100-pin Connector Required when Building Custom Cable for PCI-6031E

Four 100-pin connectors are required to make custom cables to connect the PCI-6031E. Where can I get this connector?

Hi Tom,
Thanks for your reply. The ringing (noise if you like, but it is definetly being coupled to the output signal from the source) is occuring during both the logic low and logic high periods of the output. I agree, this is still within the TTL noise margins, but is staying within the margins the only important thing? - e.g. what happens multiple devices are clocked using the same output pulse - the pulse shape is degraded slightly due to cabling and input capacitance etc, and now, because of the additional ringing, the logic thresholds are being crossed when they shouldn't be. If you consider that the source signal is 5Vpp and the induced ringing is 0.4Vpp then the rejection ratio would be 20*log10(0.4/5) = -22dB, not very good. The situation is not as bad when one of the internal timebases is used as the source but this particular application requires an external one. So, I'm looking for ways to reduce the ringing if you're aware of any. One possibility might be to reduce the cable length - I'm using the 2m cable so maybe you could try the 1m cable for me and see if things improve.
Jeff

Similar Messages

Need the SCSI-II 100-pin connector for the PXI-6624

Hi. I need to build a custom cable for the NI PXI-6624 and I would like to know where can I get the 100-pin connectors. Thank you.
Daniel
Chile

You should be able to find the connectors here:
Subminiature and Microminiature D Connectors .050 Series Cable Connectors (SCSI)AMP (749111-8)
The parts are made by Tyco Electronics P/N: 749111-8
Otis
Training and Certification
Product Support Engineer
National Instruments

TS2634 I bought a composite AV cable with 30 pin connector at a proper apple store for my ipad 2 which no longer works now i have updated to ios7 - please advise how to make this work ?

I bought a composite AV cable with 30 pin connector at a proper apple store for my ipad 2 which no longer works now i have updated to ios7 - please advise how to make this work ?

I have the same problem.
Two similar discussions:
https://discussions.apple.com/message/23081658#23081658
https://discussions.apple.com/message/23281391#23281391
I have not yet seen any official response to the question: "Is the Apple AV Composite cable fully supported with 30pin connector devices upgraded with iOS7 - specifically ? - eg. iPad 2, iPhone 4, iPhone 4s"
If it is not currently supported is that then due to a bug / oversight and in that case is it something that will be fixed in the near future?
Please let us know what feedback you got from asking Apple support.

Error message when building an application for Labview PDA

When using LabView PDA module to build an application for a PDA target, I receive the following message: "Error building executable. Unable to create file". Why is this happening?
When looking at the error log, it reads "The system cannot find the file specified."
This happens even when looking at one of the Labview PDA example VI's, so it is not a result of the VI containing functions of features not supported by Labview PDA.
When installing Labview PDA, I installed files as follows, and in this order:
(i) Labview 7.1 (installed previously)
(ii) Microsoft eMbedded Visual C++ 4.0
(iii) Microsoft eMbedded Visual C++ 4.0 SP 3.0
(iv) Microsoft SDK for Windows Mobile 2003-based Pocket PCs
(v) Microsoft ActiveSync 3.8
(vi) NI Labview 7.1 PDA module for PocketPC
(vii) DAQmx Base 1.0 for PDA or later
Any ideas?

Did you attempt to add the _wordsub.llb and _excelsub.llb files to the application as support files? I believe in LabVIEW 8.0 instead of adding the entire LLBs you should just add the _Word Dynamic VIs.vi and _Excel Dynamic VIs.vi as dynamic VIs. I think I've seen a similar post on the discussion forums in the past that recommended this.
If this suggestion doesn't help, please reply, and attach a simple VI and .lvproj file demonstrating the problem so I can investigate further.
Good luck,
-D
Darren Nattinger, CLA
LabVIEW Artisan and Nugget Penman

What jars are necessary when building an Executable for JAXB??

