1252 LAP won't join WLC
Hi all
I'm having an issue with a 1252 LAP that is connected to the WLC over a WAN link.
Basically, it won't associate. The following is taken from a console into the LAP:
*Mar 1 00:00:07.799: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:08.799: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:26.851: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:27.003: Logging LWAPP message to 255.255.255.255.
%CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
%CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
%DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 10.148.x.x, mask 255.255.255.0, hostname AP002
2.90a3.533a
Translating "CISCO-LWAPP-CONTROLLER.nation.radix"...domain server (10.x.x.x)
%LWAPP-3-CLIENTEVENTLOG: Controller address 10.x.x.x obtained through DHCP
%LWAPP-3-CLIENTEVENTLOG: Did not get log server settings from DHCP.
%SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
%LWAPP-3-CLIENTEVENTLOG: Performing DNS resolution for CISCO-LWAPP-CONTROLLER.nation.radix
%LWAPP-3-CLIENTERRORLOG: DNS Name Lookup: could not resolve CISCO-LWAPP-CONTROLLER.nation.radix
%LWAPP-5-CHANGED: LWAPP changed state to JOIN
%LWAPP-3-CLIENTERRORLOG: Join Timer: did not recieve join response (controller - Fxxxxxxx)
%LWAPP-3-CLIENTERRORLOG: Set Transport Address: no more AP manager IP addresses remain
%SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: DID NOT GET JOIN RESPONSE.
%LWAPP-5-CHANGED: LWAPP changed state to DOWN
IOS Bootloader - Starting system.
Xmodem file system is available.
The ap-manager interface is configured correctly and there isn't a duplicate IP address.
The LAP was initially stand alone and was converted to LWAPP.
The MTU over the WAN link is 1500 bytes.
All I'm getting from the WLC debugs is:
Mon Jul 20 11:42:59 2009: 00:22:xx:xx:xx:xx Received LWAPP DISCOVERY REQUEST from AP 00:22:xx:xx:xx:xx to 00:19:xx:xx:xx:xx on port '29'
Mon Jul 20 11:42:59 2009: 00:22:xx:xx:xx:xx LWAPP Discovery Request AP Software Version: 0x3003300
Mon Jul 20 11:42:59 2009: 00:22:xx:xx:xx:xx Successful transmission of LWAPP Discovery Response to AP 00:22:xx:xx:xx:xx on port 29
So basically the join messages don't seem to reach the WLC. In fact they don't even seem to reach the local router on the remote subnet. The discovery packets are seen on the local router but the joins don't seem to appear at all.
I'm not sure if it's a latency issue. Average latency over the WAN link is under 70ms.
I'm assuming the certificate on the WAP is MIC and the MAC details have been entered into the WLC AP Security policies for authentication. I'm not seeing any debugging messages relating to bad authentication at all.
I can't debug from the LAP as it's LWAPP, obviously.
I've been through many Cisco documents trying to troubleshoot the problem, including this http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a00808f8599.shtml, but can't find a solution.
We're running WLC version 4.2.130.0.
Can anyone help?
Thanks
Brodie
I assume you have connected to router's AUX and doing reverse telnet. You should be getting Password: prompt on your LAP's console. Password and Enable are both Cisco. Below is console output from my lab's 1250 LAP after erasing configuration (which can only be initiated from controller). In my case, the vlan is not configured with Option 43 and no proper DNS, so LAP doesn't join the controller.
By the way, your best bet might be to convert this LAP back to IOS and then back to LAP again. Use this method:
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
Do you have "Authorize APs against AAA" checked under Security > AP Policies in any of your WLCs ?
Press RETURN to get started!
*Mar 1 00:00:07.099: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:07.619: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:08.595: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*May 10 23:17:25.199: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*May 10 23:17:26.155: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1250 Software (C1250-K9W8-M), Version 12.4(10b)JDC, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Fri 01-May-09 10:49 by prod_rel_team
*May 10 23:17:26.155: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
*May 10 23:17:27.183: %SSH-5-ENABLED: SSH 2.0 has been enabled
*May 10 23:17:27.387: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*May 10 23:17:27.387: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*May 10 23:17:28.439: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*May 10 23:17:28.439: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*May 10 23:17:30.783: %LWAPP-3-CLIENTERRORLOG: ../lwapp/lwapp_l2.c:152 - discarding msg type 12 in state 0
*May 10 23:17:30.783: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*May 10 23:17:30.795: %DOT11-6-FREQ_SCAN: Interface Dot11Radio0, Scanning frequencies for 16 seconds
*May 10 23:17:44.571: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*May 10 23:17:44.731: Logging LWAPP message to 255.255.255.255.
%LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
%LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
%LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
%SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
%LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
%LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
%LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
%LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
%LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
%DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 172.16.8.3, mask 255.255.255.0, hostname AP0022.558e.24bc
User Access Verification
Password:
AP0022.558e.24bc>en
Password:
AP0022.558e.24bc#show lwapp ?
client LWAPP Client Information
ids LWAPP IDS Information
ip LWAPP IP configuration
mcast LWAPP Mcast Information
reap LWAPP REAP Information
rm LWAPP RM Information
AP0022.558e.24bc#show lwapp client config
AP0022.558e.24bc#
AP0022.558e.24bc#ping 3.45.47.143
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 3.45.47.143, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms
AP0022.558e.24bc#
Similar Messages
-
LAP 1240 won't join WLC across subnets
I am having a problem getting LAPs that are in other subnets to join our WLC. If I take the LAP and place it on the same VLAN/subnet as the WLC, it joins as expected. If I move it to another subnet, I get the following:
*Mar 1 00:00:13.065: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1200 Software (C1200-K9W8-M), Version 12.4(13d)JA, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Fri 08-Feb-08 17:24 by prod_rel_team
*Mar 1 00:00:13.119: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:13.519: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:14.519: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:14.536: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:14.545: %DOT11-6-FREQ_SCAN: Interface Dot11Radio0, Scanning frequencies for 24 seconds
*Mar 1 00:00:15.536: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:28.133: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:28.171: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:28.177: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:28.192: SSC Load Current Size crypto_mykey 120, offset 9389, Saved Size soap_cert_crypto_mykey 124
*Mar 1 00:00:28.390: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:28.892: Logging LWAPP message to 255.255.255.255.
%LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
%SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
%LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
%LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
%LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
%LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
%DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 192.168.115.75, mask 255.255.255.192, hostname AP0013.c3a7.bf97
Translating "CISCO-LWAPP-CONTROLLER.mydomain.here"...domain server (X.X.X.X) [OK]
%LWAPP-3-CLIENTEVENTLOG: Did not get vendor specific options from DHCP.
%LWAPP-3-CLIENTEVENTLOG: Did not get log server settings from DHCP.
%LWAPP-3-CLIENTEVENTLOG: Performing DNS resolution for CISCO-LWAPP-CONTROLLER.mydomain.here
%LWAPP-3-CLIENTEVENTLOG: Controller address Y.Y.Y.Y obtained through DNS
%LWAPP-5-CHANGED: LWAPP changed state to JOIN
%LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
%LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
%LWAPP-3-CLIENTERRORLOG: Join Timer: did not recieve join response (controller - 2169-WLC4402-1)
%LWAPP-3-CLIENTERRORLOG: Set Transport Address: no more AP manager IP addresses remain
%SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: DID NOT GET JOIN RESPONSE.
