1142 LAP-to-Autonomous Conversion
Guys -
Ordered an AIR-AP1142N-A-K9, but they shipped the LWAPP version. I know with a 1252 I can convert to IOS using the archive command, which is available by issuing "debug lwapp console cli" to enable full IOS command set. This does not work on the new 1142. Anyone know what the new command is?
Regards,
Scott
Have you tried this way.... but you would need an IOS code. If you are consoled and you hold the reset for 20 seconds and let go, does it look for an image? I'm wondering if you can or not convert.... though I heard someone say that you can't.... might be wrong though.
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file for a 1142 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 On the PC where the TFTP server is located, perform these steps:
a. Disable any software firewall products, such as Windows firewall, ZoneAlarm firewall, McAffee firewall, or others.
b. Ensure all Windows files are visible. From Windows Explorer, click Tools > Folder Options > View > Show hidden files and folders.
Step 4 Rename the access point image file in the TFTP server folder to c1140-k9w7-tar.default for a 11400 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1250-k9w7-tar.default for a 1250 series access point.
Step 5 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 6 Disconnect power from the access point.
Step 7 Press and hold MODE while you reconnect power to the access point.
Step 8 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 9 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 10 After the access point reboots, reconfigure it using the GUI or the CLI.
Similar Messages
-
Hello, I have a question on a Cisco AIR-LAP1242AG-A-K9 with LAP image it´s possible to load an Autonomous image?
I have done it but with Access Points that had form factory an AP image change it to LAP and then return the original AP image, but on an Access Point with LAP image from factory convert it to AP I´m not sure is possible.
Thaks.Yes, there are multiple ways of doing this.
this post describe one way of doing this. Hope that is useful
http://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/
HTH
Rasika
**** Pls rate all useful responses **** -
Convert from LAP to autonomous mode issue
I bought some after market 1242's for extended coverage in my warehouse. The current 1242's I have are all set up in autonomous mode.
When I console into the AP's I bought they are looking for a CAPWAP -Controller obviously from the previous environment. There is nothing on the AP or in the sh version showing LAP.
*Mar 1 00:46:37.102: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:46:38.104: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.xxx
*Mar 1 00:46:38.106: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.xxx
*Mar 1 00:48:38.106: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
#sh version
#Version 12.4(21a)JA2
System image file is "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx
I cant seem to be able to reset these to where they aren't looking for the Controller. I can login with the default username and password Cisco/Cisco but I cant do an erase. I get the privileged command prompt but cant do erase star or a config t??? Is there something I'm missing here that I need to to?
So far these commands have worked::
debug capwap console cli
debug capwap client no-reload
So can I downgrade or go back to autonomous mode or do I have to reload an IOS again? I don't have a license so my options there are limited.
Any ideas??? ThanksHI,
As pe your post:
System image file is "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx
This is lightweight image. for this image you need controller.
If you want to use as autonomous AP. Then you must convert it to Autonomous mode.
Autonomous image code : k9w7
More about images:
http://rscciew.wordpress.com/2014/01/04/understand-access-point-ios-images/
Here is the procedure to convert to autonomous :
https://supportforums.cisco.com/document/57476/lwapp-autonomous-conversion-and-vice-versa-access-points
http://paulbeyer.wordpress.com/2010/01/16/converting-a-cisco-ap-from-lwapp-to-autonomous-mode/
http://www.youtube.com/watch?v=QQ_NuxdRhQ4
Regards
Dont forget to rate helpful posts -
Hello Colleagues
Please there is any way to change the OS from LAP to Autonomous for lap1262nHello Driss,
Look steps:
Step 1 - The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 - Make sure that the PC contains the access point image file (such as ap3g1-k9w7-tar.124-25d.JA2.tar for a 1260 series access point) in the TFTP server folder and that the TFTP server is activated (set the timeout value on the TFTP server to 30 seconds).
Step 3 - On the PC where the TFTP server is located, perform these steps:
a. Disable any software firewall products, such as Windows firewall or others.
b. If you are using Windows -> Ensure all Windows files are visible. From Windows Explorer, click Tools > Folder Options > View; then uncheck the Hide extensions for known file types check box.
Step 4 - Rename the access point image file in the TFTP server folder to "c1260-k9w7-tar.default" for a 1260 series access point.
Step 5 - Connect the PC to the access point and disconnect power from the access point.
Step 6 - Press and hold MODE while you reconnect power to the access point.
