1131AG not joining to controller (7.4.100)
Hi all,
My customer has an 1131AG AP, andhas Problems with joining to the controller.
I did a debug and have the following output.
The WLC (5508) shows the AP with Primary SW version as 3.0.51.0. this Release does not showup in any compat matrix!
It seems to start downloading the software. after a while it stops with the bolded output, twice the same Bytecount!?
After that it startsover the process again.
who can help me?
Thanks
Willem
*spamApTask0: Apr 03 09:55:59.998: 68:ef:bd:94:e7:9c 5179392 Bytes Transferred to AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:56:00.097: 68:ef:bd:94:e7:9c Received LWAPP IMAGE_DATA_RES from AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:56:00.097: 68:ef:bd:94:e7:9c 5180416 Bytes Transferred to AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:56:00.161: 68:ef:bd:94:e7:9c Received LWAPP IMAGE_DATA_RES from AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:56:00.161: 68:ef:bd:94:e7:9c 5181440 Bytes Transferred to AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:56:00.231: 68:ef:bd:94:e7:9c Received LWAPP IMAGE_DATA_RES from AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:56:00.231: 68:ef:bd:94:e7:9c 5181440 Bytes Transferred to AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:56:00.277: 68:ef:bd:94:e7:9c Received LWAPP IMAGE_DATA_RES from AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:57:24.132: 68:ef:bd:94:e7:9c Did not receive hearbeat reply from AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:59:02.698: 68:ef:bd:94:e7:9c Received LWAPP DISCOVERY REQUEST to 64:00:f1:f5:a5:6f on port '13'
*spamApTask0: Apr 03 09:59:02.698: 68:ef:bd:94:e7:9c Join Priority Processing status = 0, Incoming Ap's Priority 0, MaxLrads = 350,joined Aps =149
*spamApTask0: Apr 03 09:59:02.699: 68:ef:bd:94:e7:9c Successful transmission of LWAPP Discovery Response to AP 68:ef:bd:94:e7:9c on port 13
*spamApTask0: Apr 03 09:59:02.699: 68:ef:bd:94:e7:9c Received LWAPP DISCOVERY REQUEST to 64:00:f1:f5:a5:6f on port '13'
*spamApTask0: Apr 03 09:59:02.699: 68:ef:bd:94:e7:9c Join Priority Processing status = 0, Incoming Ap's Priority 0, MaxLrads = 350,joined Aps =149
*spamApTask0: Apr 03 09:59:02.699: 68:ef:bd:94:e7:9c Successful transmission of LWAPP Discovery Response to AP 68:ef:bd:94:e7:9c on port 13
*spamApTask0: Apr 03 09:59:12.711: 68:ef:bd:94:e7:9c Received LWAPP JOIN REQUEST from AP 68:ef:bd:94:e7:9c to 64:00:f1:f5:a5:6f on port '13'
*spamApTask0: Apr 03 09:59:12.711: Could not find BoardDataPayload
*spamApTask0: Apr 03 09:59:12.736: 68:ef:bd:94:e7:9c AP AP68ef.bd94.e79c: txNonce 00:00:00:00:00:00 rxNonce 00:00:00:00:00:00
*spamApTask0: Apr 03 09:59:12.736: 68:ef:bd:94:e7:9c LWAPP Join Request MTU path from AP 68:ef:bd:94:e7:9c is 1500, remote debug mode is 0
*spamApTask0: Apr 03 09:59:12.984: 68:ef:bd:94:e7:9c Successful transmission of LWAPP Join Reply to AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:59:12.984: 68:ef:bd:94:e7:9c spam_lrad.c:2125 - Operation State 0 ===> 4
*spamApTask0: Apr 03 09:59:14.449: 68:ef:bd:94:e7:9c Received LWAPP IMAGE_DATA from AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:59:14.449: 68:ef:bd:94:e7:9c spam_lrad.c:11846 - Operation State 4 ===> 5
*spamApTask0: Apr 03 09:59:14.449: 68:ef:bd:94:e7:9c Size of the Image file to the AP 68:ef:bd:94:e7:9c is 5181440 Bytes
*spamApTask0: Apr 03 09:59:14.449: 68:ef:bd:94:e7:9c Successful transmission of LWAPP Image Data Response to AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:59:14.523: 68:ef:bd:94:e7:9c Received LWAPP IMAGE_DATA_RES from AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:59:14.523: 68:ef:bd:94:e7:9c 1024 Bytes Transferred to AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:59:14.636: 68:ef:bd:94:e7:9c Received LWAPP IMAGE_DATA_RES from AP 68:ef:bd:94:e7:9c
I Also asked the customer to install the newest IOS manually with the following description:
Solution 1:
Manually upgrade the access point to software 7.3
If you only have a few APs that need to be upgraded and have no access to a WLC running 7.3, you can perform manual upgrade by following the procedures below.
1. Download recovery software image for the AP (Use latest 15.x for newer models, or 12.4(x) for older models)
2. Rename the image to the name the AP will be searching for (eg. ap3g1-k9w7-tar.default). You will also see this on the AP console.
3. Configure TFTP server IP to 10.0.0.x and make sure it is on the same VLAN as the AP (AP, by default, will have IP of 10.0.0.1)
4. Disconnect power from the AP.
5. Hold down Mode button and reconnect the power to the AP. (ie. Factory Reset the AP)
6. Release the Mode button when the LED turns red.
7. Once the AP is up and finds the new image on the TFTP server, it will proceed with an upgrade.
Here you find the IOS. (12.4.10b-JDA)
http://software.cisco.com/download/release.html?mdfid=279537722&flowid=6775&softwareid=280775090&release=12.4.10b-JDA&relind=AVAILABLE&rellifecycle=ED&reltype=latest
After that he gave me this Log-file:
ðøXmodem file system is available.
flashfs[0]: 32 files, 9 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 8670208
flashfs[0]: Bytes available: 7328768
flashfs[0]: flashfs fsck took 36 seconds.
Base ethernet MAC Address: 68:ef:bd:94:e7:9c
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
button pressed for 22 seconds
process_config_recovery: set IP address and config to default 10.0.0.1
process_config_recovery: image recovery
image_recovery: Download default IOS tar image tftp://255.255.255.255/c1130-k9w7-tar.default
examining image...
extracting info (273 bytes)
Image info:
Version Suffix: rcvk9w8-
Image Name: c1130-rcvk9w8-mx
Version Directory: c1130-rcvk9w8-mx
Ios Image Size: 2632192
Total Image Size: 2632192
Image Feature: WIRELESS LAN|LWAPP|RECOVERY
Image Family: C1130
Wireless Switch Management Version: 3.0.51.0
Extracting files...
c1130-rcvk9w8-mx/ (directory) 0 (bytes)
extracting c1130-rcvk9w8-mx/c1130-rcvk9w8-mx (2625156 bytes).........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
extracting c1130-rcvk9w8-mx/info (273 bytes)
extracting info.ver (273 bytes)
Deleting existing version...
Deleting flash:/c1130-rcvk9w8-mx...
done.
New software image installed in flash:/c1130-rcvk9w8-mx
Configuring system to use new image...done.
Requested system reload in progress...download took about 112 seconds
Loading "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx"...##################################################################################################################################################################################################################################################################
File "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:17 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
flashfs[1]: 32 files, 9 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 9234432
flashfs[1]: Bytes available: 6764544
flashfs[1]: flashfs fsck took 6 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1131AG-E-K9 (PowerPCElvis) processor (revision C0) with 24566K/8192K bytes of memory.
Processor board ID FCZ1415Q07K
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 3.0.51.0
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 68:EF:BD:94:E7:9C
Part Number : 73-8962-14
PCA Assembly Number : 800-24818-13
PCA Revision Number : A0
PCB Serial Number : FOC141168AC
Top Assembly Part Number : 800-29144-03
Top Assembly Serial Number : FCZ1415Q07K
Top Revision Number : A0
Product/Model Number : AIR-LAP1131AG-E-K9
% Please define a domain-name first.
Press RETURN to get started!
*Mar 1 00:00:07.860: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 215 messages)
*Mar 1 00:00:09.910: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:09.962: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:17 by prod_rel_team
*Mar 1 00:00:10.001: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:10.225: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Mar 1 00:00:10.910: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
*Mar 1 00:00:18.712: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:38.881: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:00:48.881: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:00:58.881: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:08.881: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:11.058: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
*Mar 1 00:01:18.769: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:01:18.881: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:28.881: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:38.881: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:48.881: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:58.350: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 172.25.68.187, mask 255.255.254.0, hostname AP68ef.bd94.e79c
Translating "CISCO-CAPWAP-CONTROLLER.emea.omya.com"...domain server (172.25.68.62) [OK]
Translating "CISCO-LWAPP-CONTROLLER.emea.omya.com"...domain server (172.25.68.62) [OK]
*Mar 1 00:02:09.228: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:02:21.232: %CAPWAP-3-ERRORLOG: Selected MWAR 'CHOFN020'(index 0).
