11g Grid Control with Dataguard

Hi ,
I need to configure a 11g Grid Control with Dataguard for the repository, are there any documents that i can follow for configuring the dataguard
for the Grid Control 11g, I am interested as how i would be setting up the tns entry in the OMS , since i had to do the failover / switchover etc of OEM Grid Control application across the standby .
Kind regards
Krish

Hi,
Please follow the document provided below:
How to Configure the OMS Connect String when Repository is in a Dataguard setup (Doc ID 1328768.1)
Let me know, if you are looking for the same document.
Best Regards,
Venkat

Similar Messages

Suggested concept for Grid Control with DataGuard solution

Hello,
I want a Disaster Recovery solution for OEM Grid Control with DataGuard but with only one OMS running. (11.1)
I have figured out the following.
Installation OEM Grid control om host A. Repository is created on Host A. Connection to database is done thru servicename DBGRDSRV on Host A
Installation OEM Grid control om host B. Repository is created on Host B. Connection to database is done thru servicename DBGRDSRV on Host B
I stop OMS on host B and I drop the database on Host B
Then....
I create a Dataguard configuration for DBGRDSRV, the prim database run on Host A en secondary on Host B
In case of a failure i switch the database. On host B i will have DBGRDSRV as the primary database
I start OMS on host B and the agent.
In case the failure is resolved i switch back eveything
Will thos concept work?
Do i get some troubles with the emkey, and if so, does anybody has a solution for this?
Any help is appreciated
Regards,
Jaap
Edited by: user9956284 on 28-jul-2011 10:44

Hi,
Please follow the document provided below:
How to Configure the OMS Connect String when Repository is in a Dataguard setup (Doc ID 1328768.1)
Let me know, if you are looking for the same document.
Best Regards,
Venkat

Download problem with EM 11g Grid Control Release 1 (11.1.0.1.0)

Hi all,
I have problem with Enterprise Manager 11g Grid Control Release 1 (11.1.0.1.0) for Linux x86-64 (64-bit) downloaded archives.
Actually with GridControl_11.1.0.1.0_Linux_x86-64_2of3.zip (1,589,671,704 bytes) (cksum - 535544209)
I successfully downloaded all archives but cksum for this file (...2of3...) is invalid.
Even it is invalid I tried to install. Installation starts ok, but it breaks after few moments.
Regards

Here is cksum from file that I downloaded 3966614633 and on download page is 535544209.
It's obvious that something is wrong!
Oracle personal should fix this issue.
Anyhow, there is another way... Download from different location. See this thread:
Re: Invalid Software Download from OTN for Grid Control 11g on Linux x86_64
Regards

11g Grid Control - Host Configuration Collection Problems

Hi Guys,
I just installed Oracle 11g Grid Control and it has been running for 2 weeks until I recently tried to walk through the parts of it.
My intention was to clear off all the error messages, critical warnings, alerts, and policy warnings.
When I arrived at the development summary box, on the home tab, I can see that there is 1 collection problem.
When I clicked it, I saw that apparently the problem is with the host where I installed the grid control.
Problem type: Warning during collection of Oracle Software
message: Unknown WLS Home Location or WLS Version in Middleware Home /u01/app/oracle/product/middleware
I tried clicking on the "Refresh Host" button, but it didn't solve the problem at all.
I have also tried to take a look at the targets.xml however it seems the configuration in there are already pointing to the correct path to the weblogic home.
Please let me know if anyone has a suggestion for this.
Searching from google doesn't really return anything closely matched to this.
Thanks,
Adhika

What is the intent/timeline for fixing this bug? On MOS, it appears to have a status of "Status 33 - Suspended, Req'd Info not Avail". We are encountering this bug also and I would glady provide information from our systems in order for the issue to be resolved.
Thanks.
PostScript: FWIW, Google yielded a blog referencing this error and Doc ID 1433113.1. I am unable to access that document (as was the blogger). Because of this, and another major caveat (our machines with this collection error do not have WLS installed on them), I'm thinking this probably needs to be an SR rather than a forum discussion.
Edited by: JeriF on Feb 4, 2013 12:00 PM

OEM 11g grid control - Question

Dear DBA's,
I'm using 11g grid control, RDBMS - 11.2.0.2 on RHEL 5.0
My current setup : I have 4 node RAC database running on (node1, node2, node3, node4). My RMAN backup job in EM runs from node1.
Preferred setup : I need to modify this job or create a new one (whichever is feasible) so that my backup job runs from (node3 or node4) instead of node1.
Can you kindly suggest How can I modify the setup to meet my requirement?
Thanks

I made these changes in the RMAN script (In OEM JOB Parameters) and still see backup running from node1.
I have recreated jobs (Changed ownership of these jobs from SYMAN to a different ID, which was also part of my task) and during Job creation, while adding targets (I chose target type as Database instance of node4 instead of Cluster database) This fulfilled my request. Thanks again for your reply.

