1142N radios won't turn on

Hello, Wifi Experts!
Received 20 1142N AP's
19 were registered and working with the Controller code version 7.3.101.
One was DOA so we had it RMA'd.
Replacement came, with same part number.
Plugged it in into the network.
Successfully registered to the controller.
BUT ITS RADIOS WON'T TURN ON!
802.11B/G was configured 'Enabled' but its status is 'Disabled'.
plugged it on a switch where one of the working AP's is connected.
switchport configs are identical for these two AP's.
and still the radios won't turn on.
Any birght ideas, experts!!!

Thanks, Leo, for your reply.
Here is the AP boot capture:
using eeprom values
WRDTR,CLKTR: 0x87000800 0x40000000
RQDC ,RFDC : 0x80000036 0x00000208
ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x87000800, 0x40000000
RQDC, RFDC : 0x80000036, 0x00000208
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is up.
PCIE1: VC0 is active
PCIEx: initialization done
flashfs[0]: 27 files, 9 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32385024
flashfs[0]: Bytes used: 7427584
flashfs[0]: Bytes available: 24957440
flashfs[0]: flashfs fsck took 20 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 50:57:a8:7b:56:c9
Ethernet speed is 100 Mb - FULL duplex
Loading "flash:/c1140-k9w8-mx.124-23c.JA7/c1140-k9w8-mx.124-23c.JA7"...#########
File "flash:/c1140-k9w8-mx.124-23c.JA7/c1140-k9w8-mx.124-23c.JA7" uncompressed a
nd installed, entry point: 0x4000
executing...
enet halted
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C1140 Software (C1140-K9W8-M), Version 12.4(23c)JA7, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 29-Jan-13 05:08 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
flashfs[1]: 27 files, 9 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 32126976
flashfs[1]: Bytes used: 7427584
flashfs[1]: Bytes available: 24699392
flashfs[1]: flashfs fsck took 5 seconds.
flashfs[1]: Initialization complete.
flashfs[2]: 0 files, 1 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 11999232
flashfs[2]: Bytes used: 1024
flashfs[2]: Bytes available: 11998208
flashfs[2]: flashfs fsck took 1 seconds.
flashfs[2]: Initialization complete....done Initializing flashfs.
Ethernet speed is 100 Mb - FULL duplex
Radio0 present 8363 8000 90020000 0 90030000 B
Radio1 present 8363 8000 98020000 0 98030000 0
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1142N-K-K9    (PowerPC405ex) processor (revision B0) with 98294K/32
768K bytes of memory.
Processor board ID FGL1611S3CW
PowerPC405ex CPU at 586Mhz, revision number 0x147E
Last reset from power-on
LWAPP image version 7.0.240.0
1 Gigabit Ethernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 50:57:A8:7B:56:C9
Part Number                          : 73-12836-04
PCA Assembly Number                  : 800-33767-04
PCA Revision Number                  : A0
PCB Serial Number                    : FOC16083D27
Top Assembly Part Number             : 800-33775-03
Top Assembly Serial Number           : FGL1611S3CW
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1142N-K-K9
% Please define a domain-name first.
Press RETURN to get started!
*Mar 1 00:00:0crypt on interface Dot11Radio 0 -Process= "Init", ipl= 0, pid= 3
*Mar 1 00:00:09.975: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self
test passed on interface Dot11Radio 1
*Mar 1 00:00:10.016: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log
(contains, 1017 messages)
*Mar 1 00:00:10.039: status of voice_diag_test from WLC is false
*Mar 1 00:00:11.080: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state
to up
*Mar 1 00:00:12.158: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 00:00:12.194: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1140 Software (C1140-K9W8-M), Version 12.4(23c)JA7, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 29-Jan-13 05:08 by prod_rel_team
*Mar 1 00:00:12.194: %SNMP-5-COLDSTART: SNMP agent on host AP5057.a87b.56c9 is
undergoing a cold start
*Mar 1 00:00:12.246: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:12.310: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to r
eset
*Mar 1 00:00:12.310: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to r
eset
*Mar 1 00:00:13.310: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
1, changed state to down
*Mar 1 00:00:13.310: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
0, changed state to down
*Mar 1 00:00:13.500: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:21.309: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne
d DHCP address 192.168.1.52, mask 255.255.255.0, hostname AP5057.a87b.56c9
*Mar 1 00:00:31.121: status of voice_diag_test from WLC is false
*Mar 1 00:00:31.181: Logging LWAPP message to 255.255.255.255.
*Mar 1 00:00:31.214: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power s
ource
*Mar 1 00:00:31.238: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:32.222: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
1, changed state to up
*Mar 1 00:00:32.222: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.
255 started - CLI initiated
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Aug 25 08:18:04.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 192.168.1.2 peer_port: 5246
*Aug 25 08:18:05.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
wmmAC status is FALSE
*Aug 25 08:18:06.031: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 192.168.1.2 peer_port: 5246
*Aug 25 08:18:06.031: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
*Aug 25 08:18:06.031: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Aug 25 08:18:06.167: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Aug 25 08:18:07.431: %CAPWAP-5-CHANGED: CAPWAP changed state to UP
*Aug 25 08:18:07.475: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller Cisco
_9a:8e:00
*Aug 25 08:18:07.518: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to a
dministratively down
*Aug 25 08:18:07.519: %LWAPP-3-CLIENTEVENTLOG: SSID test added to the slot[0]
*Aug 25 08:18:07.522: %LWAPP-3-CLIENTEVENTLOG: SSID test added to the slot[1]
*Aug 25 08:18:07.534: %WIDS-5-ENABLED: IDS Signature is loaded and enabled
*Aug 25 08:18:08.517: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
1, changed state to down
User Access Verification
Username: Cisco
Password:
AP5057.a87b.56c9>en
Password:
% Access denied
AP5057.a87b.56c9>en
Password:
AP5057.a87b.56c9#
AP5057.a87b.56c9#
AP5057.a87b.56c9#
AP5057.a87b.56c9#sh ip int brie
Interface                  IP-Address      OK? Method Status                Prot
ocol
Dot11Radio0                unassigned      NO unset reset                 down
Dot11Radio1                unassigned      NO unset administratively down down
GigabitEthernet0           192.168.1.52    YES DHCP   up                    up
AP5057.a87b.56c9#

