting it. Neither worked. Can someone please confirm or deny whether this works. If 10.8 Server SIU does not support older verisons (If you can really call Lion that much older for **** sake). It willbe infuriating to me if this can't be done because this would just be another example of Apple taking a good idea and just royally tanking on the execution side.
I did go ahead and install Server Admin tools on one of the other Lion minis and am making a Netrestore image of the master mini as we speak; so far so good. But I am skeptical of whether my Mountain Lion Server will even accept and deploy this image considering my less than stellar experience so far.
Any thoughts, suggestions, shared frustrations are all appreciated.

SIU has never supported anything but the OS that it comes on. So you need Server running on Mountain Lion to build Mountain Lion images, and Server running on Lion to build Lion images - etc for Snow Leopard, and Leopard, and Tiger...

Similar Messages

  • Image capture does not recognize Canon Scanner

    I have two Canon Scanners, a Canoscan 8800F and a Canoscan LiDE 60. Image Capture does not recognize either of these. Both worked with Mountain Lion.

    This user found some success acutally using *older* drivers. While that sounds odd, it might be worth a try: https://discussions.apple.com/message/23759017#23759017
    I used to have a LIDE 60 - it is a great little machine. Good luck!

  • I have an iphone 3g which brought him use me when I brought it worked fine, I updated the system to 4.3.3 and no longer recognizes any network operator, look at the baseband and 5.16.02 and says it is it does not recognize anything I can do? the operator

    I have an iphone 3g which brought him use me when I brought it worked fine, I updated the system to 4.3.3 and no longer recognizes any network operator, look at the baseband and 5.16.02 and says it is it does not recognize anything I can do? the operator to buy my iphone was a 4 but it was stolen, I thought I could use this but aparentementeno, I can do to make it recognize my carrier? thanks

    Looks like you have relocked a hacked phone when you updated.  The only way to fix it would be if you could figure out the original carrier and see if they would unlock it.

  • Image Capture does not recognize my Canon Pixma MP150 printer

    Image Capture does not recognize my Canon Pixma MP150 printer since I upgraded to Mavericks.

    To scan with Image Capture you need an ICA driver. Looking through the CanonDevices list in the /Library/Image Capture folder I cannot see an entry for the MP150. And I checked Canon Australia's web site and there is no ICA driver for the MP150. There is a scanner driver and MP Navigator for OS X 10.7. You may be able to install and use the driver and application on 10.9, although you will have to get past Gatekeeper to install both items as they are not digitally signed. To do this, you can hold down the Control key and click on the installer. A pop-up menu will appear and you can select Open. You will then be able to install the driver and then the application. If they do install then see if you can open MP Navigator and scan from the MP150.

  • HT1369 Brand new computer with Windows 8.1 will not sync with iPod Classic 120G.  Windows does not recognize anything but iPod Touch?  Is there a simple sloution?

    Brand new computer with Windows 8.1 will not sync to iPod Classic 120G.  Windows does not recognize anything but iPod Touch?  Is there a simple solution.  Diagnostics have run and failed to point to a fix.

    Might be worth tearing down the whole iTunes install and starting over...
    Go to Control Panel > Add or Remove Programs (Win XP) or Programs and Features (Later)
    Remove all of these items in the following order:
    iTunes
    Apple Software Update
    Apple Mobile Device Support
    Bonjour
    Apple Application Support
    Reboot, download iTunes, then reinstall, either using an account with administrative rights, or right-clicking the downloaded installer and selecting Run as Administrator.
    See also HT1925: Removing and Reinstalling iTunes for Windows XP or HT1923: Removing and reinstalling iTunes for Windows Vista, Windows 7, or Windows 8
    Should you get the error iTunes.exe - Entry Point Not Found after the above reinstall then copy QTMovieWin.dll from:
    C:\Program Files (x86)\Common Files\Apple\Apple Application Support
    and paste into:
    C:\Program Files (x86)\iTunes
    The above paths would be for a 64-bit machine. Hopefully the same fix with the " (x86)" omitted would work on 32-bit systems with the same error.
    tt2

  • Image Capture does not recognize my CanoScan LiDE 700F after downloading pix via iPhoto.

    My scanner was working fine. I downloaded some photos using iPhoto. My computer now does not recognize my scanner when I use ImageCapture. I think this happened once before but I can't remember how I remedied the situation. In researching the scanner before purchase, I discovered many reviews that indicated "don't download the software; it doesn't work: just use ImageCapture. That has worked well....until now. Any suggestions?

