1200AP Reload Reason: FAILED CRYPTO INIT.

The AP restarts every 30 seconds...just like the documentation says it will!! This AP will not have full capability in LWAPP mode so I need to be able to get it to Autonomous mode but cannot get it from rebooting..... What is the process to get into a limited access mode to reload the proper security into flash and have it come up in autonomous mode??? Please let me know if you need more info...

if you want to return an ap to atonomous mode you will need to use the mode button:
http://www.cisco.com/en/US/docs/wireless/access_point/12.2_15_JA/configuration/guide/s15trb.html#wp1040300

Similar Messages

AIR-AP1131AG-A-K9 Reload Reason: FAILED CRYPTO INIT.

Hi All,
I have a standalone AP of model AIR-AP1131AG-A-K9 and have changed the mode to LAP by using mannual archive command. However after changing the mode to LAP it gives below log and keep on booting.
Reload requested by LWAPP CLIENT. Reload Reason: FAILED CRYPTO INIT.
> I did found from below link that the reason is as mentioned in point number 9, however solution didnt worked.
http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a00808f8599.shtml
> I did downloaded CiscoAironet-AP-to-LWAPP-Upgrade-Tool-v34.exe to upgrade but after executing this file nothing happens.
Kindly help me in understanding whats going wrong with my AP?
Here is the logs.
*Mar 1 00:00:06.644: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:07.644: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
ap>
*Mar 1 00:00:18.603: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:00:24.691: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:24.711: LWAPP_CLIENT_ERROR_DEBUG: lwapp_crypto_init_ssc_keys_and_certs no certs in the SSC Private File
*Mar 1 00:00:24.711: LWAPP_CLIENT_ERROR_DEBUG:
*Mar 1 00:00:24.711: lwapp_crypto_init: PKI_StartSession failed
*Mar 1 00:00:24.729: %SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: FAILED CRYPTO INIT.
*Mar 1 00:00:24.729: %LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.

One of the errors is saying that it can't find any SSC in the private file.
This yells me the AP doesn't have a certificate. Why you'll want ti do is reload an IOS image on the AP and then use the conversion tool to load the capwap image. By using the conversion tool, it wil execute some commands that create a SSC, a self signed certificate. Then you load the SSC on the WLC and the AP should be able to boot up and join.
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
Sent from Cisco Technical Support iPhone App

1130AG not joining controller - FAILED CRYPTO INIT

I am trying to join my 1130AG-E-K9 AP to my 2016 WLC, but it is stuck in a boot loop and will not connect to the controller. The error I'm getting is:
*Mar 1 00:00:29.584: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:00:29.585: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:29.598: %LWAPP-3-CLIENTERRORLOG: LWAPP Crypto Init (SSC): no certs in the SSC Private File
*Mar 1 00:00:29.598: %LWAPP-3-CLIENTERRORLOG: LWAPP Crypto Init: could not start PKI session
*Mar 1 00:00:29.598: %LWAPP-3-CLIENTERRORLOG: Failed to initialize Crypto. Rebooting
*Mar 1 00:00:29.663: %SYS-4-PUPDATECLOCK: Periodic Clock update with ROMMON failed, because size left in ROMMON (4294967295), size needed (29), error code (-1)
*Mar 1 00:00:29.663: %SYS-5-RELOAD: Reload requested by CAPWAP CLIENT. Reload Reason: FAILED CRYPTO INIT.
*Mar 1 00:00:29.664: %LWAPP-5-CHANGED: CAPWAP changed state to DOWNXmodem file system is available.
I found some details here: http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a00808f8599.shtml, but I'm not sure what it means that I have a 'SSC AP'. I am not local to this AP, though I do have a console connection to it-what do I need to do to get it working again? It just continually goes through this error and reboots every 30 seconds or so, so it's useless at the moment.
Thanks!

