1130AG AP Issue

I have serveral 1130AG AP that when they are configured to use LWAPP all of my Motorola Handheld scanners connect to the SSIDs fine.
When I have some that are on Autonomous then the scanners will not connect at all.
I have upgraded a test 1130AG to the lates IOS and that does not help.
Any suggestions.

This is the WLAN config on the WLC that I need to use.
WLAN Identifier.................................. 4
Profile Name..................................... WIFIGUEST
Network Name (SSID).............................. PRIVATE
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
  Client Profiling Status ....................... Disabled
  Radius-NAC State............................... Disabled
  SNMP-NAC State................................. Disabled
  Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Maximum number of Clients per AP Radio........... 200
Number of Active Clients......................... 38
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ wifi
--More-- or (q)uit
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
DHCP Server...................................... Default
DHCP Address Assignment Required................. Disabled
Static IP client tunneling....................... Disabled
Quality of Service............................... Silver
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
--More-- or (q)uit
   Authentication................................ Global Servers
   Accounting.................................... Global Servers
      Interim Update............................. Disabled
   Dynamic Interface............................. Disabled
Local EAP Authentication......................... Disabled
Security
   802.11 Authentication:........................ Open System
   FT Support.................................... Disabled
   Static WEP Keys............................... Disabled
   802.1X........................................ Disabled
   Wi-Fi Protected Access (WPA/WPA2)............. Disabled
   Wi-Fi Direct policy configured................ Disabled
   EAP-Passthrough............................... Disabled
   CKIP ......................................... Disabled
   Web Based Authentication...................... Disabled
   Web-Passthrough............................... Disabled
   Conditional Web Redirect...................... Disabled
   Splash-Page Web Redirect...................... Disabled
   Auto Anchor................................... Disabled
   FlexConnect Local Switching................... Disabled
   FlexConnect Local Authentication.............. Disabled
   FlexConnect Learn IP Address.................. Enabled
--More-- or (q)uit
   Client MFP.................................... Optional but inactive (WPA2 not configured)
   Tkip MIC Countermeasure Hold-down Timer....... 60
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Enabled
SIP CAC Fail Send Dis-Association Policy......... Disabled
KTS based CAC Policy............................. Disabled
Band Select...................................... Disabled
Load Balancing................................... Disabled
Multicast Buffer................................. Disabled
Mobility Anchor List
WLAN ID     IP Address            Status
802.11u........................................ Disabled
  Access Network type............................ Not configured
  Network Authentication type.................... Not configured
  Internet service............................... Disabled
  HESSID......................................... 00:00:00:00:00:00
Hotspot 2.0.................................... Disabled

Similar Messages

  • Aironet 1130ag RAIDUS auth issues - what is no sg in radius-timers?

    Hi All.
    wonder if anyone can help
    We have an aironet 1130ag in a remote office connected to the data centre over MPLS. The Radius server is based on server 2003
    We have hundreds of these points set up exactly the same but this is the only one giving me issues, I even stripped the config and rebuilt it and then swapped with a new access point
    The issue is that clients can't authenticate when connecting to the access point but provides nothing in event viewer. Checking the RADIUs server provides nothing either.
    The access point error logs just state station: authentication failed
    On looking deeper into the problem I enabled RADIUS debugging on the access point and got some interesting results, in particular is the line:
    no sg in radius-timers: ctx 0x12EF0A4 sg 0x0000
    I can't find out what no SG in Radius-timers actually means, but after that line appears I just see more retransmits and no sg fails.
    I inspected the packets on the RADIUs server and found lots access requests coming from my access point and lots of access-challenges returning back from my RADIUS server - I'm not sure how often that's supposed to happen or if it's a one time occurance. I did however see directly after the first access-request that the RADIUS server returns with UDP and is fragmented, length is 1514...... could this be the problem? If so why cannot it hanlde fragmented packets? And what do I need to do to fix?
    Many thanks for the help
    Mark

    the fragmented packet might be a red herring as I've just done the same packet inspection on the same radius server but coming from a different access point which works, I get the same fragmented UDP packet but the connection works.
    any ideas?