%LWAPP-5-CHANGED: LWAPP changed state to DOWN
I have checked the WLC for any messages that look like crypto or other problems, but I don't see anything that stands out. Any suggestions or pointers would be greatfully accepted.%LWAPP-3-CLIENTERRORLOG: Set Transport Address: no more AP manager IP addresses remain
Can you provide more information such as:
1. How many APs can the WLC4402 support and how many are currently joined?
2. What is your WLC's firmware?
3. Is there a possibility of a duplicate IP address in your network?
Troubleshoot a Lightweight Access Point Not Joining a Wireless LAN Controller
http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a00808f8599.shtml -
1310 LAP unable to join WLC 5508
Hi All,
Hope to you a very happy new year,
I have an (AIR-LAP1310G-E-K9R) and I tried to join it to WLC 5508 but I'm facing an error,
I get this error from the LAP 1310 console as below:
Compiled Mon 17-Jul-06 11:45 by alnguyen
*Mar 1 00:00:05.289: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:06.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:23.337: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:33.477: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.114.36.25, mask 255.255.255.0, hostname APe4d3.f1c2.8882
examining image...
*Mar 1 00:00:44.781: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
*Jan 11 15:21:37.178: %LWAPP-5-CHANGED: LWAPP changed state to IMAGE
%Error opening (Protocol error)archive download: takes 6 seconds
*Jan 11 15:21:43.178: LWAPP_CLIENT_ERROR_DEBUG: Retransmission count for packet exceeded more than max(IMAGE_DATA
, 1)
*Jan 11 15:21:43.178: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Jan 11 15:21:43.179: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Jan 11 15:21:43.181: LWAPP_CLIENT_ERROR: not receive read response(3)
*Jan 11 15:21:43.185: lwapp_image_proc: unable to open tar file
*Jan 11 15:21:43.200: %SYS-5-RELOAD: Reload requested by lwapp image download proc. Reload Reason: Reason unspecified.
*Jan 11 15:21:43.201: %LWAPP-5-CHANGED: LWAPP changed state to DOWN
*Jan 11 15:21:43.207: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERYXmodem file system is available.
flashfs[0]: 3 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 7741440
flashfs[0]: Bytes used: 1861632
flashfs[0]: Bytes available: 5879808
flashfs[0]: flashfs fsck took 14 seconds.
Base ethernet MAC Address: e4:d3:f1:c2:88:82
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
Loading "flash:/c1310-rcvk9w8-mx/c1310-rcvk9w8-mx"...#######################################################################################################################################################################
File "flash:/c1310-rcvk9w8-mx/c1310-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1310 Software (C1310-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:45 by alnguyen
Image text-base: 0x00003000, data-base: 0x00359EA0
Initializing flashfs...
flashfs[1]: 3 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 7741440
flashfs[1]: Bytes used: 1861632
flashfs[1]: Bytes available: 5879808
flashfs[1]: flashfs fsck took 2 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
cisco AIR-LAP1310G-E-K9R (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
Processor board ID FGL1649T00U
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from reload
LWAPP image version 3.0.51.0
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: E4:D3:F1:C2:88:82
Part Number : 73-8960-09
PCA Assembly Number : 800-24963-06
PCA Revision Number : B0
PCB Serial Number : FOC16447J1K
Top Assembly Part Number : 800-28479-05
Top Assembly Serial Number : FGL1649T00U
Top Revision Number : D0
Product/Model Number : AIR-LAP1310G-E-K9R
Press RETURN to get started!
*Mar 1 00:00:04.329: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1310 Software (C1310-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:45 by alnguyen
*Mar 1 00:00:05.289: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:06.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:23.337: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:33.352: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.114.36.28, mask 255.255.255.0, hostname APe4d3.f1c2.8882
examining image...
*Mar 1 00:00:44.783: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
*Jan 11 15:21:37.189: %LWAPP-5-CHANGED: LWAPP changed state to IMAGE
%Error opening (Protocol error)archive download: takes 6 seconds
*Jan 11 15:21:43.189: LWAPP_CLIENT_ERROR_DEBUG: Retransmission count for packet exceeded more than max(IMAGE_DATA
, 1)
*Jan 11 15:21:43.189: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Jan 11 15:21:43.189: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Jan 11 15:21:43.192: LWAPP_CLIENT_ERROR: not receive read response(3)
*Jan 11 15:21:43.195: lwapp_image_proc: unable to open tar file
*Jan 11 15:21:43.210: %SYS-5-RELOAD: Reload requested by lwapp image download proc. Reload Reason: Reason unspecified.
*Jan 11 15:21:43.210: %LWAPP-5-CHANGED: LWAPP changed state to DOWN
*Jan 11 15:21:43.216: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERYXmodem file system is available.
flashfs[0]: 3 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 7741440
flashfs[0]: Bytes used: 1861632
flashfs[0]: Bytes available: 5879808
flashfs[0]: flashfs fsck took 14 seconds.
Base ethernet MAC Address: e4:d3:f1:c2:88:82
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
Please Advise,
Thanks in advanced,
Ahmed,Dear Stefan,
Many thanks for your kind reply,
Please find the information below:
Controller Summary
Management IP Address
10.114.44.131
Service Port IP Address
10.114.23.20
Software Version
7.2.111.3
Field Recovery Image Version
6.0.182.0
System Name
CIR906.WLC.5508
Please Advise,
Thanks,
Ahmed, -
I am deploying WLC 4402 with LWAP 1131 but AP fail to join the WLC .The resone that I dont have DNS server.The error message in the AP is :
AP001d.451f.8582>
*Mar 1 00:00:38.005: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned D
HCP address 172.26.5.12, mask 255.255.255.0, hostname AP001d.451f.8582
Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:49.371: LWAPP_CLIENT_ERROR: lwapp_name_lookup - Could Not resolve
I tried to configure the Controller address in LAP but I fail ,The error when I tried to configure AP is below:
AP001d.451f.8582#lwapp ap controller ip address 172.26.5.10
ERROR!!! Command is disabled.
my question is :
is it possible to make LAP join WLC with out DNS,if yes how ?Hi Yhab,
There are other ways besides DNS to help in the AP and WLC Discovery process. Have a look in this good doc;
Lightweight AP (LAP) Registration to a Wireless LAN Controller (WLC)
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a00806c9e51.shtml#topic2
For the Static entry problem;
If this AP was ever registered you can use this command from the LAP CLI to clear the LWAPP configuration on the LAP:
clear lwapp private-config
This allows you to use the AP LWAPP static configuration commands again.
Here is an example:
Enable (enter password)
AP1240#clear lwapp private-config
AP1240#lwapp ap hostname AP1240
AP1240#lwapp ap ip address 10.77.244.199 255.255.255.224
AP1240#lwapp ap ip default-gateway 10.77.244.220
AP1240#lwapp ap controller ip address 172.16.1.50
Note: You cannot use the clear lwapp private-config command when the LAP is registered with the controller.
http://www.cisco.com/en/US/products/hw/wireless/ps430/products_tech_note09186a00808e2d27.shtml#t2
Hope this helps!
Rob -
Hi,
I have a 1142N which does not join the WLC when connected via a 2960 switch. When I connect a different lap 1142N to the same port on the same switch using the same cables, it does join the lap to the WLC. And when I connect the first lap directly to the WLC it also works fine.