*Mar 1 00:02:21.233: %CAPWAP-3-ERRORLOG: Go join a lwapp controller
*Mar 1 00:02:21.233: %LWAPP-3-CLIENTERRORLOG: Set Transport AddressCalled
examining image...
*Mar 1 00:02:21.248: %LWAPP-5-CHANGED: CAPWAP changed state to JOIN
*Apr 3 15:21:37.352: %LWAPP-5-CHANGED: CAPWAP changed state to IMAGE
extracting info (292 bytes)
Image info:
Version Suffix: k9w8-.124-25e.JAM
Image Name: c1130-k9w8-mx.124-25e.JAM
Version Directory: c1130-k9w8-mx.124-25e.JAM
Ios Image Size: 5018112
Total Image Size: 5181952
Image Feature: WIRELESS LAN|LWAPP
Image Family: C1130
Wireless Switch Management Version: 7.4.100.0
Extracting files...
c1130-k9w8-mx.124-25e.JAM/ (directory) 0 (bytes)
extracting c1130-k9w8-mx.124-25e.JAM/info (292 bytes)
c1130-k9w8-mx.124-25e.JAM/html/ (directory) 0 (bytes)
c1130-k9w8-mx.124-25e.JAM/html/level/ (directory) 0 (bytes)
c1130-k9w8-mx.124-25e.JAM/html/level/1/ (directory) 0 (bytes)
extracting c1130-k9w8-mx.124-25e.JAM/html/level/1/forms.js (17486 bytes)
extracting c1130-k9w8-mx.124-25e.JAM/html/level/1/appsui.js (557 bytes)
extracting c1130-k9w8-mx.124-25e.JAM/html/level/1/ap_home.shtml.gz (1304 bytes)
c1130-k9w8-mx.124-25e.JAM/html/level/1/images/ (directory) 0 (bytes)
extracting c1130-k9w8-mx.124-25e.JAM/html/level/1/images/info.gif (399 bytes)
extracting c1130-k9w8-mx.124-25e.JAM/html/level/1/images/cisco-logo-2007.gif (1648 bytes)
extracting c1130-k9w8-mx.124-25e.JAM/html/level/1/images/background_web41.jpg (732 bytes)
extracting c1130-k9w8-mx.124-25e.JAM/html/level/1/images/login_homeap.gif (19671 bytes)
extracting c1130-k9w8-mx.124-25e.JAM/html/level/1/config.js (24933 bytes)
extracting c1130-k9w8-mx.124-25e.JAM/html/level/1/sitewide.js (16548 bytes)
extracting c1130-k9w8-mx.124-25e.JAM/html/level/1/officeExtendap.css (41795 bytes)
extracting c1130-k9w8-mx.124-25e.JAM/html/level/1/back.shtml (506 bytes)
c1130-k9w8-mx.124-25e.JAM/html/level/15/ (directory) 0 (bytes)
extracting c1130-k9w8-mx.124-25e.JAM/html/level/15/officeExtendapBanner.htm (7108 bytes)
extracting c1130-k9w8-mx.124-25e.JAM/html/level/15/officeExtendapConfig.shtml.gz (2869 bytes)
extracting c1130-k9w8-mx.124-25e.JAM/html/level/15/officeExtendapSummary.htm (712 bytes)
extracting c1130-k9w8-mx.124-25e.JAM/html/level/15/officeExtendapHelp.htm (5007 bytes)
extracting c1130-k9w8-mx.124-25e.JAM/html/level/15/officeExtendapMain.shtml.gz (3350 bytes)
extracting c1130-k9w8-mx.124-25e.JAM/html/level/15/officeExtendapEvent.shtml.gz (983 bytes)
extracting c1130-k9w8-mx.124-25e.JAM/c1130-k9w8-mx.124-25e.JAM (4747539 bytes)
*Apr 3 15:25:22.228: %LWAPP-3-CLIENTERRORLOG: spamVerifyRecvSeqNum : Duplicate seq 115
*Apr 3 15:28:52.336: %LWAPP-3-CLIENTERRORLOG: spamVerifyRecvSeqNum : Duplicate seq 202
*Apr 3 15:30:01.572: %LWAPP-3-CLIENTERRORLOG: spamVerifyRecvSeqNum : Duplicate seq 49
Similar Messages
-
LAP not joining the controller
Gents
I have 1 AP out of ten not joining the controller. I connected the access point to the network and I checked its boot. the access point reaches LWAPP Discovery" and then give me console input. I hard reset the access point and I hard coded an IP address for the AP the AP joins the controller, but when I reset it to assign it to another controller it did not join again.
why the discovery process is not showing the DHCP option 43 configured and DNS for CISCO-LWAPP-CONTROLLER configured on the DNS. All the access point is operating normally except this one. it has many certificate inside, why a hard reset did not work to solve the problem?
Please advise
Thanks,Does the LAP have a valid IP address?
Can the LAP ping the WLC managment IP address?
Console into the LAP and in enable mode, type the command "lwapp ap controller ". -
AP1242 Not joining 4404 controller
Hi all
Can anyone please help, my 1242 access points will not join my controller, I have done a debug and can see the Access point sending a discovery request, then the controller says discovery request sent, but then nothing happens, any ideas what this could be? I can ping the AP fine.
cheers
CarlThere are a number of things that could cause the join request to not show up. If there are no other controllers that the AP could be sending its join request to check to make sure there isn't a duplicate IP with your AP manager interface. Next if you are running LAG make sure the port-channel load-balancing on the switch that the controller is connected to is set to src-dst-ip.
-
IMP: Cisco AIR-CAP1602 &1532 not joining 2504 Controller issue
Dear Team, We have Cisco wireless implementation in clients premises. We have 8 indoor AP (AIR-CAP1602E-AK9) and 2 Outdoor AP (AIR-CAP1532I-AK9) . Seven indoor APs are able to join the 2504 controller, but 1 indoor AIR-CAP1602E AP is not joining and signal is RED continuously while as outdoor AP AIR-CAP1532I-AK9 signal goes blinking from green, red to amber continuously and is not downloading LWAPP image from the controller even after hard reset.
The output for both APs shown below-
1) AIR-CAP1602E-A-K9:
C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Fri 30-Nov-12 15:48 by aselvara
ap: reset
Are you sure you want to reset the system (y/n)?y
System resetting...
Boot from flash
IOS Bootloader - Starting system.
FLASH CHIP: Spansion S25FL256
Xmodem file system is available.
flashfs[0]: 14 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31936000
flashfs[0]: Bytes used: 418304
flashfs[0]: Bytes available: 31517696
flashfs[0]: flashfs fsck took 9 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: 18:e7:28:d1:9b:05
************* loopback_mode = 0
The system is unable to boot automatically because there
are no bootable files.
C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Fri 30-Nov-12 15:48 by aselvarag
Same event repeating, failed to reset and reboot device
2) AIR_CAP1532I-A-K9 (Outdoor AP):
*Mar 1 00:01:22.211: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:01:22.211: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_47:32:e4'running version 7.5.102.0 is rejected.
*Mar 1 00:01:22.211: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:01:22.211: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:01:22.211: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:01:22.211: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 100.1.1.20
signal goes blinking from Grean, Red to Amber continuously.
Failed to download LWAPP image from the controller even after hard reset.
Default image: 7.6.95.12
Logs and screen shot attached
Please advice.
Thanks
AakashHi please note the details below-
AIR-CAP1602E-A-K9:
C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Fri 30-Nov-12 15:48 by aselvara
ap: reset
Are you sure you want to reset the system (y/n)?y
System resetting...
Boot from flash
IOS Bootloader - Starting system.
FLASH CHIP: Spansion S25FL256
Xmodem file system is available.
flashfs[0]: 14 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31936000
flashfs[0]: Bytes used: 418304
flashfs[0]: Bytes available: 31517696
flashfs[0]: flashfs fsck took 9 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: 18:e7:28:d1:9b:05
************* loopback_mode = 0
The system is unable to boot automatically because there
is no bootable files.
C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Fri 30-Nov-12 15:48 by aselvarag
Can't reboot device!
WLC-SYSLOG
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.5.102.0
Bootloader Version............................... 1.0.18
Field Recovery Image Version..................... 1.0.0
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... Cisco_47:32:e4
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 100.1.1.20
Last Reset....................................... Power on reset
System Up Time................................... 0 days 2 hrs 18 mins 39 secs
System Timezone Location......................... (GMT -6:00) Central Time (US a nd Canada)
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
--More-- or (q)uit
Configured Country............................... US - United States
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +32 C
External Temperature............................. +37 C
Fan Status....................................... 4000 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 3
Number of Active Clients......................... 0
Burned-in MAC Address............................ 24:E9:B3:47:32:E0
Maximum number of APs supported.................. 15 -
APs randomly will not join the controller
Hi all,
In short, APs will join the controller immediately using the recovery image, but once it downloads 7.6.100 and reboots, it either cannot join the controller or will take up to 40 minutes.
