10000: PPPoE session recovery after reload

Hi.
We have seen that there are a feature that recover the PPPoE sessions closed in one side and up in the other. This feature is called 'PPPoE Session Recovery After Reload '.
In the feature navigator, we can see that this feature is available for 7200 series. It seems not available for 10000.
But in the release notes of Cisco IOS 12.3(7)XI3,
http://www.cisco.com/en/US/partner/products/hw/routers/ps133/prod_release_note09186a008040929e.html
appears this bug as resolved:
CSCsa46626
PPP PADT messages are not sent by a PPPoX PTA router to a client when the PPPoX user is no longer connected to the PPPoX PTA router.
This feature is enabled only within the BBA Group configuration using:
bba-group pppoe pppoe1
sessions auto cleanup
This issue can occur when a Cisco 10000 Series router is used as a PPPoX PTA router, and there has been a network flap causing the PPPoX users to lose their connections. PPPoE will experience this issue when BBA Groups are in use. VPDN Group configuration does not support this feature.
There are no known workarounds.
We have tested the IOS 12.3(7)XI6, but the router (10000) doesn't send the PADT (auto cleanup). In 7200, it works correctly.
Anyone have has this problem?
Anyone can confirm if this feature is supported?
Regards.
Jose

Hi Jose ,
I checked it using feature navigator and noticed that cisco 10000 doesn't support ""PPPoE Session Recovery After Reload"" feature.
The following platforms support the feature.
1700
1800
2600
2800
3200
3600
3700
3800
7200
7301
7400
Thanks,
satish

Similar Messages

Newbie : JSP session problem after reload with IE refresh button.

Hi,
I had an issue with JSP reloading using tomcat 4.* and IE.
I have a jsp1.jsp is opened in two different IE windows(one by one). Once i refreshed using IE refresh button from the first window, its loaded with second windows session details. Its changess whole http request object with second window.
Am not sure , why its happening ? Could anybody shed light on this ?
Thanks and Regards
PV

Hello,
No, am not saving any form details . But i noticed session id is changing completely for the first window once i loads frame on the second window.
javascript:alert(document.cookie) Above scriptlet (IE address bar) returns session id from the second window rather than current window without refreshing, that means, its removed whole request completely or somehow manipulated previous sessions. Can anybody explain this behaviour ?
Thanks

ASR9000 multiple PPPoE sessions

Hello all
We try to understand aspects of the behaviour of ASR9K for PPPoE sessions. Specifically we see that after retraining of xDSL CPEs (and for as long as the old session has not been timed out) subsequent PPPoE session initiation attempts from the CPE are denied with the following message
(debug pppoe packet)
pppoe_ma[375]: Packet: [ERROR] Bundle-Ether100.321: Session established cannot re-send PADS for duplicate PADR with host-uniq tag: No error
Does the ASR9K perform any checks based on host-uniq tag to avoid duplicate sessions from same CPE?
Some CPEs after retraining take care of their previous sessions (they clear them - send PADT after retraining) but some others do not for the latter we see this behavior
Thnx

This works for on the ASA, the device works as a PPPoE client:
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a0080ab7ce9.shtml

Problem with Rescue and Recovery after installing Norton Internet Security 2010

Hi all.
It's my first time in this forum.
I have a problem, with Rescue and Recovery, after installing Norton Internet Security 2010 on my T43.
The message I get it:
"Rescue and Recovery is unable to back up the file 'C:\Documents and settings\all Users\Application Data\ Norton\ 00000082\00000109\000003c1\cltMLS1.bat' Because the file is either corrupted or being used by another application. Please close any application that could be using the file.
I tried to close the Norton but I couldn't find how.
Tanks
Doron71

Hi and welcome to the forum,
the reason for this situation is, that the antivir files are protected from being modified.
This is the reason, why this file cannot be backed up. I assume, that you would get much more such messages, as there are surelly multiple files files, that are protected like this.
So the solution is to block folders from being archived. Please start RnR application and in the configuration set this folder as the excluded one.
This will skip the backup of this file and will fix your situation.
Please let me know, if you have covered this.
Cheers

