11b client and 11g Access Point

Can 11g Access Point support 11b client ?
i have a Access Point AIR-AP1231G-E-K9.
Users with a 11g client adaptor is able to login successfully, but users with 11b client adaptor is not able to login.
How should i configure that AP so that 11b client can login as well ?
Should i downgrade my access point back to pure 11b ?

Hi
11b users should be able to log in, as this AP supports both 11b and 11g at the same time.
Please try this:
Under interface dot11Radio0, configure:
speed default.
This should set data rates to factory default settings allowing both 802.11b and 802.11g client devices to associate to the access points 802.11g radio.
HTH

Similar Messages

Dynamic VLAN Assignment with RADIUS Server and Aironet Access Points

Hi Guys,
I would like to go for "Dynamic VLAN Assignment with RADIUS Server and Aironet Access Points 1300". I want the AP to broadcast only 1 SSID. The client find the SSID ->put in his user credential->Raudius athentication->assign him to an specific vlan based on his groupship.
The problem here is that I don't have a AP controller but only configurable Aironet Access Points 1300. I can connect to the radius server, but I am not sure how to confirgure the AP's port, radio port, vlan and SSID.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml#switch
I go through some references:
3.5 RADIUS-Based VLAN Access Control
As discussed earlier, each SSID is mapped to a default VLAN-ID on the wired side. The IT administrator may wish to impose back end (such as RADIUS)-based VLAN access control using 802.1X or MAC address authentication mechanisms. For example, if the WLAN is set up such that all VLANs use 802.1X and similar encryption mechanisms for WLAN user access, then a user can "hop" from one VLAN to another by simply changing the SSID and successfully authenticating to the access point (using 802.1X). This may not be preferred if the WLAN user is confined to a particular VLAN.
There are two different ways to implement RADIUS-based VLAN access control features:
1. RADIUS-based SSID access control: Upon successful 802.1X or MAC address authentication, the RADIUS server passes back the allowed SSID list for the WLAN user to the access point or bridge. If the user used an SSID on the allowed SSID list, then the user is allowed to associate to the WLAN. Otherwise, the user is disassociated from the access point or bridge.
2. RADIUS-based VLAN assignment: Upon successful 802.1X or MAC address authentication, the RADIUS server assigns the user to a predetermined VLAN-ID on the wired side. The SSID used for WLAN access doesn't matter because the user is always assigned to this predetermined VLAN-ID.
extract from: Wireless Virtual LAN Deployment Guide
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00801444a1.html
==============================================================
Dynamic VLAN Assignment with RADIUS Server and Wireless LAN Controller Configuration Example
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml#switch
==============================================================
Controller: Wireless Domain Services Configuration
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801c951f.shtml
Any help on this issue is appreicated.
Thanks.

I'm not sure if the Autonomous APs have the option for AAA Override. On the WLC, I can go into the BSSID, Security, Advanced, and there's a checkbox that I would check to allow a Radius server to send back the VLAN.
I did a little research and it looks like the 1300 may give this option but instead is defined as "VLAN Override". I've found the release notes for 12.3(7)JA5 (not sure what version you're running) that give mention and a link to configuring EAP on page 4: http://www.ciscosystems.ch/en/US/docs/wireless/access_point/1300/release/notes/o37ja5rn.pdf
Hope this helps

Wlc 5508 and 40 access point 1141n disturbance in the temp response

Hello,
i have a wlc 5508 and 40 access point 1141n
there are 1500 users connected with this controller 5508.
but when i ping at my gateway ,there is a disturbance in the temp response .
Here below a snapshot:
Réponse de 172.16.1.1 : octets=32 temps=1 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=5 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=2 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=56 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=105 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=433 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=1 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=100 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=300 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=466 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=711 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=900 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=55 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=52 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=54 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=200 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=57 ms TTL=55
Réponse de 172.16.1.1: octets=32 temps=800 ms TTL=55
anyone help me?
thx