Resetting the failing lap does not fix the problem. All software levels on the lap are the same.
Anyone an idea what could be wrong?
Thanks in advance.
Regards
Jeroenthnx for your support so far.
All the AP's are the same, AIR-LAP1142N-E-K9 v05. I have two AP's which work fine when connected via the 2960 therefore I assume that the switch, wlc, vlan and dhcp configuration is fine.The thirth one is giving me some challenges ;-)
Note: the non working AP is only not working when connected via de 2960, it is working fine when directly connected to the WLC2106.
@David, where can i find the regulatory domain setting?
working AP
NAME: "AP1140", DESCR: "Cisco Aironet 1140 Series (IEEE 802.11n) Access Point"
PID: AIR-LAP1142N-E-K9
failing AP
NAME: "AP1140", DESCR: "Cisco Aironet 1140 Series (IEEE 802.11n) Access Point"
PID: AIR-LAP1142N-E-K9
AP manager subnet
192.168.1.0/24
Management subnet
192.168.2.0/24
WLC2106 sysinfo
==================================================================================
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.220.0
RTOS Version..................................... 7.0.220.0
Bootloader Version............................... 4.0.191.0
Emergency Image Version.......................... 6.0.199.4
Build Type....................................... DATA + WPS
System Name...................................... CiscoWLC1
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.828
IP Address....................................... 192.168.2.2
System Up Time................................... 10 days 0 hrs 31 mins 36 secs
System Timezone Location.........................
Configured Country............................... NL - Netherlands
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +48 C
--More-- or (q)uit
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 2
Number of Active Clients......................... 0
Burned-in MAC Address............................ 70:81:05:AE:F9:C0
Maximum number of APs supported.................. 6
DHCP pool configured on core switch
==================================================================================
ip dhcp pool AP-Pool
network 192.168.1.0 255.255.255.0
default-router 192.168.1.254
dns-server 192.168.1.1
Boot info failing WAP
==================================================================================
using eeprom values
WRDTR,CLKTR: 0x85000800 0x40000000
RQDC ,RFDC : 0x80000037 0x0000020f
using ÿÿÿÿ ddr static values from serial eeprom
ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x85000800, 0x40000000
RQDC, RFDC : 0x80000037, 0x0000020f
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is up.
PCIE1: VC0 is active
PCIEx: initialization done
flashfs[0]: 28 files, 8 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
% Please define a domain-name first.
Press RETURN to get started!
*Mar 1 00:00:08.197: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:08.208: *** CRASH_LOG = YES
Security Core found.
Base Ethernet MAC address: 64:9E:F3:B3:5F:88
*Mar 1 00:00:09.787: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:10.359: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:10.393: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 215 messages)
*Mar 1 00:00:10.416: status of voice_diag_test from WLC is false
*Mar 1 00:00:11.459: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:12.536: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:12.573: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1140 Software (C1140-K9W8-M), Version 12.4(23c)JA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Tue 18-Oct-11 14:52 by prod_rel_team
*Mar 1 00:00:12.573: %SNMP-5-COLDSTART: SNMP agent on host AP649e.f3b3.5f88 is undergoing a cold start
*Mar 1 00:11:43.044: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:11:43.105: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:11:43.105: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:11:44.106: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:11:44.106: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:11:44.297: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:11:52.102: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 192.168.1.44, mask 255.255.255.0, hostname AP649e.f3b3.5f88
*Mar 1 00:12:01.917: status of voice_diag_test from WLC is false
*Mar 1 00:12:01.972: Logging LWAPP message to 255.255.255.255.
*Mar 1 00:12:04.769: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:12:04.792: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:12:04.816: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:12:05.776: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 00:12:05.776: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
*Mar 1 00:12:05.802: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (192.168.1.1)
*Mar 1 00:13:13.006: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
Not in Bound state.
*Mar 1 00:13:23.524: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Mar 1 00:13:23.637: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 192.168.1.45, mask 255.255.255.0, hostname AP649e.f3b3.5f88
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (192.168.1.1)
*Mar 1 00:14:19.511: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
Not in Bound state.
*Mar 1 00:14:30.030: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Mar 1 00:14:30.139: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 192.168.1.46, mask 255.255.255.0, hostname AP649e.f3b3.5f88
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (192.168.1.1)
*Mar 1 00:15:26.013: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
Not in Bound state.
*Mar 1 00:15:36.532: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Mar 1 00:15:36.640: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 192.168.1.47, mask 255.255.255.0, hostname AP649e.f3b3.5f88
Show version failing wap
==================================================================================
Cisco IOS Software, C1140 Software (C1140-K9W8-M), Version 12.4(23c)JA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Tue 18-Oct-11 14:52 by prod_rel_team
ROM: Bootstrap program is C1140 boot loader
BOOTLDR: C1140 Boot Loader (C1140-BOOT-M) Version 12.4(23c)JA3, RELEASE SOFTWARE (fc1)
uptime is 6 minutes
System returned to ROM by power-on
System image file is "flash:/c1140-k9w8-mx.124-23c.JA3/c1140-k9w8-mx.124-23c.JA3"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1142N-E-K9 (PowerPC405ex) processor (revision A0) with 98294K/32768K bytes of memory.
Processor board ID FCZ1548W0GJ
PowerPC405ex CPU at 586Mhz, revision number 0x147E
Last reset from power-on
LWAPP image version 7.0.220.0
1 Gigabit Ethernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 64:9E:F3:B3:5F:88
Part Number : 73-12836-03
PCA Assembly Number : 800-33767-03
PCA Revision Number : A0
PCB Serial Number : FOC15443W5A
Top Assembly Part Number : 800-33775-02
Top Assembly Serial Number : FCZ1548W0GJ
Top Revision Number : A0
Product/Model Number : AIR-LAP1142N-E-K9
Configuration register is 0xF
show inventory failing wap
==================================================================================
NAME: "AP1140", DESCR: "Cisco Aironet 1140 Series (IEEE 802.11n) Access Point"
PID: AIR-LAP1142N-E-K9
Message was edited by: Jeroen -
2x 1252s unable to fully join 2504
Hi everyone :)
And thank you for an awesome resource!
I was lucky enough to get my hands on this 2504 at work for labbing and had set the goal for last night to convert the two 1252s to lwap and join them with the controller. Just a simple ssid and thats it.
However imagin my frustration when i saw the access points register however with their radios turned off and no way of turning them back on. These are APs i've had running in autonomous mode for some time now so they work just fine.
Fortunately, and since the setup is just a lab for now, i had my console cable hooked to one of the aps so i could see the boot process running. What i have snipped in here below is a part of the console log from after AP01 booted. I googled for some time to figure this out and during my trouble shooting i toggled the dhcp client to reproduce the error message. Same thing, highlightet below, on both aps!
Just a note, during initial setup on the controller i checked both the US and DK for language / region selection. I found a case with the wrong regulartory domain between controller and ap with similar symptoms as highlightet below. I changed the setting to just DK and kept working, since the APs are ETSI regulatory.
What is the problem? And what can i do about it :)
Thanks in advance!
/Kim
<snip>
AP01#release dhcp bvi 1
AP01#renew dhcp bvi 1
Not in Bound state.
AP01#renew dhcp bvi 1
Not in Bound state.