I'm using JWSDP-1.2. I get the following error when I try to run my executable: DefaultValidationEventHandler: [FATAL_ERROR] Document root element is missing. I was curious which jars are necessary when making an executable for JAXB. So far I have: 1)dom.jar, 2) jaxb-api.jar, 3) jaxb-impl.jar, 4)jaxb-libs.jar, 5)jaxb-xjc.jar, 6)jax-qname.jar, 7)namespace.jar, 8)relaxngDatatype.jar, 9)sax.jar, 10)xalan.jar, 11)xercesImpl.jar, 12)xsdlib.jar . Are there any jars I'm missing? I thought I might be getting the error due to a missing class. I've made sure that the XML document is readable and that it exists. The application runs fine in Eclipse, but when I make an executable I get the ERROR message.

I'll have to read up on the doctype stuff, but I don't have anything like that included. Is it necessary? I read from the same XML document when I run inside Eclipse and also read the same document when I run the jar.
Below is the XML document I use and below the XML code is the code I use for my schema:
<?xml version="1.0" encoding="UTF-8"?>
<Information>
<Employee number="1" TabPn="true">
    <FName>Jack</FName>
    <LName>Perry</LName>
    <Status>Part Time</Status>
    <Title>Software Developer</title>
    <DaysEmployed>
      <WorkDay>Monday</WorkDay>
    </DaysEmployed>
</Employee>
<Employee number="2" TabPn="true">
    <FName>Bob</FName>
    <LName>Smith</LName>
    <Status>Full Time</Status>
    <Title>Janitor</title>
    <DaysEmployed>
      <WorkDay>Monday</WorkDay>
      <WorkDay>Tuesday</WorkDay>
      <WorkDay>Wednesday</WorkDay>
      <WorkDay>Thursday</WorkDay>
      <WorkDay>Friday</WorkDay>
    </DaysEmployed>
</Employee>
<Employee number="3" TabPn="true">
    <FName>Fred</FName>
    <LName>Williams</LName>
    <Status>Full Time</Status>
    <Title>Sales</title>
    <DaysEmployed>
      <WorkDay>Thursday</WorkDay>
      <WorkDay>Friday</WorkDay>
    </DaysEmployed>
</Employee>
</Information>------------------------------------------------------------------------------------------------------------------------------------------------
Schema:
<?xml version="1.0" encoding="UTF-8"?>
<xs:schema xmlns:xs="http://www.w3.org/2001/XMLSchema">

<xs:element name="FName" type="xs:string"/>
<xs:element name="LName" type="xs:string"/>
<xs:element name="Status" type="xs:string"/>
<xs:element name="Title" type="xs:string"/>
<xs:element name="WorkDay" type="xs:string"/>

<xs:attribute name="number" type="xs:positiveInteger"/>
<xs:attribute name="TabPn" type="xs:boolean"/>

<xs:element name="DaysEmployed">
<xs:complexType>
    <xs:sequence>
      <xs:element ref="WorkDay" maxOccurs="7"/>
    </xs:sequence>
</xs:complexType>
</xs:element>
<xs:element name="Employee" >
<xs:complexType>
    <xs:sequence>
      <xs:element ref="FName"/>
      <xs:element ref="LName"/>
      <xs:element ref="Status"/>
      <xs:element ref="Title"/>
      <xs:element ref="DaysEmployed"/>
    </xs:sequence>
    <xs:attribute ref="TabPn" use="required"/>
    <xs:attribute ref="number" use="required"/>
</xs:complexType>
</xs:element>
<xs:element name="Information">
<xs:complexType>
    <xs:sequence>
      <xs:element ref="Employee" maxOccurs="unbounded"/>
    </xs:sequence>
</xs:complexType>
</xs:element>
</xs:schema>

Icon path restricted error when building release version for ipad3

Hi,
i get the following error when building the release build ipa file for ipad 3: "The path icon.png is restricted. If you were trying to package Icon.png you should correct the case." In debug mode everything works. My icon is under assets folder and added in the app-xml with:
<icon>
<image72x72>assets/icon_72.png</image72x72>
</icon>
Did I missed something in configuration? Seems to be that the problem is known but cant find a solution for it. If i try to packegae per command line despite the fact building works I could not install the app. When I change the icon tag to use no icon everything works fine. Any ideas?
Greetz and thanks in advance!