    Try resetting the printing system. It can also affect the scanner.
    OS X Mavericks: Reset the printing system
    You can also check for drivers here.
    Gimp - Print
    HPIJS for Mac OS X

  • Image Capture does not recognize scanner with latest update of Mavericks 10.9.4

    Since last week (8-5-14) after updating to OS 10.9.4 (13E28) Image Capture and Printers and Scanner (in System Prefs.) do not recognize my scanner. What the hay! Yes, my scanner is elderly but like me is in perfect working condition. Until now. I've spent hours trouble shooting, i. e., downloading EPSONPrintDriver2.18.dmg and reinstalling, a waste of time. Changing usb/firewire cables, switching usb ports, deleting pref files and cussing. The Epson web site was useless it just tells me to download updates via Apple software updates. I hate the idea of being so dammed dependant on any one organization (Apple). I've been an Apple user since the Apple 2C but I do believe that will change soon.
    Anyone with a solution or replacement app for Image Capture? I don't want to spend my Social Security money on VueScan which dose work for me unless I have to.

    Try resetting the printing system. It can also affect the scanner.
    OS X Mavericks: Reset the printing system
    You can also check for drivers here.
    Gimp - Print
    HPIJS for Mac OS X

  • Disk Utility does not recognize internal HD

    Hello community!
    I am a computer lab assistant (all iMacs) for my work and am troubleshooting a problem as follows:
    Specs:
    Mac A:
    OS X 10.8
    2.7 GHz Intel Core i5 processor
    4 GB 1333 MHz DDR3 memory (2 slots x 2 GB in use, 2 slots empty)
    27-inch Mid-2011 iMac
    Graphics: AMD Radeon HD 6770M 512MB
    The problem is that Disk Utility does not always recognize the internal HD on mac A. In fact, only once it showed up recently and that was after a couple of restarts. Programs run very slowly and are not very responsive.
    Troubleshooting steps taken thus far:
    1. restarted mac A in internet recovery mode and ran Apple Hardware Test about 8 times (quick test 4 times and extended test 4 times). Every time it hangs indefinitely on the memory check.
    2. Installed and ran memtest in single user mode (mac A) with arguments "all 2" to run the test twice. All tests passed.
    3. Started up mac A in Target Disk Mode and booted mac B via firewire. Everything runs fine (fast), but disk utility installed on mac A's HD does not recognize any HD (neither firewire nor internal).
    4. Started up mac B in target disk mode and booted mac A via firewire. Everything runs fine (fast). Disk Utility on mac B's HD recognizes both firewire HD (of mac B) and internal HD (of mac A). Disk Utility verify and repair completed on mac A's internal HD. Everything OK.
    I'm unsure how to proceed. I assume the RAM on mac A is fine because it runs mac B's HD via firewire very fast (it handled opening all the apps on the doc simultaneously relatively well). I assume mac A's HD is fine because via firewire it shows up in disk utility and runs very fast on mac B. I just don't understand why Mac A's HD won't work well on mac A. Could it be a loose SATA connection between the HD and the logic board? Would that cause these symptoms?
    Thanks for any input.

    I ran Data Rescue 3 by Prosoft and it returned the following graph:
    In case you can't see the stats, that green spike is up to 30,000 msec in readtime for the HD. The smaller spikes before and after it are at about 2,000 - 3,000 msec. The threshold (red line) is a recommendation: persistant read times above the red line (about 1,000 msec)  could indicate a problem with the HD according to the program. I guess it's time to see about replacing the HD.
    Thanks.

  • Airport utility does not recognize base station

    My airport utility (5.5.3) does not recognize my base station or express after changing internet providers (moved to ATTUverse). I know the network works (recognized by wireless devices). Everytime I do a "rescan" nothing appears. Running OS 10.72 on Core 2 Duo iMac; all software up-to-date; restarted all devices. Help

    It sounds like you may have an older version of the AirPort Express.
    Please look on the side of the device in the faint print to locate the model number. It will start with an "A" followed by four numbers......as in A x x x x.
    If you could post back with that information, we will know more about how to answer your question.

  • Windows 7 airport utility does not recognize my airport extreme

    My iphone connects to my airport extreme and the airport utility sees it. So does my ipad and my friends laptop.
    When I use wifi or wired connection (to lan port) from Windows 7 laptop to my airport extreme. The airport utility does not "see the extreme.
    I've uninstalled/reinstalled the following:
    - bonjour
    - airport utility
    - itunes.
    I've wasted 3 hours on this.
    Any help will be greatly appreciated.....