Looks to be wither a duplicate address issue or a configuration issue. Try to test with only using the 2.4ghz and then again with only the 5ghz and see if you see a difference.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

WRVS4400Nv2 router and WAP4410N access point

WRVS4400Nv2
Love it! More Bars In More Places! Yahoo and never cuts out...nice job guys worth the money!!!!
bugs
1. Can't find how to set it to use https for access of the admin panel, very puzzling
WAP4410N
bugs
1. WMACFilter.htm&unit=0&vap=0 > Wireless Client List
This needs a To Sort by Client Name, IP Address or MAC Address and it should always list
Select Check box || Client Name || IP Address || MAC Address
but it currently only lists ( this is bad form and looks rushed? )
Select Check box || MAC Address
AND No sort ability
This looks rushed because the partner device the WRVS4400Nv2 as the above functionality.
Doen't look good when the same functions don't work / look the same??
2. WMACFilter.htm&unit=0&vap=0 MAC 20:
If you enter a mac address into MAC 20: and save it it returns blank with the change saved to MAC 19 so it overwrites MAC Address 19 REAL BUG HERE!
A bug in common WAP4410N and WRVS4400Nv2
I will call this a functional bug
The connection control should have an input box with buttons for Add || Edit || Delete and you should enter the MAC Address in and click add and this should populate a read only textarea so you are NOT limited to just 20 client computers. Basically this should work like the Setup_lan.htm in WRVS4400Nv2 Static IP Mapping but instead of doing mapping just add/subtract/edit Mac addresses and you can fit a lot more than 20.
This is a Major limitation considering I paid pretty good money for this router and access point, I should have vertually limited clients
So back to the Setup_lan.htm in WRVS4400Nv2 static IP mapping......I LOVE this feature and the way it was implemented.....NICE JOB GUYS
Genius is not in the understanding of complexity but in its simplification! by R.Ries
Windows defined as 32 bit extensions and a graphical shell for a 16 bit patch to an 8 bit operating system originally coded for a 4 bit microprocessor, written by a 2 bit company that can't stand 1 bit of competition. by R.Ries
Ban Internet Explorer from your website and force upgrades to real browsers, FF, Opera or other

Hello
Genius is not in the understanding of complexity but in its simplification! by R.Ries
Windows defined as 32 bit extensions and a graphical shell for a 16 bit patch to an 8 bit operating system originally coded for a 4 bit microprocessor, written by a 2 bit company that can't stand 1 bit of competition. by R.Ries
Ban Internet Explorer from your website and force upgrades to real browsers, FF, Opera or other

Roaming between RV220W wireless router and WAP121 Access Point

Hello, I have recently purchased a RV220W wireless router and a WAP121 access point and i would like to allow my users to "roam" between the two networks as needed (so when the user is closer to whichever one they connect to that one since it has a better signal). For the most part I only have experience in cisco IOS and in actual routers not the wireless stuff so my knowledge has not exactly transfered over well.

William,
WDS will not work between the RV220W and WAP121 due to incompatible chipsets. The RV220W can be repeated using WDS by another RV220W or RV180W only. You will need to plug the WAP121 into the RV220W or try WorkGroup Bridge mode to repeat the signal.
Regarding roaming, the router or AP are not aware of each other and do not have the capability to disconnect a client and help them connect to the AP with the stronger signal. The client will switch to the stronger AP only when the original signal is lost.
The Aironet (enterprise) devices have the ability to utilize a wireless LAN controller which can help keep devices connected to the stronger signal and allow truly seamless roaming between APs.
- Marty

N95 Wifi, home network and hidden access points

Hello-
Just picked up a N95 and having some problems. First, my home network doesn't broadcast a SSID. I stumbled across the home network option and was able to configure it. However, it's never an option when I need an internet connection; e.g., it never shows up in the wlan list.
So, how do I congigure a hidden access point so I can use it? The user guide says you should be able to do it manually, but doesn't go into any details.
Secondly, exactly what is the home network setting for and why is it separate from the other wlan settings?
Thanks,
Jay