  • 1130AG Won't Hold Time And Date After A Reload

    Hello - I am currently deploying 1130AG standalone access points to all my locations. I am having trouble getting them to consistantly authenticate against AD using RADIUS and PEAP. I have noticed that all the access points revert back to a date in 2001 or 2002 after every reboot. So, first, after I issue the clock set command and fix the time and save it, how do I get it to hold that after a reboot. And second, could the time/date mismatch be causing a problem with authentication? Here is a typical config that I am using:
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    service password-encryption
    hostname S064AP
    enable secret XX
    aaa new-model
    aaa group server radius rad_eap
    server 10.0.64.10 auth-port 1645 acct-port 1646
    aaa group server radius rad_mac
    aaa group server radius rad_acct
    aaa group server radius rad_admin
    aaa group server tacacs+ tac_admin
    aaa group server radius rad_pmip
    aaa group server radius dummy
    aaa authentication login eap_methods group rad_eap
    aaa authentication login mac_methods local
    aaa authorization exec default local
    aaa accounting network acct_methods start-stop group rad_acct
    aaa session-id common
    ip name-server 10.0.64.10
    dot11 ssid S064WLAN
    authentication open eap eap_methods
    authentication network-eap eap_methods
    authentication key-management wpa
    guest-mode
    infrastructure-ssid optional
    power inline negotiation prestandard source
    username admin password XX
    username Cisco privilege 15 password XX
    bridge irb
    interface Dot11Radio0
    no ip address
    no ip route-cache
    encryption mode ciphers tkip
    ssid S064WLAN
    station-role root
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    interface Dot11Radio1
    no ip address
    no ip route-cache
    shutdown
    dfs band 3 block
    channel dfs
    station-role root
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    interface FastEthernet0
    no ip address
    no ip route-cache
    duplex auto
    speed auto
    bridge-group 1
    no bridge-group 1 source-learning
    bridge-group 1 spanning-disabled
    interface BVI1
    ip address 10.0.64.205 255.255.255.0
    no ip route-cache
    ip default-gateway 10.0.64.1
    ip http server
    no ip http secure-server
    ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
    ip radius source-interface BVI1
    snmp-server community XX RW
    radius-server host 10.0.64.10 auth-port 1645 acct-port 1646 key XX
    bridge 1 route ip
    line con 0
    line vty 0 4
    end

    You can enable SNTP to synchronize your clock.
    Command: sntp server

  • LWAPP 1130AG constantly associating and disassociating

    Hi,
    I have inherited a LWAPP system with around 40 1130AGs and a single 4400 WLC which all work fine.
    I attempted to upgrade a 1130 Autonomous to LWAPP and it said it worked using the upgrade tool and c1130-rcvk9w8-tar.123-11JX1 image.
    I checked the WLC and initially could see that the WAP was downloading the image from the WLC, but since then it constantly says this on the WLC:
    AP Disassociated. Base Radio MAC:*************
    AP Associated. Base Radio MAC: *****************
    I have done debug lwapp events enable on the WLC and all it says regarding the WAP is:
    Tue Jul 14 13:22:20 2009: ************* Received LWAPP DISCOVERY REQUEST from AP ************** to ff:ff:ff:ff:ff:ff on port '2'
    And that's it. Nothing else.
    I've added the Mac address into the WLC AP Authorization list as a MIC.
    I'm trying to get the public key hash using debug pm pki enable using Putty, but when I put in this command, it logs a huge amount of stuff and then Putty simply closes, without logging the needed info. Is there any other way to get this, or stop the session from closing?
    Any ideas on getting the 1130AG working?