Similar Messages

Golf Radio won't turn off after reinstalling CK-10...

For some time I've been using my CK-100 but without a switched 12v supply which means that the unit remained on after turning off the ignition but otherwise with no problems. I've recently bought a new loom and fed the switched 12v from the cig lighter so the CK-100 switches off/on and with the radio being fed from the big multipin plug rather than the speaker outlet with no problems but the radio often doesn't switch off when I remove the key. During normal operation there is no indication that there might be a loose connection and I have checked them all. The only thing I can think of is that I also updated the software to v4.5 so I'm wondering if that is causing any problems, does it think that there is a call outstanding although it doesn't mute the radio.
Any help appreciated
Phil

Sorry about the delay, Alan.
It's a possibility, although I'm used to seeing it more with older Symantec security suites rather than just the Antivirus. (For example, NIS 2005.)
The mechanism is two-part. The first part is that if there's an issue with iTunes rules in the firewall, sometimes the iTunes.exe process doesn't shut down after you "close" iTunes. Sometimes it can't even be ended in Task manager.
The second part is that security suites often try to have a component being the last item running in memory before the PC shuts down (because some malware attacks during the shut down procedure. Because the iTunes.exe can't be stopped, it tries to "outlast" that process ... and you get spectacularly slow shutdowns on the PC.
... So we'd better check to see if something like that is afoot ...
Restart the PC (power off?) And launch iTunes. Quit iTunes. Bring up your Task manager. Go to the processes tab. Click the "Image name" header to sort the processes alphabetically.
Is iTunes.exe still running even though iTunes has supposedly been shut down?

8560w Wireless Radio won't turn on after sleep mode

Anyone know the fix for the 8560w not turning on it's WiFi radio post sleep mode. It doesn't happen everytime, but most of the time. I will be at my workstation and when I close the lid, go to my meeting and turn it back on the wireless is off and I have to go to the "Windows Mobility Center" to turn it back on.
Any ideas or thoughts would be greatly appreciated.
Thanks!

Hi:
What model wireless adapter is in your notebook?
Maybe a driver update will help.
Paul

Help! Won't turn on, just happened over night.