I solved it. When you export the release build you can choose package contents to be compiled in the ipa. When I tried to add an icon at first I named it icon.png, which seems to be a reserved name. The configuration to include this icon.png was still saved though i deleted it. Wired... After unchecking the ceckbox for icon.png not to be compiled in the ipa, the release build was build.

Y-splitter cable for PCIe card

I am considering a Dynex 2-Port FireWire 800 and 1-Port FireWire 400 PCIe Adapter (DX-PCI2PF) for my Mac Pro. The card has a 4-pin power connector to receive extra power, if desired.
Where can I find a cable that goes from one of the power connectors on the motherboard of the mac Pro, split it, and one of the Y legs go to the 4-pin connector on the card?
I could do without a Y. But, since one of the power connectors on the motherboard is already used for a 2nd video card, I would like to give myself an extra power connection after installing the Dynex card.

*The hatter* - Thanks for your quick reply!
Actually, I was looking at this card on eBay:
http://cgi.ebay.com/Dynex-2-Port-800-1-Port-400-FireWire-PCIe-Adapter-DX-PCW0QQitemZ330419493351QQcmdZViewItemQQptZLH_DefaultDomain_0?hash=item4cee8959e7#h t_775wt941
The description states "Built-in 4-pin power connector for receiving extra power supply." That's why I became curious.
The FW800 port on the back of my Mac Pro is already used to connect to a FW800 hub that is 15 feet away. And, I want to have at least two more FW800 ports to attach (1) OWC's Mercury On-The-Go Pro drive and (2) MacBook Pro in Target Disk Mode.
For my purpose, do you know that these PCIe cards would not need extra power supply?
Also, what would one connect to these PCIe cards that necessitates extra power supply?

What are the best specs when building a PC for video & where to buy in US?

Our current video machine has died - a problem we have constantly battled over the years with our video machines, primarily from the heat generated in the system. These have been spacious, well spec'd out desktops, so while I'm budget concious I thought I'd reach out for advice before going ahead. The biggest problems occur when rendering video, esp. larger files.
Also, I'm visiting the US for a few weeks, so that opens up some new possibilities (it's common to see much better pricing for systems in Canada than the US.)
So my questions are two-fold.
1) What would you recommend for buying a PC video machine today, while still on a budget? I would normally look for a higher end i7 processor, 16 Gb DDR3 ram, dedicated video card, ASUS motherboard with raid 0/5 and a couple of decent sized harddrives (not striped... had terrible experiences with my striped drives in the past). In particular, what would you recommend on the video card front for the best value/performance while not creating issues with heat (this is where I've had problems with a number of machines in the past)? In terms of harddrive management, are there some better options now for handling real time editing and rendering? (I would like to connect the 2 harddrives from the machine that has failed to the new machine.)
2) I'm in Ft. Myers, FL for the next couple of weeks... what are some good options for either having a machine built or getting the parts to build myself? (I don't need an OS, but will install Win 7 Pro myself.) Normally I'd look to TigerDirect or CanadaComputers for a new system.
My main use for the machine will be Premiere/After Effects, with some Photoshop/Illustrator.
Any other advice/input on how to optimize the machine so that I don't have HDD issues and other isssues from overheating would be appreciated. Please keep in mind, I'm on a budget (which means I'd ideally like to spend between $800-$1300). :-)
Thanks!
Julie