How do i get back my stateful session bean after it has been passivated

hi ,
How do i get back my stateful session bean after it has been passivated by container.
i'm confused that is it possible or not .......give me answer
i've one stateful sessionbean which i'm accessing throgh my normal java client . now what i'm doing is when i first time call a method it is running ......then i'm shutting down the server jboss .......it is calling my ejbPassivate() method ... at this particular time client program doesn't do anything.....
now after i restart my server i'm again calling back that business method with that last object reference.......it gives me the exception given below.....
java.rmi.NoSuchObjectException: no such object in table
java.rmi.NoSuchObjectException: no such object in table
     at sun.rmi.transport.StreamRemoteCall.exceptionReceivedFromServer(Unknown Source)
     at sun.rmi.transport.StreamRemoteCall.executeCall(Unknown Source)
     at sun.rmi.server.UnicastRef.invoke(Unknown Source)
     at org.jboss.invocation.jrmp.server.JRMPInvoker_Stub.invoke(Unknown Source)
     at org.jboss.invocation.jrmp.interfaces.JRMPInvokerProxy.invoke(JRMPInvokerProxy.java:118)
     at org.jboss.invocation.InvokerInterceptor.invokeInvoker(InvokerInterceptor.java:227)
     at org.jboss.invocation.InvokerInterceptor.invoke(InvokerInterceptor.java:167)
     at org.jboss.proxy.TransactionInterceptor.invoke(TransactionInterceptor.java:46)
     at org.jboss.proxy.SecurityInterceptor.invoke(SecurityInterceptor.java:55)
     at org.jboss.proxy.ejb.StatefulSessionInterceptor.invoke(StatefulSessionInterceptor.java:106)
     at org.jboss.proxy.ClientContainer.invoke(ClientContainer.java:86)
     at $Proxy1.makeNewAcc(Unknown Source)
     at client.GanJavaClient.main(GanJavaClient.java:46)so pls tell me that is it possible to get back that session besn or not

Stateful session beans are not persisted across restart of the EJB server instance(s) hosting them. You can't treat a Session bean as one would an entity bean.
Chuck

I am unable to edit information I have typed into a spacebar, this includes backspace, and when I highlight it, even after reloading the page

I recently upgraded to Firefox 4 on my 3 yr old Macbook, though I am unsure if this is in fact connected. Now I am often unable to edit information I have typed into a search bar or text box (such as this one) even after reloading that page or pressing first the back, then the forward buttons. Has anyone else run into this, and does anyone know what is going on?

Start Firefox in [[Safe Mode]] to check if one of the add-ons is causing the problem (switch to the DEFAULT theme: Tools > Add-ons > Appearance/Themes).
* Don't make any changes on the Safe mode start window.
See:
* [[Troubleshooting extensions and themes]]
Create a new profile as a test to check if your current profile is causing the problems.<br />
See [[Basic Troubleshooting#Make_a_new_profile|Basic Troubleshooting: Make a new profile]]
If that new profile works then you can transfer some files from the old profile to that new profile (be careful not to copy corrupted files)
See http://kb.mozillazine.org/Transferring_data_to_a_new_profile_-_Firefox

LMS 4.0.1 software distribution 3 out of 7 fail to pass traffic after reload

I've distributed (7) IOS C3560-ipbasek9-mz.150-1.SE2.bin upgrades on identical 3560G PS-S platform using LMS 4.0.1. All jobs come back successfully completed with the /MD5 hash matching exactly what Cisco has on their website. All devices have sufficient 32MB worth of Flash and verified enough was available prior to distribution.
Issue: After reload 2 of these 3560G devices would not pass traffic. Also, neighboring devices could see these devices through "show cdp neighbors detail" but the management IP was not being displayed. After consoling into these devices via (console port) the management IP address was there but was unable to ping this address locally and neighboring devices were unable to be pinged as well. Performed the "sh run" command and verified the config was correct.
***Cisco's engineers suggestion was to load a lower IOS.***
***I've perused the caveats with this release and have not found any solutions.***
I've already replaced the offending switches with new devices but don't want to keep upgrading with this many failures after reloading.

Your devices with the NX-OS versions you indicate should be OK per the LMS 4.0.1 Supported Devices Table.
Have you updated your LMS with the latest device packages? See the procedure here.