My airport extreme has been working fine. Last night I used apple software update, only thing different then most nights. This morning I noticed the internet was down, went to the airport extreme and it won't turn on. No power, no light, no nothing. The surge protector it is plugged into has all the other attached gadgets working just fine.
Thanks for any suggestions on saving this.

It would be logical to check the power supply "brick" to see if it is delivering the 12 volts that it should be doing if it is working correctly. Radio Shack sells battery powered voltage testers for $10-12. Its a handy item to have around the house if you don't have one already.
If the power supply checks out OK, your best bet is going to take both the power supply and AirPort Extreme to an Apple store to let them have a look.

My Creative Zen4gb Won't turn on please help...............

Well I had my zen 4gb mp3 for about a year worked fine and everything until today I was listening to the radio and it just went off by it self, It was fully charged so the battery was not low. I try to reset it and it just show the label Creative sign then stood their then it turn off by it self, Now when I hook it up to my computer the black screen still won't turn on.
It will not come on for nothing.
I try to fill out the support thing but don't know the?
Product Serial Number:
Operating System:
What options do I have.
Thank you
Please contact me back.

Sorry for the late response I brought a charger ,It still wouldn't turn on for anything, The only thing that it did when I plugged in the charger adapter into the wall the light was blue for a few secs and that was it, It was charging for 7hours or more, I try to get the recovery thing on my computer but everytime I plug my mp3 to my computer its like it doesn't exist basically my player is not turning on for nothing.
Do you the Zen company could fix the is problem like a payment thing I'm really to pay for it.

Z22 won't turn on

Hi - my z22 won't turn on. Stays dark and dead even when connected to charger or usb-computer. I've been using it regularly with no problem. Any ideas? Thanks!
Post relates to: Palm Z22
This question was solved.
View Solution.

Are you sure that you charger is working? You can test this with a voltmeter (maybe you local Radio Shack could help you with this), or by trying it on another device that is working. Have you tried a reset on charge? If this does not work you can try a repeated reset process by pressing and releasing the reset button 10 times in a row as quickly as possible. Sometimes this will activate the device again. If none of these options works you should try a hard reset. A hard reset will delete all data on your device.
You may need to hard reset your device and rename your backup folder. Go to http://www.palm.com/cgi-bin/cso_kbURL.cgi?ID=887 and follow the directions to do a hard reset. Next before you hotsync your data back over you will need to rename your backup folder, to do that go here;
XP
C:\program files\palm or palm one\[hotsync username]\ and rename your backup
folder to backup.old
Vista
Start-->documents\Palm OS Desktop\[hotsync username]\ and rename your backup
folder to backup.old
Then hotsync to your current hotsync name and all your contacts, calendar,
tasks, and memos will come back over.
Show file extensions for XP or Vista
XP
If you can not view file extensions on your PC I would like you to open a
folder go to Tools-->Folder Options--> View (tab) and under show hidden
files and folders uncheck hide file extensions for known file types.
Vista
Open control Panel go to Folder Options--> View (tab) and under show hidden
files and folders uncheck hide file extensions for known file types.
KB Article link:
Click on the following link to the kb.palm.com webpage for the article regarding
http://www.palm.com/cgi-bin/cso_kbURL.cgi?ID=
Message Edited by Terabyte on 08-05-2009 10:37 AM

Power Mac G4 Gigabit won't turn on

My power mac g4 gigabit won't turn on. When you press the power button on the front it lights up for a seccond and then it turns off and the computer doesn't turn on. If you hold the power button down the light stays on but when you release it it turns off again. only the light on the zip drive comes on sometimes. I have tried to reset the PMU but that didn't do anything I took out the battery and replaced it but it didn't help.
PLEASE ANYBODY HELP ME!
Thanks,
rcrickarby