The AP is in local mode. The AP 1040 eventually joined the controller, 40 minutes after we deleted all the files off the flash which is unacceptable.
*Apr 9 15:38:15.842: %CAPWAP-5-SENDJOIN: sending Join Request to 10.10.10.10
*Apr 9 15:38:15.851: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Apr 9 15:38:15.851: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Apr 9 15:38:15.851: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Apr 9 15:38:15.851: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.10.10.10
*Apr 9 15:38:16.304: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Apr 9 15:38:16.362: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Apr 9 15:38:16.427: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller CONTROLLER-DC
I also had our technician console into a 2602 and we were seeing exact same errors.
SUMMARY OF THIS CASE:
--AP is 1042 and wlc is on 7.6.100.0
--using dhcp option 43 but the AP has static ip
--checked the private config on the AP and it was not sending the discovery request to the desired WLC
--cleared the private config
--primed the AP to desired WLC
--AP sending join request but receiving the following errors:
Apr 4 14:37:47.000: CAPWAP-3-ERRORLOG Go join a capwap controller
*Apr 4 14:36:47.000: CAPWAP-5-DTLSREQSEND DTLS connection request sent peer_ip: 10.10.10.11 peer_port: 5246
*Apr 4 14:36:47.169: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_handshake.c:90 First fragment for seq 2 is missing
*Apr 4 14:37:17.205: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
--cleared the flash except rcv
--ap started downloading the image from the wlc but once it reboots the same errors appear again
--research made on the error message and apparently we are hitting a bug:
https://tools.cisco.com/bugsearch/bug/CSCul08933/?reffering_site=dumpcrHi Leo,
Next the information, I omitted some serial number and descriptions due to confidentiality matters.
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller Product Version.................................. 7.6.100.0 Bootloader Version............................... 1.0.1 Field Recovery Image Version..................... 6.0.182.0 Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27 Build Type....................................... DATA + WPS
System Name...................................... ABCDEF System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069 Redundancy Mode.................................. Disabled IP Address....................................... XXXXXXX Last Reset....................................... Software reset System Up Time................................... 32 days 14 hrs 1 mins 41 secs System Timezone Location......................... (GMT -5:00) Eastern Time (US and Canada) System Stats Realtime Interval................... 5 System Stats Normal Interval..................... 180
Configured Country............................... CA - Canada Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C Internal Temperature............................. +40 C External Temperature............................. +21 C Fan Status....................................... OK
State of 802.11b Network......................... Enabled State of 802.11a Network......................... Enabled Number of WLANs.................................. 5 Number of Active Clients......................... 2215
Burned-in MAC Address............................ F0:F7:55:2B:4A:80 Power Supply 1................................... Present, OK Power Supply 2................................... Absent Maximum number of APs supported.................. 500
(Cisco Controller) >show time
Time............................................. Mon Apr 14 08:40:08 2014
Timezone delta................................... 0:0 Timezone location................................ (GMT -5:00) Eastern Time (US and Canada)
NTP Servers
NTP Polling Interval......................... 36000
Index NTP Key Index NTP Server NTP Msg Auth Status
1 0 A.B.C.D AUTH DISABLED
AP>sh ver
Cisco IOS Software, C3500 Software (AP3G1-K9W8-M), Version 15.2(4)JB3, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Wed 18-Dec-13 21:36 by prod_rel_team
ROM: Bootstrap program is C3500 boot loader
BOOTLDR: C3500 Boot Loader (AP3G1-BOOT-M), Version 15.2 [chayan-apn-0411 116]
AP uptime is 2 days, 17 hours, 15 minutes System returned to ROM by reload System image file is "flash:/ap3g1-k9w8-mx.152-4.JB3/ap3g1-k9w8-xx.152-4.JB3"
Last reload reason:
cisco AIR-CAP3502I-A-K9 (PowerPC460exr) processor (revision A0) with 98294K/32768K bytes of memory.
Processor board ID XXXXXXXX
PowerPC460exr CPU at 666Mhz, revision number 0x18A8 Last reset from reload LWAPP image version 7.6.100.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 70:81:05:9E:F7:36
Part Number : 73-12175-05
PCA Assembly Number : 800-32268-05
PCA Revision Number : A0
PCB Serial Number : XXXXXXX
Top Assembly Part Number : 800-32891-01
Top Assembly Serial Number : FGL1534S7LP
Top Revision Number : A0
Product/Model Number : AIR-CAP3502I-A-K9
Configuration register is 0xF
AP>sh ip int br
Interface IP-Address OK? Method Status Protocol
BVI1 X.Y.W.Z YES TFTP up up
Dot11Radio0 unassigned NO unset up up
Dot11Radio1 unassigned NO unset up up
GigabitEthernet0 unassigned NO unset up up
GigabitEthernet0.1 unassigned YES unset up up
AP>sh inventory
NAME: "AP3500", DESCR: "Cisco Aironet 3500 Series (IEEE 802.11n) Access Point"
PID: AIR-CAP3502I-A-K9 , VID: V01, SN: XXXXXXX -
AIR-CAP3502I-E-K9 does not join preferred controller
I have an AIR-CAP3502I-E-K9 AP that is configured for two WLAN controllers with preferred order. However the AP does not join the primary controller, but uses the secondary one instead. I have a bunch of these AIR-CAP3502I-E-K9s , majority work fine, but three of them not.
I have tried commands according to
https://supportforums.cisco.com/docs/DOC-24917
In the controller's GUI the order is properly configured. I also tried to use 'Clear All Config" option on the controller and configured the AP from the scratch, but this did not help.
Here is what I have
XXXX#sh capwap client config
configMagicMark 0xF1E2D3C4
chkSumV2 30883
chkSumV1 1073
swVer 7.2.111.3
adminState ADMIN_ENABLED(1)
name XXXX
location YYYY
group name
mwarName ZZZZ1
mwarIPAddress 192.168.1.1
mwarName ZZZZ2
mwarIPAddress 192.168.1.2
mwarName
mwarIPAddress 0.0.0.0
ssh status Enabled
Telnet status Enabled
numOfSlots 2
spamRebootOnAssert 1
spamStatTimer 180
randSeed 0xBAC2
transport SPAM_TRANSPORT_L3(2)
transportCfg SPAM_TRANSPORT_DEFAULT(0)
initialisation SPAM_PRODUCTION_DISCOVERY(1)
ApMode Local
ApSubMode Not Configured
AP Rogue Detection Mode Enabled
OfficeExtend AP [0] Disabled
OfficeExtend AP JoinMode[0] Standard
Discovery Timer 10 secs
Heart Beat Timer 30 secs
Led State Enabled 1
Primed Interval 0
AP ILP Pre-Standard Switch Support Disabled
AP Power Injector Disabled
Infrastructure MFP validation Disabled
Configured Switch 1 Addr 192.168.1.2
Configured Switch 2 Addr 192.168.1.1
non-occupancy channels:
Ethernet (Duplex/Speed) auto/auto
*Mar 1 00:14:23.001: %CAPWAP-3-ERRORLOG: Selected MWAR 'ZZZZ2'(index 1).
*Mar 1 00:14:23.001: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Aug 22 12:21:57.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.2 peer_port: 5246
*Aug 22 12:21:57.581: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.1.2 peer_port: 5246
*Aug 22 12:21:57.581: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
My primary one is 192.168.1.1 and secondary is 192.168.1.2, but the AP joins always the secondary one.
The lines above
Configured Switch 1 Addr 192.168.1.2
Configured Switch 2 Addr 192.168.1.1
seem to be suspicious, I would expect the reverse order, but do not know how the code did it.
The only guess is that in the very beginning the AP joined 192.168.1.2, and this was the controller I configured the AP initially from. The AP seems to maybe somehow remember this.
OS version is
swVer 7.2.111.3
Thanks,
VladYes, this is what I am trying all the time - configure the AP to point to the WLCs I want it to join.
Firstly I did through GUI, did not work.
Secondly I used 'Clear All Config" option on the controller and configured the AP from the scratch through GUI, did not work.
Thirdly I tried through command line on the AP, did not work.