Jay,
I too have a hidden network (SSID not broadcast), the N95 seems to have a problem with this. It may or may not show up on the active standby screen (on my Voda N95, it shows up when I take my sim out!).
To configure your accesss point :-
Tools / Settings / Connection / Access Points
then Options / New access point
Connection name
(enter a name, whatever you want to call it)
Data bearer
=wireless LAN
WLAN network name
(enter your SSID here)
Network Status
(public or hidden)
WLAN network mode
(Infrastructure or ad-hoc. If you're using a router, infracstructure should be the one you want)
WLAN security mode
(Open, WEP, 802.1x or WPA2. Check your router)
WLAN security settings
WPA/WPA2
EAP or Pre-shared key (consult your router)
EAP plug-in settings or Pre-shared key
(which one you get depends on what you set above)
WPA2 only mode
(leave alone)
Having done all this it still won't show on the active-standy screen (at least it doesn't on mine) in the WLAN section BUT if you know try and surf the web it should ask which access point you want to use - assuming you've got it set to 'always ask'. What this seems to do is only list the connections that it can find (i.e if you've got a 'Starbucks' and a 'home' connection defined, it'll only show 'home' at home and 'Starbucks' when you're getting your latte. The standby screen may show, how to decribe it, a four leaf clover near to the battery level indicator, this is the indication that it's either found or connected to your wireless lan.
I think the 'Home netw.' option is for use with the Home Media Server application supplied on the CD. I haven't tried it so can't confirm for sure.
Hope this helps,
Simon
E&OE
Sony CMD-Z1, Nokia 8110, Nokia 6210, Nokia 6610 (returned within a week), Nokia 6600 (twice), N95, 3109c & N97.

Problems with AirPort and WPA access point

Okay, I have done quite a bit of research and I still cannot resolve my problem because of this, I am turning to this user community.
Here is what I know as of right now:
I am running Windows OS X 10.4.4 with AirPort Update 2005-001. My Access Point is a 3COM 8250.
The AP is setup not to broadcast its SSID, to use WPA-TKIP (or in Apple terminology, WPA Personal) and the password is set to use alphanumeric.
When I try to connect my PowerBook with the SSID name, WPA Personal and the correct password, I get the following error:
The password you entered is not correct for the Airport network *******.
To troubleshoot here are the test I have run and their outcomes:
Test
- Result
Set the AP to completely open
- Connected
Set the AP to open, didn't broadcast the SSID
- Connected
Set the AP to WEP, broadcast the SSID
- Connected
Set the AP to WEP, didn't broadcast the SSID
- Connected
Set the AP to WPA & WEP, broadcast the SSID
- WEP : Connected
- WPA : Not Connected
Set the AP to WPA & WEP, didn't broadcast SSID
- WEP:Connected
- WPA:Not Connected
Set the AP to WPA only
- Not Connected.
Now, I should mention that when I was running 10.3.3 I could not connect either. The AP is running the newest firmware and I have three Windows XP SP2 laptops / workstations that can connect with no problems.
I have tried to find a compatibility matrix on both 3COM's and Apple's websites to see if it might be a compatibility issue but I have not been able to find one on either site.
Any help that anyone could provide would be greatly appreciate.
Thanks in advance.
17" PowerBook G4 Mac OS X (10.4.4)

Hello MisssAsh. Welcome to the Apple Discussions!
It's always a good idea to do a complete power recycle when changing network configurations.
Try the following, in order, checking for Internet access after each step, until resolved:
1. If the modem has a reset switch, use it to reset the modem. Wait at least 5-10 minutes for the modem to initialize.
2. Remove power from the modem. If it has a backup battery, remove this as well. Wait 5-10 minutes. Replace the battery, and add power back to the modem.
3. Perform a complete power recycle of your network components as follows:
Modem/Router Power Recycling - Quick
o Power-off the modem, AirPort Express Base Station (AX), & computer(s); Wait at least 5 minutes.
o Power-on the modem; Wait at least 5 minutes.
o Power-on the AX; Wait at least 5 minutes.
o Power-on the computer(s)
If this fails to get the modem to "recognize" the Internet router, then try the "Full" version.
Modem/Router Power ReCycling - Full
o Power-off the modem, AX, & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
o Power-on the modem; Wait at least 15 minutes.
o Power-on the AX; Wait at least 5 minutes.
o Power-on the computer(s)
4. Contact your ISP to have them perform a "modem reset."