AP01#
*Jan 13 23:43:41.451: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.30.18:5246
*Jan 13 23:43:41.555: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.30.119, mask 255.255.255.0, hostname AP01
renew dhcp bvi 1
AP01#
*Jan 13 23:43:44.295: %WIDS-6-DISABLED: IDS Signature is removed and disabled.
*Jan 13 23:43:44.295: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Jan 13 23:43:44.295: bsnInitRcbSlot: slot 0 has NO radio
*Jan 13 23:43:44.307: %CAPWAP-3-ERRORLOG: Binding Config Initialization failed for binding 1
*Jan 13 23:43:44.331: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Jan 13 23:43:45.339: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Jan 13 23:43:45.347: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Jan 13 23:43:46.367: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Jan 13 23:43:47.367: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
Translating "CISCO-LWAPP-CONTROLLER.mgmt.dk"...domain server (192.168.10.10)
*Jan 13 23:43:54.331: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Jan 13 23:43:54.331: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.mgmt.dk
*Jan 13 23:44:04.335: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan 13 23:43:54.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.30.18 peer_port: 5246
*Jan 13 23:43:54.423: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.30.18 peer_port: 5246
*Jan 13 23:43:54.423: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.30.18
*Jan 13 23:43:54.427: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Jan 13 23:43:54.427: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Jan 13 23:43:54.427: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Jan 13 23:43:54.427: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 192.168.30.18
*Jan 13 23:43:54.739: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Jan 13 23:43:55.015: %WIDS-6-ENABLED: IDS Signature is loaded and enabled
*Jan 13 23:43:55.739: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
AP01#
<snip>Hi again :)
Thanks for your reply Leo, I was about to 'sh' everything to you guys when the radio led on one of the APs suddently turned on! ;)
Actually, I upgraded the controller to v7.6.130.0. And then, reset the controller to factory defaults... Without checking if the upgrade had worked. After that woila.
So since this is a lab I will downgrade tonight to v7.6.120.0 to try and reproduce the error.
However there was one small detail that baffled me, when i set up the lab I added both US and DK to the language list. I unchecked US when troubleshooting the problem. Then before the upgrade I noticed a log message mentioning a problem with the regulatory domain on the joining AP. The message said something about changing the domain from () to (DK). From nothing to DK. Every time it rebooted...
Anyway, now it works. Thanks Scott and everyone else.
/Kim -
I have a new Macbook Pro. It can see, but won't join the open wireless networks that my existing Macbook Pro joins. What can I do, please?
Mac OS X 10.7 Help: Troubleshoot a network printer
-
Problem to join WLC (AP1131 && WISM)
Hello,
AP will not join WLC. Everytime, the AP try to join the WLC but...
CLI of AP :
May 18 08:02:51.194: status of voice_diag_test from WLC is false
May 18 08:02:51.194: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
May 18 08:02:51.195: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
May 18 08:02:51.196: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
May 18 08:02:51.201: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
May 18 08:02:51.227: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
May 18 08:03:01.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.23.2.243 peer_port: 5246
May 18 08:03:01.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
May 18 08:03:02.398: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.23.2.243 peer_port: 5246
May 18 08:03:02.400: %CAPWAP-5-SENDJOIN: sending Join Request to 172.23.2.243
May 18 08:03:02.400: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
May 18 08:03:07.399: %CAPWAP-5-SENDJOIN: sending Join Request to 172.23.2.243
May 18 08:03:07.400: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.23.2.243
May 18 08:03:07.400: %DTLS-5-PEER_DISCONNECT: Peer 172.23.2.243 has closed connection.
May 18 08:03:07.400: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.23.2.243:5246
May 18 08:03:07.459: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
May 18 08:03:07.459: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
May 18 08:03:07.525: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
May 18 08:03:07.525: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
May 18 08:03:07.526: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
May 18 08:03:07.556: status of voice_diag_test from WLC is false
May 18 08:03:18.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.23.2.243 peer_port: 5246
May 18 08:03:18.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
May 18 08:03:19.406: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.23.2.243 peer_port: 5246
May 18 08:03:19.408: %CAPWAP-5-SENDJOIN: sending Join Request to 172.23.2.243
May 18 08:03:19.408: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
May 18 08:03:24.406: %CAPWAP-5-SENDJOIN: sending Join Request to 172.23.2.243
May 18 08:03:24.408: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.23.2.243
May 18 08:03:24.408: %DTLS-5-PEER_DISCONNECT: Peer 172.23.2.243 has closed connection.
May 18 08:03:24.408: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.23.2.243:5246
May 18 08:03:24.467: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
May 18 08:03:24.467: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
May 18 08:03:24.533: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
May 18 08:03:24.533: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
If someone know how to resolve my problem ..
Thanks, Vincent A.Hello,
The firmware of the controlers is : 7.0.116.0
The AP run the firmware c1130-rcvk9w8-tar.124-21a.JA2.tar and the model is AP1131.
results of 'dir' command :
AP001d.a1ee.1cbc#dir
Directory of flash:/
2 -rwx 20380 May 18 2011 07:20:51 +00:00 event.log
185 drwx 128 May 17 2011 09:18:44 +00:00 c1130-rcvk9w8-mx
4 -rwx 7192 May 18 2011 09:03:13 +00:00 private-multiple-fs
5 -rwx 400 May 18 2011 07:26:15 +00:00 env_vars
7 -rwx 1919 May 17 2011 09:19:13 +00:00 private-config
10 drwx 320 May 18 2011 07:20:46 +00:00 c1130-k9w8-mx.124-23c.JA2
6 -rwx 0 May 18 2011 07:18:08 +00:00 validate.txt
15740928 bytes total (8032256 bytes free)
AP001d.a1ee.1cbc#
On the controllers i can see that, but i don't understand why :
*spamReceiveTask: May 18 11:05:20.375: 00:1e:13:6f:47:f0 Msg Type = 3 Capwap state = 0
*spamReceiveTask: May 18 11:05:20.375: 00:1e:13:6f:47:f0 Join Request from 172.22.4.96:57804
*spamReceiveTask: May 18 11:05:20.375: 00:1e:13:6f:47:f0 Join request received from AP which is already present. Deleting previous connection
172.22.4.96:57804
*spamReceiveTask: May 18 11:05:20.375: 00:1e:13:6f:47:f0 Multiple Join Request: Join request received from AP which is already present. Deleting previous conne
*spamReceiveTask: May 18 11:05:20.375: 00:1e:13:6f:47:f0 Finding DTLS connection to delete for AP (172:22:4:96/57804)
*spamReceiveTask: May 18 11:05:20.375: 00:1e:13:6f:47:f0 Disconnecting DTLS Capwap-Ctrl session 0x136c2550 for AP (172:22:4:96/57804)
*spamReceiveTask: May 18 11:05:20.375: 00:1e:13:6f:47:f0 CAPWAP State: Dtls tear down
*spamReceiveTask: May 18 11:05:20.376: 00:1e:13:6f:47:f0 DTLS connection 0x136c2550 closed by controller
*spamReceiveTask: May 18 11:05:20.377: 00:1e:13:6f:47:f0 Deleting and removing AP 00:1e:13:6f:47:f0 from fast path
*spamReceiveTask: May 18 11:05:20.377: 00:1e:13:6f:47:f0 DTLS connection not found. Ignoring join request from 172.22.4.96:57804
*spamReceiveTask: May 18 11:05:20.377: 00:1e:13:6f:47:f0 State machine handler: Failed to process msg type = 3 state = 0 from 172.22.4.96:57804
*spamReceiveTask: May 18 11:05:20.377: 00:1e:13:6f:47:f0 Failed to parse CAPWAP packet from 172.22.4.96:57804
*spamReceiveTask: May 18 11:05:20.377: CAPWAP DTLS connection closed msg
*spamReceiveTask: May 18 11:05:20.377: 00:1e:13:6f:47:f0 DTLS connection closed event receivedserver (172:23:2:243/52
Thanks, Vincent A. -
Why LAP1131AG and LAP11412 cannot to join WLC 2504?