    Sounds like you have a duplicate IP address issue. If the AP is associating to the WLC and then a duplicate address is dicovered the AP will temporarily lose IP connectivity, pick up the same IP address again and keep going round in circles.
    How is the AP obtaining its IP address? If you are using a server check the leases and exclude any static addresses issued. If you are using the WLC DHCP server be careful as they aren't intelligent enough to discover conflicts.
    If all else fails do a port span of the WLC uplink and post the trace. If you see the AP transmitting LWAPP traffic to the AP manager, then after a minute it is doing a DHCP Discover then it is defintely IP conflicts.
    You can also configure the AP with a known unused static IP address with the command 'lwapp ap ip address x.x.x.x x.x.x.x'

  • WDS and Roaming with 1130AG APs

    Hi there,
    I was wondering if someone could provide me with some insight into a configuration scenario i'm facing:
    Our office is situated in an old building and as such , wireless range is an issue as the walls are very thick and we have a mixture of clients from Laptops to android devices to iPhones that require access.
    we have 2 goals (first 2 are more important)
    1. to be able to roam anywhere in the building and pickup the wireless (fast roaming isn't really that necessary as voice isn't utilised)
    2. to have only 1 SSID for corporate access - Corp VLAN
    3. to have an SSID for guests to access - Guest VLAN
    The VLANs aren't an issue, i have an 1130AG setup which already has 2 SSIDs which does what i need.
    My main concern is around roaming, and i've read a lot about WDS, but this needs an external radius server, i've seen the articles that describe how to set up an AP as WDS and then add Infrastructure APs
    I've also seen that you can simply configure each AP exactly the same, but with different channells.
    I have 4 1130AGs at my disposal.
    What would you guys suggest is my best solution?
    Any help would be gratefully received.

    To get the best roaming, you need to make sure you have enough coverage. That usually means a good site survey was performed to specify how many access points and the locations of the access point. Without this piece, there is no guarantee of roaming.
    As far as WDS, you can setup an autonomous ap as a WDS server that is either dedicated as a WDS or is a WDS server and also serves clients.
    Sent from Cisco Technical Support iPhone App

  • Windows 7 problem connecting to Aironet 1130AG AP

    We currently have Windows XP Pro laptops that are configured to connect  with our Cisco Aironet 1130AG Access Point and everything works fine.  I am  trying to configure new Windows 7 laptops using the same settings we  used for the XP Pro laptops and they will not connect to the AP.  Have any of  you run into configuration issues with Windows 7 and Cisco wireless access point connectivity  and found a solution?  Is there any documenation on how to configure Windows 7 with Cisco Aironet 1130AG Access Points?

    The wireless card is a Dell DW1501 wireless N WLAN Half Mini Card (Broadcom is the manufacturer).
    I had the router setup to not broadcast.  I changed it to broadcast and Windows  7 still will not connect.  Do you have any other suggestions?  Windows 7 is  32-bit on the laptops and I read somewhere online that mentioned they had  the same problems with 32-bit but not 64-bit.  The XP laptops wireless  configuration is WPA-Enterprise with Cisco Leap along with user name and  password.

  • POE on Aironet 1130ag failes

    Hi, I am trying to enable POE on our three new Aironet 1130ag but they fail to get the power from 6500 switches which have WS-X6348 modules and WS-F6K-VPWR sub modules. I disabled power injector and tried power negotiation and pre-standard compatibility without any success. Thanks.