While that did help me potentially debug the AP, it seems the AP can not/is not reaching the WLC. Debugs on the WLC show other APs talking to it, but the only signature I'm picking up on the WLC from this AP is:
*Aug 08 20:34:36.376: 00:13:5f:fb:b4:f0 Echo Request from 10.50.0.25:44194
*Aug 08 20:34:36.376: 00:13:5f:fb:b4:f0 Echo Response sent to 10.50.0.25:44194
And from the AP itself:
Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:06.475: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event (contains, 1024 messages)
*Mar 1 00:00:08.523: %LINK-3-UPDOWN: Interface FastEthernet0, changed state up
*Mar 1 00:00:08.548: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.4(21a)JA2, RASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:17 by prod_rel_team
*Mar 1 00:00:09.523: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthet0, changed state to down
*Mar 1 00:00:17.310: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthet0, changed state to up
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:20.591: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTRER
Writing out the event log to nvram...
*Mar 1 00:00:29.591: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTLER
*Mar 1 00:00:29.592: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:29.605: %LWAPP-3-CLIENTERRORLOG: LWAPP Crypto Init (SSC): no ce in the SSC Private File
*Mar 1 00:00:29.605: %LWAPP-3-CLIENTERRORLOG: LWAPP Crypto Init: could not st PKI session
*Mar 1 00:00:29.605: %LWAPP-3-CLIENTERRORLOG: Failed to initialize Crypto. Roting
*Mar 1 00:00:29.666: %SYS-4-PUPDATECLOCK: Periodic Clock update with ROMMON led, because size left in ROMMON (4294967295), size needed (29), error code (
*Mar 1 00:00:29.667: %SYS-5-RELOAD: Reload requested by CAPWAP CLIENT. Reloaeason: FAILED CRYPTO INIT.
*Mar 1 00:00:29.667: %LWAPP-5-CHANGED: CAPWAP changed state to DOWN
Is my only option at this point reverting back to a standalone image, then going back to a LW one?
Thanks again,
-Ryan

*ERROR* Failed m_WaveList- Init(). hr=0x80040154 with Cisco TSP

Cisco TSP 8.6(2.2).
I am trying to install Cisco TSP on a Windows 7 32bit workstation, but I am having issues. We are using a management program called "Connectwise". My boss wants to be able to dial a customer within the "Connectwise" program to log calls. Our other office has a Shortel phone system and Shortel's TSP program works fine. I've installed Cisco TSP, configured CTI ports, configured a CTI routepoint, enabled the user for CTI, and associated the user with the CTI ports/route point. When I try to dial a number within Connectwise, nothing happens. Within the Cisco TSP logs these errors are logged:
16:23:36.418 HDR|05/07/2012 CiscoTSP001.tsp,Error
16:23:36.418 |   CSelsiusTSPWaveList::Init() *ERROR* Failed to get ISelsiusNTWaveCtl interface.
16:23:36.419 |   SelsiusTSP::InitializeComObjects() *ERROR* Failed m_WaveList->Init(). hr=0x80040154
17:02:12.513 |   CSelsiusTSPLink::getMessage() *ERROR* Receive() failed with error 0.
I have tried to use the Windows "Dialer" program to test as well, but receive this error:
One or more telephone device drivers are incompatible with TAPI.DLL. Install an updated version.
I have installed Cisco TSP with both the WAVE driver and the new MEDIA driver. I receive the same error with either driver. I've also tried this on multiple workstations, but get the same error.
Help

I engaged TAC and the engineer pinpointed following error from the CTI Logs:
Login User Id:platju Reason code.:-1932787595
This is the Cisco documentation on this error code:
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/jtapi_dev/8_6_1/constantfieldvalues.html
The engineer suspected LDAP server is not able to authenticate CTI based connections correctly although HTTP based connections (CCMUSER Web Page access) or JTAPI based connections (UCCX) are working fine.
We created an application user in CUCM and the Dialer.exe showed Cisco Line as expected. The engineer did assign all CTI roles (Not only Standard CTI Enabled) except Secure CTI ones. The End User didn't work no matter what we try.
As of now, I've asked the AD team to look at their side or engage Microsoft to debug it at their end. Hopefull that'll resolve the issue.