Multicast VPN Extranet Support doesn't work after reload

Hi!
We have Cat6500 with configured Multicast VPN Extranet Support feature. After reload of the 6500 customers in the receive MVPN cannot get mcast stream. We connect test device into source MVPN on that 6500 - everything is OK, mcast stream is available.
Workaround is "no mls ip multicast/mls ip multicast". After these commands mcast in the receive MVPN works fine.
IOS 12.2 SXJ2
Looks like a bug. We have several Cat6500 but only two of them have this issue.
Does anybody faced with such trouble?

Hi!
We have Cat6500 with configured Multicast VPN Extranet Support feature. After reload of the 6500 customers in the receive MVPN cannot get mcast stream. We connect test device into source MVPN on that 6500 - everything is OK, mcast stream is available.
Workaround is "no mls ip multicast/mls ip multicast". After these commands mcast in the receive MVPN works fine.
IOS 12.2 SXJ2
Looks like a bug. We have several Cat6500 but only two of them have this issue.
Does anybody faced with such trouble?

IPhoto will not open even after reload

I have remove iPhoto and reloaded from disc. Still getting the same error message. I am basically pretty frustrated at this point, any ideas?
Interval Since Last Report: 13374 sec
Crashes Since Last Report: 8
Per-App Crashes Since Last Report: 8
Anonymous UUID: 41254D60-DDE4-4A37-A55C-DB4E70D14C3F
Exception Type: EXC_BREAKPOINT (SIGTRAP)
Exception Codes: 0x0000000000000002, 0x0000000000000000
Crashed Thread: 0
Dyld Error Message:
Library not loaded: /System/Library/PrivateFrameworks/iLifeSlideshow.framework/Versions/A/Framework s/iLifeSlideshowProducer.framework/Versions/A/iLifeSlideshowProducer
Referenced from: /System/Library/PrivateFrameworks/iLifeSlideshow.framework/Versions/A/iLifeSlid eshow
Reason: no suitable image found. Did find:
/System/Library/PrivateFrameworks/iLifeSlideshow.framework/Versions/A/Framework s/iLifeSlideshowProducer.framework/Versions/A/iLifeSlideshowProducer:
stat() failed with errno=5=

I am at my wits end with iPhoto error messages and inability to reload it. It has worked fine until yesterday when I started getting the library not loaded error message. I deleted the app, removed the pkg files from HD/Library/Receipts and reloaded the app from my iLife CD as suggested. I have done this 6 times without success and continue to receive the same error message. During reinstall it runs for a long time saying loading packages. After reload there are no new pkg files in teh HD/Library/Receipts location. I do not know what to do next . . . I am open to any assistance.

Anyway to recover photos on a iPhone 4s after reload of os?

Anyway to recover photos on a iPhone 4s after reload of os?

Only from your backup if you have any.

Simplify recovery after opening the database with the RESETLOGS option

Hi All,
I just have doubt ,regarding the topic which is given in Oracle 11g Exam Syllabus for upgrading from 9i to 11g OCP.The opic is
*"Simplify recovery after opening the database with the RESETLOGS option"* in this topic what one need to study.
As i am little bit confuse related to "Recovery through RESETLOGS and reset of the incarnation of the database".
Kindly correct me if i am wrong
Thanks in advance

vk82 wrote:
Hi All,
I just have doubt ,regarding the topic which is given in Oracle 11g Exam Syllabus for upgrading from 9i to 11g OCP.The opic is
*"Simplify recovery after opening the database with the RESETLOGS option"* in this topic what one need to study.
As i am little bit confuse related to "Recovery through RESETLOGS and reset of the incarnation of the database".
Kindly correct me if i am wrong
Thanks in advanceyou are correct so you can mark this thread as answered
Handle:     vk82
Status Level:     Newbie (35)
Registered:     Nov 21, 2010
Total Posts:     733
Total Questions:     180 (115 unresolved)

After reloading adobe creative suite cs3 on my mac 10.4.11 acrobat will not open any pdfs it previously opened. help!

after reloading adobe creative suite cs3 on my mac 10.4.11 acrobat will not open any pdfs it previously opened. help!