    Hi Reza,
    I think you have already figured out the problem here :) This module - WS-F6K-VPWR only supplies 7W of PoE power and the 1130 requires 802.3af 15W PoE;
    http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_10826.html#wp31976
    We had this happen to us recently due to a PoE problem. The 1130 requires either IEEE 802.3af power or needs a setting on the WLC for using power injector or Cisco Pre-Standard PoE. Our older switches could only provide Cisco Pre-Standard PoE so we had to tweak the WLC Power setting for these AP's. Once we did that the Radios came right up. Here is a reference;
    You may have to enter the following info in the WLC;
    While the AP boots, with its Intelligent Power Management feature, it negotiates with the switch via Cisco Discovery Protocol messages in order to provide the necessary power to the AP. Even though the power injector is connected to the AP, the AP that uses this Intelligent Power Management feature gives priority to the Cisco Discovery Protocol information in order to identify whether or not the switch can provide the power. Therefore, after the Cisco Discovery Protocol message shows that the switch does not provide sufficient power (since it is not an inline power capable switch), the AP disables its radios. At this time, the status LED of the AP turns orange and this error message is recorded:
    [ERROR] : AP has not enough in-line power
    to enable radio slot 1 In order to overcome this problem, issue the
    config ap power injector enable installed
    command on the controller that is connected with this AP. This command is available from controller version 3.2.116.21. Ensure that you use the correct version in the controller.
    This command specifies that a power injector is used in order to supply sufficient power to the AP.
    From this doc;
    Cisco Aironet and WLAN Controller Product Power Options
    http://www.cisco.com/en/US/products/hw/wireless/ps430/products_tech_note09186a00800946e7.sh
    Have a look at this good Q&A;
    Q. As with the 1200 Series AP, can a 1130/1240 AP work with 7 watts of power to it from a pre-standard POE with 802.11g radio alone disabled?
    A. No, the power consumption on the AP1240 breaks down like this:
    5 GHz only radio 11.56 watts
    2.4 GHz only radio 12.96 watts
    Both radios on 15.0 watts
    The power consumption on the AP1130 breaks down like this:
    5 GHz only radio 9.750 watts
    2.4 GHz only radio 9.910 watts
    Both radios on 12.20 watts
    In either case, you can see that, for the AP to operate with a single radio, it requires more than 7 watts of power.
    http://www.cisco.com/en/US/products/hw/wireless/ps430/products_qanda_item09186a00806a4da3.shtml
    Hope this helps!
    Rob

  • POE from 3524PWR Switch for 1130AG AP?

    We have a bunch of 1130AG LWAPP access points that we are installing in various locations. Those locations with newer 802.3af switches such as the 3750's and 3560's power the AP's without issue. However we have mixed results plugging them in to older Cisco POE only 3524PWR Switches.
    For the most part if we plug the 1130AG's into the 3524PWR's with short patch cords they power the radios up. However, if we connect them to a longer network line (80 to 100 feet) they disable the radios and WCS alarms tell me that the switch could not supply enough power for the radios.
    The Quick Start Guide (page 14) shows the 1130AG supporting both Cisco POE and 802.3af power. Is there any way to get these to reliable power up on 3524PWR switches or do I need to use power cords or power injectors?

    Hi Jim,
    We had this happen to us due to the same PoE problem. The 1130 requires either IEEE 802.3af power **or needs a setting on the WLC for using power injector or Cisco Pre-Standard PoE. Our older switches could only provide Cisco Pre-Standard PoE so we had to tweak the WLC Power setting for these AP's. Once we did that the Radios came right up. Here is a reference;
    You may have to enter the following info in the WLC;
    While the AP boots, with its Intelligent Power Management feature, it negotiates with the switch via Cisco Discovery Protocol messages in order to provide the necessary power to the AP. Even though the power injector is connected to the AP, the AP that uses this Intelligent Power Management feature gives priority to the Cisco Discovery Protocol information in order to identify whether or not the switch can provide the power. Therefore, after the Cisco Discovery Protocol message shows that the switch does not provide sufficient power (since it is not an inline power capable switch), the AP disables its radios. At this time, the status LED of the AP turns orange and this error message is recorded:
    [ERROR] : AP has not enough in-line power
    to enable radio slot 1 In order to overcome this problem, issue the
    config ap power injector enable installed
    command on the controller that is connected with this AP. This command is available from controller version 3.2.116.21. Ensure that you use the correct version in the controller.
    This command specifies that a power injector is used in order to supply sufficient power to the AP.
    From this doc;
    Cisco Aironet and WLAN Controller Product Power Options
    http://www.cisco.com/en/US/products/hw/wireless/ps430/products_tech_note09186a00800946e7.shtml
    Hope this helps!
    Rob

  • Pulling image from 1130AG

    Hi all. I have a couple 1130AG switches.  I'm trying to pull an image file from the flash on a Cisco Air AP1131AG.  The file is
    c1130-k9w8-mx.124-23c.JA4.tar.  The issue that I'm seeing is, I do not see a copy command to go through the tftp process.  I've tried to use tftpd32 and enter the IP of the AP as the remote host, but that is not working either.  Do I need to connect an ethernet cable straight to the AP in order to use Tftpd32, or can I use a console cable? 
    Any help is much appreciated.
    Thanks
    Jason

    Thanks for your response.
    I got an image (it wasn't the exact same but I thought I would try it). I've tftp'd the file over to the AP, and added "boot system %filename%" to the running config and saved it. I then did a reload.  when the new image tries to load, I get a "Permission Denied".  The file has rwx as it's file permissions so I'm a little confused as to why the permissions would be wrong.