first of all, i'm an AMIGA guy. i did my share of apple ][ programming in the late 70's, but this is the first mac i've touched (literally) since 1985 when i played with the original mac. in 2000, i finally went from the amiga (i still have lots of 'em) to the Dark Side and got a PC (QUAKE II, DUDE!) running Windows NT, then Windows 2000, now XP. i finally retired that machine this year - i gave it to a neighbor for his kids.
now back to the topic...
i'm working on a friend's G4 gigabit machine which had a bad power supply (no 28V output). as a replacement supply is obscenely expensive and they apparently die early and often, i've got an ATX supply in there (let go my ears - i are an engineer and i know what i'm doing).
i'm currently feeding +5V standby from the ATX supply (+5 always hot, even when supply is "off") to the +28V trickle pin of the motherboard power connector. i'm not worried about firewire or ADC monitors at this point.
besides the power supply hack, i'm using a PC mouse & keyboard (USB) through a belkin flip KVM.
the machine works fine now, except:
1) if i let it put itself to sleep (power saver setting), it wakes up brain damaged. the screen is corrupt, the mouse pointer is present and moves, but it's for all intents and purposes dead and must be reset. if i put it to sleep with a quick push of the power switch (throbbing power light mode) and then wake it back up (after waiting seconds or hours), it's fine.
2) if i disconnect the AC (even briefly), it won't power back up until i reset the PMU. i bought a new battery at radio shack today (didn't realize they wanted ****$19.00**9.00** for the thing until i saw the numbers on the register!), and i'm giving it an overnight charge with everything powered up before seeing if that fixes things. interestingly, i came home with the new battery, and of course the machine wouldn't start as i had left it unplugged. popped the old battery out, put the new one in, and it started! of course, i excitedly shut it down and unplugged the AC for 5 minutes, but it wouldn't start until i did the PMU reset
i realize that either of these problems could be related to using only +5V standby for trickle power, but keep in mind that previous G4 machines (yikes/sawtooth) also used "standard" +5V trickle power, so i'm not breaking any new ground.
what else might be going on to prevent it from starting up when freshly plugged in?
i'm looking at two solutions for the 28V thing - one is an off-the-shelf DC to DC upconverter which turns 5V to 24V (and can even provide 2A if i diode-OR +5V standby with +12V), and the other is something i'll whip up myself using an LM3478 and a big FET which can provide 1A @ 28V from 5V. either of these should be enough to run powered firewire things, but again no ADC monitor.
system stats:
G4 gigabit, 400MHz, 1G RAM (512M PC133, 256M PC133, 256M PC100), 4.2.8f1 firmware, OS X 10.4.11
i saw a message in one of the system startup logs about the video card firmware being "too old". is there a way to update the firmware? here's what system profiler says about it:
ATY,Rage128Pro:
Chipset Model: ATY,Rage128Pro
Type: Display
Bus: AGP
Slot: SLOT-A
VRAM (Total): 16 MB
Vendor: ATI (0x1002)
Device ID: 0x5046
Revision ID: 0x0000
ROM Revision: 113-72701-125
one last thing - when the machine is asleep (throbbing power light), i assume the DRAM is on and being refreshed. how much current does that require at 28V?
i'm pleasantly surprised by how quickly it boots and shuts down. the "identify your keyboard" thing was weird, but effective. the UI is a little better than 1985, but still seems a little cryptic - and that's from a guy who still uses VI to edit software.
my only other apple experience since 1985 is an iPod Shuffle, which is cool once you get hold of a certain perl script to rebuild its database. until you do that, you're saddled with iTunes. i've only used (or tried to) the Windows version. i don't think i've ever used any software on any platform that was so LARGE, so SLOW, so INTRUSIVE to the rest of the system, and so COMPLETELY OPAQUE before (well, maybe ClearCase). dear apple - don't do THAT again.

E320 - wireless won't turn on after sleep

When i open lid after my laptop goes to sleep after i close it, wireless won't turn on (brand new laptop).
I fresh installed win7 x64 (with SP1 and all updates), all drivers and updates from lenovo page (power management, windows update "Enabling Wake on LAN from Standby for ENERGY STAR Version 4.0 for Windows 7", etc.....). I unchecked "allow the computer to turn off this device to save power" on wifi driver...
Bios is very small - didn't found stuff like "wake on lan", "flash over lan", etc.
In PROset/Wireless tool->Diagnose, it says Radio test-radio off....
Need little help
Solved!
Go to Solution.

denied wrote:
So, if anybody have similiar problem - try that
If you could mark the post you consider to have helped lead you to finding the solution as the solution this will help other members experiencing the same or similar hopefully find it quicker when using the forum search function.
[Click on Options, top right of the relevant post, and select Accept as Solution]
edit; for clarity
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

I was syncing my iPhone5 to iTunes and then my phone automatically locked and now it won't turn back on

I was syncing my phone to itunes and then my phone automatically locked and now it won't turn back on but when i plug it into a charger it makes the charging sound.