I used these commands
XXXX#capwap ap primary-base ZZZZ1 192.168.1.1
XXXX#capwap ap secondary-base ZZZZ2 192.168.1.2
XXXX#sh capwap client config
configMagicMark 0xF1E2D3C4
chkSumV2 30883
chkSumV1 1072
swVer 7.2.111.3
adminState ADMIN_ENABLED(1)
name XXXX
location YYYY
group name
mwarName ZZZZ1
mwarIPAddress 192.168.1.1
mwarName ZZZZ2
mwarIPAddress 192.168.1.2
mwarName
mwarIPAddress 0.0.0.0
ssh status Enabled
Telnet status Enabled
numOfSlots 2
spamRebootOnAssert 1
spamStatTimer 180
randSeed 0xBAC2
transport SPAM_TRANSPORT_L3(2)
transportCfg SPAM_TRANSPORT_DEFAULT(0)
initialisation SPAM_PRODUCTION_DISCOVERY(1)
ApMode Local
ApSubMode Not Configured
AP Rogue Detection Mode Enabled
OfficeExtend AP [0] Disabled
OfficeExtend AP JoinMode[0] Standard
Discovery Timer 10 secs
Heart Beat Timer 30 secs
Led State Enabled 1
Primed Interval 0
AP ILP Pre-Standard Switch Support Disabled
AP Power Injector Disabled
Infrastructure MFP validation Disabled
Configured Switch 1 Addr 192.168.1.2
Configured Switch 2 Addr 192.168.1.1
non-occupancy channels:
Ethernet (Duplex/Speed) auto/auto
XXXX#sh log
Syslog logging: enabled (1 messages dropped, 8 messages rate-limited,
0 flushes, 0 overruns, xml disabled, filtering disabled)
Console logging: level debugging, 61 messages logged, xml disabled,
filtering disabled
Monitor logging: level debugging, 0 messages logged, xml disabled,
filtering disabled
Buffer logging: level debugging, 67 messages logged, xml disabled,
filtering disabled
Logging Exception size (4096 bytes)
Count and timestamp logging messages: disabled
Trap logging: level emergencies, 0 message lines logged
Logging to 255.255.255.255(global) (udp port 514, audit disabled, link down), 0 message lines logged, xml disabled,
filtering disabled
Log Buffer (1048576 bytes):
*Mar 1 00:00:09.424: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:09.434: *** CRASH_LOG = YES
*Mar 1 00:00:09.434: 64bit PCIE devicesSecurity Core found.
Base Ethernet MAC address: E0:5F:B9:A8:00:7F
*Mar 1 00:00:12.482: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:13.731: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:13.797: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:16.996: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:17.052: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1024 messages)
*Mar 1 00:00:17.068: status of voice_diag_test from WLC is false
*Mar 1 00:00:19.182: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3500 Software (AP3G1-K9W8-M), Version 12.4(25e)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Fri 14-Sep-12 19:13 by prod_rel_team
*Mar 1 00:00:19.182: %SNMP-5-COLDSTART: SNMP agent on host XXXX is undergoing a cold start
*Mar 1 00:13:33.342: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:13:33.342: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:13:33.493: status of voice_diag_test from WLC is false
*Mar 1 00:13:33.632: %SSH-5-ENABLED: SSH 2.0 has been enabledlwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:13:33.956: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:13:34.343: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:13:34.343: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:13:36.029: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:13:41.484: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.1.21, mask 255.255.255.0, hostname XXXX
*Mar 1 00:13:51.981: Logging LWAPP message to 255.255.255.255.
*Mar 1 00:14:01.997: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:14:06.099: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:14:07.190: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:14:08.191: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 00:14:08.288: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:14:09.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:14:11.000: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:14:23.001: %CAPWAP-3-ERRORLOG: Selected MWAR 'ZZZZ2'(index 1).
*Mar 1 00:14:23.001: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Aug 23 06:07:13.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.2 peer_port: 5246
*Aug 23 06:07:13.578: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.1.2 peer_port: 5246
*Aug 23 06:07:13.578: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
*Aug 23 06:07:14.025: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Aug 23 06:07:14.091: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Aug 23 06:07:14.094: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller ZZZZ2
*Aug 23 06:07:14.154: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
What I think might be the key to the problem is this
Configured Switch 1 Addr 192.168.1.2
Configured Switch 2 Addr 192.168.1.1
This is not changing no matter what I do.
Thanks,
Vlad -
LWAPP 1231 does not join the controller
I have LWAPP AIR-AP1231G-A-K9 that was moved from one site to the other one. It has now a different IP address taken from DHCP and its former controller does not exist any more.
I am trying to join it to the same kind of controller which is AIR-WLC4402-12-K9 with 7.0.98.0.
However the AP cannot join the controller, first I got these on the controller
0 Wed Jul 3 14:12:56 2013 AAA Authentication Failure for UserName:0014694b3ab2 User Type: WLAN USER
1 Wed Jul 3 14:12:56 2013 Failed to authorize AP with Base Radio MAC 00:14:69:4b:3a:b2. Authorization entry does not exist in Controller's AP Authorization List.
I added the MAC address of the AP into MAC filtering, and now getting these
AAA Authentication Failure for UserName:0014694b3ab2 User Type: WLAN USER
I am reading several discussions, but they seem to be related to mesh OS mismatch.
My AP is for sure not with mesh OS as it was connected to the controller before the move.
System image file is "flash:/c1200-k9w8-mx.124-23c.JA/c1200-k9w8-mx.124-23c.JA"
#sh capwap client config
swVer 7.0.98.0
Does anyone know what to do to get the AP joined to the controller ?
I had another AP where I tried to reset the LWAPP config - clear lwapp private-config, but this did not help and this AP is now constantly rebooting without allowing me to login. It looks like the only way how to wake it up would be to convert to autonomous and then back to LWAPP which is something I cannot do as I am too far from it.
Thanks,
VladHello George,
Many thanks. I have not converted the AP from autonomous to lwapp, it has been lwapp since the very beginning. We just moved this AP from one site where it was successfully joined the controller as lwapp to other site where I am trying to join the same kind of controller with the same OS, same general settings but different IPs.
I do not understand what could happen to the AP as for sure it was just shipped and not touched IT wise.
Anyway, I will try the excersise described in the link above.
Thanks,
Vlad -
Accesspoint not joining correct controller
Hi,
I am trying to setup a 2504 Wireless Controller with a few AIR-AP1262N-E-K9 Access Points. But i'm having trouble getting the access points to connect to the controller.
The controller and AP's are setup at a local network at one of my customers. They are part of a quite large organization and are therefore connected to some of their other divisions in different contries via MPLS. The DHCP and DNS servers are therefore on a different subnet.
I have confirmed that the Access Points do get a correct IP from the DHCP server and that i am able to ping from the controller to the AP. When looking at the controller it does not receive any join requests from the AP's.
I have setup a console connection to the controller and 1 AP, so i can view debug information.
Most guides mention that you can run different LWAPP commands from the CLI on the AP like show lwapp for example. But i am not able to run any of these LWAPP commands on my AP.
I was hinted that this could be due to the fact that the AP was actually connected to a controller. Is there any way to confirm this from the CLI on the AP? I have run the following command: ap#show controller which gave the following output:
interface Dot11Radio0
Radio Dortmunder 2.4
I was wondering if this could actually mean that the AP had joined another controller?
When looking at the LED it is constant green which should mean that it up and running, but no clients is associated to it yet.
Any ideas would be greatly appreciated.ap#show version
Cisco IOS Software, C1260 Software (AP3G1-K9W7-M), Version 12.4(25d)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 11-Aug-11 02:07 by prod_rel_team
ROM: Bootstrap program is C1260 boot loader
BOOTLDR: C1260 Boot Loader (AP3G1-BOOT-M) Version 12.4(23c)JA5, RELEASE SOFTWARE (fc1)
ap uptime is 1 hour, 34 minutes
System returned to ROM by reload
System image file is "flash:/ap3g1-k9w7-mx.124-25d.JA1/ap3g1-k9w7-mx.124-25d.JA1"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-AP1262N-E-K9 (PowerPC460exr) processor (revision A0) with 81910K/49152K bytes of memory.
Processor board ID FCZ1631Z058
PowerPC460exr CPU at 666Mhz, revision number 0x18A8
Last reset from reload
1 Gigabit Ethernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 30:F7:0D:13:02:C9
Part Number : 73-12175-06
PCA Assembly Number : 800-32268-06
PCA Revision Number : A0
PCB Serial Number : FOC16274Y8E
Top Assembly Part Number : 800-33866-02
Top Assembly Serial Number : FCZ1631Z058
Top Revision Number : A0
Product/Model Number : AIR-AP1262N-E-K9
Configuration register is 0xF -
AP1042N not joining 5508 controller
I am trying to configure new 5508wireless controller, AP 1042N model access points are able to receive DHCP IP address from Controller, but not able to join them.
Please provide the requirements and basic configuration details for this.WLC : sh sysinfo:
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.220.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console
1.27
Build Type....................................... DATA + WPS
System Name...................................... Cisco_bc:56:44
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 192.168.9.100
Last Reset....................................... Software reset
System Up Time................................... 0 days 2 hrs 45 mins 36 secs
System Timezone Location.........................