  • MBSSID Issue

    I have several 1130AG LWAPP's running 12.4(13d)JA connected to a contoller running 5.0.148.
    2 SSID's are broadcast - usually no problem.
    However, I've noticed that several different vendor wireless cards cannot see both SSID's.
    Running a wireless capture, I can see that in reply to my probe request, I receive 2 probe responses. The only difference between the two 802.11 frame bodies is that for the SSID that I cannot see there is extended channel switch announcement (ECSA) information.
    I'm slight confused as 1.) The SSID's are on the same antenna so shouldn't ECSA be on both beacon reponses? 2.) ECSA profile on 802.11b/g is wmm - wmm is disable both WLAN's.

    I'm not sure changing Auto RF will make much difference. The Power and Channel settings are fine.
    We use WZC.
    I can solve the issue by upgrading internal users drivers. Specifically Intel 4965AG driver 11.1 to 11.5 - but the release notes don't imply any changes that are related to my problem and I'm reluctant to force this on 300+ people without a solid conclusion.
    However I have no control over external guests WIFI drivers. So far its been a 50-50 hit/miss of them seeing the 2nd SSID (our GUEST ssid).
    I'm sure its an 11n option but they are def. disabled on the WLC.

  • Trouble getting 1130AG LWAPP to Connect to Controller

    I'm having trouble getting any of my 1130AG LWAPPs to connect to my WLC.
    I have not configured my DHCP server to deliver option 43 or option 60.
    However, I have manually configured the LWAPP using the CLI. I have assigned a static IP address, the default-gateway, gave it a hostname, and gave it the controller ip address.
    When I issue the command:
    show lwapp ip config
    all of the information appears correctly.
    However, the controller never registers the LWAPP.
    This is a completely new setup, so there are no previous configs to contend with.
    If I issue the command on the LWAPP:
    debug lwapp client event
    Two debug messages appear consistently every 3-5 seconds. They are:
    *Mar 1 00:34:26.733: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
    *Mar 1 00:34:36.733: LWAPP_CLIENT_EVENT: spamHandleDiscoveryTimer: Could not discover any MWAR
    Any suggestions?
    ~ Vance R. Gregory

    You have to put option 43 in hexadecimal no. below you will find an example of DHCP configurations on router that act as a DHCP for LWAPP in different network:
    ip dhcp excluded-address 172.16.1.1 192.168.1.1
    ip dhcp pool WAP_DHCP_SCOPE
    network 192.168.1.0 255.255.255.0
    option 43 hex f104c0a814f0
    The hex string is assembled by concatenating the TLV values shown below:
    Type + Length + Value
    Type is always f1(hex). Length is the number of controller management IP addresses times 4 in hex. Value is the IP address of the controller listed sequentially in hex.
    WLC IP is 192.168.20.240 f1+1*4+ac10.14f0 = f104c0a814f0
    default-router 192.168.1.1

  • New DVR Issues (First Run, Channel Switching, etc.)

    I've spent the last 30 minutes trying to find answers through the search with no luck, so sorry if I missed something.
    I recently switched to FIOS from RCN cable in New York.  I've gone through trying to setup my DVR and am running into issues and was hoping for some answers.
    1.  I setup two programs to record at 8PM, I was watching another channel at the time and only half paying attention.  Around 8:02 I noticed a message had popped up asking if I would like to switch channels to start recording.  I was expecting it to force it to switch like my old DVR, but in this case it didn't switch and I missed the first two minutes of one of the shows.  I typically leave my DVR on all day and just turn off the TV, this dual show handling will cause issues with that if I forget to turn off the DVR.  Is there a setting I can change that will force the DVR to choose one of the recording channels?
    2.  I setup all my recordings for "First Run" because I only want to see the new episodes.  One show I setup was The Daily Show on comedy central, which is shown weeknights at 11pm and repeated 3-4 times throughout the day.  My scheduled recordings is showing all these as planned recordings even though only the 11pm show is really "new".  Most of the shows I've setup are once a week so they aren't a problem, but this seems like it will quickly fill my DVR.  Any fixes?
    Thanks for the help.
    Solved!
    Go to Solution.

