120N Access Restriction tab gone

I have used it before and I am not aware of any changes (not counting kids since who knows). The tab is completely gone, not greyed out just gone. How do I get it back?
Firmware is1.0.04
I have reset, I have powered down. Is there something else I should try?
As well now that the tab is missing does that mean what was setup on it is now null?

Try to reflash the router's firmware.You can download the firmware from linksys website.After reflashing the firmware,reset the router for 30-35 seconds,Power Cycle the router and check again.I hope this will resolve the issue.

Similar Messages

  • Wrt610n after upd to 2.00.01 tab "Access Restrictions" was gone

    Hello. I decided to update firmware on wrt610n from 2.00.00 B05 to 2.00.01. After it - tab "Access Restrictions" was gone. Can I use this function on this version? If not where I could download firmware by 2.00.00 B05 version?
    Solved!
    Go to Solution.

    Seems weird. I’ve checked on the release notes and FW version 2.0.01 B015 included a fixed on access restrictions. Have you tried powering off and on the router after the update? If power cycle won’t work, you would need to press and hold the reset button for 30 seconds and totally reconfigure the router’s settings. All tabs should be present after reset since it would restore all settings back to factory defaults.

  • Access Restriction tab is missing on e3000 web interface

    I am quite sure that this tab has been there before but now its missing - could it be because I have activated  Parent Control on Cisco Connect ?
    If so - how do I 'get It back'
    (I thing parent control in Cisco connect is too limited)
    Regards
    Fleohans
    Solved!
    Go to Solution.

    Yes, the Access Restrictions tab goes away when the Parental Controls section is activated. According to the faqs, a hard reset is the only way to restore it.

  • WRT310N Access Restriction tab

    I just recently updated the firmware in my router from 1.0.04 to the newest 1.0.07 build 14. I felt the need to update since my router would randomly stop broadcasting a wireless signal and after a few minutes come back. but that's not the issue, since the new firmware doesn't do this(yet, *crosses fingers*). 
    Since the update, I've noticed one thing. The "access restriction" feature on the router isn't there anymore. Live support says they've never seen that happen before, and directed me to the HDN stuff on the LELA software(After telling me to do the standard stuff for 5 minutes). I see the feature kind of available in there in a more "user-friendly" way. I don't understand how the feature could be missing on the main GUI but available through some software. I, personally cannot warrant paying for the HDN stuff just for the access restriction tab controls that were previously free and continue to be free on other routers, and most other people probably don't as well. But I'm interested in seeing if others have noticed this as well and what the general community thought is about this.
    Solved!
    Go to Solution.

    When you reset your router to factory defaults it goes back to the old firmware 1.0.04...With the old firmware if you don't have any issues then try to upgrade your router to the latest firmware...Wait another next firmware release...
    However, if you have any issues with the old firmware then you should try to upgrade your router with the TFTP Utility...
    Download TFTP Utility
    Download Firmware 3.23 MB...
    Double click the tftp.exe file and click run :
    For Server- Enter the IP Address of the router that you assigned.  By default, the router is 192.168.1.1...
    For Password- Enter the password you assigned the router. By default, the router’s password is “admin”.
    For File- Click the triple “…” button and browse for the .bin firmware file...
    Click Upgrade button to start upgrading.  A progress bar should show up to show the progress.
    Once the Upgrade is done press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...See if this works...

  • E1200 v2 "access restrictions"

    I had a E1200, I read the articles from the support about the routers, I think the "access Restrictions" has more flexiable to setup on for the parental control, after chated to cisco support person onlin, I was told that the E1200 v2 has this "access restrictions" function, and I wan convinced to purchase from them. I did. I got the E1200 v2 recently, however, after I installed the CD and found there is no "access restrictions" tab, instead the "access policy" is still there. by the way the firmware is 2.0.02 now.
    I wonder if anybody here can help me get the "access restricions" from setup? I've chatted with cisco support person twice again, but nobody can fix the problem, one suggested to restart and reinstall the CD. I uninstalled the software, restarted the computer and resinstalled the CD. same problem, no tab of "access restrictions".
    Thanks,
    solitons

    Thank you for helping.
    I chated twice with the tech support, but didn't workout, I called them this morning, they told me to get the "Access Restrictions" I should uninstall the software, reset the router, and do manually setup on line. I follwed the instruction, but still only see the "Access Policy" there, and there is no "Access Restricions" tab, if I click on the "Access Policy", the "Parental Control" is the only thing. so the tech support concluded that it is a v1 actually, even there is a label on the router says "E1200 V2". and they issued a case number for replacement.
    Then I called for a replacement, but I have to waive the refund if I go for the replacement, and if I don't want to replace it, I can do the refund, but it will take long time.