Step 7 - Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8 - Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 - After the access point reboots and you completed work.
or
If you have one Controller working, you can downgrade by WLC also, check:
(Cisco Controller) >config ap tftp-downgrade your_ip ap3g1-k9w7-tar.124-25d.JA2.tar ap_name
Regards. -
Hi,
i was following cisco support community tread for how to chagne LAP1142N from LAP to Autonomous mode; was able to upload c1140-k9w7-tar.152-2.jb.tar to AP; AP boots with new image but i cannot access AP ove console port now.
Any ideas would be appreciated.
ThanksHere it goes, this is lgo capture during AP reset (press mode and power it on) and after one more reboot i initiated. Still not able to get to CLI over console.
Appreciate your assistance.
=================
using eeprom values
WRDTR,CLKTR: 0x84000800 0x40000000
RQDC ,RFDC : 0x8000003a 0x00000210
ddr init done
IOS Bootloader - Starting system.
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x84000800, 0x40000000
RQDC, RFDC : 0x8000003a, 0x00000210
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is up.
PCIE1: VC0 is active
PCIEx: initialization done
flashfs[0]: 30 files, 8 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32385024
flashfs[0]: Bytes used: 7425024
flashfs[0]: Bytes available: 24960000
flashfs[0]: flashfs fsck took 22 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 1111111111
Ethernet speed is 1000 Mb - FULL duplex
button pressed for 28 seconds
process_config_recovery: set IP address and config to default 10.0.0.1
process_config_recovery: image recovery
image_recovery: Download default IOS tar image tftp://255.255.255.255/c1140-k9w7-tar.default
examining image...
extracting info (277 bytes)
Image info:
Version Suffix: k9w7-.152-2.JB
Image Name: c1140-k9w7-mx.152-2.JB
Version Directory: c1140-k9w7-mx.152-2.JB
Ios Image Size: 9431552
Total Image Size: 10353152
Image Feature: WIRELESS LAN
Image Family: C1140
Wireless Switch Management Version: 7.4.1.37
Extracting files...
c1140-k9w7-mx.152-2.JB/ (directory) 0 (bytes)
c1140-k9w7-mx.152-2.JB/html/ (directory) 0 (bytes)
c1140-k9w7-mx.152-2.JB/html/level/ (directory) 0 (bytes)
c1140-k9w7-mx.152-2.JB/html/level/1/ (directory) 0 (bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/appsui.js (563 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/back.shtml (512 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/cookies.js (5032 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/1/forms.js (17492 bytes)...
extracting c1140-k9w7-mx.152-2.JB/html/level/1/sitewide.js (16554 bytes)...
extracting c1140-k9w7-mx.152-2.JB/html/level/1/config.js (25507 bytes).....
extracting c1140-k9w7-mx.152-2.JB/html/level/1/stylesheet.css (3220 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/popup_capabilitycodes.shtml.gz (1020 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/filter.js.gz (1862 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/filter_vlan.js.gz (1408 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/filter_mac_ether.js.gz (1793 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/security.js.gz (962 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/vlan.js.gz (959 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/ssid.js.gz (4151 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/1/dot1x.js.gz (988 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/network-if.js.gz (2084 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/stp.js.gz (957 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/ap_assoc.shtml.gz (5614 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/1/ap_event-log.shtml.gz (3907 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/ap_home.shtml.gz (6972 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/1/ap_network-if.shtml.gz (3565 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/ap_network-map.shtml.gz (3880 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/ap_services.shtml.gz (3697 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/ap_system-sw.shtml.gz (2888 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/ap_contextmgr.shtml.gz (3706 bytes)
c1140-k9w7-mx.152-2.JB/html/level/1/images/ (directory) 0 (bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/ap_title_appname.gif (2042 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/c1040_title_appname.gif (2058 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/apps_button.gif (1211 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/apps_button_1st.gif (1171 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/apps_button_cbottom.gif (318 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/apps_button_current.gif (1206 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/apps_button_endcap.gif (878 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/apps_button_encap_last.gif (333 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/apps_button_last.gif (386 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/apps_button_nth.gif (1177 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/apps_leftnav_dkgreen.gif (869 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/apps_leftnav_green.gif (879 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/apps_leftnav_upright.gif (64 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/apps_leftnav_yellow.gif (881 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/arrowdown_red.gif (108 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/arrowup_green.gif (108 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/corner_ur_7.gif (53 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/dkgreenmask11_up.gif (113 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/dkgreenmask28_upright.gif (110 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/grn_vertlines_bottom.gif (149 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/grn_vertlines_top.gif (141 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/hinav_plus.gif (56 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/left_bkg.gif (146 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/list_data.gif (122 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/logo.gif (29454 bytes)......