    I came from RCN about a year ago.  Fios is different in several ways, not all of them desirable.  Here are several ways to get--and fix--unwanted recordings from a series recording setup.
    Some general principles. 
    Saving changes.  When you originally create a series with options, or if you go back to edit the options for an existing series, You MUST save the Series Options changes.  Pretty much everywhere else in the user interface, when you change an option, the change takes effect immediately--but not in Series Options.  Look at the Series Options window.  Look at the far right side.  There is a vertical "Save" bar, which you must navigate to and click OK on to actually save your changes.  Exiting the Series Options window without having first saved your changes loses all your attempted changes--immediately.
    Default Series Options.  This is accessed  from [Menu]--DVR--Settings--Default Series Options.  This will bring up the series options that will automatically be applied to the creation of a NEW series. The options for every previously created series will not be affected by a subsequent modification of the Default Series Options.  You should set these options to the way you would like them to be for the majority of series recordings that you are likely to create.  Be sure to SAVE your changes.  This is what you will get when you select "Create Series Recording" from the Guide.  When creating a new series recording where you think that you may want options different from the default, select "Create Series with Options" instead.  Series Options can always be changed for any individual series set up later--but not for all series at once.
    Non-series recordings.  With Fios you have no directly available options for these.  With RCN and most other DVRs, you can change the start and end times for individual episodes, including individual episodes that are also in a series.  With Fios, your workarounds are to create a series with options for a single program, then delete the series later;  change the series options if the program is already in a series, then undo the changes you made to the series options later; or schedule recordings of the preceding and/or following shows as needed.
    And now, to the unwanted repeats. 
    First, make sure your series options for the specific series in question--and not just the series default options--include "First Run Only".  If not, fix that and SAVE.  Then check you results by viewing the current options using the Series Manager app under the DVR menu.
    Second, and most annoying, the Guide can have repeat programs on your channel tagged as "New".  It happens.  Set the series option "Air Time" to "Selected Time".  To make this work correctly, you must have set up the original series recording after selecting the program in the Guide at the exact time of a first run showing (11pm, in your case), and not on a repeat entry in the Guide.  Then, even it The Daily Show is tagged as New for repeat showings, these will be ignored. 
    Third, another channel may air reruns of the program in your series recording, and the first showing of a rerun episode on the other channel may be tagged as "New".  These can be ignored in your series if you set the series option "Channel" to "Selected Channel".  Related to this, if there is both an SD and HD channel broadcasting you series program, you will record them both if the series option "Duplicates" is set to "Yes".  However, when the Channel option is set to "Selected Channel", the Duplicates Option is always effectively "No", regardless of what shows up on the options screen.  
    As for you missing two minutes,  I have sereral instances in which two programs start recording at the same time.  To the best of my recollection, whenever the warning message has appeared, ignoring it has not caused a loss of recording time.  You might have an older software version.  Newest is v.1.8.  Look at Menu--Settings--System Info.  Or, I might not have noticed the loss of minutes.  I regularly see up to a minute of previous programming at the start of a recording, or a few missing seconds at the beginning or end of a recording.  There are a lot of possibilities for that, but the DVR clock being incorrect is not one of them.  With RCN, the DVR clocks occasionally drifted off by as much as a minute and a half.