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
WAP; Sh version:
Cisco IOS Software, C1040 Software (C1140-K9W7-M), Version 12.4(25d)JA1, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 11-Aug-11 02:58 by prod_rel_team
ROM: Bootstrap program is C1040 boot loader
BOOTLDR: C1040 Boot Loader (C1140-BOOT-M) Version 12.4(23c)JA3, RELEASE SOFTWARE
(fc1)
ap uptime is 10 minutes
System returned to ROM by power-on
System image file is "flash:/c1140-k9w7-mx.124-25d.JA1/c1140-k9w7-mx.124-25d.JA1
ap#sh inventory
NAME: "AP1040", DESCR: "Cisco Aironet 1040 Series (IEEE 802.11n) Access Point"
PID: AIR-AP1042N-N-K9 , VID: V04, SN: FGL1620S21W -
Wireless AP not joining Controller
Hi,
I am facing an issue with my AP not joining the controller.
Following is the error log
Mar 1 00:01:11.923: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:01:21.923: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Apr 3 08:10:04.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.146.47.150 peer_port: 5246
*Apr 3 08:10:26.775: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Apr 3 08:10:33.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2051 Max retransmission count reached!
*Apr 3 08:11:03.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.146.47.150:5246
*Apr 3 08:11:03.999: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Apr 3 08:10:04.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.146.47.150 peer_port: 5246Hi Guys,
Thanks for your inputs.
I investigated the issue suspecting a problem with the communication between the WLC and the APs. Actually the WLC is connected to 2 6506 chassis with the 1st chassis as the root.
I discovered a minor error on the module in the 1st chassis. When i connected to the 2nd chassis. The AP was able to join the controller. Outputs for the faulty module as below:
Looks like I will need to RMA the module.
Router#sh module
Mod Ports Card Type Model Serial No.
1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1743F20V
2 16 CEF720 16 port 10GE WS-X6716-10GE SAL1746G9RS
3 16 CEF720 16 port 10GE WS-X6716-10GE SAL1746G9QR
5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G SAL1746GC1G
Mod MAC addresses Hw Fw Sw Status
1 7c69.f690.8908 to 7c69.f690.8937 4.3 12.2(18r)S1 12.2(33)SXJ6 Ok
2 7c69.f690.badc to 7c69.f690.baeb 2.1 12.2(18r)S1 12.2(33)SXJ6 Ok
3 e4d3.f1a4.39f8 to e4d3.f1a4.3a07 2.1 12.2(18r)S1 12.2(33)SXJ6 Ok
5 5057.a8e3.394a to 5057.a8e3.3951 4.1 8.5(4) 12.2(33)SXJ6 Ok
Mod Sub-Module Model Serial Hw Status
1 Centralized Forwarding Card WS-F6700-CFC SAL1746GAAX 4.1 Ok
2 Distributed Forwarding Card WS-F6700-DFC3C SAL1746G6T1 1.6 Ok
3 Distributed Forwarding Card WS-F6700-DFC3C SAL1746G844 1.6 Ok
5 Policy Feature Card 3 VS-F6K-PFC3C SAL1746GBJK 1.2 Ok
5 MSFC3 Daughterboard VS-F6K-MSFC3 SAL1746GAGT 5.1 Ok
Mod Online Diag Status
1 Minor Error
2 Pass
3 Pass
5 Pass
Router#sh diagnostic result module 1
Current bootup diagnostic level: minimal
Module 1: CEF720 48 port 10/100/1000mb Ethernet SerialNo : SAL1743F20V
Overall Diagnostic Result for Module 1 : MINOR ERROR
Diagnostic level at card bootup: minimal
Test results: (. = Pass, F = Fail, U = Untested)
1) TestLoopback:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
2) TestTxPathMonitoring ------------> .
3) TestSynchedFabChannel -----------> .
4) TestL3VlanMet -------------------> F
5) TestIngressSpan -----------------> .
6) TestEgressSpan ------------------> .
7) TestAsicMemory ------------------> U
8) TestEobcStressPing --------------> U
9) TestFirmwareDiagStatus ----------> .
10) TestAsicSync --------------------> .
11) TestUnusedPortLoopback:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
U U U U U U U U U U U . U U U U U U U U U U U .
Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
U U U U U U U U U U U . U U U U U U U U U U U .
12) TestOBFL ------------------------> .
13) TestErrorCounterMonitor ---------> .
14) TestPortTxMonitoring:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
U U U U U U U U U U U U U U U U U U U U U U U U
Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
U U U U U U U U U U U U U U U U U U U U U U U U
15) TestLtlFpoeMemoryConsistency ----> .
16) TestRwEngineOverSubscription ----> U
Router#sh diagnostic result module 1 detail
Current bootup diagnostic level: minimal
Module 1: CEF720 48 port 10/100/1000mb Ethernet SerialNo : SAL1743F20V
Overall Diagnostic Result for Module 1 : MINOR ERROR
Diagnostic level at card bootup: minimal
Test results: (. = Pass, F = Fail, U = Untested)
1) TestLoopback:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Apr 01 2014 10:55:39
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:55:39
Total failure count ---------> 0
Consecutive failure count ---> 0
2) TestTxPathMonitoring ------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 40
Last test testing type ------> Health Monitoring
Last test execution time ----> Apr 01 2014 10:57:30
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:57:30
Total failure count ---------> 0
Consecutive failure count ---> 0
3) TestSynchedFabChannel -----------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 39
Last test testing type ------> Health Monitoring
Last test execution time ----> Apr 01 2014 10:57:30
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:57:30
Total failure count ---------> 0
Consecutive failure count ---> 0
4) TestL3VlanMet -------------------> F
Error code ------------------> 54 (DIAG_CHECK_UDP_PAK_ERROR)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Apr 01 2014 10:55:53
First test failure time -----> Apr 01 2014 10:55:53
Last test failure time ------> Apr 01 2014 10:55:53
Last test pass time ---------> n/a
Total failure count ---------> 1
Consecutive failure count ---> 1
5) TestIngressSpan -----------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Apr 01 2014 10:56:05
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:56:05
Total failure count ---------> 0
Consecutive failure count ---> 0
6) TestEgressSpan ------------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Apr 01 2014 10:56:05
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:56:05
Total failure count ---------> 0
Consecutive failure count ---> 0
7) TestAsicMemory ------------------> U
Error code ------------------> 3 (DIAG_SKIPPED)
Total run count -------------> 0
Last test testing type ------> n/a
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
8) TestEobcStressPing --------------> U
Error code ------------------> 3 (DIAG_SKIPPED)
Total run count -------------> 0
Last test testing type ------> n/a
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
9) TestFirmwareDiagStatus ----------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Apr 01 2014 10:56:05
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:56:05
Total failure count ---------> 0
Consecutive failure count ---> 0
10) TestAsicSync --------------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 5
Last test testing type ------> Health Monitoring
Last test execution time ----> Apr 01 2014 10:57:21
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:57:21
Total failure count ---------> 0
Consecutive failure count ---> 0
11) TestUnusedPortLoopback:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
U U U U U U U U U U U . U U U U U U U U U U U .
Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
U U U U U U U U U U U . U U U U U U U U U U U .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Health Monitoring
Last test execution time ----> Apr 01 2014 10:57:06
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:57:06
Total failure count ---------> 0
Consecutive failure count ---> 0
12) TestOBFL ------------------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Apr 01 2014 10:56:05
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:56:05
Total failure count ---------> 0
Consecutive failure count ---> 0
13) TestErrorCounterMonitor ---------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 2
Last test testing type ------> Health Monitoring
Last test execution time ----> Apr 01 2014 10:57:06
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:57:06
Total failure count ---------> 0
Consecutive failure count ---> 0
Error Records ---------------> n/a
14) TestPortTxMonitoring:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
U U U U U U U U U U U U U U U U U U U U U U U U
Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
U U U U U U U U U U U U U U U U U U U U U U U U
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Health Monitoring
Last test execution time ----> Apr 01 2014 10:57:21
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:57:21
Total failure count ---------> 0
Consecutive failure count ---> 0
15) TestLtlFpoeMemoryConsistency ----> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 5
Last test testing type ------> Health Monitoring
Last test execution time ----> Apr 01 2014 10:57:21
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:57:21
Total failure count ---------> 0
Consecutive failure count ---> 0
16) TestRwEngineOverSubscription ----> U
Error code ------------------> 3 (DIAG_SKIPPED)
Total run count -------------> 0
Last test testing type ------> n/a
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
Router#sh diagnostic result module 1 failure
Current bootup diagnostic level: minimal
Module 1: CEF720 48 port 10/100/1000mb Ethernet SerialNo : SAL1743F20V
Overall Diagnostic Result for Module 1 : MINOR ERROR
Diagnostic level at card bootup: minimal
Test results: (. = Pass, F = Fail, U = Untested)
4) TestL3VlanMet -------------------> F -
AIR-CAP3501I access point not joining the Cisco 2100 Wireless Lan controller.