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/pixel.gif (49 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/sitewide_downleft.gif (53 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/sitewide_help_off.gif (934 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/sitewide_help_on.gif (934 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/sitewide_print_off.gif (111 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/sitewide_print_on.gif (111 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/spacer.gif (49 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/whitemask11_botleft.gif (62 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/whitemask11_upright.gif (61 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/event_alert.gif (73 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/event_critical.gif (73 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/event_debugging.gif (73 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/event_emergency.gif (73 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/event_error.gif (73 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/event_information.gif (73 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/event_notification.gif (73 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/event_warning.gif (73 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/check_mark.gif (71 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/background_web41.jpg (732 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/cisco-logo-2012.gif (579 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/1/images/logout_image.gif (40294 bytes)........
c1140-k9w7-mx.152-2.JB/html/level/15/ (directory) 0 (bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_assoc_adv.shtml.gz (4133 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_event-log_config-options.shtml.gz (5651 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_event-log_notif-options.shtml.gz (2683 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_express-setup.shtml.gz (11835 bytes)..
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_express-security.shtml.gz (13539 bytes)...
extracting c1140-k9w7-mx.152-2.JB/html/level/15/def_broadcast-ssid.shtml.gz (1263 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/def_no-security.shtml.gz (1582 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/def_eap-security.shtml.gz (1791 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/def_wep-security.shtml.gz (1597 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/def_wpa-security.shtml.gz (1854 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_network-if_ipaddress.shtml.gz (4594 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_network-if_802-11.shtml.gz (6308 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_network-if_802-11_b.shtml.gz (6265 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_network-if_802-11_c.shtml.gz (26662 bytes).....
extracting c1140-k9w7-mx.152-2.JB/html/level/15/dBm_mW_translation_table.shtml.gz (1511 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_network-if_802-11_d.shtml.gz (4059 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_network-if_ethernet.shtml.gz (4340 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_network-if_ethernet_b.shtml.gz (5488 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_network-map_ap-adjacent-list.shtml.gz (3795 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_sec.shtml.gz (7307 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_sec_ap-client-security.shtml.gz (26298 bytes).....
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_sec_ap-key-security.shtml.gz (12303 bytes)..
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_sec_band_select.shtml.gz (5699 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_sec_local-admin-access.shtml.gz (6978 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_sec_network-security_a.shtml.gz (10182 bytes)..
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_sec_network-security_b.shtml.gz (5594 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_sec_lrs.shtml.gz (5077 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_sec_lrs_b.shtml.gz (8514 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_sec_lrs_c.shtml.gz (6163 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_sec_ap-client-security-adv_a.shtml.gz (4973 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_sec_ap-client-security-adv_b.shtml.gz (5051 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_sec_ap-client-security-adv_c.shtml.gz (4658 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_sec_ap-client-security-adv_d.shtml.gz (3596 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_sec_ids_mfp.shtml.gz (3912 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_sec_ids_mfp_stats.shtml.gz (3642 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_sec_dot1x-security.shtml.gz (6432 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_sec_dot1x-certificates.shtml.gz (11155 bytes)..
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_sec_dot1x-cert_fingerprint.shtml.gz (577 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_services_arp.shtml.gz (3005 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_services_cdp.shtml.gz (5112 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_services_console-telnet.shtml.gz (6811 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_services_dns.shtml.gz (3575 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_services_filters.shtml.gz (5207 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_services_filters-ip.shtml.gz (8411 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_services_filters-mac.shtml.gz (3998 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_services_filters-ether.shtml.gz (3842 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_services_hot-standby.shtml.gz (5495 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_services_http.shtml.gz (5977 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_services_mobile-ip-b.shtml.gz (6656 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_services_mobile-ip-c.shtml.gz (4153 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_services_mobile-ip-d.shtml.gz (5159 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_services_mobile-ip.shtml.gz (6007 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_services_qos-traffic.shtml.gz (8125 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_services_qos.shtml.gz (12165 bytes)..
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_services_qos_adv.shtml.gz (4433 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_services_voice.shtml.gz (4079 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_services_voice-traffic.shtml.gz (6347 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_services_snmp.shtml.gz (8002 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_services_sntp.shtml.gz (5948 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_services_vlan.shtml.gz (12780 bytes)..