  • Pension issue Mid Month Leaving

    Dear All,
    As per rule sustem should deduct mid month joining/leaving/absences or transfer scenarios, the Pension/PF Basis will be correspondingly prorated. But our system is not doing this. In RT table i have found 3FC Pension Basis for Er c 01/2010                    0.00           6,500.00.
    Employee leaving date is 14.04.2010. system is picking pension amout as 541. Last year it was coming right.
    Please suggest.
    Ashwani

    Dear Jayanti,
    We required prorata basis pension in case of left employees and system is not doing this. This is the issue. As per our PF experts Pension amount should come on prorata basis for left employees in case they left mid of month.System is doing prorata basis last year but from this year it is deducting 541. I am giving two RT cases of different years.
    RT table for year 2010. DOL 26.04.2010
    /111 EPF Basis              01/2010                    0.00           8,750.00 
    /139 VPF Basis              01/2010                    0.00           8,750.00 
    /3F1 Ee PF contribution     01/2010                    0.00           1,050.00 
    /3F3 Er PF contribution     01/2010                    0.00             509.00 
    /3F5 Ee Mon PF contribution 01/2010                    0.00           1,050.00 
    /3F6 Ee Ann PF contribution 01/2010                    0.00          12,600.00 
    /3F9 PF adm chrgs * 1,00,00 01/2010                    0.00              96.25 
    /3FA PF basis for Ee contri 01/2010                    0.00           8,750.00 
    /3FB PF Basis for Er Contri 01/2010                    0.00           8,750.00 
    /3FJ VPF basis for Ee contr 01/2010                    0.00           8,750.00 
    /3FL PF Basis for Er Contri 01/2010                    0.00           6,500.00 
    /3F4 Er Pension contributio 01/2010                    0.00             541.00
    /3FC Pension Basis for Er c 01/2010                    0.00           6,500.00
    /3FB PF Basis for Er Contri 01/2010                    0.00           8,750.00
    /3FC Pension Basis for Er c 01/2010                    0.00           6,500.00
    /3FJ VPF basis for Ee contr 01/2010                    0.00           8,750.00
    /3FL PF Basis for Er Contri 01/2010                    0.00           6,500.00
    /3R3 Metro HRA Basis Amount 01/2010                    0.00           8,750.00
    1BAS Basic Salary           01/2010                    0.00           8,750.00
    RT table for year 2009. DOL 27.10.2009
                                                                                    /111 EPF Basis              07/2009                    0.00           9,016.13
    /139 VPF Basis              07/2009                    0.00           9,016.13
    /3F1 Ee PF contribution     07/2009                    0.00           1,082.00
    /3F3 Er PF contribution     07/2009                    0.00             628.00
    /3F5 Ee Mon PF contribution 07/2009                    0.00           1,082.00
    /3F6 Ee Ann PF contribution 07/2009                    0.00           8,822.00
    /3F9 PF adm chrgs * 1,00,00 07/2009                    0.00              99.18
    /3FA PF basis for Ee contri 07/2009                    0.00           9,016.00
    /3FB PF Basis for Er Contri 07/2009                    0.00           9,016.00
    /3FJ VPF basis for Ee contr 07/2009                    0.00           9,016.00
    /3FL PF Basis for Er Contri 07/2009                    0.00           5,452.00
    /3FB PF Basis for Er Contri 07/2009                    0.00           9,016.00 
    /3FC Pension Basis for Er c 07/2009                    0.00           5,452.00 
    /3FJ VPF basis for Ee contr 07/2009                    0.00           9,016.00 
    /3FL PF Basis for Er Contri 07/2009                    0.00           5,452.00 
    /3R4 Non-metro HRA Basis Am 07/2009                    0.00           9,016.13 
    1BAS Basic Salary           07/2009                    0.00           9,016.13 
    Now please suggest what to do. where is the problem  ? If have also checked EXIT_HINCALC0_002 but nothing written in it.
    With Regards
    Ashwani