[SOLVED] luksOpen device-mapper reload ioctl failed invalid argument

Hello,
I don't know what things I have problem.
Have You any idea?
What I need to do?
$ sudo cryptsetup luksOpen /dev/sr0 dvd
Jelszó:
Enter passphrase for /dev/sr0:
device-mapper: reload ioctl failed: invalid argument
$ sudo cryptsetup luksDump /dev/sr0
LUKS header information for /dev/sr0
Version: 1
Cipher name: aes
Cipher mode: cbc-essiv:sha256
Hash spec: sha1
Payload offset: 2056
MK bits: 256
MK digest: b5 3e d0 e4 d4 e0 ed 52 25 68 88 af 74 01 90 a7 a7 e2 50 19
MK salt: 74 8e 97 56 48 b8 ad eb a9 dc 18 85 e3 a2 e9 03
7a 87 0d df d9 e3 04 e1 87 6e ce c8 3a f5 1d 6d
MK iterations: 15375
UUID: 1ef0225c-328f-4531-9d76-7259dd381960
$ cat /proc/crypto
name : sha256
driver : sha256-generic
module : sha256_generic
priority : 0
refcnt : 1
selftest : passed
type : shash
blocksize : 64
digestsize : 32
name : sha224
driver : sha224-generic
module : sha256_generic
priority : 0
refcnt : 1
selftest : passed
type : shash
blocksize : 64
digestsize : 28
name : cbc(aes)
driver : cbc(aes-asm)
module : kernel
priority : 200
refcnt : 1
selftest : passed
type : givcipher
async : no
blocksize : 16
min keysize : 16
max keysize : 32
ivsize : 16
geniv : eseqiv
name : cbc(aes)
driver : cbc(aes-asm)
module : cbc
priority : 200
refcnt : 1
selftest : passed
type : blkcipher
blocksize : 16
min keysize : 16
max keysize : 32
ivsize : 16
geniv : <default>
name : aes
driver : aes-asm
module : aes_i586
priority : 200
refcnt : 1
selftest : passed
type : cipher
blocksize : 16
min keysize : 16
max keysize : 32
name : aes
driver : aes-generic
module : aes_generic
priority : 100
refcnt : 1
selftest : passed
type : cipher
blocksize : 16
min keysize : 16
max keysize : 32
name : stdrng
driver : krng
module : kernel
priority : 200
refcnt : 2
selftest : passed
type : rng
seedsize : 0
Last edited by gyurman (2011-12-03 11:54:18)

Have you tried:
sudo cryptsetup -r luksOpen /dev/sr0 dvd

TS4123 A recent download of an iTines update - for whatever reason - failed on my computer. Since then I get a system error statement telling me that the program cannot open because 'MSVCR80.d11' is missing from my computer. When I attempt to open iTune

A recent download of an iTunes update, for some unknown reason, failed on my computer. Since then I get a system error message everytime I log on telling me that the program cannot be opened because 'MSVCR80.d11' is missing from my computer. When I try to open iTunes I get an 'error 7 (Windows error 126)' message and am advised to reinstall iTunes. However, when I attempt to do this, it downloads the programme and gets as far as installation, at which point I get yet another message: this time 'Service Apple Mobile Device failed to start'.
I am at a loss to know what to try next and would appreciate any assistance. I'm also concerned that, in the process of reinstalling iTunes, I am going to lose all the music I have collected over the years.

Click here and follow the instructions. You may need to completely remove and reinstall iTunes and all related components, or run the process multiple times; this won't normally affect its library, but that should be backed up anyway.
(99602)