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_services_stp.shtml.gz (7107 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_stationview-client_ltest.shtml.gz (5514 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_system-sw_upgrade-b.htm (231 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_system-sw_upgrade-b.shtml.gz (6196 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_system-sw_upgrade.htm (229 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_system-sw_upgrade.shtml.gz (6238 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/banner.html (9573 bytes)..
extracting c1140-k9w7-mx.152-2.JB/html/level/15/frameAssociation.html (628 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/frameEventlog.html (627 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/frameHome.html (611 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/frameNetWork.html (619 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/frameSecurity.html (637 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/frameServices.html (651 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/frameSoftware.html (650 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/frameWireless.html (626 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/frameset.html (4394 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/navAssociation.html (897 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/navBar41.css (3605 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/navHome.html (1554 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/navNetwork.html (3935 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/navSecurity.html (2374 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/navServices.html (4508 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/navSoftware.html (1586 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/navWireless.html (1207 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/arrow_down.gif (177 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/arrow_down2.gif (838 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/arrow_right.gif (137 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/arrow_right2.gif (838 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/servicescript41.js.gz (12165 bytes)..
extracting c1140-k9w7-mx.152-2.JB/html/level/15/sideMenu.js.gz (813 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_easy-setup.shtml.gz (27004 bytes).....
extracting c1140-k9w7-mx.152-2.JB/html/level/15/navEventLog.html (911 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/content41.css (10497 bytes)..
extracting c1140-k9w7-mx.152-2.JB/html/level/15/logout.html (2369 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_system-sw_upgrade_poll.htm (234 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_system-sw_upgrade_poll.shtml (3596 bytes)
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_system-sw_sysconfig.shtml.gz (7145 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_stationview-client.shtml.gz (5554 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_contextmgr_ap.shtml.gz (4774 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_contextmgr_scm.shtml.gz (5294 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_contextmgr_scm-groups.shtml.gz (7511 bytes).
extracting c1140-k9w7-mx.152-2.JB/html/level/15/ap_contextmgr_scm_summary.shtml.gz (5061 bytes).
extracting c1140-k9w7-mx.152-2.JB/c1140-k9w7-mx.152-2.JB (9233742 bytes)...................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
extracting c1140-k9w7-mx.152-2.JB/8001.img (186220 bytes)........................................
extracting c1140-k9w7-mx.152-2.JB/T2.bin (8080 bytes).
extracting c1140-k9w7-mx.152-2.JB/T5.bin (23836 bytes).....
extracting c1140-k9w7-mx.152-2.JB/info (277 bytes)
extracting info.ver (277 bytes)
Deleting current version: flash:/c1140-rcvk9w8-mx...done.
New software image installed in flash:/c1140-k9w7-mx.152-2.JB
Configuring system to use new image...done.
Requested system reload in progress...download took about 387 seconds
Loading "flash:/c1140-k9w7-mx.152-2.JB/c1140-k9w7-mx.152-2.JB"...##############################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################
File "flash:/c1140-k9w7-mx.152-2.JB/c1140-k9w7-mx.152-2.JB" uncompressed and installed, entry point: 0x4000
executing...
enet halted
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 15.2(2)JB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:23 by prod_rel_team
Initializing flashfs...
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
flashfs[3]: found corrupted block[3] (byte 0, sector 0), fixing...
flashfs[3]: found corrupted block[4] (byte 0, sector 0), fixing...
flashfs[3]: 205 files, 13 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 32126976
flashfs[3]: Bytes used: 15453696
flashfs[3]: Bytes available: 16673280
flashfs[3]: flashfs fsck took 7 seconds.
flashfs[3]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 11999232
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 11998208
flashfs[4]: flashfs fsck took 1 seconds.
flashfs[4]: Initialization complete....done Initializing flashfs.
Radio0 present 8363 8000 90020000 0 90030000 B
Rate table has 80 entries (32 SGI/4 BF variants)
Radio1 present 8363 8000 98020000 0 98030000 0
Ethernet speed is 1000 Mb - FULL duplex
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-AP1142N-A-K9 (PowerPC405ex) processor (revision A0) with 81910K/49152K bytes of memory.
PowerPC405ex CPU at 586Mhz, revision number 0x147E
Last reset from power-on
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address:
Part Number : 73-11451-06
PCA Assembly Number : 800-30554-03
PCA Revision Number : A0
PCB Serial Number :
Top Assembly Part Number : 800-31273-01
Top Assembly Serial Number :
Top Revision Number : A0
Product/Model Number : AIR-LAP1142N-A-K9
Press RETURN to get started!
*Mar 1 00:00:10.177: %IFMGR-7-NO_IFINDEX_FILE: Unable to open nvram:/ifIndex-table No such file or directory
*Mar 1 00:00:10.181: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:10.183: *** CRASH_LOG = YES
*Mar 1 00:00:11.941: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:12.825: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1Base Ethernet MAC address: C4:7D:4F:3A:0E:D8
*Mar 1 00:00:13.032: not a autoconfig enabled device!!!