Radius local server and wireless access points

Hello to all,
I would like to ask a question related to radius server. I have a Allied telesis core switch and i configure the radius server locally, also i configure the port1.0.7 for dot1x and i am using dynamic vlan. If i connect my laptop to port 1.0.7 i can get the correct ip from the dhcp server. If i connect an access point to the same port , how i should configure the dot1x ? for multiple hosts? I know i am using allied telessis but the config is very similar to the cisco: take a look:
(Radius and nas config)
radius-server host 127.0.0.1 key awplus-local-radius-server
aaa authentication dot1x default group radius
aaa authentication auth-web default group radius
crypto pki trustpoint local
crypto pki enroll local
radius-server local
server enable
nas 127.0.0.1 key awplus-local-radius-server
group Andrew
attribute NAS-Identifier andrew
attribute Tunnel-Medium-Type IEEE-802
attribute Tunnel-Private-Group-Id 10
attribute Tunnel-Type VLAN
user andrew encrypted password wh8q0J2oYSn0y4cynksNCqfbaUtRGv/E6JaJrW+s3Zs= group Andrew
(port config)
interface port1.0.7
switchport
switchport mode access
auth-web enable
dot1x port-control auto
auth host-mode multi-supplicant
auth dynamic-vlan-creation
I tried with auth-web and without but no luck. If someone have a sample config how to configure the dot1x to be able to use access point please paste it.
Thanks
Andrew

I'm not sure if the Autonomous APs have the option for AAA Override. On the WLC, I can go into the BSSID, Security, Advanced, and there's a checkbox that I would check to allow a Radius server to send back the VLAN.
I did a little research and it looks like the 1300 may give this option but instead is defined as "VLAN Override". I've found the release notes for 12.3(7)JA5 (not sure what version you're running) that give mention and a link to configuring EAP on page 4: http://www.ciscosystems.ch/en/US/docs/wireless/access_point/1300/release/notes/o37ja5rn.pdf
Hope this helps

E60 SIP and several access points

I have e60 and use it to make VoIP calls within our corporate network. We have several access points in the office (office is big and one point is not enough to cover it.) Thus, I have two SIP profiles in the phone for two different access points with "always on" option. Everything works fine until I start walking between those points and phone loses connection to one point and establishes connection to the other. Often, when I return to the area of the first point, the phone gets frozen and dialpad is not working. However, menu button is still working and navigation is possible. The only way to get phone working normally again is to reboot it.
Has anyone faced that problem? Any suggestions to solve it? I have FW 2.0618.06.05 RM-49 which seems to be the latest one.
Thnx!
Valery

23-Aug-2006
12:45 AM
iphone wrote:
My problem is resolved but thats not mean to Nokia team don't do their job and make new SIP protocol for all Eseries phones.
Everybody who wants working SIP on their Nokias, check this: http://www.control.aau.dk/~danji/how-tos/nokia_e60_pabx.php but remember when you type "Proxy server address" and "Registrar Server Address" not put sip:s1.easypabx.com that! You have to write IP address - this one: 194.192.14.200! REMEMBER IT!Message Edited by iphone on 23-Aug-2006
12:48 AM
this helps no one apart from you.
Can you keep this on topic? the whole thread is confusing.