IBot fails on init block

Hi, I have configured authentification against LDAP. User Administrator is defined at BI Server. When I create and run (as Administrator) an iBot it fails at init block - LDAP authentification. Can somebody help me what is wrong? I might have entered wrong password somewhere in configuration of Scheduler I try to reenter it everywhere where I found it.
Error Message:
+++ ThreadID: 506 : 2008-09-17 08:21:01.220 [nQSError: 77006] Oracle BI Presentation Server Error: A fatal error occurred while processing the request. The server responded with: Odbc driver returned an error (SQLDriverConnectW). Error Codes: OPR4ONWY:U9IM8TAC State: 08004. Code: 10018. [NQODBC] [SQL_STATE: 08004] [nQSError: 10018] Access for the requested connection is refused. *[nQSError: 13024] Successful completion of init block 'sib_Authentication LDAP' is required.* (08004) Error Codes: . Error Codes: AGEGTYVF
+++ ThreadID: 506 : 2008-09-17 08:21:01.254 iBotID: /users/administrator/_ibots/Test1 ...Trying iBot RunCR loop again.
+++ ThreadID: 506 : 2008-09-17 08:21:01.272 ... Sleeping for 8 seconds.
+++ ThreadID: 506 : 2008-09-17 08:21:09.799 [nQSError: 77006] Oracle BI Presentation Server Error: A fatal error occurred while processing the request. The server responded with: Odbc driver returned an error (SQLDriverConnectW). Error Codes: OPR4ONWY:U9IM8TAC State: 08004. Code: 10018. [NQODBC] [SQL_STATE: 08004] [nQSError: 10018] Access for the requested connection is refused. [nQSError: 13024] Successful completion of init block 'sib_Authentication LDAP' is required. (08004) Error Codes: . Error Codes: AGEGTYVF
+++ ThreadID: 506 : 2008-09-17 08:21:09.830 iBotID: /users/administrator/_ibots/Test1 ...Trying iBot RunCR loop again.
+++ ThreadID: 506 : 2008-09-17 08:21:09.845 ... Sleeping for 6 seconds.
+++ ThreadID: 506 : 2008-09-17 08:21:16.399 [nQSError: 77006] Oracle BI Presentation Server Error: A fatal error occurred while processing the request. The server responded with: Odbc driver returned an error (SQLDriverConnectW). Error Codes: OPR4ONWY:U9IM8TAC State: 08004. Code: 10018. [NQODBC] [SQL_STATE: 08004] [nQSError: 10018] Access for the requested connection is refused. [nQSError: 13024] Successful completion of init block 'sib_Authentication LDAP' is required. (08004) Error Codes: . Error Codes: AGEGTYVF
+++ ThreadID: 506 : 2008-09-17 08:21:16.419 iBotID: /users/administrator/_ibots/Test1 Exceeded number of request retries.
+++ ThreadID: 1376 : 2008-09-17 08:21:16.437 iBotID: /users/administrator/_ibots/Test1 No Content for user : Administrator

I don't think it is going to work unless you create the user in LDAP server. I am afraid this is the way your system is setup. If you want LDAP authentication then all your users need to exist there. Delivers runs iBots "on behalf" of users therefore the BI Server will try to authenticate them uding your defined LDAP authentication methods. I will suggest you don't use your OBIEE Administrator user to schedule iBots. Instead create a new user, which should exist in your LDAP server, and make this user part of the BI Server Administrator group. You should have the same priviledges as the Administrator.

Esscmd failing to init

Hi all:
I have an user who gets this message when trying to load Esscmd from command lines:
"Error: unable to init client"
All others users have essmcd with same version working OK. The version is 5.0.2. He had version 6.5.4.7 which was uninstalled because it didnt work either, under the error "Failed in GCInit(). return code [10]".
This same user has on the same machine Application Manager working ok.
Which requirements does esscmd to be able to load? Any specific port opened? any registered dll wichs registration might failed?
Thanks in advance!
Jorge

User logged in as different user, and esscmd worked ok. So it was either a persmissions issue or essbase not properly installed for all users.

Tracking reload reason

Hi all!
My 3550 reloaded and I cannot figure out how:
#sh verCisco IOS Software, C3550 Software (C3550-IPSERVICES-M), Version 12.2(25)SEC2, RELEASE SOFTWARE (fc1)Copyright (c) 1986-2005 by Cisco Systems, Inc.Compiled Wed 31-Aug-05 08:17 by antoninoROM: Bootstrap program is C3550 boot loaderSW uptime is 22 hours, 35 minutesSystem returned to ROM by power-onSystem restarted at 16:05:52 MSK Wed May 9 2012System image file is "flash:/c3550_ipservices_mz.122_25.SEC2.bin"Cisco WS-C3550-24 (PowerPC) processor (revision R0) with 65526K/8192K bytes of memory.Processor board ID CAT0926N2WBLast reset from warm-resetRunning Layer2/3 Switching ImageEthernet-controller 1 has 12 Fast Ethernet/IEEE 802.3 interfacesEthernet-controller 2 has 12 Fast Ethernet/IEEE 802.3 interfacesEthernet-controller 3 has 1 Gigabit Ethernet/IEEE 802.3 interfaceEthernet-controller 4 has 1 Gigabit Ethernet/IEEE 802.3 interface24 FastEthernet interfaces2 Gigabit Ethernet interfacesThe password-recovery mechanism is enabled.384K bytes of flash-simulated NVRAM.Base ethernet MAC Address: 00:14:F2:12:E2:80Motherboard assembly number: 73-5700-12Power supply part number: 34-0966-04Motherboard serial number: CAT09270017Power supply serial number: LIT09230F1NModel revision number: R0Motherboard revision number: A0Model numbeWBConfiguration register is 0x10Fr: WS-C3550-24-SMISystem serial number: CAT0926N2
this indicates what someone type "reload command"
Last reset from warm-reset
but I can't see anything about it in logs
09.05.12 16:05:32 - Cisco IOS Software, C3550 Software (C3550-IPSERVICES-M), Version 12.2(25)SEC2, RELEASE SOFTWARE (fc1) 09.05.12 16:05:32 - *Mar 1 04:00:41: %SYS-5-RESTART: System restarted -- 09.05.12 16:05:32 - *Mar 1 04:00:40: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1010, changed state to down 09.05.12 16:05:32 - *Mar 1 04:00:40: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1000, changed state to down 09.05.12 16:05:32 - *Mar 1 04:00:40: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan555, changed state to down 09.05.12 16:05:32 - *Mar 1 04:00:40: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan41, changed state to down 09.05.12 16:05:32 - *Mar 1 04:00:40: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan35, changed state to down 09.05.12 16:05:32 - *Mar 1 04:00:40: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan34, changed state to down 09.05.12 16:05:32 - *Mar 1 04:00:40: %GBIC_1000BASET-6-GBIC_1000BASET_DEFAULT_CONFIG: 1000-BaseT GBIC module is detected in Gi0/2. Speed and duplex will be autonegotiated 05.04.12 14:41:10 - Apr 5 14:42:27: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1010, changed state to up 05.04.12 10:58:19 - Apr 5 10:59:36: %SYS-5-CONFIG_I: Configured from console by username on vty0 (81.28.160.110) 05.04.12 10:58:19 - Apr 5 10:59:36: %PARSER-5-CFGLOG_LOGGEDCMD: User:username logged command:exit
may be Im not clearly understood 'last reset from warm reset' reason? (if it was power failure there must be "Last reset from power-on")
Best regards, Maxim.