Hello All,
I am installing a new LAP (AIR-CAP3501I ) through the wireless lan controller (AIR-WLC2112-K9) with software version 7.0. I have an external ADSL modem which will act as the DHCP server for the wireless clients and the LAP.
Please find my network setup as below:
The ISP ADSL modem , WLC and LAP are connected to a unmanaged POE switch. The LAP gets its power through the POE switch. When i connect the LAP and the WLC to the switch along with the ADSL modem, the LAPs are getting the ip address from the ADSL modem, however they are not joining the WLC for further process.
ADSL Modem ip address: 192.168.1.254
Management ip address on the LAP: 192.168.1.1 ( Assigned to port 1, untagged Vlan).
Ap Manager ip address: 192.168.1.1 ( Assigned to the same port i.e port1, Untagged Vlan).
The LAP is getting an IP address from the ADSL modem in the range of the DHCP scope.
I will paste the logs very soon.
Please let me know if i am doing anything wrong oe what will be the issue.
Thanks in advance,
Mohammed AmeenHello All,
Please find the logs for "debug capwap event" from the WLC below:
*spamReceiveTask: Sep 26 19:44:59.196: e8:04:62:0a:3f:10 Join Version: = 117465600
*spamReceiveTask: Sep 26 19:44:59.197: e8:04:62:0a:3f:10 Join resp: CAPWAP Maximum Msg element len = 92
*spamReceiveTask: Sep 26 19:44:59.197: e8:04:62:0a:3f:10 Join Response sent to 192.168.1.156:45510
*spamReceiveTask: Sep 26 19:44:59.197: e8:04:62:0a:3f:10 CAPWAP State: Join
*spamReceiveTask: Sep 26 19:44:59.197: e8:04:62:0a:3f:10 capwap_ac_platform.c:1216 - Operation State 0 ===> 4
*apfReceiveTask: Sep 26 19:44:59.198: e8:04:62:0a:3f:10 Register LWAPP event for AP e8:04:62:0a:3f:10 slot 0
*spamReceiveTask: Sep 26 19:44:59.341: e8:04:62:0a:d1:20 DTLS connection not found, creating new connection for 192:168:1:158 (45644) 192:168:1:2 (5246)
*spamReceiveTask: Sep 26 19:45:00.119: e8:04:62:0a:d1:20 DTLS Session established server (192.168.1.2:5246), client (192.168.1.158:45644)
*spamReceiveTask: Sep 26 19:45:00.119: e8:04:62:0a:d1:20 Starting wait join timer for AP: 192.168.1.158:45644
*spamReceiveTask: Sep 26 19:45:00.121: e8:04:62:0a:d1:20 Join Request from 192.168.1.158:45644
*spamReceiveTask: Sep 26 19:45:00.123: e8:04:62:0a:d1:20 Join Version: = 117465600
*spamReceiveTask: Sep 26 19:45:00.123: e8:04:62:0a:d1:20 Join resp: CAPWAP Maximum Msg element len = 92
*spamReceiveTask: Sep 26 19:45:00.124: e8:04:62:0a:d1:20 Join Response sent to 192.168.1.158:45644
*spamReceiveTask: Sep 26 19:45:00.124: e8:04:62:0a:d1:20 CAPWAP State: Join
*spamReceiveTask: Sep 26 19:45:00.124: e8:04:62:0a:d1:20 capwap_ac_platform.c:1216 - Operation State 0 ===> 4
*apfReceiveTask: Sep 26 19:45:00.125: e8:04:62:0a:d1:20 Register LWAPP event for AP e8:04:62:0a:d1:20 slot 0
*spamReceiveTask: Sep 26 19:45:00.273: e8:04:62:0a:d1:20 Configuration Status from 192.168.1.158:45644
*spamReceiveTask: Sep 26 19:45:00.273: e8:04:62:0a:d1:20 CAPWAP State: Configure
*spamReceiveTask: Sep 26 19:45:00.273: Invalid channel 1 spacified for the AP APf866.f2ab.24b6, slotId = 0
*spamReceiveTask: Sep 26 19:45:00.274: e8:04:62:0a:d1:20 Updating IP info for AP e8:04:62:0a:d1:20 -- static 0, 192.168.1.158/255.255.255.0, gtw 192.168.1.254
*spamReceiveTask: Sep 26 19:45:00.274: e8:04:62:0a:d1:20 Updating IP 192.168.1.158 ===> 192.168.1.158 for AP e8:04:62:0a:d1:20
*spamReceiveTask: Sep 26 19:45:00.274: e8:04:62:0a:d1:20 Setting MTU to 1485
*spamReceiveTask: Sep 26 19:45:00.274: e8:04:62:0a:d1:20 Finding DTLS connection to delete for AP (192:168:1:158/45644)
*spamReceiveTask: Sep 26 19:45:00.274: e8:04:62:0a:d1:20 Disconnecting DTLS Capwap-Ctrl session 0xa06d6a4 for AP (192:168:1:158/45644)
*spamReceiveTask: Sep 26 19:45:00.274: e8:04:62:0a:d1:20 CAPWAP State: Dtls tear down
*spamReceiveTask: Sep 26 19:45:00.277: spamProcessGlobalPathMtuUpdate: Changing Global LRAD MTU to 576
*spamReceiveTask: Sep 26 19:45:00.277: e8:04:62:0a:d1:20 DTLS connection closed event receivedserver (192:168:1:2/5246) client 192:168:1:158/45644).
The Acess point joins the Controller for 2-3 seconds and then unjoins again. I am not sure what i am doing wrong here. The access points are getting the IPs from the ADSL modem through the switch, then it talks to the WLC, however it does not join the controller for further process.
Note:
The Managemnet interface and the AP manager interface are assigned to the same port 1 with unassigned Vlan as mention above. -
hi All,
I have a scenario where my 2602E is not joining a controller in US. AP is in Netherlands.
AP: AIR-CAP2602E-E-K9
Logs on WLC 5508:
*spamApTask4: Jan 29 10:26:37.398: 18:9c:5d:9b:4d:00 Bridge AP can not join MultiCountry Controller: Bridge mode AP 10.130.90.11:63313 cannot be supported on Multi Country Controll
*spamApTask4: Jan 29 10:26:37.406: 18:9c:5d:9b:4d:00 State machine handler: Failed to process msg type = 3 state = 0 from 10.130.90.11:63313
is there a way i can change the bridge mode from this AP to normal or Local so that it can be useD?
Any help will be great.
thanks
Roycecheck the following.
-
LWAP not joining controller, but has downloaded software
Hi All,
I have four APs that when I powered on individually, they went into the downloading state and rebooted, now have the mac address APxxxx.xxxx.xxxx.cisco.com and can see this on my switch and cdp is working, but has not joined the controller?
I know that DHCP is set correctly as I have another AP on the switch/VLAN that is working?
Any ideas?
Many thx indeed,
KenTo answer your specific question, there's no need to clear anything on the WLC. The access points should simply connect.
Did you upgrade these access points, and could this be a certificate issue? If they are upgraded 1100s or 1200s, you may need to add the SSCs generated during the upgrade process into the controller. This can be done under the Security tab.
If that's not the issue, I would try to connect the access points more directly by placing them on the management subnet. This will hopefully tell you whether there's a problem with your discovery method.
Have you looked at the access points to see their status according to their LEDs? Are they still seeking a controller? Is it possible that they've found a different controller somewhere else on the network? -
Mesh AP 1524SB Not Joining Controller
Hello,
I'm just getting started here and have run into some problems.
I have a WLC 5508 running 7.0.116.0 and 1524SB access points.
I have a 3750 switch sitting between them hosting the DHCP.
The switch is using VLAN 1 and the management interface of the WLC is untagged.
The problem is that my APs will not join the controller. I don't even think they are getting an IP address.
When I console into the AP it seems to me that the boot process is interupted and the AP reboots.
I get this message:
*Mar 1 00:00:34.375: %SYS-5-RELOAD: Reload requested by Adj Process. Reload Reason: Mesh Reboots AP ....
*Mar 1 00:00:34.375: %LWAPP-5-CHANGED: CAPWAP changed state to DOWNWriting out the event log to nvram...
And then it reboots. I have attached the entire boot sequence.
Could someone help me out please?
Thanks,
Justin
PS if needed here is the dhcp config:
ip dhcp pool dhcp
network 10.0.0.0 255.255.255.0
default-router 10.0.0.254
option 60 ascii "Cisco AP c1520"
option 43 ip 10.0.0.1
where 10.0.0.1 is the ip of the management interface.Assuming 10.0.0.1 is the controller's management IP address. For 1524SB Mesh AP, you can't use format of "option 43 ip 10.0.0.1", change it to "option 43 hex f1040a000001" on the 3750 switch and try again.
