1252 Access point bridge problems

Hello
Currently im trying to deploy solution for external people as somethink like quest connection (in config name is public.net)
The only spare AP i have is cisco 1252
After research in setup whitchport as trunk for management vlan (which must be done) and for me entire config seems to be good. Im able to connect to ssid, but im unable to browse web, when connected.(still receiving 169. ip addres)
Im able to ping default gateway,able to ping dhcp server. Think is, when checking bridge, receiving is ok, but nothing is being transmitted.
Vlan 192 is our vlan just for public conenction, works correctly on other aps.
Btw same problem is have with 1142.
I think there must me missing something specific for this two models (as was that management vlan must be native on switch side)
any ideas please?
dot11 ssid public.net
   vlan 192
   authentication open
   authentication key-management wpa
   mbssid guest-mode
   wpa-psk ascii 0 on2access@wpa!
dot11 aaa csid ietf
dot11 network-map 60
bridge irb
interface Dot11Radio0
 no ip address
 no ip route-cache
 encryption vlan 192 mode ciphers tkip
 ssid public.net
 speed basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
 channel 2412
 station-role root
 rts threshold 2312
 world-mode dot11d country SK both
 bridge-group 1
 bridge-group 1 block-unknown-source
 no bridge-group 1 source-learning
 no bridge-group 1 unicast-flooding
 bridge-group 1 spanning-disabled
interface Dot11Radio0.192
 encapsulation dot1Q 192
 no ip route-cache
 bridge-group 192
 bridge-group 192 subscriber-loop-control
 bridge-group 192 block-unknown-source
 no bridge-group 192 source-learning
 no bridge-group 192 unicast-flooding
 bridge-group 192 spanning-disabled
interface Gi0
 no ip address
 no ip route-cache
 duplex auto
 speed auto
 bridge-group 1
 no bridge-group 1 source-learning
 bridge-group 1 spanning-disabled
interface Gi0.16
 encapsulation dot1Q 16
 no ip route-cache
 bridge-group 1
 no bridge-group 1 source-learning
 bridge-group 1 spanning-disabled
interface Gi0.192
 encapsulation dot1Q 192
 no ip route-cache
 bridge-group 192
 no bridge-group 192 source-learning
 bridge-group 192 spanning-disabled
interface BVI1
 ip address 10.250.16.68 255.255.255.0
 no ip route-cache

Hi
Try to add following & see
interface Gi0.16
 encapsulation dot1Q 16 native
int d0.16
encapsulation dot1Q 16 native
bridge-group 1
Also if "ip default-gateway x.x.x.x" command is missing add that as well. Here is a basic configuration without any added security.
dot11 ssid TEST
   vlan 143
   authentication open
   guest-mode
interface Dot11Radio1
 ssid TEST
interface Dot11Radio1.143
 encapsulation dot1Q 143
 bridge-group 143
interface Dot11Radio1.999
 encapsulation dot1Q 999 native
 bridge-group 1
interface GigabitEthernet0.143
 encapsulation dot1Q 143
 bridge-group 143
interface GigabitEthernet0.999
 encapsulation dot1Q 999 native
 bridge-group 1
interface BVI1
 ip address 192.168.99.99 255.255.255.0
ip default-gateway 192.168.99.1
HTH
Rasika
**** Pls rate all useful responses *****

Similar Messages

  • How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

    How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

    The Guest Network function of the Time Capsule and AirPort Extreme cannot be enabled when the device is in Bridge Mode. Unfortunately, with another router...the Telus...upstream on your network, Bridge Mode is indicated as the correct setting for all other routers on the network.
    If you can replace the Telus gateway with a simple modem (that performs no routing functions), you should be able to configure either the Time Capsule or the AirPort Extreme....whichever is connected to the modem....to provide a Guest Network.

  • 1300 Series Access Point/Bridge Power Injector - Using power over ethernet

    Can I use power over ethernet to supply the Injector with power?

