1142LAP not joing the controller after conversion

I have some remote 1142s that I converted to LAP last night.  They are not joing a WLC, but I they are online and I can ping them.  Telnet or SSH is disabled by default (WHY???). What can I do to figure out why these access points are not joining the controller?                  

How are the APs getting IP address information and controller IP information?
The APs have static IP addresses and should be getting controller IP info through DNS. There is an entry cisco-capwap-controller pointing to one of our WLCs and I can ping it from the switch where the AP is connected. I also have DHCP Option 43 setup should the LAP decide to relase its static IP and get a DHCP IP address.
Your switch ports were probably configured as trunk ports. Have you changed them to access ports?
The switchports were configured trunks. I've since changed one to an access port.
Can the VLAN interface at the remote site ping the management interface of the controller?
Not sure how to do this from the specific VLAN interface at the remote site.  I can ping the management interface from the switch that host the VLAN interfaces.
What's the controller type and code?
5508  ver 7.3.101.0
Can you console into an AP, reboot it and capture the output and post it on here? I assume this will be a problem since they are remote.
AP is in a remote location. YES THIS IS THE PROBLEM...
I need to get several of these APs converted at several locations.  It's a roll of the dice with ever AP I try to convert.  Theres got to be an easier way that doesn't involve several road trips.

Similar Messages

  • AP is unable to associate. The Regulatory Domain '-E' configured on interface '802.11a' does not match the Controller Regulatory Domain '-C'

    Hi,
    There are three different types of APs associated with controller and working fine.
    1.       AIR-LAP1252AG-E-K9
    2.       AIR-LAP1522AG-E-K9
    3.       AIR-CAP1552E-C-K9
    WLC is AIR-CT5508-K9. Software version is 7.4.100.0. Field Recovery Image is 7.0.112.21. Firmware version is FPGA 1.7, Env 1.8, USB console 2.2. WCS is 7.0.240.0 for Windows.
    WCS is sending alarms for AIR-LAP1522AG-E-K9:
    Message: AP is unable to associate. The Regulatory Domain '-E' configured on interface '802.11a' does not match the Controller Regulatory Domain '-C'.
    Before Controller was 7.2.4 (not sure).
    Country configured on WLC is AE and shows -CE regulatory domain. Mesh APs are also associated.
    I believe this Critical alarm should not come.
    how much is this alarm important? What should be done to resolve this?

    Typically you still need to make sure that the country codes are indeed configured on the WLC. Thing can change when you upgrade code as standards might of changed and regulations also. If your AP's are functional, then you should be okay and I wouldn't worry too much about it, but if after the upgrade, the WLC complains about country code stuff, then you just need to verify that the AP's country code is defined on the WLC. May times the AP will not join and if it does join, the radios might be disabled or in a down status.
    Sent from Cisco Technical Support iPad App

  • LAP 2702 %CAPWAP-1-ARP_ERROR: Could not arp the controller ip address, retry later

    I am reusing one of the AP which was previously connected to WLC2504. 
    So I rename the AP and reconfigure the IP address to point to a new WLC8510. The AP and WLC is under same vlan 252.
    At first it has joined the new WLC but it keeps disconnected from wlc and reconnect again after awhile.
    AP is showing this error :
    %CAPWAP-1-ARP_ERROR: Could not arp the controller ip address, retry later
    My AP ip address is 172.16.54.171/23
    If i try to ping the ip from the same subnet, the AP has no timeout. but if I telnet into this AP and ping to wlc, it is intermittent. 
    Any idea what is the issue?

    Rasika,
    I have the same issue on my home 2504 with these 2700 UX, I have tried code 8.0.100.0, 8.0.110.0 (Docs say this is the min version supported), and even 8.0.115.0 (latest available) still no dice. The AP won't register, and gives the error stated above. I am seeing 2 images available for the AP, the AP shipped with the later image but  I AP recovery isn't working because it say's unable to find image with XX in the name? I see the TFTP logs, and name the file accordingly no dice, then the unable to find file name -XX pops up too. As you know I am busy during the day this week, but let's jump on a skype and take a look later maybe you have seen something I haven't?
    For good measure, also attempted to join a 3650 here at the house IOS-XE 3.6 no dice, going to try 3.7 too tomorrow, It worked for the 3700 UX AP's we had??