Maxim,
Can you do a "show warm-boot"? If it says warm-boot is enabled, you may want to look at this link:
http://www.cisco.com/en/US/docs/ios/12_3t/12_3t2/feature/guide/gtwrmrbt.html
The above command will show you if the system has been rebooting due to crashes, etc. This doesn't rule out someone reloaded the switch manually, but it may give you a little more to go on.
HTH,
John

Has anyone encountered Redwood suddenly and for no apparent reason failing to start a previously running job

Hi
We've seen this on a number of occassions -our Redwood system suddenly stops running a job that was previously running with no issue. - has anyone else encountered this issue before? - We have been unable to find any documents detailing parameter that might be controlling this ? -
We are on Redwood 7.30.7 version
Any assistance greatly appreciated.
Cheers
Conor

Hey Conor,
First thing your Build version. It is very old and a lot of bugs have been fixed now.
Current available build is M33.104. Please do upgrade.
Have you searched SAP notes for your version? If it is a bug it would have been mentioned in the note for the next build version.
What do you mean the job suddenly stops? What do you see in the job status?
Is it a recurring job? Have you checked the schedule calendar of the particular job in status area?
Also make sure, the time window on which is the job is running is closed for that time.
Also check the submit frame. Submit frame is closed if the corresponding time window is closed.
Thanks
Nanda