    Hi Mikael,
    Sorry, this will not work. Have a look at these specs;
    1300 Series Power
    Power
    The access point/bridge receives inline power from the Cisco Aironet Power Injector (hereafter called the power injector). Dual-coax cables are used to provide Ethernet data and power from the power injector to the access point/bridge. The power injector is an external unit designed for operation in a sheltered environment, such as inside a building or vehicle. The power injector also functions as an Ethernet repeater by connecting to a Category 5 LAN backbone and using the dual-coax cable interface to the access point/bridge.
    The power injector is available in two models:
    Cisco Aironet Power Injector LR2 standard version (included with the access point/bridge)
    48-VDC input power
    Uses the 48-VDC power module (included with the access point/bridge)
    Cisco Aironet Power Injector LR2T optional transportation version
    12- to 40-VDC input power
    Note The power injector and the power module must not be placed in an outdoor unprotected environment. The power module must not be placed in a building's environmental air space, such as above a suspended ceiling.
    http://www.cisco.com/en/US/products/ps5861/products_installation_guide_chapter09186a008079b93b.html#wp1051840
    Dual coaxial cable to run from the power injector to the 1300. See attached notes:
    Cisco Aironet 1300 Series
    Cisco Aironet 1300 Series Access Point/Bridge Power Injector
    The Cisco Aironet 1300 Series Outdoor Access Point/Bridge Power Injector,converts the standard 10/100 BaseT Ethernet interface that is suitable for weather protected areas to a dual F-Type connector interface for coax cables that are more suitable for harsh outdoor environments. The Power Injector also provides power to the outdoor unit over the same cables with a power discover feature and surge protection. To support longer cable runs from your wireless network switch or router, the Power Injector LR is designed to accommodate up to a 100 meter coaxial cable run plus 100 meters of indoor cat5 cable?enabling total cable runs up to 200 meters. The Cisco Aironet 1300 Series Outdoor Access Point/Bridge ships with the Power Injector LR2 and an AC power supply.
    From this link:
    http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a008022551d.html
    Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide
    Ethernet Ports
    The access point/bridge dual-coax Ethernet ports consists of a pair of 75-ohm F-type connectors, linking the unit to your 100BASE-T Ethernet LAN through the power injector. The dual-coax cables are used to send and receive Ethernet data and to supply inline 48-VDC power from the power injector to the access point/bridge.
    From this link:
    http://www.cisco.com/en/US/products/ps5861/products_installation_guide_book09186a00804d3095.html
    AIR-PWRINJ-BLR2
    F-Type Connectors
    Dual coaxial cable carries full-duplex Ethernet, DC power, and full-duplex console port (RS-232 connection)
    From this link:
    http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a00802252e1.html
    Hope this helps!
    Rob

  • Configuring N channel on cisco 1252 Access Point

    Hi,
    Can someone help me for configuring N-Series band on Cisco 1252 Access Point in IOS Mode.
    Thanks
    Tabrez

    Firstly you need to use WPA2/AES or OPEN authentication.
    Cisco 802.11n Design and Deployment Guidelines
    http://www.cisco.com/en/US/solutions/collateral/ns340/ns394/ns348/ns767/white_paper_80211n_design_and_deployment_guidelines.html

  • Access Point Bridge Configuration

    I have two 1262N access points with 5Ghz antennas, and I have configured one of them as a root bridge and the other as a non-root bridge; both using the same ssid.  I have enble both dott11Radio interfaces on each access point.  The problem I am having is that they do not associate.  I have not configured them for any encryption or security.  I just want to make sure the connect before I add any other configuration.  Is there anything else that I need to configure to make them associate.

    Wrong forum, post in "wireless". You can move your post using the actions panel on the right.

  • Can an Aironet WiFi Access Point bridge multiple internal VLANs?

    I have Cisco Aironet 2700e access points.  Historically they were configured with a single SSID on both radios with WEP 128bit security.
    I now need to add new WiFi devices to the network that have limited flexibility.  They must be associated only with a specific radio (2.4ghz or 5ghz) and WPA2PSK security.
    My thought was to create two additional SSIDs on the 2700 access points, one for 2.4gz WPA2PSK and the other for 5ghz WPA2PSK.  The pre-existing SSID will continue to use 128bit WEP.  To do that  I need to use VLANs on the 2700e.
    I have no other VLANS on my network.  I only need VLANs on the 2700e because I have different physical devices that support different WiFi frequencies and security options.  I don't need to segment the network.
    How do I bridge the VLANs on the 2700e?
    Devices that connect to the non-native VLANs appear to be isolated from the rest of the network (as I would suspect with VLANs).  But that's not what I want .  I'm only using VLANs because I need multiple SSIDs, and I need multiple SSIDs because I have different physical devices that want different WiFI access point configurations.  I can't seem to find any way to configure the 2700e to bridge the VLANs for the multiple SSIDs.
    Any guidance would be appreciated.  I could buy additional access points but that seems to be defeating the purpose of having a device like the 2700e.
    Any help would be appreciated.
    Thank you.