  • HT3986 I have a pc that is one year old and the hard drive is crashing we use it only for quick books to run our small business I would like to buy amac and install the OS  forom the pc to the apple product i will not use the pc after can i use the OS off

    I have a pc that is one year old and the hard drive is crashing we use it only for quick books to run our small business I would like to buy a macmini and install the OS  from the pc to the apple product i will not use the pc after, can i use the OS off the pc or do I have to purchase another?

    I think you can get Windows 7 for around $99. Install the 64bit version as the 32bit version will not be able to use all your new computer's ram if you have more than about 3.5gb.
    Back up your quick books data now before the old hard drive dies. You can copy your data over to your new installation of Windows and quick books.
    By the way, there is quick books for Mac http://quickbooks.intuit.com/mac/?sc=BNR-000-COR-quickbooks&priorityCode=4902000 000&cid=ppc_google_QB-Intuit-Core-Brand-Mac_quick-books-for-mac_exact&site=&ad_i d=9347918288&raw_keyword=quick%20books%20for%20mac
    So you may not need to install Windows at all.

  • LAP not joining the controller

    Gents
    I have 1 AP out of ten not joining the controller. I connected the access point to the network and I checked its boot. the access point reaches LWAPP Discovery" and then give me console input. I hard reset the access point and I hard coded an IP address for the AP the AP joins the controller, but when I reset it to assign it to another controller it did not join again.
    why the discovery process is not showing the DHCP option 43 configured and DNS for CISCO-LWAPP-CONTROLLER configured on the DNS. All the access point is operating normally except this one. it has many certificate inside, why a hard reset did not work to solve the problem?
    Please advise
    Thanks,

    Does the LAP have a valid IP address?
    Can the LAP ping the WLC managment IP address?
    Console into the LAP and in enable mode, type the command "lwapp ap controller ".

  • Mail does not load the mail after opening with 10.10.3 on macbook air

    Mail does not load the mail after opening with 10.10.3 on macbook air

    Under Window in the Menu bar select Connection doctor. You will see green to indicate a connection and red to show there is a problem. Except for iCloud account you'll see two entries for each account 1) receiving and 2 SMTP for sending.
    If it's red, this usually means it's missing the password.
    For Incoming messages, set in the account window, under Account Information tab.
    For Outgoing (SMTP) messages, follow these steps:
    EDIT SMTP SETTINGS
    In Accounts window > Outgoing Mail Server SMTP:  select to Edit SMTP Server list... from popup.
    Select account in the list.(It's not uncommon to find extra SMTP servers listed. When you remove account, Mail does not delete the smtp info. You might need to do some clean up in the list to remove the extras.)
    Under Advanced Tab:
    Apple defaults to the default ports (25,465, 587) but some servers prefer a custom port. Check to see what port they recommend. Gmail for example likes 465, Outlook.com 587.
    Verify if your server require SSL.
    User Name. Enter full email address  eg.  [email protected]
    Add password if it is blank.(If you have two step authentication setup, you'll need to get an app specific password  more info)
    Open Connection Doctor under Window in the Menu bar.
    Do you see green light now for your account SMTP?

  • HT4461 I can not download the APP after payment

    I can not download the APP after payment

    Hi there qsx,
    You may want to try downloading the app again via Past Purchases.
    Downloading past purchases from the iTunes Store, App Store, and iBooks Store
    http://support.apple.com/kb/ht2519
    -Griff W.

  • I can not install the Express after the Extreme tha AirPort tool is of no help. It does not display any base station.

    I can not install the Express after the Extreme tha AirPort tool is of no help. It does not display any base station.