  • Access restriction on WRT54G v6

    is any body other then me have this problem. -
     I got a WRT54G v6 to replace a d-link that not working anymore. And when I go to the Access
    Restriction tab to set up a block the manual and side note select internet acces as policy
    type, but there is no place to select it. well there be a fix in firmware (I have 1.01.1) or
    is somewrong with me unit?
    I have used windozXP with IE and linux with firefox. same on both.
    yes I hard reset for 15 sec. unpluged for about 1 min.

     mine is WRT54G v4
     the problem is the policy is not working
    so i can not block the friendsters.com

  • Downgrading firmware on WRT54G/access restrictions

    I had a WRT54G.  Access restrictions worked.  I upgraded the firmware and the access restrictions no longer worked. 
    So after researching, it appears the firmware I upgraded to was buggy and the access restrictions didn't work with the new firmware.  I couldn't figure out how to downgrade back to what I had. 
    Called Linksys and ultimately they said they would send a new router.  I asked if it would have the old firmware that my router had previously, where the access restrictions worked.  Yes, they said.
    New router arrives today.  Firmware is v1.02.2, June 7, 2007.  NOT the prior firmware.  Sure enough, the access restrictions still do not work on this router either.  I don't want to spend yet another two weeks trying to resolve this with Linksys.
    Question:  Is there a way to downgrade to firmware where the access restrictions actually work for WRT54G?  If so,
    what version should I downgrade to?
    where do I obtain it? and
    can I download the firmware and then install it using the administration/upgrade firmware tab on the router (even though it is a downgrade)?
    Thanks very much for any thoughts.

    Thanks for the suggestion, Badboy.  Unfortunately, although I could download the firmware and successfully load it onto the router, the access restrictions in that version do not work either.
    It doesn't seem as though all prior versions of firmware are on the ftp site, ftp.linksys.com.  For example, I also have a wrt54gs v. 4 (speedbooster) with the same access restriction problem.  It currently has a firmware version loaded that doesn't appear to be listed on that website.  (I couldn't download prior firmware for that version that worked.)  So, perhaps prior firmware exists for the wrt54g v. 6 that is not listed on that site also.
    Does anyone know if there is another site that has a more extensive collection of prior linksys firmware? 
    If not, I suppose I can call linksys again, but even if they send yet another router promising the old firmware on it, I suspect the message is just going to get lost between the promise made on the phone and the guy in the warehouse filling the RMA order.

  • Can't access one tab in iTunes U account

    We have an instructor who is using iTunes U to have students submit files in several different categories. Her site has tabs for each category, and as of yesterday evening, no one can access one of the tabs. Clicking on it produces the "Could not complete the iTunes Store request. The store may be busy." message. I found an old discussion (https://discussions.apple.com/thread/2026539?start=0&tstart=0) that makes me think a student may have uploaded a file that is causing the problem, but as I can't access the tab, I can't see what's been uploaded. Our iTunes U admin is in training all day, but she did indicate that when she checked last night, she could see all of the files for the tab in the Upload/Manage area, but she can't tell which file might be causing the problem.
    Does anyone have a suggestion for what might be causing this behavior, or what we can try to do to fix it?
    Thanks!

    When you select the Apps tab for your iPad sync preferences, nothing is available below even the option to select Sync Apps?
    Was this available before and this is a recent change? It must have been available before if you have Sync Apps selected under the Apps tab for your iPad sync preferences which is the only place where you can select Sync Apps for your iPad sync preferences.
    Do you have Restrictions enabled on your iPad and if so, is installing apps selected as a restriction?