Oracle 11g grid control software for Oracle Enterprise Linux 5.0 version

Hi,
Just curious to know when Oracle 11g grid control software for Oracle Enterprise Linux 5.0 version will be released. If already released, can you post the link?
Regards,
Manohar

aadragna wrote:
What is the best installlation document to follow for the latest EM Grid control ?The latest Grid Control is available for download at http://download.oracle.com (Scroll down to "Enterprise Management"). There is a README beside the download link. THAT README PROVIDES INSTALL INSTRUCTIONS.
In a nutshell, you install the lowest version (10.2.0.1 or 10.2.0.2, which ever is lower for your Grid Control platform), and then apply the 10.2.0.5 patch according to the readme. That should not normally take more than a day.
>
Also, can GRID discover PeopleSoft and Siebel application software ?
That can be found using the self-help portal: http://otn.oracle.com -> Products : Enterprise Management (left edge menu). In the 'Product Focus' area, you will notice 'Application Management' which will lead you to the appropriate data sheets and supporting information.

Disk 1 of Enterprise Manager 11g Grid Control not downloading correctly

Hello, I'm downloading Enterprise Manager 11g Grid Control.
The first disk, of three, does not download correctly:
GridControl_11.1.0.1.0_Linux_1of3.zip
On the web page, its size is listed to be around 1.3 GB.
However, when downloading, it thinks its actual file size is only around 643 MB.
So only that much gets downloaded.
But after downloading, this .zip file cannot be opened, it does not appear to a valid .zip file.
Please investigate and fix this.
Thanks
Eugene

Please check from edelivery.oracle.com . You need to unzip all the zips under one dir.

Weblogic license required for 11g Grid Control?

Weblogic is a pre-requisite for installing 11g Grid Control.
if you do not have weblogic already, and your only requirement for it is to use for Grid Control, is a license for Weblogic required?
I have raised an SR on this - and have been told a license is required.
I'm staggered by this - the packs in Grid have always been licensable, but the very basic functionality has always been free - including the use of an 'infrastructure' database to house the repository.
I'm interested to hear other peoples' experiences and whether this is a 'known' fact.

I've already asked Oracle sales staff about it, but I don't want to mislead you.
Could you remind them their restricted-use license?
Grid Control includes a restricted-use license for the Oracle Database and Oracle Application Server components required to deploy Grid Control. Refer to Section 1.3.3,
"Restricted-Use Licensing," for details on the restricted-use licenses
This is the URL of the document: http://download.oracle.com/docs/cd/E14571_01/doc.1111/e14860.pdf
I would be happy to hear from their answer.
Regards
Gokhan

How to add new host to 11g grid control

I have install silently oem agent 11g in a solaris system. The installation was successful and agent is up and running.
But the thing is I can't add this client and its database in my OEM Grid Control interface. When I try to add the target it shows the bellow error
Information
You cannot add a host target from Enterprise Manager Grid Control.
To add a host target, install the Oracle Management Agent on the host computer you want to manage. When the Management Agent begins communicating with the Oracle Management Service, the Management Agent target and the Host target will appear in the list of targets.
My Question is how i can the target's agent can communicate with OMS agent? and How this target can be incorporated?

Hi,
the host and agent targets should show up right after installation of the agent, if securing was successful. I assume the error happened somewhere there.
Can you please paste the output of following command:
$ORACLE_HOME/bin/emctl status agent
where ORACLE_HOME is set to your newly installed agent?
Also, please check if you see any errors in $ORACLE_HOME/sysman/log/emagent.log and emagent.trc about communication between the agent and your OMS.
Best regards,
Robert

OEM 11g Grid Control installation for 10g R2 database

Hi ,
I am new with oracle enterprise manager grid control ,
I have 3 questions ,
1. My customer is using windows server 2008 with oracle 10g R2 database , can I install OEM 11g R2 to monitor all the 10g databases ?
2. I found only 32 bit installers for windows , where as they are using 64 bit OS , is it fine to install 32 bit OEM in a 64 bit OS ?
3. Do they require any separate license for OEM 11g , they have license for oracle 10g database ?
I will really appreciate if someone can help me with these details , thank you.

1. My customer is using windows server 2008 with oracle 10g R2 database , can I install OEM 11g R2 to monitor all the 10g databases ?
Yes
2. I found only 32 bit installers for windows , where as they are using 64 bit OS , is it fine to install 32 bit OEM in a 64 bit OS ?
Yes
3. Do they require any separate license for OEM 11g , they have license for oracle 10g database ?
You don't need any license to use OEM 11g, however you do need licenses to use Management Packs
Checkout:
Oracle® Enterprise Manager Licensing Information
11g Release 1 (11.1)
http://download.oracle.com/docs/cd/E11857_01/license.111/e11987/toc.htm
Regards
Rob
http://oemgc.wordpress.com

10gR2 Grid Control with previous Agents?