IPlanet WebServer fails to init Oracle Connection

Hi,
I've deployed a Servlet in iWS 6.0, that uses a connection to an Oracle Server 9i (classes12.jar).
When I try to access the database I receive an error like:
[08/Jul/2002:21:05:18] failure (12007): Internal error: Unexpected error condition thrown (unknown exception,no description), stack: java.lang.StackOverflowError
at java.lang.ClassLoader.loadClass(ClassLoader.java:250)
at java.lang.ClassLoader.loadClassInternal(ClassLoader.java:310)
at java.lang.ClassLoader.defineClass0(Native Method)
at java.lang.ClassLoader.defineClass(ClassLoader.java:488)
at java.lang.ClassLoader.defineClass(ClassLoader.java:423)
at com.iplanet.server.http.servlet.NSServletLoader.loadResource(NSServletLoader.java:387)
at com.iplanet.server.http.servlet.NSServletLoader.loadClass(NSServletLoader.java:429)
at com.iplanet.server.http.servlet.NSServletLoader.findClass(NSServletLoader.java:174)
at com.iplanet.server.http.servlet.NSServletLoader.loadClass(NSServletLoader.java:106)
at java.lang.ClassLoader.loadClass(ClassLoader.java:250)
at java.lang.ClassLoader.loadClassInternal(ClassLoader.java:310)
at java.lang.ClassLoader.defineClass0(Native Method)
at java.lang.ClassLoader.defineClass(ClassLoader.java:488)
at java.lang.ClassLoader.defineClass(ClassLoader.java:423)
at com.iplanet.server.http.servlet.NSServletLoader.loadResource(NSServletLoader.java:387)
at com.iplanet.server.http.servlet.NSServletLoader.loadClass(NSServletLoader.java:429)
at com.iplanet.server.http.servlet.NSServletLoader.findClass(NSServletLoader.java:174)
at com.iplanet.server.http.servlet.NSServletLoader.loadClass(NSServletLoader.java:106)
at java.lang.ClassLoader.loadClass(ClassLoader.java:250)
at java.lang.ClassLoader.loadClassInternal(ClassLoader.java:310)
at java.lang.ClassLoader.defineClass0(Native Method)
at java.lang.ClassLoader.defineClass(ClassLoader.java:488)
at java.lang.ClassLoader.defineClass(ClassLoader.java:423)
at com.iplanet.server.http.servlet.NSServletLoader.loadResource(NSServletLoader.java:387)
at com.iplanet.server.http.servlet.NSServletLoader.loadClass(NSServletLoader.java:429)
at com.iplanet.server.http.servlet.NSServletLoader.findClass(NSServletLoader.java:174)
at com.iplanet.server.http.servlet.NSServletLoader.loadClass(NSServletLoader.java:106)
at java.lang.ClassLoader.loadClass(ClassLoader.java:250)
at java.lang.ClassLoader.loadClassInternal(ClassLoader.java:310)
at oracle.jdbc.driver.OracleConnection.privateCreateStatement(OracleConnection.java:763)
at oracle.jdbc.driver.OracleConnection.createStatement(OracleConnection.java:670)
I thought that the problem could be classpath configuration (classes12.jar is in the WEB-INF of my Web Application), so I put classes12.jar in the classpath of the application, the error changes and now I can see:
[08/Jul/2002:21:31:40] failure (12159): Internal error: Unexpected error conditi
on thrown (unknown exception,no description), stack: java.lang.StackOverflowErro
r
at java.net.URLClassLoader$1.run(URLClassLoader.java:187)
at java.security.AccessController.doPrivileged(Native Method)
at java.net.URLClassLoader.findClass(URLClassLoader.java:183)
at java.lang.ClassLoader.loadClass(ClassLoader.java:294)
at java.lang.ClassLoader.loadClass(ClassLoader.java:287)
at sun.misc.Launcher$AppClassLoader.loadClass(Launcher.java:281)
at java.lang.ClassLoader.loadClass(ClassLoader.java:250)
at java.lang.ClassLoader.loadClassInternal(ClassLoader.java:310)
at java.lang.ClassLoader.defineClass0(Native Method)
at java.lang.ClassLoader.defineClass(ClassLoader.java:488)
at java.security.SecureClassLoader.defineClass(SecureClassLoader.java:106)
at java.net.URLClassLoader.defineClass(URLClassLoader.java:243)
at java.net.URLClassLoader.access$100(URLClassLoader.java:51)
at java.net.URLClassLoader$1.run(URLClassLoader.java:190)
at java.security.AccessController.doPrivileged(Native Method)
at java.net.URLClassLoader.findClass(URLClassLoader.java:183)
at java.lang.ClassLoader.loadClass(ClassLoader.java:294)
at sun.misc.Launcher$AppClassLoader.loadClass(Launcher.java:281)
at java.lang.ClassLoader.loadClass(ClassLoader.java:250)
at java.lang.ClassLoader.loadClassInternal(ClassLoader.java:310)
at java.lang.ClassLoader.defineClass0(Native Method)
at java.lang.ClassLoader.defineClass(ClassLoader.java:488)
at java.security.SecureClassLoader.defineClass(SecureClassLoader.java:106)
at java.net.URLClassLoader.defineClass(URLClassLoader.java:243)
at java.net.URLClassLoader.access$100(URLClassLoader.java:51)
at java.net.URLClassLoader$1.run(URLClassLoader.java:190)
at java.security.AccessController.doPrivileged(Native Method)
at java.net.URLClassLoader.findClass(URLClassLoader.java:183)
at java.lang.ClassLoader.loadClass(ClassLoader.java:294)
at sun.misc.Launcher$AppClassLoader.loadClass(Launcher.java:281)
at java.lang.ClassLoader.loadClass(ClassLoader.java:250)
at java.lang.ClassLoader.loadClassInternal(ClassLoader.java:310)
at java.lang.Class.forName0(Native Method)
at java.lang.Class.forName(Class.java:115)
at oracle.jdbc.driver.OracleDriver.getConnectionInstance(OracleDriver.java:442)
at oracle.jdbc.driver.OracleDriver.connect(OracleDriver.java:332)
at java.sql.DriverManager.getConnection(DriverManager.java:512)
at java.sql.DriverManager.getConnection(DriverManager.java:141)
at oracle.jdbc.pool.OracleDataSource.getConnection(OracleDataSource.java:150)
at oracle.jdbc.pool.OracleDataSource.getConnection(OracleDataSource.java)
Thanks a lot,
David.