Westell 327w and Wireless Access Point

I had DSL last year, but have since changed to FIOS, which I love. So I have the Westell 327W modem/router that isn't being used. I have decided to use it in another project for the 4 port ethernet and the wireless capability.
As this other project, we are using another service, which isn't DSL. However, I figured that I could use the 327w as the wireless access point. I currently have access to the internet through the provided internet service and from there I go into a Cisco ASA 5505 firewall. From there I run an ethernet cable to the 327w.
As long as I plug a computer into one of the 4 ethernet ports on the 327w, I'm able to ping to the Internet using either the IP address or using DNS. I'm able to surf and everything.
I have also set up the wireless and using WPA security and I'm able to connect a laptop to the wireless. I get the IP address via DHCP from the ASA, so I have turned off the DHCP server on the 327. I have also turned off the firewall. I then test connectivity and I can ping anything on the network that is assigned by the ASA, but when I try to ping to an Internet address, by the address, I get request timed out. I also don't get anything back on DNS and so forth.
What do I need to do on the 327 to allow the wireless to work with the current connection set up.
Thanks for the help and information.

I got it to work. What I had to do was to set up the 327w in VLAN mode so that the wireless side would send the packets out the ethernet port to the ASA or another router.
In fact, I'm writing this on the wireless setting of the 327w. So setting the VLAN allow the wireless to send and receive packets.

Help required to implement Cisco 2504 WLC and 1042 Access Points

Hi,
My name is Vidya Sagar. I am new to Wireless technology. We are planning to implement Wireless in our office. I have given the requirements below. Kindly go through the details and let me know how to start.
We have purchased Cisco 2504 Wireless Controller (One) and Ciscon 1042 Access Points (Five). At present I am going to use 3 access points only.
I have attached a simple diagram of our office network. We have more than 30 VLANs configured in Core Switch, we are planning to give wifi access to only 3 VLANs.
1. VLAN 121 ( IP Segment - 10.52.121.0 /24)
2. VLAN 116 ( IP Segment - 10.52.116.0 /24)
3. VLAN 100 ( IP Segment - 192.168.100.0 /24) (Guest)
Please give me a implementation plan to do this. I would like to use LDAP or ACS for authentication purpose.
Regards,
Vidya Sagar

Lets just do this simple first before you start using ACS as that will require a certificate installed on the ACS for using PEAP.
So first off, the WLC we will say is in vlan 10. When you are going through the startup wizard, make sure you define the vlan tag to 10 on the management interface. Make sure your virtual interface is an IP address that is not routed in your network, like an out of band IP.
Make sure the WLC time is correct or use NTP!!!!
Now you should be able to http or https to the WLC. I would upgrade the code to v7.4 and install the FUS image. Please reference this link for the upgrade procedure. You don't have to upgrade now... I would wait till you get everything working first.
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn74.html