-
3702i AP's not Joining WLC - Layer 3 discovery request not received on management VLAN
Hi Guys,
This is a follow up post to this thread: https://supportforums.cisco.com/discussion/12400481/3702i-not-joint-2504
Have been playing around with my AP's and made sure the time is correct on all the devices ( WLC and Switch). I have also moved the AP's to the same Vlan as the management IP of the WLC.
if I move the AP's to the same Vlan as the WLC they join and are happy, as soon as I move them to a different Vlan they cant join and there time goes back to the default plus they do not seem to save the WLC details to flash but still remember the test names I give them.
it appears that option 43 is working fine as I can see it look for the WLC IP and I have done some trouble shooting on the WLC and it looks like it see's the AP but doesn't except it.
please see below for the boot up of the AP and the WLC logs:
AP
IIOS Bootloader - Starting system.
*** deleted for breverity *****
Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1"...#########################
File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1" uncompressed and installed, entry point: 0x2003000
executing...
Secondary Bootloader - Starting system.
Montserrat Board
*** deleted for breverity *****
Boot CMD: 'boot flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1;flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1'
Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1"...###############################################
File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1" uncompressed and installed, entry point: 0x1003000
executing...
*** deleted for breverity *****
cisco AIR-CAP3702I-Z-K9 (PowerPC) processor (revision A0) with 376810K/134656K bytes of memory.
Processor board ID FGL1838X4T1
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 8.0.110.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: F4:4E:05:B7:1E:84
Part Number : 73-15243-01
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC18343WPR
Top Assembly Part Number : 068-05054-03
Top Assembly Serial Number : FGL1838X4T1
Top Revision Number : A0
Product/Model Number : AIR-CAP3702I-Z-K9
% Please define a domain-name first.
Press RETURN to get started!
*Mar 1 00:00:19.295: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
*Mar 1 00:00:19.755: Registering HW DTLS
*Mar 1 00:00:19.763: APAVC: Initial WLAN Buffers Given to System is 2500
*Mar 1 00:00:19.815: APAVC: WlanPAKs 42878 RadioPaks 42270
*Mar 1 00:00:22.127: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:26.055: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
*Mar 1 00:00:26.167: Loading Power Tables from ram:/Q2.bin. Class = A
*Mar 1 00:00:26.167: record size of 3ss: 1168 read_ptr: 4F9698E
*Mar 1 00:00:31.207: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
*Mar 1 00:00:31.251: Loading Power Tables from ram:/Q5.bin. Class = Z
*Mar 1 00:00:31.251: record size of vht: 2904 read_ptr: 4F9698E
*Mar 1 00:00:31.407: Wait until the stile protocol list is initialized.
*Mar 1 00:00:32.651: Start STILE Activation
*Mar 1 00:00:34.571: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 00:00:35.447: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 19-Dec-14 11:20 by prod_rel_team
*Mar 1 00:00:35.447: %SNMP-5-COLDSTART: SNMP agent on host Test_1 is undergoing a cold start
*Mar 1 00:00:36.563: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:37.787: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:37.939: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:37.939: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:47.567: %LINK-6-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:48.567: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
*Mar 1 00:00:50.431: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (2-16)
*Mar 1 00:00:50.431: DPAA Initialization Complete
*Mar 1 00:00:50.431: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Mar 1 00:00:51.431: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:53.435: %LINK-6-UPDOWN: Interface BVI1, changed state to up
*Mar 1 00:00:53.867: Currently running a Release Image
*Mar 1 00:00:54.287: Incorrect certificate in SHA2 PB !
*Mar 1 00:00:54.287: Using SHA-1 signed certificate for image signing validation.
*Mar 1 00:00:54.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:59.787: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.2, mask 255.255.255.0, hostname Test_1
*Mar 1 00:01:02.707: APAVC: Succeeded to activate all the STILE protocols.
*Mar 1 00:01:02.707: APAVC: Registering with CFT
*Mar 1 00:01:02.707: APAVC: CFT registration of delete callback succeeded
*Mar 1 00:01:02.707: APAVC: Reattaching Original Buffer pool for system use
*Mar 1 00:01:02.707: Pool-ReAtach: paks 42878 radio42270
%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 00:01:10.103: AP image integrity check PASSED
*Mar 1 00:01:10.187: Incorrect certificate in SHA2 PB !
*Mar 1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:01:11.591: %CDP_PD-4-POWER_OK: 15.4 W power - NEGOTIATED inline power source
*Mar 1 00:01:12.691: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:01:13.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:01:13.947: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:01:14.947: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 00:01:20.211: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:01:31.215: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
*Mar 1 00:02:11.599: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:02:11.603: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 1 00:02:11.611: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:02:12.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:02:12.639: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:02:12.647: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Mar 1 00:02:12.655: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:02:13.639: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:02:13.647: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:02:13.699: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:02:14.699: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
Not in Bound state.
*Mar 1 00:02:44.719: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
*Mar 1 00:02:49.839: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.3, mask 255.255.255.0, hostname Test_1
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:02:55.719: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
Not in Bound state.
*Mar 1 00:03:59.219: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
*Mar 1 00:04:04.343: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.4, mask 255.255.255.0, hostname Test_1
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:04:10.223: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
WLC:
isco Controller) >show time
Time............................................. Tue Jan 27 17:44:47 2015
Timezone delta................................... 0:0
Timezone location................................ (GMT +8:00) HongKong, Bejing, Chongquing
NTP Servers
NTP Polling Interval......................... 3600
Index NTP Key Index NTP Server NTP Msg Auth Status
1 0 150.101.176.226 AUTH DISABLED
(Cisco Controller) >show ap join stats summary
Incorrect input! Use 'show ap join stats summary [all/<ap-mac>]'
(Cisco Controller) >show ap join stats summary all
Number of APs.............................................. 2
Base Mac AP EthernetMac AP Name IP Address Status
f4:4e:05:aa:a6:a0 f4:4e:05:94:c3:98 APf44e.0594.c398 10.1.1.22 Joined
f4:4e:05:b6:ce:f0 N A Test_1 10.1.20.7 Not Joined
(Cisco Controller) >show ap join stats detailed f4:4e:05:b6:ce:f0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
Discovery phase statistics
- Discovery requests received.............................. 45
- Successful discovery responses sent...................... 21
- Unsuccessful discovery request processing................ 24
- Reason for last unsuccessful discovery attempt........... Layer 3 discovery request not received on management VLAN
- Time at last successful discovery attempt................ Jan 27 17:45:49.705
- Time at last unsuccessful discovery attempt.............. Jan 27 17:45:49.705
Join phase statistics
- Join requests received................................... 0
- Successful join responses sent........................... 0
- Unsuccessful join request processing..................... 0
- Reason for last unsuccessful join attempt................ Not applicable
- Time at last successful join attempt..................... Not applicable
- Time at last unsuccessful join attempt................... Not applicable
Configuration phase statistics
--More-- or (q)uit
- Configuration requests received.......................... 0
- Successful configuration responses sent.................. 0
- Unsuccessful configuration request processing............ 0
- Reason for last unsuccessful configuration attempt....... Not applicable
- Time at last successful configuration attempt............ Not applicable
- Time at last unsuccessful configuration attempt.......... Not applicable
Last AP message decryption failure details
- Reason for last message decryption failure............... Not applicable
Last AP disconnect details
- Reason for last AP connection failure.................... Not applicable
- Last AP disconnect reason................................ Not applicable
Last join error summary
- Type of error that occurred last......................... Lwapp discovery request rejected
- Reason for error that occurred last...................... Layer 3 discovery request not received on management VLAN
- Time at which the last join error occurred............... Jan 27 17:45:49.705
AP disconnect details
- Reason for last AP connection failure.................... Not applicable
Ethernet Mac : 00:00:00:00:00:00 Ip Address : 10.1.20.7
(Cisco Controller) >show interface summary
Number of Interfaces.......................... 4
Interface Name Port Vlan Id IP Address Type Ap Mgr Guest
ap LAG 20 10.1.20.231 Dynamic No No
guest LAG 30 10.1.30.231 Dynamic No No
management LAG 10 10.1.1.231 Static Yes No
virtual N/A N/A 1.1.1.1 Static No No
SWITCH
witch#show run
Building configuration...