    What is the exact model of the AirPort Express that you are trying to install? Which version of the AirPort Utility are you using? What is the operating system and version, and on what device, are you running the AirPort Utility on?

  • I could not activate the phone after updating software to iOS7.

    Dear Apple Support team.
    Please help to investigate the problem as I could not activate the phone after updating software to iOS7. in the phone the erroe message is "Your iPhone could not be activated because the actiovation server cannot reached. Try connecting your iPhone to iTunes to activate it, or try again in a couple of minutes.
    I have try to activate both of way such by WiFi & Cellular activation and connecting with iTunes but still face the problem and could not completed activation the phone.
    How do i activate the phone or have to wait for hour not couple min as you suggested.
    your feedback quickly would be appreciated.
    Thank You
    Kritpas

    There is nothing you can do. That is the Activation Lock that Apple has implemented tout down on theft of their iPhones.
    Most likely the iPhone is stolen.
    It is totally worthless to you.

  • Someone changed my icloud login password, and I can not activate the iPhone after   recovery

    someone changed my itslud login password, and I can not activate the iPhone after
      recovery

    You could try to reset your password via a webbrowser here: https://appleid.apple.com

  • When I try to install WinXP using bootcamp, the iMac will not recognize the CD after it has already read all the information and is ready to begin installation. What is the problem?

    When I try to install WinXP using bootcamp, the iMac will not recognize the CD after it has already read all the information and is ready to begin installation. What is the problem?

    If your on 10.6.8 like you should be for security/stability updates, somewhere along the line a later Bootcamp version was issued and only supports Win 7.
    You can read my post here for a alternative solution, running a virtual machine software
    https://discussions.apple.com/thread/3772839?tstart=0

  • APs not associating with Controller after upgrade

    This is pretty bad.
    I've been upgrading our controllers to 4.2.209.0 without any problems untill today. The controller upgraded fine but, the APs aren't showing up anywhere. They aren't associating with any controller. I've shut/no shut the PoE ports. They show connected. The WCS says they are not associated with any controller. What should I do. Roll back the image? Will this help?
    Thanks Pat.

    Surendra,
    Thanks for the response. I got this from debug dhcp detail
    DHCP: QScan: Timed out Selecting state%Unknown DHCP problem.. No allocation possible
    I was pretty desparate at the time so, I wasn't able to trouble-shoot any further. After I saw the DHCP debug I deleted the normal DHCP server address, created a scope for the APs and configured it on the AP management interface and the APs got addresses. After the APs got their addresses, the clients got their addresses from the regular DHCP server. I will try again with the upgrade as I rolled back to 4.2.112.0. Atleast I know I can get an ip from the controller if I need.
    Do you know of any reason why my APs weren't getting addresses. Even when I rolled back they weren't getting addresses. The config hadn't changed.
    Thanks, Pat.

  • APs randomly will not join the controller

    Hi all,
    In short, APs will join the controller immediately using the recovery image, but once it downloads 7.6.100 and reboots, it either cannot join the controller or will take up to 40 minutes.
    The AP is in local mode. The AP 1040 eventually joined the controller, 40 minutes after we deleted all the files off the flash which is unacceptable.
    *Apr  9 15:38:15.842: %CAPWAP-5-SENDJOIN: sending Join Request to 10.10.10.10
    *Apr  9 15:38:15.851: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
    *Apr  9 15:38:15.851: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
    *Apr  9 15:38:15.851: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Apr  9 15:38:15.851: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.10.10.10
    *Apr  9 15:38:16.304: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
    *Apr  9 15:38:16.362: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Apr  9 15:38:16.427: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller CONTROLLER-DC
    I also had our technician console into a 2602 and we were seeing exact same errors.
    SUMMARY OF THIS CASE:
    --AP is 1042 and wlc is on 7.6.100.0
    --using dhcp option 43 but the AP has static ip
    --checked the private config on the AP and it was not sending the discovery request to the desired  WLC
    --cleared the private config
    --primed the AP to desired WLC
    --AP sending join request but receiving the following errors:
    Apr  4 14:37:47.000: CAPWAP-3-ERRORLOG Go join a capwap controller
    *Apr  4 14:36:47.000: CAPWAP-5-DTLSREQSEND DTLS connection request sent peer_ip: 10.10.10.11 peer_port: 5246
    *Apr  4 14:36:47.169: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_handshake.c:90 First fragment for seq 2 is missing
    *Apr  4 14:37:17.205: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
    --cleared the flash except rcv
    --ap started downloading the image from the wlc but once it reboots the same errors appear again
    --research made on the error message and apparently we are hitting a bug:
    https://tools.cisco.com/bugsearch/bug/CSCul08933/?reffering_site=dumpcr