Build a Desktop Video Editing PC
-3 price level ideas in http://www.pacifier.com/~jtsmith/ADOBE.HTM
-what PC to build http://forums.adobe.com/thread/947698
-2 how to build videos http://forums.adobe.com/thread/1104182
-another video http://forums.adobe.com/thread/1145366
-planning & Building http://ppbm7.com/index.php/intro-part-1
-memory for LGA2011 http://forums.adobe.com/thread/1098759
-an Adobe FAQ http://forums.adobe.com/thread/878520
-http://www.shawnlam.ca/2012/premiere-pro-cs6-video-editing-computer-build/
-http://www.videoguys.com/Guide/E/Videoguys+DIY9+Its+Time+for+Sandy+Bridge+E/0xe9b142f408a2 b03ab88144a434e88de7.aspx
-several more links http://forums.adobe.com/thread/815798
-build tuning http://ppbm7.com/index.php/final-results

Error when Building DC Project for CAF Entity Service

Hi All,
I got the following error message when Im building my CAF DC Project for Entity Services:
01.02.2008 12:09:10 /userOut/Development Component (com.sap.ide.eclipse.component.provider.listener.DevConfListener) [Thread[ModalContext,5,main]] ERROR: ewrdata/metadata: Failed to read component definition from local file MyComponents:com.cas.elisa.gp/ewrdata/metadata : Cannot read component definition. File does not exist: C:\Documents and Settings\tfelp4\.dtc\LocalDevelopment\DCs\com.cas.elisa.gp\ewrdata\metadata\_comp\.dcdef (Cannot read component definition. File does not exist: C:\Documents and Settings\tfelp4\.dtc\LocalDevelopment\DCs\com.cas.elisa.gp\ewrdata\metadata\_comp\.dcdef)
But ".dcdef" file exists, its an XML file.
My NWDS environment is 7.0.13.
I used the tutorial exactly how it was written in the tutorial from SAP:
http://help.sap.com/saphelp_nw04s/helpdata/en/05/3a0741b5b7ee6fe10000000a1550b0/frameset.htm
What could be the problem?
Thanks for helping me...
Steve

Hi Chandan,
Can you do person.getRelatedModelObjects() and get the contact object, to check whether it is null, also check in the CAF DB whether the data you entered is present.
I am not sure the code is actually adding the contact model object to person.
Go thru this SDN Blog on usage of the CMI API's, there is a link for CMI documentation in it which might help you get the right code for adding the contact object.
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/cef4f43e-0d01-0010-db84-ede25c874115.
award points if info is helpful
Regards,
Anish

Converting from Ipod 30 pin connector to Blackberry Bold 9700 mini for car

I just bought a 2009 Audi A4. It has the ipod hook up that has a plug for the 30 pin Ipod intergration. My wife uses her iphone in the car, but I need a solution for using my blackberry and being able to hook it into this system. Does any one know of a converter cable that goes from the ipod cable to a usb mini for my Blackberry 9700 bold?

No. Video output is not supported through either Lightning to 30-pin adapter (with or without cable).

Changing the compiler in the SDK when building a BSP for a Zynq

Hi,
I have a zedboard and I need to get software running in a bare bones AMP situation using the IAR compiler. There is an eclipse plugin that I've manged to add to the SDK and I can get non BSP apps to use the IAR compiler, but not build/link as the BSP wont build with IAR.
Looking through the SDK files I can see that there are some files to support the IAR compiler (C:\Xilinx\SDK\2015.2\data\embeddedsw\lib\bsp\standalone_v5_1\src\cortexa9\iccarm) however I can't figure out how to point the BSP at these files instead of the GCC ones.
I feel like there's something simple I'm missing, like there should be an option in the BSP generation process or something.
Has anyone else tried to go this?
This was from a custom hardware design exported from Vivado 2015.2.
Thanks

Thanks, these helped a lot.
I had to add the complier directory to my PATH variable.
I found that I couldn't use the GUI to change the compiler flags and it kept passing -O2 -c to the compiler, neither of which are valid for IAR. So I had to manually edit the make file, this causes a problem if I try and re-open the options via the GUI and re-generating the sources deletes my change, but it does work.
A couple of the other make files needed modifiying as well, XCoresightPs - needed to specify the cpu (IAR option --cpu= Cortex-A9) and the XGpio make file just needed a complete re-write no idea what was going on there, I copied a working one and changed the names.
Also, for any other IAR users out there; --diag_suppress=Pa050 is a must, (removes warning about non native line endings)