  • E1000 Access Restrictions Issue

    I attempted to create a rule to limit access only to specific URLs during a specific time of day.  However, it seems to have blocked all of the internet for the user at that MAC address, outside of the times I had chosen.  I double-checked to make sure that the radio button next to 'Allow' was selected in the section that reads:  "Internet access during selected days and hours."  I don't know what I'm doing wrong.   How is the time of day determined by the router?  Is there a clock which needs to be set to my time zone somewhere?  If so, I've yet to find it.  Also, why is it blocking all access to the internet?  It should only be blocking 3 URLs.

    The Access Restrictions feature of a Linksys router allows you to limit Internet access on your network.  You can deny certain computers’ Internet access or block certain applications and services.  This article will provide instructions on how to set up Access Restrictions by blocking certain days or hours.
    Here is the link for the same: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=20b29e54474a4a17aff594cb659747ea_4041.xml&pid=80&r...
    The time zone on your router should be set correctly according to the time zone in your current location.  This is to ensure that the Parental controls feature will block Internet access on the exact time you specified.  To configure the time zone on your router, access your router’s web-based setup page, then go to Basic Setup sub tab under the Setup tab.  Click the Time Zone drop-down menu and select the appropriate time zone.  Once done, click Save Settings.

  • Restricting Tab Out

    Hi,
    Using Jdev 11.1.1.6
    I have implemented three column page template.. where my left panel has some taskflow and right have some other taskflow. My center has the af:panelTabbed , which have 3 showDetailItems.
    Each showDetailItem has a region binding, which is called dynamically on some action..
    I just wanted to ask, if there is any way that I can restrict Tab out from my CENTER i.e just Opened ShowDetailItem , to any other place in three column page template.
    More Explanation
    This is nothing to do with PanelTabbed component.... It's simple Keyboard 'TAB' I want to restrict.
    Like if user uses Tab for accessing fields on the Center screen. Then after the last field on the Center TaskflowScreen, 'TAB' goes out of the screen to next Taskflow enabled field. I want to restrict that...
    Regards,
    Neha..
    Edited by: neha on May 15, 2013 2:23 AM

    Neha,
    You could probably add a input text component in your main page (say under end / copyright facet of the pageTemplate) and set it width to 0. Add a clientListener to it which would set the focus to the first component.
    Ex:
                <af:form id="f1">
                    <af:resource type="javascript">
                      function checkTab(evt) {
                          var keyPressed = evt.getKeyCode();
                          if (keyPressed == AdfKeyStroke.TAB_KEY) {
                              var compToSetFocus = evt.getSource().findComponent('pt1:it1');
                              compToSetFocus.focus();
                          evt.cancel();
                    </af:resource>
                    <af:pageTemplate viewId="/oracle/templates/threeColumnTemplate.jspx" id="pt1">
                        <f:facet name="center">
                            <af:group id="g1">
                                <af:inputText label="Label 1" id="it1" clientComponent="true"></af:inputText>
                                <af:inputText label="Label 2" id="it2"/>
                                <af:inputText label="Label 3" id="it3"/>
                            </af:group>
                        </f:facet>
                        <f:facet name="header"/>
                        <f:facet name="end"></f:facet>
                        <f:facet name="start"/>
                        <f:facet name="branding"/>
                        <f:facet name="copyright">
                            <af:inputText id="it4" contentStyle="width:0px;">
                                <af:clientListener method="checkTab" type="keyPress"/>
                            </af:inputText>
                        </f:facet>
                        <f:facet name="status"/>
                    </af:pageTemplate>
                </af:form>-Arun

  • Access Restriction on EA3500 does not work.

    I tested this with my laptop by setting its access restriction/parental control to always not access the internet. But still my laptop can still search through wikipedia. Is this because of the router firmware? By the way I'm using the latest Connect cloud firmware. Thanks in advance.

    I believe parental control is not really busted, it's just designed to work only with ipv4. What you can try though is to try the following:
    Make sure that the laptop is only wirelessly connected to the router, because if the laptop was connected both wired and wireless then parental controls will not work since the laptop will be using two adapters.
    Remove the entry under target devices, disable parental controls and save the settings.
    Enable parental controls, add a target device, save the settings
    Try to check if you can access wikipedia or other website because if parental control was working then it should add for a password
    Try also to check the router's status tab if there's an ipv6 ip address because if there is, then parental controls will not work