    Hi Leo,
    Next the information, I omitted some serial number and descriptions due to confidentiality matters.
    (Cisco Controller) >show sysinfo
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller Product Version.................................. 7.6.100.0 Bootloader Version............................... 1.0.1 Field Recovery Image Version..................... 6.0.182.0 Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27 Build Type....................................... DATA + WPS
    System Name...................................... ABCDEF System Location..................................
    System Contact...................................
    System ObjectID.................................. 1.3.6.1.4.1.9.1.1069 Redundancy Mode.................................. Disabled IP Address....................................... XXXXXXX Last Reset....................................... Software reset System Up Time................................... 32 days 14 hrs 1 mins 41 secs System Timezone Location......................... (GMT -5:00) Eastern Time (US and Canada) System Stats Realtime Interval................... 5 System Stats Normal Interval..................... 180
    Configured Country............................... CA  - Canada Operating Environment............................ Commercial (0 to 40 C)
    Internal Temp Alarm Limits....................... 0 to 65 C Internal Temperature............................. +40 C External Temperature............................. +21 C Fan Status....................................... OK
    State of 802.11b Network......................... Enabled State of 802.11a Network......................... Enabled Number of WLANs.................................. 5 Number of Active Clients......................... 2215
    Burned-in MAC Address............................ F0:F7:55:2B:4A:80 Power Supply 1................................... Present, OK Power Supply 2................................... Absent Maximum number of APs supported.................. 500
    (Cisco Controller) >show time
    Time............................................. Mon Apr 14 08:40:08 2014
    Timezone delta................................... 0:0 Timezone location................................ (GMT -5:00) Eastern Time (US and Canada)
    NTP Servers
        NTP Polling Interval.........................     36000
         Index     NTP Key Index                  NTP Server                  NTP Msg Auth Status
           1              0                                              A.B.C.D                        AUTH DISABLED
    AP>sh ver
    Cisco IOS Software, C3500 Software (AP3G1-K9W8-M), Version 15.2(4)JB3, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2013 by Cisco Systems, Inc.
    Compiled Wed 18-Dec-13 21:36 by prod_rel_team
    ROM: Bootstrap program is C3500 boot loader
    BOOTLDR: C3500 Boot Loader (AP3G1-BOOT-M), Version 15.2 [chayan-apn-0411 116]
    AP uptime is 2 days, 17 hours, 15 minutes System returned to ROM by reload System image file is "flash:/ap3g1-k9w8-mx.152-4.JB3/ap3g1-k9w8-xx.152-4.JB3"
    Last reload reason:
    cisco AIR-CAP3502I-A-K9 (PowerPC460exr) processor (revision A0) with 98294K/32768K bytes of memory.
    Processor board ID XXXXXXXX
    PowerPC460exr CPU at 666Mhz, revision number 0x18A8 Last reset from reload LWAPP image version 7.6.100.0
    1 Gigabit Ethernet interface
    2 802.11 Radios
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 70:81:05:9E:F7:36
    Part Number                          : 73-12175-05
    PCA Assembly Number                  : 800-32268-05
    PCA Revision Number                  : A0
    PCB Serial Number                    : XXXXXXX
    Top Assembly Part Number             : 800-32891-01
    Top Assembly Serial Number           : FGL1534S7LP
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-CAP3502I-A-K9  
    Configuration register is 0xF
    AP>sh ip int br
    Interface                  IP-Address      OK? Method Status                Protocol
    BVI1                       X.Y.W.Z                YES TFTP   up                    up     
    Dot11Radio0                unassigned      NO  unset  up                    up     
    Dot11Radio1                unassigned      NO  unset  up                    up     
    GigabitEthernet0           unassigned      NO  unset  up                    up     
    GigabitEthernet0.1         unassigned      YES unset  up                    up     
    AP>sh inventory
    NAME: "AP3500", DESCR: "Cisco Aironet 3500 Series (IEEE 802.11n) Access Point"
    PID: AIR-CAP3502I-A-K9 , VID: V01, SN: XXXXXXX