hello.   hey, thanks very much for writing back. i got some good info with a search or two. (info about what regedit is and what corresponds to it in OS X -- regedit allows you to edit "preference" keys for individual programs, OSX's equivalent for these keys are the .plists in User & System: Preferences and Application Support)
what i ended up doing was uninstalling Premiere Pro (not the suite, just PPro).   Then i deleted a few preference files:
from User /Preferences/Adobe:
com.adobe.AdobePremierePro.plist
com.Adobe.Premiere Pro.5.0.plist
and from System Preferences:
the file: Adobe Premiere Pro Prefs
and..
/.../Premiere Pro/5.0/...
AMEPrefs.xml     (i noticed that there's also a preference file in Media Encoder's own folder so i didn't sweat this one)
Debug Database.txt
Placeholder Preset.epr
PostEncodeCmds.pref
PresetCache.xml
Trace Database.txt
NOTE:
of course i don't know if deleting any files beyond the 2 .plist files in User Prefs was necessary, but... it seems to have worked.
I then reinstalled Premiere Pro CS5, and fired up an old project and i've got playback of HD and DV files, and snappy editing and rendering, so hopefully i'm good to go.   I'm just going to stick with v5.0.0 because i actually don't remember ever having any trouble with it, and i don't remember v5.0.4 adding anything i was 'missing' or 'needed'
hopefully, this thread will be useful for any future folks that run into trouble - and it's got a solution for both Windows and OS X
happy editing,
peace

After reloading a website its page is not active.

After reloading a website the page is not active. I have to click on a different program, minimize and restore, or click on the windows task bar and then things are able to be clicked on and pointer is recognized. All sites are affected
== URL of affected sites ==
http://ALL SITES
== User Agent ==
Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US) AppleWebKit/533.16 (KHTML, like Gecko) Version/5.0 Safari/533.16

Hi ,
According to your description, my understanding is that you got an error when you clicked the link to a library.
Whether you customize the library page.
Please check Recycle Bin on your site, see whether there is the library in it. If yes, restore the library, then compare the result.
If this issue still exists, please find more information about this issue in the logging file, the path is C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\14\LOGS.
I hope this helps.
Thanks,
Wendy
Wendy Li
TechNet Community Support

CX Module failed after reload

Hi there!
I do know if it is some kind of bug, but all the time after reload the CX module all things stop work, regardless of what form do I reset the module.
I already tried to acccess the module and reload, tried to stop services with "services stop" command and after that "reload", tried to shutdown using ASA commands and reload it from ASA... everytime I reload when the module come back all services start perfectly, like example below:
spcx02>show services status
============================================================
Process           | PID   | Up    | Up Time
============================================================
AD Interface      | 6284 | True | 05:03:03
Message Nameserver| 6022 | True | 05:03:59
HTTP Auth Daemon | 6094 | True | 05:03:58
PDTS              | 6073 | True | 05:03:59
HTTP Inspector    | 6193 | True | 05:03:37
HTTP Server       | 5972 | True | 05:03:59
Data Plane        | 6270 | True | 05:03:06
Management Plane | 6115 | True | 05:03:45
HPM Monitor       | 6289 | True | 05:03:03
Updater           | 6399 | True | 05:02:52
Card Manager      | 5930 | True | 05:03:59
ARP Daemon        | 6089 | True | 05:03:58
Event Server      | 6133 | True | 05:03:41
TLS Proxy         | 6204 | True | 05:03:37
============================================================
spcx02>show ver
Cisco ASA CX Platform 9.1.2 (42)
Cisco Prime Security Manager 9.1.2 (42) for spcx02 firewall
spcx02>
I even can access the GUI using my browser, but all athentication with CDA or AD that before boot was working correctly show up the error:
"Connection failed with error: Could not connect to virtual directory interface."
Everytime I reload I must reinstall the entire module and reconfigure everything. Anyone know if this is a bug that crashes the database or something like this?
Regards,
Rodrigo Alves

Ah, I forgot to write down that after reload the module and it come back it stop all traffic passing through the firewall and I must remove the policy-map configuration:
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect rsh
inspect rtsp
inspect sqlnet
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
inspect h323 h225
inspect h323 ras
inspect skinny
class class-default
cxsc fail-open auth-proxy

Firefox freezes (along with any other program I might have running) a minute or two after I have started my session. After a minute or so, it's O.K.

Firefox freezes (along with any other program I might have running) a minute or two after I have started my session. After a minute or so, it's O.K. I have disabled all off my extensions and the problem still persists.

Hello Meg, the phone allowed me to stay on long enough to download a new app but then shut down the app centre and returned to the home screen.
Was there a specific "fix App" for this?

10000: PPPoE session recovery after reload

Similar Messages

Maybe you are looking for