I have WLC 2504, Cisco LAP1131AG and then Cisco LAP1142N. Why LAP1131AG and LAP11412 cannot to join WLC 2504?
this is error code at the Cisco LAP1131AG
*Sep 12 19:30:27.730: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Sep 12 19:30:27.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.100.10 peer_port: 5246
*Sep 12 19:30:57.001: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2051 Max retransmission count reached!
*Sep 12 19:31:27.000: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.100.10:5246
*Sep 12 19:31:32.083: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Sep 12 19:31:32.083: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Sep 12 19:31:32.085: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Sep 12 19:31:32.117: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Sep 12 19:31:32.118: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Sep 12 19:31:33.083: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Sep 12 19:31:33.112: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Sep 12 19:31:33.117: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Sep 12 19:31:34.104: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Sep 12 19:31:34.111: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Sep 12 19:31:34.142: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Sep 12 19:31:34.147: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Sep 12 19:31:34.152: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Sep 12 19:31:35.141: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Sep 12 19:31:35.146: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Sep 12 19:31:35.170: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Sep 12 19:31:36.171: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
this is version LAP1131AG
AP0018.18fc.fd58#sh version
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(25e)JAO6, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 22-Aug-14 10:07 by prod_rel_team
ROM: Bootstrap program is C1130 boot loader
BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(7)JA1, RELEASE SOFTWARE (fc1)
AP0018.18fc.fd58 uptime is 9 minutes
System returned to ROM by power-on
System image file is "flash:/c1130-k9w8-mx.124-25e.JAO6/c1130-k9w8-mx.124-25e.JAO6"
and then this is version WLC2504
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.6.130.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.101.1
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... Cisco_47:19:c4
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 192.168.100.10
Last Reset....................................... Software reset
System Up Time................................... 0 days 0 hrs 36 mins 45 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
--More-- or (q)uit
Configured Country............................... ID - Indonesia
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +34 C
External Temperature............................. +40 C
Fan Status....................................... 4100 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Burned-in MAC Address............................ 24:E9:B3:47:19:C0
Maximum number of APs supported.................. 5
IP Address management WLC : 192.168.100.10/24
IP Address LAP1142N :192.168.100.102/24
IP Address LAP1131AG : 192.168.100.101/24
Can anyone help my problem?A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected]
cisco AIR-LAP1142N-A-K9 (PowerPC405ex) processor (revision A0) with 90102K/40960K bytes of memory.
Processor board ID FGL1439S15W
PowerPC405ex CPU at 586MHz, revision number 0x147E
Last reset from reload
LWAPP image version 7.6.130.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: C8:4C:75:79:EB:E9
Part Number : 73-12836-03
PCA Assembly Number : 800-33767-03
PCA Revision Number : A0
PCB Serial Number : FOC14234D8Z
Top Assembly Part Number : 800-33775-02
Top Assembly Serial Number : FGL1439S15W
Top Revision Number : A0
Product/Model Number : AIR-LAP1142N-A-K9
cisco AIR-LAP1131AG-A-K9 (PowerPCElvis) processor (revision A0) with 27638K/5120K bytes of memory.
Processor board ID FTX1026T46E
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 7.6.130.0
1 FastEthernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:18:18:FC:FD:58
Part Number : 73-8962-09
PCA Assembly Number : 800-24818-08
PCA Revision Number : A0
PCB Serial Number : FOC102513DE
Top Assembly Part Number : 800-25544-06
Top Assembly Serial Number : FTX1026T46E
Top Revision Number : A0
Product/Model Number : AIR-LAP1131AG-A-K9
Configuration register is 0xF -
OEAP 600 cannot join WLC with auth-list enable
I've got a strange problem here. In the office, my OEAP 600 can join WLC if there is no MAC authentication. When i enable MAC authentication at WLC, AP will fail to register. However, I try it at home and it works with both MAC authentication enable or disable. I suspect it is because of firewall in my office, but there shouldn't have any different in discovery and joining procedure for AP with MAC authentication enable or disable. I'm confused here. Please help.
Justin,
Below is error summary from WLC:
Last Error Summary
Last AP Message Decryption Failure----
Last AP Connection Failure --------- Timed out while waiting for ECHO repsonse from the AP
Last Error Occurred --------- Lwapp join request rejected
Last Error Occurred Reason --------- RADIUS authorization is pending for the AP
The error reason is probaly because I haven't added AP MAC address to ACS. With the same AP, at home using ADSL link, i have no problem.
Thanks. -
Accesspoint shouldnot join WLC
Hi
I have WLC which is having 70 accesspoint associated with it.The model num of accesspoint is 1242.But if any one from outside bring one same model of accesspoint and tried to connect it should not connect.Did any one knows how to configure the controller for this or any other option.One other thing you can do is to make sure you remove option 43 from dhcp, remove dns entry if one was configured, remove any dhcp scope on the subnet the management and ap manager is on, disable otap on the wlc, and remove any ip-helper that is pointing to the wlc. All these features are to help LAP's find the WLC so that they can be part of your WLAN. Once your LAP's are up, there is no reason to have these still configured.
-
My iMac won't join the correct network
This is a new iMac with Lion. The network is ok because all my other devices work fine with it. The network is in the list and when I select it my mac joins without problem, but won't join it automatically. I've also tried to move my network up in the list but that doesn't seem to work either.
Mine is the only network listed in the Perferred Networks List in the advanced settings. The "Remember networks this computer has joined" is checked.
The problem is that when I wake my computer up, it won't find the network. I updated my airport extreme last week and this problem started after that. However, none of the other devices using this network are having any problems. -
Cisco 2702I WAPs won't join 5508 WLC
I haven't been able to get a few WAPs to join my existing WLC and network. They don't seem to be pulling any IP address or talking to DHCP, but everything has been already configured and the same as the other buildings that I have deployed these WAPS on. any thoughts?
Here is the Show Running-Config and Show ip interface brief commands output.
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2015.04.20 13:39:23 =~=~=~=~=~=~=~=~=~=~=~=
show ip interface briefrunning-config
Building configuration...