*Mar 1 00:00:14.973: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:15.973: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:01:01.900: Starting Ethernet promiscuous mode
*Mar 1 00:01:02.034: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 00:01:02.034: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Mar 1 00:01:02.051: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 15.2(2)JB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:23 by prod_rel_team
*Mar 1 00:01:02.051: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
*Mar 1 00:01:03.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:01:03.034: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:01:03.034: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:01:15.338: %CDP_PD-4-POWER_OK: Full power - INJECTOR_CONFIGURED_ON_SOURCE inline power source
using eeprom values
WRDTR,CLKTR: 0x84000800 0x40000000
RQDC ,RFDC : 0x8000003a 0x00000210
ddr init done
IOS Bootloader - Starting system.
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x84000800, 0x40000000
RQDC, RFDC : 0x8000003a, 0x00000210
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is up.
PCIE1: VC0 is active
PCIEx: initialization done
flashfs[0]: 205 files, 13 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32385024
flashfs[0]: Bytes used: 15454720
flashfs[0]: Bytes available: 16930304
flashfs[0]: flashfs fsck took 25 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: c4:7d:4f:3a:0e:d8
Ethernet speed is 1000 Mb - FULL duplex
Loading "flash:/c1140-k9w7-mx.152-2.JB/c1140-k9w7-mx.152-2.JB"...##############################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################
File "flash:/c1140-k9w7-mx.152-2.JB/c1140-k9w7-mx.152-2.JB" uncompressed and installed, entry point: 0x4000
executing...
enet halted
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 15.2(2)JB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:23 by prod_rel_team
Initializing flashfs...
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
flashfs[3]: 205 files, 13 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 32126976
flashfs[3]: Bytes used: 15454720
flashfs[3]: Bytes available: 16672256
flashfs[3]: flashfs fsck took 6 seconds.
flashfs[3]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 11999232
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 11998208
flashfs[4]: flashfs fsck took 1 seconds.
flashfs[4]: Initialization complete....done Initializing flashfs.
Radio0 present 8363 8000 90020000 0 90030000 B
Rate table has 80 entries (32 SGI/4 BF variants)
Radio1 present 8363 8000 98020000 0 98030000 0
Ethernet speed is 1000 Mb - FULL duplex
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-AP1142N-A-K9 (PowerPC405ex) processor (revision A0) with 81910K/49152K bytes of memory.
Processor board ID
PowerPC405ex CPU at 586Mhz, revision number 0x147E
Last reset from power-on
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address
Part Number :
PCA Assembly Number : 800-30554-03
PCA Revision Number : A0
PCB Serial Number :
Top Assembly Part Number : 800-31273-01
Top Assembly Serial Number
Top Revision Number : A0
Product/Model Number : AIR-LAP1142N-A-K9
Press RETURN to get started!
*Mar 1 00:00:08.849: %IFMGR-7-NO_IFINDEX_FILE: Unable to open nvram:/ifIndex-table No such file or directory
*Mar 1 00:00:08.853: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:08.854: *** CRASH_LOG = YES
*Mar 1 00:00:10.613: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:11.497: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1Base Ethernet MAC address: C4:7D:4F:3A:0E:D8
*Mar 1 00:00:11.703: not a autoconfig enabled device!!!
*Mar 1 00:00:13.644: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:14.644: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:01:00.572: Starting Ethernet promiscuous mode
*Mar 1 00:01:00.707: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 00:01:00.707: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Mar 1 00:01:00.722: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 15.2(2)JB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:23 by prod_rel_team
*Mar 1 00:01:00.722: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
*Mar 1 00:01:01.698: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:01:01.707: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:01:01.707: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:01:13.444: %CDP_PD-4-POWER_OK: Full power - INJECTOR_CONFIGURED_ON_SOURCE inline power source
=================================================== -
I was setting up the APs for a new users lab when we discovered they had puchased LAPs instead of APs.
I installed the current version of the IOS following the procedures outlined in "Converting a Lightweight Access Point Back to Autonomous Mode" on Cisco's website. However, they're just not behaving correctly.
Before going further, can LAP1131s be converted to autonomous mode? Or is it only AP1131s that can be converted back and forth?
Thanks,
ChrisHi Chris,
One thing to note that on the newer IOS's the Radio's cannot be enabled until the SSID is set. You may have been seeing this result;
Changes to the Default Configuration-Radios Disabled and No Default SSID
In this release, the radio or radios are disabled by default, and there is no default SSID. You must create an SSID and enable the radio or radios before the access point will allow wireless associations from other devices. These changes to the default configuration improve the security of newly installed access points.
http://www.cisco.com/en/US/docs/wireless/access_point/ios/release/notes/b38jebrn.html#wp147963
Hope this helps!