How to build customized screens for Master Data Users

Hi all,
I need to build screens on top of centrally managed master data hub (Data Manager). I want to confirm following
1) Should I go with Guided procedure (CAF) and pre defined Portal contains provided by SAP for MDM?
2) Should I use Java API's provided with SAP MDM.
License is not al all the issue. We have the entire NW components in place. But not sure what to use and what are the advantages/disadv???
Please share your views....
Thx,
R.n

Hi,
I would suggest GP would be easier and in this you can integrate with ur customised objects also.
Vinay

Searching a 100 pin robust connector interface

We have a 100 pin national instrument cable and a corresponding connector on our board. We now search for a more robust connector interface, so the pins don't get damaged when frequently dis- and reconnecting the cable to the board. Anyone knows where to find those 100 pins connector interfaces that might be screwed or securely attached to the PC and the cable ?!?!

I just checked the connector to our serial boards and it does have a fastening screw. I know that some of these connectors (for daq) have a fastening click-clip instead. You can check out, http://www.ni.com/products/ Hope this helps.
-NI support

IPhone dock 30-pin connector to line-out 3.5mm adapter/cable?

Hi folks,
I'm looking for a compact adaptor or cable to go from my iPhone 30-pin connector to a 3.5mm cable (or 3.5mm plug). Wondering if there are any recommendations, as some pre-date the iPhone and thus prompt the iPhone to switch to airport mode...
I've found:
SendStation - Products - PocketDock Line Mini Out USB (I don't need the USB part, but it's handy I guess)
http://www.inspiretech.com/p-483-dock-to-35-auxilary-audio-cable.aspx
IPHONE LINE OUT DOCK W/ 3.5MM JACK (WHITE COLOR) - eBay Other, Audio Cables Connectors, A V Accessories Cables, Electronics. (end time 17-Sep-09 02:25:07 AEST)
ZIP-AUDIO-IP1-B iPod/iPhone Retractable Stereo 3.5mm to iPod/iPhone Dock Connector (White), Apple Mac and iPod Accessories
There are no doubt other (maybe better?) options so look forward to any tips.
Cheers,
B

Did deeper research. It's apparently true that phone call audio is not and cannot be routed to the "line out" of the iPhone. I'm disappointed. It appears to be a hardware design thing, as I've found no app that would enable this, and darned if I can think of a situation that would have this capability as a downside.
tvengr

Dimensions of the 160-Pin Cable for the NI PXI-2530B

Hello,
My mechanical design team wants to know the measurements of the 160-Pin Cable for the NI PXI-2530B. It will be a while before we receive the cable we ordered. I could not find a data sheet with the measurement details; are they? Alternatively, is Figure 1 in the Installation Instructions drawn to scale?: http://www.ni.com/pdf/manuals/375656b.pdf
Thanks!
Solved!
Go to Solution.

JKSH wrote:
Hello,
My mechanical design team wants to know the measurements of the 160-Pin Cable for the NI PXI-2530B. It will be a while before we receive the cable we ordered. I could not find a data sheet with the measurement details; are they? Alternatively, is Figure 1 in the Installation Instructions drawn to scale?: http://www.ni.com/pdf/manuals/375656b.pdf
Thanks!
What dimensions are you looking for?
I'm a little surprised that the length of the cables is not included in the datasheets (I did just look!) - I thought that when I ordered cables for the older-style PXI-2530 modules in my lab that the length was specified in the part description.
If you need the dimensions of the connectors, you can do a little reverse-engineering and identify the dimensions of the various components. The connector to the module is an LFH-160. The Digikey P/N for the body of a connector is WM4099-ND. It may be difficult to find the dimensions of the backshells, however. The 4 terminal block connectors are standard 50-pin D-Subs. There are many examples out whose dimensions you can review.
Jeff
Jeffrey Zola

100-pin Connector Required when Building Custom Cable for PCI-6031E

Similar Messages

Maybe you are looking for