  • WRT54GL Cannot get access restrictions to work

    I purchased a WRT54GL router (v1.1 with  firmware 4.30.7) and I cannot for the life of me get the access restrictions to work.  I made three policies, one for my PC with 24/7 access and one for the kids PC with access from 7pm to 9pm during the weekdays and another for the kids PC with access from 12pm to 10pm on the weekends.  whenever I enable the policies, my PC can access the internet but the kids cannot (of course during the proper times).  When I disable their policies they still cannot get on till I also disable my policy.  I have gone thru everything I can think of including multiple hard resets but access restriction simply will not work.
    Of course there is no mention of my hardware or firmware version anywhere on the linksys support system!  Anyone have any thoughts?

    hmmmmmm... have you tried using the IP address instead?  based on my experience, the Acces Restriction policies are a bit tricky. 
    Too bad the WRT54g has no parental controls which is a lot easier to configure.
    "Don't fix it if it ain't broken."

  • WRT150N Access Restrictions Not Working

    Good day everyone.
    I read posts that were similar to my problem in the forum but none of the solutions suggested solved my current quandary.
    I am using a WRT150N with firmware v1.00.5. I have a Linux setup with Squid connected to the network with the gateway 192.168.23.254. The WRT150N has a gateway of 192.168.23.1. The WRT150N is also connected to an Apple Base Station which serves as the Access Point for WiFi users.
    Squid limits access for IP addresses listed under the .254 gateway. But once I change my gateway to 23.1, everything is accessible. I want to block sites as well on the WRT150N. But every time I try to put a new Access Restriction, it doesn't work.
    I put in the IP Addresses on which to apply this restriction:
    The reason it skips addresses is because, the addresses are reserved. I click on Save Settings here and I save the settings again on the main page.
    Everytime I try to test it on the given addresses, I can still access the pages. Is there something I'm missing?
    Thank you in advance for your answers.
    Solved!
    Go to Solution.

    Try to upgrade/ re flash the firmware on your router.
    Connect computer with the Ethernet cable to the router Ethernet port.
    Download the firmware from the Linksys website .
    Open the setup page of the router.
    Go to the Administration tab and go to the sub tab Firmware upgrade.
    Browse and select the downloaded firmware and upgrade the firmware .
    After upgrading the firmware reset and reconfigure the router settings manually .
    And see if that helps you .

  • WRT54G2 and WRT54G locks-up (freezes) when blocking web sites using Access Restrictions

    I am convinced that a few Linksys routers such as WRT54G2 and WRT54G have a major issue when blocking web sites using Access Restrictions (Internet Access Policy). After a few hours of internet access by 15 wired users the Linksys locks-up and blocks all internet web access. The only solution is to restart the power on the router.
    We are currently using a Linksys WRT54G2 v1 (firmware 1.0.04). We upgraded the WRT54G2 v1 firmware to the latest 1.0.04 version which did not resolve the issue.  NOTE: We were previosuly using a a Linksys WRT54G v1.1 (firmware 4.21.1) until the power supply blew a week after we started blocking web sites using Access Restrictions (Internet Access Policy).  
    Basically, we have a T1 internet connection and a hub connected to the Linksys router. We are trying to block several web sites such as facebook, myspace, etc. for 15 wired users. We do not use wireless connections.
    This is the 2nd time it happened with 2 different models.
    Please help ASAP.
    Thank you,
    Lance
    (Mod note: Edited post. Some parts off topic.. Thanks!)

    Also,  you have already upgrade/re-flash the firmware of your Linksys Router you need to reset and reconfigure your router from scratch. Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

  • How to configure CLI/DNIS based access restriction in 5.3 ?

    Hi,
    does anybody have an idea how the setting
    define CLI/DNIS-based access restrictions which is defined in ACS v. 4.2
    can be configured in acs 5.3 ?
    in v. 4 for every user in a group with 40 members  a different CLI is defined for each. How can I configure that in version 5.3 ?
    any help as always much appreciated!

    The equivalebt to NAR functionality can be found at:
    Policy Elements > Session Conditions > Network Conditions > End Station Filters
    Can then define an object with a set of CLI values
    These objects can then be used in policy conditions. So can create a condition with a set of CLI values and then match in authorization policy for values that are included in this set and set authorizations accoridngly
    Not sure if this is your use case but hopefully may be a start

Maybe you are looking for