*** deleted for breverity *****
no aaa new-model
clock timezone AWST 8
system mtu routing 1500
ip routing
ip dhcp pool WAP_Pool
network 10.1.20.0 255.255.255.0
default-router 10.1.20.1
option 43 hex f104.0a01.01e7
ip dhcp pool Clients
network 10.1.30.0 255.255.255.0
default-router 10.1.30.1
dns-server 203.0.178.191
ip dhcp pool test
network 10.1.1.0 255.255.255.0
default-router 10.1.1.1
crypto pki trustpoint TP-self-signed-4082587776
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-4082587776
revocation-check none
rsakeypair TP-self-signed-4082587776
*** deleted for breverity *****
*** deleted for breverity ***** !
interface FastEthernet0/3
description *** WLC ****
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet0/4
description **** AP *****
switchport access vlan 20
switchport mode access
spanning-tree portfast
interface FastEthernet0/5
description **** AP ****
switchport access vlan 20
switchport mode access
spanning-tree portfast
interface FastEthernet0/6
i*** deleted for breverity ***** !
interface Vlan10
description *** Managment ***
ip address 10.1.1.230 255.255.255.0
interface Vlan20
description *** WIRELESS APS ***
ip address 10.1.20.1 255.255.255.0
interface Vlan30
ip address 10.1.30.1 255.255.255.0
ip classless
ip route 0.0.0.0 0.0.0.0 10.1.1.1
ip http server
ip http secure-server
ip sla enable reaction-alerts
l*** deleted for breverity *****
ntp clock-period 36028827
ntp source FastEthernet0/1
ntp server 121.0.0.42
ntp server 202.127.210.37
end
I have also placed a Device in Vlan 20 and it is able to ping the WLC and the WLC can ping it s routing is working.
ThanksHey Scott,
I gave that a shot and still no luck, log's from AP boot up:
IIOS Bootloader - Starting system.
flash is writable
Tide XL MB - 40MB of flash
Xmodem file system is available.
flashfs[0]: 67 files, 9 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 41158656
flashfs[0]: Bytes used: 20894208
flashfs[0]: Bytes available: 20264448
flashfs[0]: flashfs fsck took 20 seconds.
Base Ethernet MAC address: f4:4e:05:b7:1e:84
Ethernet speed is 100 Mb - FULL Duplex
Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1"...#########################
File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1" uncompressed and installed, entry point: 0x2003000
executing...
Secondary Bootloader - Starting system.
Montserrat Board
40MB format
Tide XL MB - 40MB of flash
Xmodem file system is available.
flashfs[0]: 67 files, 9 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 41158656
flashfs[0]: Bytes used: 20894208
flashfs[0]: Bytes available: 20264448
flashfs[0]: flashfs fsck took 21 seconds.
flashfs[1]: 0 files, 1 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 12257280
flashfs[1]: Bytes used: 1024
flashfs[1]: Bytes available: 12256256
flashfs[1]: flashfs fsck took 1 seconds.
Base Ethernet MAC address: f4:4e:05:b7:1e:84
Boot CMD: 'boot flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1;flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1'
Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1"...###############################################
File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1" uncompressed and installed, entry point: 0x1003000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 19-Dec-14 11:20 by prod_rel_team
Montserrat Board
40MB format
Tide XL MB - 40MB of flash
Initializing flashfs...
flashfs[2]: 67 files, 9 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 40900608
flashfs[2]: Bytes used: 20894208
flashfs[2]: Bytes available: 20006400
flashfs[2]: flashfs fsck took 14 seconds.
flashfs[2]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 11999232
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 11998208
flashfs[4]: flashfs fsck took 0 seconds.
flashfs[4]: Initialization complete.
Copying radio files from flash: to ram:
Copy in progress...CCCCC
Copy in progress...CCC
Copy in progress...CCCC
Copy in progress...CCCC
Copy in progress...CC
Copy in progress...CCCC
Copy in progress...CC
Copy in progress...CCCCC
Copy in progress...CCCC
Copy in progress...CC
Uncompressing radio files...
...done Initializing flashfs.
Radio0 present 8764 8000 0 A8000000 A8010000 0
Rate table has 650 entries (20 legacy/224 11n/406 11ac)
POWER TABLE FILENAME = ram:/Q2.bin
Radio1 present 8864 8000 0 80000000 80100000 4
POWER TABLE FILENAME = ram:/Q5.bin
Radio2 not present 0 0 0 0 0 8
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP3702I-Z-K9 (PowerPC) processor (revision A0) with 376810K/134656K bytes of memory.
Processor board ID FGL1838X4T1
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 8.0.110.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: F4:4E:05:B7:1E:84
Part Number : 73-15243-01
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC18343WPR
Top Assembly Part Number : 068-05054-03
Top Assembly Serial Number : FGL1838X4T1
Top Revision Number : A0
Product/Model Number : AIR-CAP3702I-Z-K9
% Please define a domain-name first.
Press RETURN to get started!
*Mar 1 00:00:19.295: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
*Mar 1 00:00:19.755: Registering HW DTLS
*Mar 1 00:00:19.763: APAVC: Initial WLAN Buffers Given to System is 2500
*Mar 1 00:00:19.815: APAVC: WlanPAKs 42878 RadioPaks 42270
*Mar 1 00:00:22.127: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:26.055: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
*Mar 1 00:00:26.167: Loading Power Tables from ram:/Q2.bin. Class = A
*Mar 1 00:00:26.167: record size of 3ss: 1168 read_ptr: 4F9698E
*Mar 1 00:00:31.207: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
*Mar 1 00:00:31.251: Loading Power Tables from ram:/Q5.bin. Class = Z
*Mar 1 00:00:31.251: record size of vht: 2904 read_ptr: 4F9698E
*Mar 1 00:00:31.407: Wait until the stile protocol list is initialized.
*Mar 1 00:00:32.651: Start STILE Activation
*Mar 1 00:00:34.571: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 00:00:35.447: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 19-Dec-14 11:20 by prod_rel_team
*Mar 1 00:00:35.447: %SNMP-5-COLDSTART: SNMP agent on host Test_1 is undergoing a cold start
*Mar 1 00:00:36.563: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:37.787: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:37.939: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:37.939: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:47.567: %LINK-6-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:48.567: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
*Mar 1 00:00:50.431: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (2-16)
*Mar 1 00:00:50.431: DPAA Initialization Complete
*Mar 1 00:00:50.431: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Mar 1 00:00:51.431: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:53.435: %LINK-6-UPDOWN: Interface BVI1, changed state to up
*Mar 1 00:00:53.867: Currently running a Release Image
*Mar 1 00:00:54.287: Incorrect certificate in SHA2 PB !
*Mar 1 00:00:54.287: Using SHA-1 signed certificate for image signing validation.
*Mar 1 00:00:54.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:59.787: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.2, mask 255.255.255.0, hostname Test_1
*Mar 1 00:01:02.707: APAVC: Succeeded to activate all the STILE protocols.
*Mar 1 00:01:02.707: APAVC: Registering with CFT
*Mar 1 00:01:02.707: APAVC: CFT registration of delete callback succeeded
*Mar 1 00:01:02.707: APAVC: Reattaching Original Buffer pool for system use
*Mar 1 00:01:02.707: Pool-ReAtach: paks 42878 radio42270
%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 00:01:10.103: AP image integrity check PASSED
*Mar 1 00:01:10.187: Incorrect certificate in SHA2 PB !
*Mar 1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:01:11.591: %CDP_PD-4-POWER_OK: 15.4 W power - NEGOTIATED inline power source
*Mar 1 00:01:12.691: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:01:13.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:01:13.947: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:01:14.947: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 00:01:20.211: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:01:31.215: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
*Mar 1 00:02:11.599: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:02:11.603: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 1 00:02:11.611: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:02:12.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:02:12.639: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:02:12.647: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Mar 1 00:02:12.655: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:02:13.639: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:02:13.647: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:02:13.699: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:02:14.699: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
Not in Bound state.
*Mar 1 00:02:44.719: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
*Mar 1 00:02:49.839: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.3, mask 255.255.255.0, hostname Test_1
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:02:55.719: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
Not in Bound state.
*Mar 1 00:03:59.219: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
*Mar 1 00:04:04.343: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.4, mask 255.255.255.0, hostname Test_1
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:04:10.223: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
Maybe you are looking for
-
What issues we may face in installing a new Prod portal with same SID as existing one
Hello All - We found some vbs script files in the host of EP Prod system. On confirmation from SAP we deleted those files without any harm to our prod EP system. But customer is still concerned about the security of the system and wanted us build the
-
There was an error opening this document. This file cannot be found
An automation script on one of our QA environments kept tripping on the error: "There was an error opening this document. This file cannot be found". The same script ran fine against our Production servers (hint, which were "whitelisted"). It took a
-
Hello, I have a situation where I am passing an operator as a parameter to a function. My question is how can I make use of the operator in my code. Function f1(start_date,par_operator) Operator can be 'GT' or 'LT' -- meaning Greater than '>' or Less
-
Audio Configuration Contains Unknown items
Has this issue been resolved ?? I have been using Logic Pro 9 for 3 years and yesterday I encounter this issue. Been searching all over the internet and seems like there are lots of questions out there but I did not see any resolution ?? Thought I wi
-
I have just switched from a PC to my new iMac and love it! However, I can't seem to play small video clips, gif animations, wmv, etc. I tried downloading Windows Media Player from www.mactopia.com and when I open the application I receive a message "