    I made these changes to the example here:
    https://supportforums.cisco.com/document/55561/multiple-ssid-multiple-vlans-configuration-example-cisco-aironet-aps
    and it seems to be working.  (By "working" I mean that I can now ping to/from devices connected on different SSIDs.) I had to make these changes from the CLI.  There does not seem to be a way to make these changes from the GUI.  Is that correct? If there is a way to make these changes from the GUI please let me know.
    The changes I made were to make the sub interface for Dot11 radio 0 on the VLANs part of bridge-group 1.  So assuming the config in the example:
    ap(config)#interface Dot11Radio0.2
    ap(config-subif)#no bridge-group 2
    ap(config-subif)#bridge-group 1
    ap(config-subif)#exit
    ap(config)#interface Dot11Radio0.3
    ap(config-subif)#no bridge-group 3
    ap(config-subif)#bridge-group 1
    ap(config-subif)#exit
    I did not change the bridge group on the Ethernet interface.
    Questions:
    1. Did I create any new problems making this change? It seems to work, but am I going to get myself in trouble somewhere else?  Intuitively it makes sense to me: the VLANs are now part of the same bridge group (1, the native VLAN).  So all traffic should be bridged together.  Correct?
    2. I didn't change the Ethernet sub interfaces.  I don't seem to need to make that change.  I also don't like things sitting out there that I don't understand.  Should I do anything to clean up the Ethernet interfaces?
    3. The original configuration was made entirely from the GUI.  This change needs to be made from the CLI.  Can it be done from the GUI?  I can't seem to find a way to change bridge groups for a sub interface from the GUI. It worried me that it can't be done from the GUI.
    Thank you.
    Larry

  • PoE auto switchover with Cisco 1252 Access Point.

    Dear All
    I have a network for Managed Wireless using Cisco. This is a new network for me.
    I am in problem with Cisco Access Point 1252. My AP's are connected to a PoE Switch. And Cisco AP's are also connected Powered with also Power Adapter with UPS backup.
    But problem is if I disconnect power source of AP Power Adapter , AP is not getting up with PoE. PoE is up only when POWER PLUG of AP ADAPTER is physically pulled out from Socket.
    Question is if it is possible to make automatic Failover by PoE when Power source of AP ADAPTER is down ?? I mean no need to PULL OUT  POWER PLUG of AP ADAPTER.
    Waiting for your rely.
    It is very urgent .
    Thanking You
    Subrun.

    Hi Suburn,
    1- yes it is possible to do failover without unlupping the cable of AC adapter. When power on ACS adapter is off, then the faiolver happens.
    2- with regards to POE, if your switch supporting enhanced POE?
    Powering the Aironet 1250 Series Access Point with Cisco Enhanced PoE
    Cisco  Enhanced PoE was designed for customers who want to install new  PoE-enabled technologies that require greater than 15.4W per port to  function at full capability, such as wireless technology based on the  IEEE 802.11n standard. Cisco Enhanced PoE provides the full power  requirements for dual-radio modules and eliminates the need to run an  additional cabling drop or insert a separate power injector. Support for  Enhanced PoE is currently available on a variety of Cisco Catalyst® switching platforms. For more information on Enhanced PoE, visit http://www.cisco.com/en/US/prod/switches/epoe.html.
    Serge

  • E4200 as a Access Point/Bridge Mode

    I have spent most of the weekend trying to get this router to act as a proper Access Point.
    Has any got this to work correctly?
    When it does work (Stay connected) speeds and latency are rotten. If I go back to Routing Mode this thing kicks butt, but I isolate all devices attached to a different subnet and trying to set up proper routes has proved imposable.
    Firmware 1.0.2 r 13
    The online help stated to connect to the "internet interface" when in Bridge Mode DHCP Server Is not broadcasting to on the wireless or wired interfaces.
    If I used the wired interface as the uplink I can broadcast the DHCP to any device on wired but again nothing to the Wireless.
    When I "Show Routing Table" I see two static routes pointing to the ATT router for the Wired/Wireless Interfaces.....
    0.0.0.0 255.255.255.0 (my Gateway) Wired/Wireless
    (my Gateway) 255.255.255.0 0.0.0. Wired/Wireless
    Why?? 
    AP mode should only be working in Broadcast.
    By connecting the Wired Interfaces alone up to my switched network should not use the router at all.
    If you force all traffic to my router all traffic has to be inspected by the firewall
    You create a bottleneck my router interface is 10/100.
    ATT 2 Wire Gateway/Router with pinholes. 10/100/1000 Non managed 24 port Switch Network. Server infrastructure serving DNS/DHCP.
    I decided to buy this after reading it offered Bridge/Access Point mode instead of getting the WAP610 because I wanted to have the option to change to routing mode or AP mode.
    Since my ATT Uverse Router Wireless is “g” it takes forever to transfer files to and from my servers.