Rob -
I have Cisco AIR-LAP1131G-E-K9 but now I want to convert it to Autonomous. I am trying the method of IOS upgradation the way mention on the forum and cisco site but I am not able to do that.
process_config_recovery: set IP address and config to default 10.0.0.1
process_config_recovery: image recovery
image_recovery: Download default IOS tar image tftp://255.255.255.255/c1130-k9w7
-tar.default
examining image...
%Error opening (no such file or directory)Loading "flash:/c1130-rcvk9w8-mx/c113
0-rcvk9w8-mx"...################################################################
I have downloaded the c1130-rcvk9w8-tar.124-21a.JA and rename it c1130-rcvk9w8-tar.default but i am getting the above mention error.
As per the fourm discussion teh image should be like that c1130-k9w7-tar.default but mine is look like that c1130-rcvk9w8-tar.default.
I searched everywhere to find exact version but unable to find it. Cisco has changed the pages. Please let me know from where I can download the exact image.
I am downloading this image from wirless IOS where conversion method is mentioned. I am downloading coversion IOS not the normal.
Pleaase help me out to solve this problem.You need to download an IOS software and rename it to c1130-k9w7-tar.default... Just like what it states in the log.
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp161272 -
Converting 1242AG LAP to autonomous
Hi,
I have a second hand air-lap1242AG (basically aironet 1200series - configured to lightweight mode). I would like to configure it in a small business. We have a Linksys WAG354G (Wireless-G ADSL Gateway), which has 4 ethernet ports. It has a really small range. The problem is now, to connect those two. I tried already resetting the aironet(holding mode for 3 sec, also tried to rewrite the image-holding it for 20s), but when I look on my linksys DHCP-page, it still shows me the same client host name of the aironet, as when I first plugged it in. Its the name of the company, it belonged to, before us.
The error reported by the LEDs is - Alternating green, red , and amber, when you look here: http://www.cisco.com/en/US/products/ps6521/products_installation_guide_chapter09186a008079b730.html
So I guess, since the DHCP is working fine - the IP adress is assigned, the only problem is, that the previous settings are still active - which means it doesnt allow to connect to the new router/controller.
What can I do about that? Converting to autonomous mode? I didnt try it, because it seems extremely complicated to me. Im not an IT-pro.
Thanks a lot
Solved: Sorry for bothering, I thought I wont be able to do it. The explanation of the conversion is so stupid! I managed to do it through TFTP. First I was confused with the renaming, but I finally got it, that in the guide its only an example...
byeYou need to download an IOS software and rename it to c1130-k9w7-tar.default... Just like what it states in the log.
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp161272 -
Hi ,
I have 1042 Light weight AP and i want to convert it to Autonomous mode . i dont find any particular image for this conversion ..when i try to find autonomous image for 1040 its showing "c1140-k9w7-tar.124-25d.JA1.tar"........can i use this image ?...Yes. You can use the IOS file for the 1140.
Using a TFTP Server to Return to a Previous Release -
1142 Lightweight to Autonomous
Hello all,
I am trying to convert an 1142 from lightweight to autonomous. I've found this post:
https://supportforums.cisco.com/thread/2055997
However the following command is not available via the CLI: archive download-sw /overwrite tftp://
Any thoughts?
Thank you,
JeffHello
I am using Product/Model Number: AIR-LAP1242AG-N-K9 with following IOS information:
BOOT path-list: flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx
Config file: flash:/config.txt
Private Config file: flash:/private-config
Enable Break: no
Manual Boot: no
Enable IOS Break: no
HELPER path-list:
NVRAM/Config file
buffer size: 32768
Mode Button: on
Now I want to convert this to Autonomous mode but command
"debug capwap console cli
or
debug lwapp console cli"
are not working. Could you please confirm the command for converting LWAP to Autonomous AP for the mentioned IOS
Regards,
Manish Sharma -
Lightweight AP to Autonomous conversion without Controller
Dear Folks,
I do have 1131 LWAPP in home, i was wondering if i can convert to Autonomous . I read in the documentation, that only way is to use with controller. Is it true ? or can i convert without connecting to WLC .
SID1) Go to your Computer and from the tool menu -> folder options ->uncheck the hide extensions for known file types option.
2) Download the IOS image ( you can get this ios image from cisco.com) on your desktop.
3) Rename the image into c1130-k9w7-tar.default
4) Give your computer Ethernet an address in the range 10.0.0.2 till
10.0.0.30
5) Run the tftp server on your computer.