I have 10gR2 Grid Control installed on a Linux Server. I want to use it to create a DataGuard standby database. The issue is that the primary database is 10gR2 on a HP-UX server using ASM and the standby database will also be 10gR2 on a HP-UX server using ASM. Will the 10gR2 Linux Grid Control be able to handle this since the agent on the primary will be 10.1.0.4? Note: 10gR2 is available for HP-UX but 10gR2 Grid Control is not yet available so that is why I have 10.1.0.4 agent.

Yes , it is able to handle

11g Grid Control in a cluster?

Hi All,
I am trying to find some official doc on how to setup an MAA architecture for 11g GC.
I have already done the following:
- installed 11.2.0.1 RAC database
- installed wls 10.3.2 on both nodes
- installed OMS on one node
- added the second OMS instance on the second node
Now, in WLS console I can see that there are 3 servers created (1 Admin + 2 OMS servers).
However, there is no cluster setup in WLS.
I am also planning to use a load balancer before the OMS instances.
Are there some notes on how to set this up? All I could find was stuff about 10g which is still based on iAS so that's not any use.
Also, where can I find notes about how to setup load-balancer for an 11g OMS clustered?
Regards,
Pawel.

Thanks !
However, I have a problem on deciding how to create the shared filesystem for the loader... In your example there is the following statement:
■The second thing to consider is shared storage, for both the XML file loading, and the software library (used for patching and provisioning). So make sure you can add a good shared storage solution to the OMS machines when needed to handle the shared files
What is the best way to do that?
- OCFS2
- GFS
- NFS (I don't like this solution as it is not HA - if primary server goes down - so does the shared folder in all attached nodes)
- ASMCF (installing a whole Grid Infrastructure with ASM sounds way too much overhead to accomplish a simple task of sharing a directory between to nodes)
Currently we have FC interfaces installed on both machines and attached to a disk storage matrix. In other words we have the same device /dev/raw1 visible from both OMS nodes.
Which approach is best keeping in mind we want High Availability maintaned?

Grid control with combo cell

Does Anybody have some information about grid
control/oracleSpreadTable with combo list instead of text cell.
Please help!!
null

As curious as I always am, I was able to discover my XE database from the GC 10.1.0.4 last month. I did this because I asked myself the same question. When there is time, I normally will try everything that says "Not supported" or "Not compartible" to prove it right or wrong. So give it a go, but don't post errors from it here :-). I have not tried it for GC 10.2.0.2, but it worked on 10.1.0.4 (hopefully 10.1.0.3).
Remember, XE has all the features of EE, but a cutdown version. It has an Oracle Service and a Listener on a port, so the agent will pick them up. I have tried all possible things and tools (Forms, Reports, Designer Repository, Jdeveloper, SQL Developer, ODBC, JDBC etc) on XE to break it, but it works like EE. The only difference is when you hit the max allowed 4GB (excluding 1GB system) and I proved the limit right by kicking of a data load into a table using a cursor until it hit the maximum 4GB limit error.

Oracle 11g Grid Control failure at database credentials

Hi ,
I have the environment like Windows 2008 64bit machine. I have installed oracle database in one machine and in second machine , installed weblogic server then trying to install Grid control but
I'm facing the issue when i give the database credentials , its throwing message like check that listener is up and running or not.
I have checked everything is working.
Error is : There was a problem connecting to the database on the host and port specified. Check to make sure the host is up or that the database listener is running on that host
i have verified in the forums . but nothing worked for me. Could any one please help me out

If you have not tested a sqlplus connection to the database as user sys from the host where you want to install Grid Control, then try it.
Ex:
sqlplus sys/<PASSWORD>@"(DESCRIPTION=(ADDRESS_LIST=(ADDRESS=(PROTOCOL=TCP)(HOST=<HOSTNAME>)(PORT=<PORT#>)))(CONNECT_DATA=(SID=<SID>)))" as sysdba
where:
<PASSWORD>: the password of user sys as entered in the UI
<HOSTNAME>: the host name as entered in the UI
<PORT#>: the port number as entered in the UI
<SID>: the SID as entered in the UI
- Loc

Grid Control with Oracle XE?

I've just installed Oracle Express Edition and looks great. Can i connect it to a management server (grid control)?

As curious as I always am, I was able to discover my XE database from the GC 10.1.0.4 last month. I did this because I asked myself the same question. When there is time, I normally will try everything that says "Not supported" or "Not compartible" to prove it right or wrong. So give it a go, but don't post errors from it here :-). I have not tried it for GC 10.2.0.2, but it worked on 10.1.0.4 (hopefully 10.1.0.3).
Remember, XE has all the features of EE, but a cutdown version. It has an Oracle Service and a Listener on a port, so the agent will pick them up. I have tried all possible things and tools (Forms, Reports, Designer Repository, Jdeveloper, SQL Developer, ODBC, JDBC etc) on XE to break it, but it works like EE. The only difference is when you hit the max allowed 4GB (excluding 1GB system) and I proved the limit right by kicking of a data load into a table using a cursor until it hit the maximum 4GB limit error.

11g Grid Control with Dataguard

Similar Messages

Maybe you are looking for