Now I would connect the APs on the same vlan as the WLC for now. Make sure there is dhcp on that subnet. Once the APs have joined, then you can move them to any subnet you want. Since you don't have many APs it would be okay to leave them in the same vlan as the WLC management or out them on any other vlan you choose. The APs will be connected to an access port NOT a trunk port!!!!
The WLC will need to be connected on a dot1q trunk port only allowing vlans 10,100,116,121. The 2504 running v7.4 will support LAG (etherchannel). Any ways, your switch port should look like this for example only
Interface gigabit1/0/1
description WLC2504
switch port trunk encapsulation dot1q
switchoort mode trunk
switch trunk allowed vlans 10,100,116,121
spanning-tree portfast trunk
channel-mode group 10 mode on << only for v7.4 if you use lag
Don't connect all four ports right now, just port one!!!!
Your Guest vlan, you will need to create an ACL to block traffic from accessing the internal network. You might want to allow dhcp and DNS bit I would leave it open first until you can verify everything is working.
Now on the WLC you need to create a dynamic interface for vlan 100, 116, and 121. If you click on the Controller tab in the GUI and click on interfaces on the left hand side, that will take you to where you can add/delete/modify your interfaces. When creating these interfaces, make sure you add the dhcp server IP address for the primary and or backup.
Now that you have your dynamic interfaces created, its time I create your SSID. Now click on the WLAN tab on the GUI and click on WLAN and then on the too right select Create New and then click go. Select WLAN on the drop down menu and then for the profile name I would use the SSID name also for simplicity.lean e the WLAN id to 1 for this and 2 for the next and so on. After defining these and clicking Apply you can now define your SSID. On the General tab, enable the status and leave the radio policy to all for now, you can decide later what you want to use. Choose your interface you wan to place this SSID on and enable Broadcast SSID for now and leave everything else alone. Now click on the Security tab and on the layer 2 Security, leave it at WPA + WPA2, only check WPA2 Policy and for WPA2 encryption choose AES only. Now go to the bottom of that screen and choose PSk. We will do pre shared key for now so you get to understand the setup and make sure everything is working first. Now on the PSK format, choose ASCII and put your pre shared key in the input box. Make this simple to for testing. You don't want to put in symbols or anything like that. When you are don with that, check apply on the top right and test.
Now you can repeat this with your other SSIDs just to test. Your guest network you can leave open for now to test open authentication.
Here are some links for the WebAuth feature:
https://supportforums.cisco.com/docs/DOC-13954
http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a0080b1a506.shtml
Now if you want to use ACS with PEAP, here is some links for that:
https://supportforums.cisco.com/videos/2499
http://www.cisco.com/en/US/products/ps10315/products_configuration_example09186a0080bd1100.shtml
https://www.google.com/url?sa=t&source=web&cd=8&ved=0CFQQtwIwBw&url=http%3A%2F%2Fwww.youtube.com%2Fwatch%3Fv%3DWk_bRdmsQlA&ei=_BEyUeCYM8TdqAHHsICAAw&usg=AFQjCNF8PiVBQK1Kipb4j8AzD153bKtmgA&sig2=smHhNVmCr2of2NzbnDhGmw
Well that is it, hopefully you can get the wireless up for testing and verifying everything works!
Sent from Cisco Technical Support iPhone App