Current configuration : 17458 bytes
! Last configuration change at 00:00:33 UTC Mon Mar 1 1993
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname APf07f.0692.ff0c
logging rate-limit console 9
enable secret 5 $1$3GAl$UQHPfp.Ab7Ry0HSsQJTRn/
aaa new-model
aaa authentication login default local
--More-- !
aaa session-id common
ip cef
power inline negotiation prestandard source
crypto pki trustpoint airespace-old-root-cert
revocation-check none
rsakeypair Cisco_IOS_MIC_Keys
crypto pki trustpoint airespace-new-root-cert
revocation-check none
rsakeypair Cisco_IOS_MIC_Keys
crypto pki trustpoint airespace-device-root-cert
revocation-check none
rsakeypair Cisco_IOS_MIC_Keys
crypto pki trustpoint cisco-root-cert
--More-- revocation-check none
rsakeypair Cisco_IOS_MIC_Keys
crypto pki trustpoint Cisco_IOS_MIC_cert
revocation-check none
rsakeypair Cisco_IOS_MIC_Keys
crypto pki certificate chain airespace-old-root-cert
certificate ca 00
30820406 3082032F A0030201 02020100 300D0609 2A864886 F70D0101 04050030
818F310B 30090603 55040613 02555331 13301106 03550408 130A4361 6C69666F
726E6961 3111300F 06035504 07130853 616E204A 6F736531 16301406 0355040A
130D6169 72657370 61636520 496E6331 0D300B06 0355040B 13046E6F 6E65310B
30090603 55040313 02636131 24302206 092A8648 86F70D01 09011615 73757070
6F727440 61697265 73706163 652E636F 6D301E17 0D303330 32313232 33333835
355A170D 31323131 31313233 33383535 5A30818F 310B3009 06035504 06130255
53311330 11060355 0408130A 43616C69 666F726E 69613111 300F0603 55040713
0853616E 204A6F73 65311630 14060355 040A130D 61697265 73706163 6520496E
63310D30 0B060355 040B1304 6E6F6E65 310B3009 06035504 03130263 61312430
2206092A 864886F7 0D010901 16157375 70706F72 74406169 72657370 6163652E
636F6D30 81DF300D 06092A86 4886F70D 01010105 000381CD 003081C9 0281C100
DB9D3901 30059DD1 05CB2793 9B9907F8 1FF57FA9 24065BF7 1A5865F8 B9CFCCB3
--More-- 679354D4 69BAB847 1CA327AE EA006AAC 90479C9D C23B67DE FACC0D28 32C6103F
A59C41E2 E8B4250B 4D2903EB 52629A99 D618B747 C4A94151 1AB995BB 14905404
5F4A0B9F F387F346 D5F3A249 2AED1B6A 3DD639D8 4924366A 1234DD2D B13CD489
7E2EA101 63BCCC82 2F7A6D0B 33AB5705 3C784A6D A3DD1E5B 96CF54C6 CF4D59BC
1BFD6CB6 E72FCB29 88DCBE6D 4D76FB83 1FAF5683 E4E20822 00A9EB2E 3BEF0DF9
02030100 01A381EF 3081EC30 1D060355 1D0E0416 04149457 DF7D1482 2D31BB28
772E8996 1886DA46 84BA3081 BC060355 1D230481 B43081B1 80149457 DF7D1482
2D31BB28 772E8996 1886DA46 84BAA181 95A48192 30818F31 0B300906 03550406
13025553 31133011 06035504 08130A43 616C6966 6F726E69 61311130 0F060355
04071308 53616E20 4A6F7365 31163014 06035504 0A130D61 69726573 70616365
20496E63 310D300B 06035504 0B13046E 6F6E6531 0B300906 03550403 13026361
31243022 06092A86 4886F70D 01090116 15737570 706F7274 40616972 65737061
63652E63 6F6D8201 00300C06 03551D13 04053003 0101FF30 0D06092A 864886F7
0D010104 05000381 C100AEB0 349DC0F9 2AAA3A57 75B3A79C 5421A9D0 15389261
95C03479 04DA81D4 120F58FA E2299223 BEB54A90 6D70F7F7 2192EFAF A4B0F488
604E3094 BBCC77A3 60A88129 0849B87B 5CA1AA17 21922A55 6B68E0D3 1ADC7264
C4C4D6B2 33345C86 254E4988 096645CD 40F12761 8BC37E71 DAD91677 25322361
71D87A16 F92AF7C1 51CB8892 443BC666 59BEA47B 985E8866 68A1EBD4 88BBF6E7
A949FDF8 7711D518 A80E203D A12BEBDC 6963EDA7 B76079A3 22380C96 0CB8D324
CADD949D EA39E0EF 033D
quit
crypto pki certificate chain airespace-new-root-cert
certificate ca 00
--More-- 3082045A 30820383 A0030201 02020100 300D0609 2A864886 F70D0101 04050030
81A6310B 30090603 55040613 02555331 13301106 03550408 130A4361 6C69666F
726E6961 3111300F 06035504 07130853 616E204A 6F736531 17301506 0355040A
130E4169 72657370 61636520 496E632E 31143012 06035504 0B130B45 6E67696E
65657269 6E67311A 30180603 55040313 11416972 65737061 63652052 6F6F7420
43413124 30220609 2A864886 F70D0109 01161573 7570706F 72744061 69726573
70616365 2E636F6D 301E170D 30333037 33313133 34313232 5A170D31 33303432
39313334 3132325A 3081A631 0B300906 03550406 13025553 31133011 06035504
08130A43 616C6966 6F726E69 61311130 0F060355 04071308 53616E20 4A6F7365
31173015 06035504 0A130E41 69726573 70616365 20496E63 2E311430 12060355
040B130B 456E6769 6E656572 696E6731 1A301806 03550403 13114169 72657370
61636520 526F6F74 20434131 24302206 092A8648 86F70D01 09011615 73757070
6F727440 61697265 73706163 652E636F 6D3081DF 300D0609 2A864886 F70D0101
01050003 81CD0030 81C90281 C100CCA0 F92330BD 49E947A4 3FA2ACF3 A4827F66
77BB66F4 6B1636BA 84EF0966 9CCAE0EA CA6F1D0F BA90FEFA 58B8502C 10FC78DC
C9D126D8 8F2AD059 A8A69BFE 90324BD6 4553CED9 131B99B0 282A73D9 8655EFAF
5EA54096 22E54B9F C4258988 78F1A51F F47B16F2 0C0A37A3 52603A5A B0DC4533
B0C0B7C8 02DF25F0 585DFF5F 43FDAE1F 48A34BDF F80AC27E 30BE931B D3490ADE
C81FF6F9 974F1408 55C8813F D334F1B8 A1892B0A 10D98A44 7DBF213E 64520D20
E78E9
Not in Bound state.322 DA11CA7A 46ACEB41 46AB0203 010001A3 82011430 82011030 1D060355
1D0E0416 0414538D 8360478D C20F8066 3232E9E1 7070552B 17EA3081 D3060355
--More-- 1D230481 CB3081C8 8014538D 8360478D C20F8066 3232E9E1 7070552B 17EAA181
ACA481A9 3081A631 0B300906 03550406 13025553 31133011 06035504 08130A43