    OK If this helps... I am running a SOHO
    2Wire DSL Router with DHCP Off  Assigned 192.168.100.1 as the Router Gateway IP. NAT Enabled All firewall is being handled via 2Wire. Currently 2Wire WiFi is disabled. For the Linksys E4200
    2wire 10/100 interface up-linked into my d-link 24 port 10/100/1000 Layer 2 unmanaged switch.
    DHCP and DNS Servers on d-link switch
    VOIP on d-link switch
    Testing Results WAN Interface Bridge
    E4200 up-linked via 10/100/1000 Internet Interface to d-link network switch.
    E4200 Internet Interface DHCP assigned using MAC Reserved DHCP 192.168.100.22.
    E4200 in Bridge Mode
    Devices connected to 4X E4200 Gig Ports do not receive DHCP broadcast IP Address
    Device Connected to E4200 WiFi do not receive DHCP BroadcastIP Address
    Assign Static IP to my laptop WiFi in the 192.168.100.X range will establish communication but HUGE latency and poor speeds for any traffic internet or internally to any of my servers.
    At times the connection gets lost.
    In this configuration I get the above stated Route Tables.
    If this is layer 2 compliant it should be handing all local subnet traffic via MAC instead of routing.
    I have not taken the time to attempt to reconfigure my 2Wire to go into DMZ Plus mode and allow the linksys to handle all routing,  but from previous attempt with my wrt54 it did not go well. I accepted the slow 2Wire WiFi speeds.
    It is now getting to the point I am looking for better WiFi to local LAN speeds , I also am looking to do Layer 2 and bypass Routing if I can.
    The WAP160 has a 10/100 interface. I prefer gig

  • 1130AG Access Point PoE Problem with Cat 3750G-24PS-E switch

    I am having a problem on the PoE negotiation of Catalyst 3750G-24PS-E and 1130AG Access point. I used straight and cross cable for physical connection since by default the auto mdix per port of the switch is enabled/on. I used CLI, CNA and Web Device Manager on both devices to isolate and troubleshoot the problem but still the PoE negotiation on both devices won't work out. But when I used the access point into other switch (CE500 PoE Switch), the access point is working properly. Does anyone can help me to distinguish what the problem really is? The IOS Version of 3750G switch is 12.2(25) SEE2 and the 1130AG access point IOS Version is 12.3(8)JEA.

    Hi Rob,
    Thanks for your reply. Yes, I tried shut/no shut on the switchport many times. I saw that the switch grant power inline on the port but the port still can't/won't provide any power to boot up the access point.
    Thanks,
    Nelmar

  • Do I need a router or access point / bridge?

    Hi.  We have a MS small bus server with a software firewall.  It does dhcp and routes traffic so we don't need the router part of the router.
    Wireless  N access is needed.  Will a DAP 1522 (Wireless N access point / switch) offer the same wireless performance as a Linksys wireless N router?
    I just bought the DAP access point and am getting 100-130 mb/s with a strong signal.  Would the router work better with its giant antennae?
    Nick

    DAP 1522 is a good acess point. It  lets you connect up to 4 Ethernet-enabled devices such as set top boxes, game consoles, or computers to an existing Wi-Fi network for on-demand broadcast, online gaming, or media streaming throughout the home.
    With dual-band wireless capabilities, the DAP-1522 is ideal for wireless HD video streaming and gaming applications because entertainment content can be sent over the less crowded 5GHz band.
    The DAP-1522 can also be used to create a new 802.11n wireless network using its Access Point feature. Simply connect it to an existing wired or wireless router, and you'll enjoy greater range and data speeds in seconds.

  • MSI Access point AP54G problems!How to ....?

    Hello to all of you dear MSI users! I've got MSI AP54G and i got a problem! I've just unpacket this thing before two days and till now I can not acces it's setup trough it's IP adress? Why I don't know! I 've worked before for a while with Canyon Accses point and it worked prefektly trought it's IP setup program. Now the default IP adress of my MSI AP is 192.168.1.254 and when I'm trying to get to it I allways get this web adres of some kind of strange web firm.(try your self). I switched of the internet conection but then I got a wrong masage! The other strange  in this produkt is the MSIA AP manager program. it tells me that there si AP conected to the PC but i sai evry time when I try to conect withh th AP this "The target AP is not in the same networksegment segment, so you canot conect it!" What? What's that? And by the way the dammed thing is cinected with my neighbour, giving him prefekt internet and sharing to him my files without problem! OK! But in our beatiful neighbourhood there are many wirelles machines! And how can somebody from MSI team tellme how  to  prevent them coming to my network when I can't even  open this stupid  web setup program!
    Best regards to all of you! I hope somebody got the answer!.Thanks!
    User:Panzer  from Bulgaria!