Security questions, cloud, and multiple access points

itunes:
i can't buy anything becasue fo the ******* security questions. thoughts?
also, can i download from itunes on my air, then, access the songs on both my mbpro and also, iphone4?
why am i having to ask? siri needs to know.

There is no way to tell your MacBook which access point to use. Since they all have the same SSID, they are seen as the same seamless network.

SG300-28P and aironet access points

Dear support,
does Cisco SG300-28P provide enough PoE to power access points 1550 and 1600?
Thank you

Hi Mireille, it should. The 1550 is 802.3af compliant.
The 1600 may be interesting because it can actually draw up to 15.4 watt of power and you may run into limitations of cable. It is also 802.3af compliant.
-Tom
Please mark answered for helpful posts

PoE for Cisco 1242AG and 1310G Access Points

Dear All,
we purchased a Cisco 1242AG and a 1310G Access Point and in the DataSheet it was specified that these APs support Power-over-Ethernet. The problem is we don't see any RJ-45 port in either AP which could be used for connecting the AP to an PoE Switch. Can you please tell us how we can connect these APs to an 802.11af compatible PowerBridge (by Intermec) ? Thanks.

Hi Thorsten,
The 1242 should be good to go but the 1310 is powered quite differently. Have a look;
AP 1240 Series - Hardware (see diagram)
http://www.cisco.com/en/US/products/ps6521/products_installation_guide_chapter09186a008079b7f4.html#wp1071972
Connecting the Ethernet and Power Cables
http://www.cisco.com/en/US/products/ps6521/products_installation_guide_chapter09186a008079b7f4.html#wp1052781
1300 Series Power
Power
The access point/bridge receives inline power from the Cisco Aironet Power Injector (hereafter called the power injector). Dual-coax cables are used to provide Ethernet data and power from the power injector to the access point/bridge. The power injector is an external unit designed for operation in a sheltered environment, such as inside a building or vehicle. The power injector also functions as an Ethernet repeater by connecting to a Category 5 LAN backbone and using the dual-coax cable interface to the access point/bridge.
The power injector is available in two models:
Cisco Aironet Power Injector LR2 standard version (included with the access point/bridge)
48-VDC input power
Uses the 48-VDC power module (included with the access point/bridge)
Cisco Aironet Power Injector LR2T optional transportation version
12- to 40-VDC input power
Note The power injector and the power module must not be placed in an outdoor unprotected environment. The power module must not be placed in a building's environmental air space, such as above a suspended ceiling.
http://www.cisco.com/en/US/products/ps5861/products_installation_guide_chapter09186a008079b93b.html#wp1051840
Dual coaxial cable to run from the power injector to the 1300. See attached notes:
Cisco Aironet 1300 Series
Cisco Aironet 1300 Series Access Point/Bridge Power Injector
The Cisco Aironet 1300 Series Outdoor Access Point/Bridge Power Injector,converts the standard 10/100 BaseT Ethernet interface that is suitable for weather protected areas to a dual F-Type connector interface for coax cables that are more suitable for harsh outdoor environments. The Power Injector also provides power to the outdoor unit over the same cables with a power discover feature and surge protection. To support longer cable runs from your wireless network switch or router, the Power Injector LR is designed to accommodate up to a 100 meter coaxial cable run plus 100 meters of indoor cat5 cable?enabling total cable runs up to 200 meters. The Cisco Aironet 1300 Series Outdoor Access Point/Bridge ships with the Power Injector LR2 and an AC power supply.
From this link:
http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a008022551d.html
Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide
Ethernet Ports
The access point/bridge dual-coax Ethernet ports consists of a pair of 75-ohm F-type connectors, linking the unit to your 100BASE-T Ethernet LAN through the power injector. The dual-coax cables are used to send and receive Ethernet data and to supply inline 48-VDC power from the power injector to the access point/bridge.
From this link:
http://www.cisco.com/en/US/products/ps5861/products_installation_guide_book09186a00804d3095.html
AIR-PWRINJ-BLR2
F-Type Connectors
Dual coaxial cable carries full-duplex Ethernet, DC power, and full-duplex console port (RS-232 connection)
From this link:
http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a00802252e1.html
Hope this helps!
Rob

Problem with PowerBook (but NOT MacBook) and two access points on network

I recently installed a wall-plugged ethernet adapter system (Netgear XE104 and XE103) and plugged a wireless access point (Netgear WPN802) into one of the adapters (in the part of our house where we lacked a wireless signal) in order to extend the range of our (DSL) wireless network. I configured this new access point--disabled DHCP, assigned an IP address to the access point that does not fall into the wireless router's IP adress range, put the wireless router and access point on different channels (6 and 11), and made sure the router and access point had the same SSID.
I have had no problems using the resulting setup with our new MacBook--everything goes as planned. BUT I am having a terrible time with my PowerBook G4. It has a really strong signal everywhere, but when I open my browser it says that I am not connected to the internet. The problem seems to be that my PowerBook refuses to change channels once it connects to one. I installed iStumbler to see if I could manually control which access point/channel the PowerBook uses, and, while I can track the signal strengths for both access points, I can't get my PowerBook to switch from one access point to the other.
I've tried just about everything I can think of. I suppose I could try giving a different SSID to the access point (and then try to switch with the airport menu in the toolbar), but I would like to avoid this if possible.
I would really appreciate any advice you have. Thank you!

Can you connect if you temporarily turn off WEP or WPA?
This will determine if it is a WEP or WPA issue.
Does your PC support WPA, from both a hardware and a software perspective?
The problem you are having probably lies with the encryption key.
Accessing a Airport Network with a Windows XP PC or laptop (with XP SP2)
http://tech.ifelix.net/1011.html
Accessing a Airport Network with a Windows XP PC or laptop (with XP SP1)
http://tech.ifelix.net/1010.html
Problems connecting an XP PC to an Airport Base Station
http://tech.ifelix.net/2002.html
iFelix

11b client and 11g Access Point

Similar Messages

Maybe you are looking for