- Make sure that the directory of your tftp server is the desktop.
- Specify the AP address on the tftp server if needed.
6) Connect the AP to the computer with Ethernet cable.
7) Remove the power from the AP.
8) Press and hold Mode button on the AP, and insert the power jacket in the AP.
9) Keep pressing on the Mode button for (20-30 seconds) until you see RED Led.
10) Wait until the image installed and all led lights return to green -
[Q] Maximum Number of Concurrent Connections to 1142 LAP
We are having random issues of users not being able to connect to our wireless network consistently. The users will have successfully accessed the network previously but then will have difficulty associating to the network. After a period of time, the association appears successful again. My first thoughts were that there was a restriction on the number of clients that could associate to a given AP at any one time.
This is the equipment we have:
1x Cisco Wireless Control Server (WCS) 6.0.181.0
4x Cisco 5508 Wireless LAN Controllers 6.0.196.0
60x Aironet 1142N Lightweight Access Points (LAP)
Is there a hard or recommended maximum number of clients per LAP? If so, where is this defined? From what I have read on these forums, Cisco apparently recommends about 25 clients per AP but I can not find any official documentation to support this.
When I go to WCS Home > General > Top APs by Client Count, the top AP reports 20 clients. However, if I click on the AP Name and go to the Current Associated Clients tab, it is only listing 8 clients - why is this?
Any help greatly appreciated.
Thanks in advance.1. What error messages do the clients get when they are having association/authentication issues?
There is no error message on the client, it simply fails to connect instantly. On an Android phone, you see it constantly trying to connect, failing and trying to reconnect. After many attempts (at least 10) it may connect successfully. This appears to me that it may be related to aggressive load balancing - here is what I think may be happening:
Client tries to connect to nearest LAP
Nearest LAP has to many clients on associated (as detemrined by the RRM Thresholds > Max Clients setting) and so refuses the connection (and sends a code 17 response)
Client attempts to connect to the next nearest LAP which is also too busy. It too rejects the connection.
Client attempts to connect to the third nearest LAP which is also too busy. It too rejects the connection.
And so on until it comes back to the first nearest LAP
This LAP, which still has too many associated clients, rejects the connection for a second time (its RRM Thresholds > Min Failed Clients is set to 3)
the clients tries the other APs and is also rejected as they are all set to reject connections for 3 times.
Client goes round all the APs for a third time. still getting rejected.
It then attempts a 4th connection to the nearest LAP and is allowed to associated as it is beyong the 3-attempt threshold for rejected connections.
This is my understanding of Aggressive Load balancing and would seem to match the observed behaviour of the clients but I would like to know if this is correct and how I can verify that in the logs?
This goes back to my first question, what is the max recommended number of clients for a 1142N LAP? Furthermore, is there any supporting documentation for this recommendation? Also, if I increase the RRM threshold Max clients to more than its default of 12, will the LAP accept more connections before rejecting them?
I would also like an answer to my second question in the original post.
2. Are you using ACS/RADIUS/TACACS?
We are using 802.1X with ACS for our corporate users on the corporate SSID but the behaviour described above is seen on guest clients that just use web passthrough (i am not sure if it is also on corporate clients, I have not seen any reports to that effect yet). -
Cisco Aironet 1200 LAP Issues - LAP to Autonomous Mode
Greetings! After purchasing 4 of the Cisco Aironet 1200 G Series WAPs, I'm now running into a slight issue with them.
I received these last week with the understanding that if I didn't have the Cisco controller device, I could convert them from being the Lightweight Access Point, back to Autonomous mode with an IOS.
With this, I checked the documentation that came with the device and found the "Upgrading Autonomous Cisco Aironet Access Points to Lightweight Mode" or http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=Getting%20Started%20with%20Wireless&needs_authentication=yes&CommCmd=MB%3Fcmd%3Dadd_discussion%26mode%3Dshow%26needs_authentication%3Dyes%26location%3D.ee7c7c3.
From there, I followed the instructions listed under Converting a Lightweight Access Point Back to Autonomous Mode. Before the rename of the file, I checked the device and found AIR-LAP1242G-A-K9 for the Model No.
One of the Cisco Certified admins here was able to obtain the latest build for the IOS for the device or c1240-k9w7-tar.123-8.JEB1.tar. Per the instructions, I renamed the file to coincide with the model of the device.
I followed the instructions from there, and it looked as if everything was going well. However, after the upgrade, I'm running into an issue with the following:
File "flash:/c1200-k9w7-mx.123-8.JEB1/c1200-k9w7-mx.123-8.JEB1" uncompressed and installed, entry point: 0x3000
executing...