put classes12.jar path in jvm12.conf file of web server. You can configure this through GUI also. try renaming classes12.jar to classes12.zip also
Ananda Rao

Converting to LWAPP (Aironet 1231)

I currently manage 115 Aironet AP1231-G-A-K9 WAP's via WLSE. We had a site assessment done, and they are recommending two wireless controllers for management with Cisco 3500 WAP's with clean air technology. I agree with recommendations, but I do not want to replace 115 access points. Has anyone ever successfully converted the 1231's to LWAPP?
I see there are utilites to accomplish this, but I also see alot of incompatibility post. Any comments/advice is greatly appreciated.
Kind Regards,
John

I am really appreciated for your helps Scott
Here is the output from AP.
*Mar 1 00:00:04.781: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1200 Software (C1200-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:41 by alnguyen
*Mar 1 00:00:05.716: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:06.716: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:23.804: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:23.818: LWAPP_CLIENT_ERROR_DEBUG: lwapp_crypto_init_ssc_keys_and_certs no certs in the SSC Private File
*Mar 1 00:00:23.818: LWAPP_CLIENT_ERROR_DEBUG:
*Mar 1 00:00:23.818: lwapp_crypto_init: PKI_StartSession failed
*Mar 1 00:00:23.990: %SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: FAILED CRYPTO INIT.
*Mar 1 00:00:23.990: %LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.
flashfs[0]: 5 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 7741440
flashfs[0]: Bytes used: 1864192
flashfs[0]: Bytes available: 5877248
flashfs[0]: flashfs fsck took 11 seconds.
Reading cookie from flash parameter block...done.
Base ethernet MAC Address: 00:11:bb:f4:2a:f5
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbs, full-duplex
Ethernet port 0 initialized: link is up
Loading "flash:/c1200-rcvk9w8-mx/c1200-rcvk9w8-mx"...#########################################################################################################################################################################
File "flash:/c1200-rcvk9w8-mx/c1200-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
executing...
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
I currently have 42 APs online now.

Cisco 1200 series upgrade failure

I have a Cisco 1200 Series (AIR-AP1231G-A-K9) access point, I have been upgrading these models to lightweight mode but are having issues with one in particular, this access point keeps "rebooting" itself, I am assuming that the upgrade faild, how can I get the access point upgraded?
Here is a capture.
Cisco IOS Software, C1200 Software (C1200-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:41 by alnguyen
Image text-base: 0x00003000, data-base: 0x00359FC0
Initializing flashfs...
flashfs[1]: 4 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 7741440
flashfs[1]: Bytes used: 1862656
flashfs[1]: Bytes available: 5878784
flashfs[1]: flashfs fsck took 2 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
cisco AIR-AP1231G-A-K9 (PowerPC405GP) processor (revision B0) with 15038K/1336K bytes of memory.
Processor board ID FTX0914J0Z1
PowerPC405GP CPU at 196Mhz, revision number 0x0145
Last reset from reload
LWAPP image version 3.0.51.0
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:13:7F:E2:34:DB
Part Number : 73-8704-08
PCA Assembly Number : 800-23211-09
PCA Revision Number : A0
PCB Serial Number : FOC09100NH1
Top Assembly Part Number : 800-23304-08
Top Assembly Serial Number : FTX0914J0Z1
Top Revision Number : A0
Product/Model Number : AIR-AP1231G-A-K9
Press RETURN to get started!
*Mar 1 00:00:04.505: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1200 Software (C1200-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:41 by alnguyen
*Mar 1 00:00:05.442: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:06.442: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
ap>
ap>
*Mar 1 00:00:14.441: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:23.516: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:23.544: LWAPP_CLIENT_ERROR_DEBUG: lwapp_crypto_init_ssc_keys_and_certs no certs in the SSC Private File
*Mar 1 00:00:23.544: LWAPP_CLIENT_ERROR_DEBUG:
*Mar 1 00:00:23.544: lwapp_crypto_init: PKI_StartSession failed
*Mar 1 00:00:23.698: %SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: FAILED CRYPTO INIT.
*Mar 1 00:00:23.698: %LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.
flashfs[0]: 4 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 7741440
flashfs[0]: Bytes used: 1862656
flashfs[0]: Bytes available: 5878784
flashfs[0]: flashfs fsck took 9 seconds.
Reading cookie from flash parameter block...done.
Base ethernet MAC Address: 00:13:7f:e2:34:db
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
Loading "flash:/c1200-rcvk9w8-mx/c1200-rcvk9w8-mx"...#########################################################################################################################################################################
File "flash:/c1200-rcvk9w8-mx/c1200-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend

I might have an answer for you... or I might be COMPLETELY WRONG
If it isn't just a "failed" upgrade, as in you've tried the upgrade again and it still is happening.... I was reading something about older APs not have a Manufacturing-installed certificate (MIC) and these AP's generating a Self-signed Certificate (SSC).
The error you have is referring to SSC so I'm writing this as if you have not had to previously do this step for your other conversions.
I believe a couple of things needs to happen for SSC AP's.
1) Must enable controller to accept self-signed certificated.
Security > AAA > AP Polices > Accept Self Signed Certificate > Apply
2) Add AP to Authorization List in Security > AAA > AP Polices > Add AP To Authrorization List
Enter MAC Address of the AP
Certificate type = SSC
SHA1 Key Hash can be obtained from the controller by issueing this command:
"debug pm pki enable"
Look for the line: sshpmGetIssuerHandles: SSC Key Hash is XXXXXXXXXXXXXXXXXXXXXXXXXX
I believe you use the XXXXXXXXXXXXXXXXXXXXX as the SHA1 Key Hash.
3) If required, you may also need to add the AP MAC Address in the Mac-Filter: Security > AAA > MAC Filtering > New >
Hopefully its either a reload of the software or this SSC thing that fixes the problem....

Server failed to run - Reason:Server is not in the majority cluster partition

Hi,
my environment is Weblogic 12.1.2.
The deployment configuration is: cluster, 2 machines, 2 managed servers, 1 data source, and JMS (with uniform distributed queue).
When I'm starting the admin server + managed server on the first machine (using the node manager), while on the second machine the managed server and also the node manager are not running, the server failed to run and the error reason is : "Server is not in the majority cluster partition".
How can I enforce the server to run even if the second one is not running ? This scenario could occured because of some local problems on the second machine. My expectation is that after the second will running the whole cluster status will be good.
Thanks,
Yaakov

Hi,
Just to remember the configuration: 2 managed servers configured as cluster that should be deployed on 2 different machine.
Following summary of the tests:
     - node manager + admin server + 1 managed server running on the first machine --> server failed to init with error "Server is not in the majority cluster partition"
     - node manager + admin server + 2 managed servers running on the one machine --> servers are running without errors
     - node manager + admin server + 1 managed server running on the first machine / node manager runs on the second machine --> server on the first machine runs without errors without the famous error ' Server is not in the majority cluster partition'.
Bottom line, seems that if the node manager is not running on the remote machine, the cluster is not in a stable state and so the single managed server failed to initialize.
Is it according the documentation / expectations ?
Thanks,
Yaakov

Delta Init failed

Hi All:
I don't understand the reason behind delta Init Failure. source system check is also OK. Message reads
ransfer Idocs and TRFC : Errors Occured
Request IDoc: Application document not posted
Info Doc 1: Application document posted.
 Also extraction tab is red and this reads Error occurred in the data selection
Thanks!
Manasa.

Replicating datasource didn't do good. I did Full update but It's not allowing to do Init.With full upload I tried to see the data in ODS, this message is stopping me.
""Your user master record is not sufficiently maintained for object""
Thanks,
Manasa.

1200AP Reload Reason: FAILED CRYPTO INIT.

Similar Messages

Maybe you are looking for