Hi lemmag17,
If your iPhone doesn't appear to be responding or turning on, you may find the following article helpful:
iOS: Not responding or does not turn on
http://support.apple.com/kb/ts3281
Regards,
- Brenden

K7N2 Delta ILSR won't turn off, just restarts

K7N2 Delta ILSR won't turn off, just restarts. Every time I click on "Turn off computer" in Windows XP, it shuts down, but restarts again. Could this be OS related, or perhaps Bios related. My other machine, almost identical to this one, except that the other machine has BIOS rev 7.6 and this one 7.2.

PSUs seem to be yr favorite subject, but I'm afraid this time it's software. I experimented some more as the problem only occured after installing the Nvidia drivers. Comparing the system settings in the device manager before installing drivers and after installing them, reveils that the problem shows up when AGP HOST TO PCI BRIDGE is installed. When killing this item the PC shuts off properly. Unfortunately when turning back on, Windows automatically reinstalls the PCI bridge and I have the problem again. LOOKS LIKE A MSI SOFTWARE PROBLEM !
By the way I have a PCI graphics board and not AGP in the failing PC (the good one has AGP graphics).
Now what?
R.

[Help]iPhone 5s screen won't turn on / won't play sounds

Hello, my name is Bryan.
I've got a problem with my iPhone 5s. I opened my iPhone to fix an issue with the home button (Watched a guide on youtube on how to achieve this), and I connected everything as it is supposed to go, my home button is working but now my screen won't turn on or the phone won't play any sounds. I know the phone it's on because I can connect it to the computer and the computer recognizes it. Also, I tried calling it, and it rings on the phone I am calling from, but my iPhone simply won't play any sounds...
I am also sure the phone is not in DFU mode.
Any help?
Thanks in advance,
- Bryan

It won't even vibrate or do anything, but it's on.

TS1741 Remote app on my iOS devices control my apple tv, but won't turn my newest gen apple tv on when i open the app.

Remote app on my iOS devices control my apple tv, but won't turn my newest gen apple tv on when i open the app. It used to turn my previous gen apple tv on. Remote app controls apple tv just fine once i turn it on with the provided remote control. Help?

Hello CournteyGould3,
Congratulations on your new Apple TV! I found an article with steps you can take when your remote app can't connect to the Apple TV. I recommend following the steps in the article below (you can skip any steps you have already taken):
Remote app for iPhone, iPad, or iPod touch can't connect to iTunes or Apple TV
http://support.apple.com/kb/TS1741
Thank you for using Apple Support Communities.
Best,
Sheila M.

My iPhone 5 won't turn on, the screen just stays black!

My iPhone 5 won't turn on I have held the power button to see if it's dead or not and it doesn't seem to change the screen it just black I thought the battery could of died or something similar it only happened about 2 hours ago please help!

Hey Thermali,
Thanks for the question, and great troubleshooting so far. To completely isolate the issue, you may want to follow these steps:
Will not turn on, will not turn on unless connected to power, or unexpected power off
- Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
- Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion.
Learn about LCIs and corrosion.
- Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
- After at least 15 minutes, if:
               - The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
               - The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
               - Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
- If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
               - If the display turns on, go to step 4.
               - If the display remains black, go to next step.
- Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to
restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
- If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
For additional information, see this article:
iPhone: Hardware troubleshooting
http://support.apple.com/kb/TS2802
Thanks,
Matt M.

My iPhone 5 won't turn on

My iPhone 5 won't turn on and won't restart or restore... any suggestions?

Is the Battery Charged...?
tammyschnitt wrote:
My iPhone 5 won't turn on and won't restart or restore...
See Here for > Frozen or unresponsive iPhone
Try this First... No Data will be Lost...
Press and Hold the Sleep/Wake Button and the Home Button at the Same Time...
Wait for the Apple logo to Appear...
Usually takes about 15 - 20 Seconds... ( But can take Longer...)
Release the Buttons...

My Iphone 5 won't TURN on or OFF it won't do anything it's just showing the Apple logo the WHOLE time Please help

MY IPhone 5 won't turn on or do ANYTHINGS please help

Plug into computer then hold the lock and home buttons until it syncs

1142N radios won't turn on

Similar Messages

Maybe you are looking for