  • Open PO Analysis - BW report issue

    Hello Friends
    I constructed a query in BW in order to show Open Purchase Orders. We have custom DSO populated with standard
    datasource 2lis_02_itm (Purcahse Order Item). In this DSO we mapped the field ELIKZ to the infoobject 0COMP_DEL
    (Delivery completed).
    We loaded the data from ECC system for all POs and found the following issue for Stock Transport Purchase orders (DocType = UB).
    We have a PO with 4 line items. For line items 10 and 20, Goods issued, Goods received and both the flags "Delivery
    complete" and "Final delivery" checked. For line items 30 and 40, only delivery indicator note is issued for zero
    quantity and Delivery complete flag is checked (Final delivery flag is not checked) in ECC system. For this PO, the
    delivery completion indicator is not properly updated in the DSO for line items 30 and 40. The data looks like the
    following:
    DOC_NUM     DOC_ITEM       DOCTYPE     COMP_DEL
    650000001       10     UB        X
    650000001       20     UB        X
    650000001       30     UB
    650000001       40     UB      
    When we run the Open PO analysis report on BW side this PO is appearing in the report but the same is closed in ECC
    system.
    Any help is appreciated in this regard.
    Thanks and Regards
    sampath

    Hi Priya and Reddy
       Thanks for your response.
                         Yes the indicator is checked in EKPO table for items 30 and 40 and delta is running regularly for more than 1 year and no issues with other POs. This is happening only for few POs of type Stock Transport (UB).
                        I already checked the changes in ME23N and the Delivery completed indicator was changed and it reflected in EKPO table. Further, i checked the PSA records for this PO and i am getting the records with the Delivery completed flag but when i update from PSA to DSO the delivery completed indicator is not updating properly.
                       In PSA, for item 30 i have the following entries. Record number 42 is capturing the value X for ELIKZ but after that i am getting two more records 43 and 44 with process key 10 and without X for ELIKZ. I think this is causing the problem.
    Record No.    Doc.No.                    Item              Processkey         Rocancel     Elikz
        41               6500000001            30                    11                            X           ---    
        42               6500000001            30                    11                            ---           X
        43               6500000001            30                    10                            X           ---
        44               6500000001            30                    10                            ---         ---
    (Here --- means blank)        
    Thanks and Regards
    sampath

  • HP LaserJet Enterprise 600 M602 driver issue

    Hello,
    I've got issue with 600-series printers. We use the latest UPD drivrer ver. 61.175.1.18849 and print from XenApp 6.5. The error occurs every time when users try to print jpg files from XenApp session. It only happens with 600 series printers and UPD.
    Also I've tried to assign native 600-series driver ver. 6.3.9600.16384 and it works good. But with that driver system says that it's color printer and it brokes our printing reports. These reports are very important for us. So we can't use printer and that driver as well.
    Printer installed on Windows Server 2012 R2. All clients are Windows 7 x64. XenApp Servers are Server 2008R2.
    Is it possible to get fixed UPD driver or correct native driver for Server 2012 R2?
    Regards,
    Anatoly

    I am sorry, but to get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial printer. You can do this at Printers - LaserJet.
    Click on New Post.
    I hope this helps.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

Maybe you are looking for

  • Adobe Muse update discrepancy

    I'm working on a Muse file (I'm a Creative Cloud subscriber) and some of the features on a Terry White tutorial (ie. parallax scrolling) are not available on my Muse. The Adobe application manager tells me that my version is up to date. What's up?

  • Reg. Invalid batch according to selection criteria in batch determination

    Dear Experts I have configured newly batch management in our IDES ECC 6 system in which while posting the GRN I am getting the following error: Invalid batch according to selection criteria in batch determination Batch WHITE has already been posted i

  • Iphone 5s from UAE enable FaceTime outside UAE

    Hi, I have bought my iPhone 5s contract free  in UAE (Dubai) but im from Europe. I came back home now and i cant re enable FaceTime, altho app store worker over there told me that it was possible, but forgot to ask him HOW Can you help me ? Thanks in

  • Songs not playing in entirty

    I have experieced this for quite some time, and it's really annoying.  Some songs will play about half way through then some other random song will start playing.  The album art, name, etc still show the original song, but it's not that song that's p

  • DV4 keeps showing recovery manager even in safe mode

    Hello everyone, i have a hp pavilion dv4 with windows7 64 bit intel core i5. It had been going well until last month. After I did several shut downs I ended up with a problem. Whenever I start up the computer HP Recovery Manager loads. I finished usi