    I found that I'm not reading enought good the manual! Thanks! Al of you peaople sorry for the interuption!

  • Power settings for a 1142/1252 access point

    What power setting should I use if I need to limit the max power of a
    1142 or 1252 to 20mW (802.11g).  I also need to limit power at another site
    to 10mW can any one tell me what that setting would be?
    Thanks for the help

    Steve, i wonder if the commands would still work, after all its IOS.
    JW did you try the below command ? I dont have a autonmous ap in front of me. Also when you say "its an autonmous right now". What do you mean by that ... What will it end up being MESH, CAPWAP, what ?
    bridge# show environment
    Environmental Statistics
    Environmental status as of 00:10:45 UTC Thu Mar 27 2003
    Data is 3 second(s) old, refresh in 57 second(s)
    Dot11Radio0 temperature measured at 37(C)

  • Cisco 1252 Access Point Read Write Account

    HI
    i sent out a Cisco 1252 AP to one of my sites and i removed the default cisco account from the device before i shipped it and now when i try to get into
    it i can't .I can get logged in through telnet and it's working fine but i just can't get into the web interface. is there a way to re add the cisco account through command line so that i can log into it.
    Thanks in advance

    I tried that and it still dosen't work, do you think that i will need to just send them another AP fresh out the box with the account in it.

  • Similar SSID for two 1252 access points

    Hi, we currently have one 1252 AP. It has two Vlans. One for data and one for voice. Just bought another 1252 AP and going to have similar setup.
    I read I can have similar SSID so that uses don't need to re-authenticate to the other AP. If this is true, can I just copy the config.txt file to the other AP, except of course I'll change the static IP addr of the AP. Pls advise, thks.

    Hi sohocisco,
    Keeping the same SSID/VLAN will ensure that L2 roaming is possible, which is what you want. Depending on your authentication methods, though, you may need to configure WDS in order to ensure for seamless roaming as you describe.
    Note that this is only if you're using and EAP or WPA (non-PSK) authentication method. Please see this document for configuration assistance:
    http://www.cisco.com/en/US/docs/wireless/access_point/12.3_7_JA/configuration/guide/s37roamg.html
    I hope that helps!
    Jeff

  • Bridge to bridge and bridge to access-point via wireless is it possible.

    here;s my topology i am trying to configure. i have a router whose ethernet is connected to a bridge.this bridge 1 is connected to a bridge 2 via wireless. now i am trying to connect a access-point via wireless to this bridge2. is it possible for bridge 2 to support connectivity to the bridge1 and the access-point both of them via wireless.
    can someone pls help me on this.
    waiting for someone to reply.
    regards
    sebastan

    You can set up each radio in the access point for different functionality. Considering the scenario, this can be done by setting up the SSID for the G radio and another SSID for the A radio. Then, set the role in the radio network parameter for the G radio to access point and for the A radio to the root bridge role.
    ou can prevent unauthorized users from reconfiguring your access point/bridge and viewing configuration information. Typically, you want network administrators to have access to the access point/bridge while you restrict access to users who connect through a terminal or workstation from within the local network.
    To prevent unauthorized access to your access point/bridge, you should configure one of these security features:
    Username and password pairs, which are locally stored on the access point/bridge. These pairs authenticate each user before that user can access the access point/bridge. You can also assign a specific privilege level (read only or read/write) to each username and password pair.
    http://www.cisco.com/en/US/products/ps5861/products_configuration_guide_chapter09186a00804ed6d4.html

Maybe you are looking for

  • Link for Adobe Premiere Elements 11 will not work. Any help please?

    I bought my Premiere Elements package from another seller which gave me a link to download from Adobe. The product key thing is legit but every time I click on the file link for windows, my laptop comes up with this message: "The file archive of Adob

  • Macbook Pro and NVIDIA GeForce 320M HDCP Compliance

    Anyone know if the NVIDIA card is HDCP compliant? I want to purchase an external blu-ray burner for my laptop but want to make sure it will work first. I have found limited tech specs on this card on-line. D

  • Regarding packages

    Hi guys what is the difference of is/as keyword in package body declaration.....

  • Passive server database still failed and suspended after seeding

    Hi, I have a 2 exchange 2013 servers in windows 2012 OS both servers are configured with DAG one is active and the other one is passive I moved the 5 databases in other drive and it was successful but no matter what I try one of my database in passiv

  • GTK2 apps crashing left & right

    Hello, all-- This has got me tearing my hair. Lately I've been having GTK2 apps crash in response to very normal actions. The problem seems to be related to libgnomevfs and/or libxml2, but I have no idea what exactly might be wrong. I've tried google