At this point, the device just locks up. All lights are lit green on the device. According do the documentation, it should reboot and from there, I should be able to access the web interface by IP.
I've tried to perform the upgrade again using the same IOS build, but the same thing happens with the lock up.
At this point, I'm assuming the issue is with the build of the IOS that I have and I may have to look at getting an older build. However, before doing so, I thought I would post something here to see if anyone had an idea.
I may have needed to refine my searching of the forums, but wasn't able to find anything in relation to my issue. If there is something out there, I do apologize for the post and will happily refer to any current information.
If you need any further information in relation to this, please let me know. Any assistance is greatly appreciated. Thank you!Hi Jeffrey,
Reverting the Access Point Back to Autonomous Mode
Have a look at Step 3
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold MODE while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
Hope this helps!
Rob -
Have 1142 LAP AP's installed in each floor, All AP in One specific Floor are rebooting. After reboot most AP are joining WLC but few are unable to Join WLC. Logs in WLC shows AP has Crashed due to
"Unexpected exception to CPUvector 2000, PC = 0x49DFE8 , LR = 0x49DFFC : Unexpected exception to CPUvector 2000, PC = 0x49DFE8 , LR = 0x49DFFC"
and
"Last AP disconnect details
- Reason for last AP connection failure.................... Data transfer message received from an unsupported AP
Would like to i) debug further for reason of AP reload ii) Reason for AP not joining WLC after reload /crash.
Is there way to collect AP debugs from WLC ? Any suggestion to prevent reloads from happening.This is bug CSCtx92385, No workaround yet
Saurav,
Whoever created updated the bug needs to review the accuracy of the content. Under the Details > Product it states AP is a 2700. Under Details > Known Affected Release it states "7.0(116.0)". -
How to go in GUI mode of AIR-LAP 1131AG-A-K9 standlone
i am using above model of access point without controller.For that we tried to convert LAP to autonomous mode but didnt get success.Here is log viewer of tftp server.
Connection received from 10.0.0.1 on port 1024 [29/01 19:19:29.156]
Read request for file <c1130-k9w7-tar.default>. Mode octet [29/01 19:19:29.171]
Using local port 1112 [29/01 19:19:29.171]
TIMEOUT waiting for Ack block #1 [29/01 19:19:44.171]What i understand you want to convert from Lightweight mode to autonomous mode .. without controller
Link to download tftp server
http://tftpd32.jounin.net
Link to download AP image you to upload:
http://tools.cisco.com/support/downloads/pub/Redirect.x?mdfid=278875243
Here is the step that you can try :-
LWAPP to autonomus AP converstion steps
Here is a example steps for you:
Step 1 The PC you intend to use must be configured with a static IP address in the range of 10.0.0.2 to 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1100-k9w7-tar.122-15.JA.tar for an 1100 series access point or c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1100-k9w7-tar.default for an 1100 series access point or c1200-k9w7-tar.default for a 1200 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power (the power jack for external power or the Ethernet cable for in-line power) from the access point.
Step 6 Press and hold the MODE button while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds), and release the MODE button.
Step 8 Wait until the access point reboots as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, you must reconfigure the access point by using the Web-browser interface or the CLI.
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_guide_chapter09186a0080209250.html#wp1040300
Hope this helps! ..
Pls rate if it resolve ur issue so that others can also benefit from these steps.
Thanks,
Manjeet Singh
Maybe you are looking for
-
My MacBook is almost almost two years old and I've had a ton of problems with it. It started out with the colored palmrests and "mooing" fan, then I had a crash after a firmware update. About four months ago I had to replace the SuperDrive because it
-
The "new" hotmail no longer works with safari, but works with firefox. Hmm.
The "new" hotmail no longer works with safari, but works with firefox. Hmm. i find this very convenient being a microsoft product. anybody else wonder why this new version happens to not be safari compatible? does anybody know if it works on the PC v
-
Hello today I received my L540 and I'm installing all the drivers at the moment. After I installed the trackpad/point drivers I disabled the trackpad. But now I noticed that the middle mouse button isn't working. How can I fix this issue? Also is the
-
UDF to compare two values and Pull another value if equals
Hi all, I am looking for UDF to perform the following logic, please help me I will have 3 inputs, say field1, fields2, field3. If field1 = field2 then return field3. You may say that this can be implemented by message mapping with IF condition itself
-
Upload values from vb to tables bapi
Hi All, I am uplaod the values as imports for a table in a bapi using bapi oFunction.exports("field_name") is working fine now i want to send the values to a table which is a export for the bapi I am using the below code but i am getting an error mes