616C6966 6F726E69 61311130 0F060355 04071308 53616E20 4A6F7365 31173015
06035504 0A130E41 69726573 70616365 20496E63 2E311430 12060355 040B130B
456E6769 6E656572 696E6731 1A301806 03550403 13114169 72657370 61636520
526F6F74 20434131 24302206 092A8648 86F70D01 09011615 73757070 6F727440
61697265 73706163 652E636F 6D820100 300C0603 551D1304 05300301 01FF300B
0603551D 0F040403 02010630 0D06092A 864886F7 0D010104 05000381 C10006E3
653D4B19 FAA0C3B9 8EAE23C5 A3305E42 4522A961 BE1B5B88 56ED2E5A E42F7AC0
26AA2805 9824080D 1512169B 44E42847 2EBBA573 29F070DB 56011C7B E9F3A240
399A3557 A50384EC A0353DCF 49E8EC01 94047469 0BC12079 2764873D 25943DCD
66A
*Mar 1 02:26:43.511: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.9726F 4A79EB40 1C7C6897 4E925D80 2313C126 1F604763 A9D9AC1F DF0092F6
57DF1AB4 9B904E22 CE5515CD 44F68A00 4E2BC861 FBC1540D C1F3A66B 8CDDC1C2
7C442027 E6241198 B0E002DE 9E06D64F 0D538987 96C1C0DB 12B0F581 6FED
quit
crypto pki certificate chain airespace-device-root-cert
certificate ca 03
3082047F 308203A8 A0030201 02020103 300D0609 2A864886 F70D0101 04050030
81A6310B 30090603 55040613 02555331 13301106 03550408 130A4361 6C69666F
726E6961 3111300F 06035504 07130853 616E204A 6F736531 17301506 0355040A
130E4169 72657370 61636520 496E632E 31143012 06035504 0B130B45 6E67696E
65657269 6E67311A 30180603 55040313 11416972 65737061 63652052 6F6F7420
43413124 30220609 2A864886 F70D0109 01161573 7570706F 72744061 69726573
--More-- 70616365 2E636F6D 301E170D 30353034 32383232 33373133 5A170D31 35303132
36323233 3731335A 3081A831 0B300906 03550406 13025553 31133011 06035504
08130A43 616C6966 6F726E69 61311130 0F060355 04071308 53616E20 4A6F7365
31173015 06035504 0A130E41 69726573 70616365 20496E63 2E311430 12060355
040B130B 456E6769 6E656572 696E6731 1C301A06 03550403 13134169 72657370
61636520 44657669 63652043 41312430 2206092A 864886F7 0D010901 16157375
70706F72 74406169 72657370 6163652E 636F6D30 81DF300D 06092A86 4886F70D
01010105 000381CD 003081C9 0281C100 A93C0158 E7284E75 FF86A57A 886ACA37
430BECF0 7582F56B DB6AC514 554FB06E AA327B3E CE3C9391 03C93BA4 0C0AF932
A6CB5DA3 F1C3C528 53BF4E19 2C1BFC48 467EBD93 06B4974A 1273BF35 8AD8540F
261E612B A2673B68 D239C87E 1E9E967B 2654D285 45BB7F78 5F4E9D4B 7B8001AA
2F455CFF 4552ECDB 5667E3FC E7093E06 8FAE353D 4228B48D 8B415D9B F496342D
C1459987 B69BFA4B 51FB67B4 A0C21E7F C6269A39 47EB1D48 5E83B129 8B079E5E
1EDAB5A0 BE5E1DE0 109FF0BD 4750E32B 02030100 01A38201 37308201 33300C06
03551D13 04053003 0101FF30 2E060960 86480186 F842010D 0421161F 41697265
73706163 65204465 76696365 20434120 43657274 69666963 61746530 1D060355
1D0E0416 04140A52 3BB12570 523B9CEA 747FB2AD 3D8F95EA 3FCC3081 D3060355
1D230481 CB3081C8 8014538D 8360478D C20F8066 3232E9E1 7070552B 17EAA181
ACA481A9 3081A631 0B300906 03550406 13025553 31133011 06035504 08130A43
616C6966 6F726E69 61311130 0F060355 04071308 53616E20 4A6F7365 31173015
06035504 0A130E41 69726573 70616365 20496E63 2E311430 12060355 040B130B
456E6769 6E656572 696E6731 1A301806 03550403 13114169 72657370 61636520
526F6F74 20434131 24302206 092A8648 86F70D01 09011615 73757070 6F727440
--More-- 61697265 73706163 652E636F 6D820100 300D0609 2A864886 F70D0101 04050003
81C100A0 E8D59D9B DA9EED0C 96045DFE A37084EC 59B5C3D3 71694DB0 70664E0C
8060D69E E366E81F 9F3CCF68 8AB0498E CCFA6CA7 2854F2D8 046690C9 8FEC84EF
2F7F0F08 C90F719D C0F4C125 CED1B525 6DD93E51 777BD5E8 7F1DC79F CC502DC2
0242C05D 1682DEE3 DF7541B8 C55B433C 10DFE2BF D2E802E7 D923329A 23A2076F
86BCC048 D569B383 59AC8979 97F02C55 6F8FE318 754F605C 43CDA7C8 1847B085
1DADF0D6 CD62C8DE A86E6E12 4A7CDCBF A6FCC7E1 852A1DB1 529D63B3 688305F6 7BD25F
quit
crypto pki certificate chain cisco-root-cert
certificate ca 5FF87B282B54DC8D42A315B568C9ADFF
30820343 3082022B A0030201 0202105F F87B282B 54DC8D42 A315B568 C9ADFF30
0D06092A 864886F7 0D010105 05003035 31163014 06035504 0A130D43 6973636F
20537973 74656D73 311B3019 06035504 03131243 6973636F 20526F6F 74204341
20323034 38301E17 0D303430 35313432 30313731 325A170D 32393035 31343230
32353432 5A303531 16301406 0355040A 130D4369 73636F20 53797374 656D7331
1B301906 03550403 13124369 73636F20 526F6F74 20434120 32303438 30820120
300D0609 2A864886 F70D0101 01050003 82010D00 30820108 02820101 00B09AB9
ABA7AF0A 77A7E271 B6B46662 94788847 C6625584 4032BFC0 AB2EA51C 71D6BC6E
7BA8AABA 6ED21588 48459DA2 FC83D0CC B98CE026 68704A78 DF21179E F46105C9
15C8CF16 DA356189 9443A884 A8319878 9BB94E6F 2C53126C CD1DAD2B 24BB31C4
2BFF8344 6FB63D24 7709EABF 2AA81F6A 56F6200F 11549781 75A725CE 596A8265
EFB7EAE7 E28D758B 6EF2DD4F A65E629C CF100A64 D04E6DCE 2BCC5BF5 60A52747
8D69F47F CE1B70DE 701B20D6 6ECDA601 A83C12D2 A93FA06B 5EBB8E20 8B7A91E3
--More-- B568EEA0 E7C40174 A8530B2B 4A9A0F65 120E824D 8E63FDEF EB9B1ADB 53A61360
AFC27DD7 C76C1725 D473FB47 64508180 944CE1BF AE4B1CDF 92ED2E05 DF020103
A351304F 300B0603 551D0F04 04030201 86300F06 03551D13 0101FF04 05300301
01FF301D 0603551D 0E041604 1427F3C8 151E6E9A 020916AD 2BA08960 5FDA7B2F