    UPDATE
    * I located the IP address and admin password of the airport extreme and was able to log into to the (File / configure other) airport extreme.
    I believe it's a W7 bonjour issue.
    As you can see in my attachments, Bonjour is installed however msconfig running services show it as stopped. I can't get it to start.
    ** How can I force bonjour to start? **
    Here are my replies to your recommended steps:
    What version extreme are you talking about? Actual model A1xxx from the base is a big help.
    - I forgot to check this
    Step 1.. Ping.. Ping is your most important tool to find things on a network.
    Open a command window and type ping 10.0.1.1 (or whatever is the current IP of the extreme).
    - Yes, I can ping it.
    Please turn off all firewalls.
    - Yes, firewall is off
    Make sure the win7 is not in homegroup.
    - done.
    Make sure win7 is set to home.. not work or public for location of the network.
    - done.
    Step 2. .. This assumes you now have ping response.
    In whatever airport utility you like, reset the extreme to use all SMB names.
    - WHERE do I make these changes?

  • Disk utility does not recognize internal drive

    iMac Core 2 Duo previously running Mountain Lion OSX quit recognizing the internal 1 GB boot hard drive. Have attempted repair with Disk Utility but Verify says that the drive is fine yet it will not boot. Can boot from an external USB drive running latest version of Mavericks. Have also tested internal drive using latest version of TechTool Pro 7 but without success. TechTool Pro recognizes the external USB boot drive but does not visualize the internal drive. Cannot visualize internal drive to erase and reformat.
    Any suggestions for visualization of internal drive and repair? Or is this likely a dead Apple internal HD?

    While booted from your external drive or boot from the Recovery Drive, run Repair Drive in Disk Utility.
    Boot into the Recovery Drive by holding down Command R when restarting.
    Run Repair Drive
    It sounds like the internal drive might be dead. If you replace, I suggest SSD drive. They are really fast.
    Under About this Mac,
    Open System Profiler > Hardware
    Copy the Serial number and model identifier. You can use this info to shop for a new drive.
    Go to this site and check out their drive prices and videos to see if you can do the install yourself.
    http://eshop.macsales.com/installvideos/

  • Utility does not recognize airport express

    my wifi works normally but the utility is unable to recognize the airport express

    I do not see a menu in the airport utility, but there is a tool bar.
    The menus.....like File, Window, Edit, Help, etc are all located where menus are normally located.....at the very top of the computer screen. It sounds like you are looking at the AirPort Utility window in the middle of the screen.
    Did you power off the restart both the PC and the AirPort Express? If you have done this, and the AirPort Express does not appear when you open AirPort Utility, then more troubleshooting will be required.
    If AirPort Utility on your PC is communicating with the AirPort Express, the window in the center of the screen will look similar to  this when AirPort Utility is first opened, except that you will see a listing for the AirPort Express:

  • Image Capture does not recognize RAW files from Panasonic Lumix G1

    I'm in the process of buying a Lumix G1 camera, but while uploading images from the camera in the store via Image Capture, said app did not recognize its RAW files, only the JPEGs. It works fine with other new cameras such as Nikon D5000, etc. Any ideas?
    BTW, my Powerbook is still running Tiger, and I want it that way!

    http://elstudio.us/?tag=lumixg1

  • Disk Utility does not recognize ethernet external drive

    I recently purchased a lacie ethernet external drive 1.5Tb to use with time machine and need to partition it. I mount the drive and open up disk utility, but it does not show up there. Any suggestions?

    You cannot partition and format a drive over the network. You will need to connect the drives directly to your computer first in order to partition and format them (unless that's already been done at the factory.) Read the documentation that came with them product or contact LaCie's tech support.

  • Disk Utility Does Not Recognize External Burner

    I have had recent problems with errors in the burning process with idvd 5.
    I have no problem making a disk image, so I can burn using disk utility. The problem is that disk utility only recognizes my internal drive and not the external LaCie d2 burner. The burner is listed in the system profile, idvd recognizes it ok, Toast recognizes it ok, but the disk utility doesn't.
    I need to burn on dvd+r so that I can use Lightscribe, but the internal burner only takes dvd-r. I also would like to burn the dvd with the menu from the idvd program which is not there if I burn using Toast.
    So, how can I get my disk utility to burn onto an external drive?

    Does this help?
    http://homepage.mac.com/geerlingguy/macsupport/mac_help/pages/00152-burn_idvd5.html

Maybe you are looking for