  • 1131 and 1141 APs not finding the controller

    We have deployed about 40 of these and about half have found the controller. The others have not. I have used option 43 in the past but lately they were able to find the contrller without that. I also took out the lwapp-controller name out of dns as we have 4 buildings of these etc. Should I put the controller name in dns and what is that default name.
    thanks
    Gary

    If the AP's are not on the same subnet as the controller, and you are not using Over the Air Provisioning, then you need to use DHCP Option 43, put your DNS entry back in, or set the controller address manually via the console port on the AP.
    The host name for the DNS entry is CISCO-LWAPP-CONTROLLER. If you're adding that entry, then you might want to also add CISCO-CAPWAP-CONTROLLER pointing to the same address. While I believe that all current AP's will try to resolve CISCO-LWAPP-CONTROLLER (even if they are CAPWAP APs), this may not be the case in the future.
    We use the DNS feature and then set the AP's appropriate primary/secondary controller after it joins.
    Here's a good article about the AP join process:
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a00806c9e51.shtml
    Here's a good article about troubleshooting AP's that won't join:
    http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a00808f8599.shtml

  • My daq 6008 wil not drop the 5V after the VI is stopped, i have a digital signal going from the error out on the daq in the while loop to the error in on the daq outside the while loop and a boolean going to the data of the daq outside

    my daq 6008 wil not drop the 5V on a digital output after the VI is stopped, i have a digital signal going from the error out on the daq in the while loop to the error in on the daq outside the while loop and a boolean going to the data of the daq outside, but i can t seemto get it to work

    i attached the block diagram so you can have a look
    Attachments:
    PID Temp control.docx ‏120 KB

Maybe you are looking for

  • ITunes will not start...

    I have installed and uninstalled iTunes numerous times and followed the troubleshooting guide on the support page. Every time iTunes is finished installing it says "iTunes has encountered a problem and needs to close" and then I have the option to se

  • Database Expert -- Views at End of Alpha List Do Not Appear

    I'm working with an MS-SQL database. All the table in it, from A to Z show up.  The DB vendor wants us to use views to access data for reports, however.  And looking at the list of views in the Database Expert -- the list is cut off in the vwRs.  So

  • Saving default values for checkboxes

    Hi all, one of our customers has recently upgraded ´their NW7.00 (SAP ECC 6.0) system to basis SP18. As a result of this, it is no longer possible for users to save default values, in Web Dynpro ABAP applications, neither for checkboxes nor for radio

  • IMPORT ERROR for .dmp file

    Hi, I am getting this error, when I try to import a .dmp file: ERROR: Message 100 not found; No message file for product=RDBMS, facility=IMP: Release 9.2.0.1.0 - Production on Wed May 23 15:35:53 2012 Copyright (c) 1982, 2002, Oracl Invalid format of

  • Photoshop Elements 10 working only once

    Something has happened to my Photoshop Elements 10 ... it works once when I first use it .... it will not work the second time. Restarting my computer brings it back. The recently added Win 7 64 bit box "Do you want to run this Program" box does not