AA301006 092B0601 04018237 15010403 02010030 0D06092A 864886F7 0D010105
05000382 0101009D 9D8484A3 41A97C77 0CB753CA 4E445062 EF547CD3 75171CE8
E0C6484B B6FE4C3A 198156B0 56EE1996 62AA5AA3 64C1F64E 5433C677 FEC51CBA
E55D25CA F5F0939A 83112EE6 CBF87445 FEE705B8 ABE7DFCB 4BE13784 DAB98B97
701EF0E2 8BD7B0D8 0E9DB169 D62A917B A9494F7E E68E95D8 83273CD5 68490ED4
9DF62EEB A7BEEB30 A4AC1F44 FC95AB33 06FB7D60 0ADEB48A 63B09CA9 F2A4B953
0187D068 A4277FAB FFE9FAC9 40388867 B439C684 6F57C953 DBBA8EEE C043B2F8
09836EFF 66CF3EEF 17B35818 2509345E E3CBD614 B6ECF292 6F74E42F 812AD592
91E0E097 3C326805 854BD1F7 57E2521D 931A549F 0570C04A 71601E43 0B601EFE
A3CE8119 E10B35
quit
crypto pki certificate chain Cisco_IOS_MIC_cert
certificate 2DCD1F0500000015BE7F
30820470 30820358 A0030201 02020A2D CD1F0500 000015BE 7F300D06 092A8648
86F70D01 01050500 30393116 30140603 55040A13 0D436973 636F2053 79737465
6D73311F 301D0603 55040313 16436973 636F204D 616E7566 61637475 72696E67
20434130 1E170D31 34303832 38313834 3030395A 170D3234 30383238 31383530
30395A30 818C310B 30090603 55040613 02555331 13301106 03550408 130A4361
6C69666F 726E6961 3111300F 06035504 07130853 616E204A 6F736531 16301406
--More-- 0355040A 130D4369 73636F20 53797374 656D7331 1B301906 03550403 13124150
3347322D 66303766 30363932 66663063 3120301E 06092A86 4886F70D 01090116
11737570 706F7274 40636973 636F2E63 6F6D3082 0122300D 06092A86 4886F70D
01010105 00038201 0F003082 010A0282 01010095 69DD9DFC D4FC9F91 6781A9EF
51713883 49968E78 05AF6140 CB9A08D9 E1066298 C8F3A072 3AC2FBDB 1E9E43E2
87E6C5A8 2FC83AE1 9C563022 17AD76D8 9D76DFD0 E5C4E01A 3A177708 FE60E3B9
AA362983 6DFBE7A0 7D902420 74C56700 E1DC2DEA 629E9CAE 333E3038 6EC4C07B
2CEF08B7 AC69E43D B06B28C7 8D6226F7 0BC77566 BFFC3B3C 26E90F05 2D342B59
9045D6D2 445313FE B551E815 E09C5872 69DF456F C15A81BA 1F3E6B35 7AE4C2BC
92B4F61B 8E4DEE97 DC569763 32578BBF 909FE970 00445AFA 1CF98D73 D5EC3ED2
ED0A909C 6381E83C 830D8262 23540044 FF438C72 BB21AB47 1E610815 E0737911
78820812 E0ED4512 04E892BD 3FA9DD0A 42409302 03010001 A3820124 30820120
300E0603 551D0F01 01FF0404 030205A0 301D0603 551D0E04 16041417 4C35E9C4
88705E88 3A3DF87C A014FD3E A6ABB930 1F060355 1D230418 30168014 D0C52226
AB4F4660 ECAE0591 C7DC5AD1 B047F76C 303F0603 551D1F04 38303630 34A032A0
30862E68 7474703A 2F2F7777 772E6369 73636F2E 636F6D2F 73656375 72697479
2F706B69 2F63726C 2F636D63 612E6372 6C304C06 082B0601 05050701 01044030
3E303C06 082B0601 05050730 02863068 7474703A 2F2F7777 772E6369 73636F2E
636F6D2F 73656375 72697479 2F706B69 2F636572 74732F63 6D63612E 63657230
3F06092B 06010401 82371402 04321E30 00490050 00530045 00430049 006E0074
00650072 006D0065 00640069 00610074 0065004F 00660066 006C0069 006E0065
300D0609 2A864886 F70D0101 05050003 82010100 59C70FBE 43641BFE 99434812
BEDDE616 093F4F5F 2FF1F0A4 983969F6 CF175C8A 0DF1D329 5A11ADB1 B7E81DF3
--More-- FFBF0415 40884186 2C2C6B2F 99798BEF ECBFCFA5 76D64C5B 0E3FA230 3AFF71D4
ABAB9570 8FA2F2BA 4065622A 1202FDBA 858BD99B 59DCF8AD 729279E2 12CB91BE
7CEEF9BC 667016B6 DB426925 CBE489F3 271EEF13 5CCBA25E 9013D989 66DE5837
1C5EE17B 144256A5 8473189D 8F954745 7D6543B2 1B12ED90 C38C56A7 AC941524
DF999DAB 87510E6B 970CFC97 66FE086A 449B3C99 C22FE3A1 74278F5E 58551DA5
E2442DC3 1A7A991F 4AB107CA 6CD6169E B750494C 23CFAEE3 92507539 E734D21A
F60D6C15 3F551769 D1BE9102 690122D7 A59E2D94
quit
certificate ca 6A6967B3000000000003
308204D9 308203C1 A0030201 02020A6A 6967B300 00000000 03300D06 092A8648
86F70D01 01050500 30353116 30140603 55040A13 0D436973 636F2053 79737465
6D73311B 30190603 55040313 12436973 636F2052 6F6F7420 43412032 30343830
1E170D30 35303631 30323231 3630315A 170D3239 30353134 32303235 34325A30
39311630 14060355 040A130D 43697363 6F205379 7374656D 73311F30 1D060355
04031316 43697363 6F204D61 6E756661 63747572 696E6720 43413082 0120300D
06092A86 4886F70D 01010105 00038201 0D003082 01080282 010100A0 C5F7DC96
943515F1 F4994EBB 9B41E17D DB791691 BBF354F2 414A9432 6262C923 F79AE7BB
9B79E807 294E30F5 AE1BC521 5646B0F8 F4E68E81 B816CCA8 9B85D242 81DB7CCB
94A91161 121C5CEA 33201C9A 16A77DDB 99066AE2 36AFECF8 0AFF9867 07F430EE
A5F8881A AAE8C73C 1CCEEE48 FDCD5C37 F186939E 3D71757D 34EE4B14 A9C0297B
0510EF87 9E693130 F548363F D8ABCE15 E2E8589F 3E627104 8726A415 620125AA
D5DFC9C9 5BB8C9A1 077BBE68 92939320 A86CBD15 75D3445D 454BECA8 DA60C7D8
C8D5C8ED 41E1F55F 578E5332 9349D5D9 0FF836AA 07C43241 C5A7AF1D 19FFF673
--More-- 99395A73 67621334 0D1F5E95 70526417 06EC535C 5CDB6AEA 35004102 0103A382
01E73082 01E33012 0603551D 130101FF 04083006 0101FF02 0100301D 0603551D
0E041604 14D0C522 26AB4F46 60ECAE05 91C7DC5A D1B047F7 6C300B06 03551D0F
04040302 01863010 06092B06 01040182 37150104 03020100 30190609 2B060104
01823714 02040C1E 0A005300 75006200 43004130 1F060355 1D230418 30168014
27F3C815 1E6E9A02 0916AD2B A089605F DA7B2FAA 30430603 551D1F04 3C303A30
38A036A0 34863268 7474703A 2F2F7777 772E6369 73636F2E 636F6D2F 73656375
72697479 2F706B69 2F63726C 2F637263 61323034 382E6372 6C305006 082B0601
05050701 01044430 42304006 082B0601 05050730 02863468 7474703A 2F2F7777
772E6369 73636F2E 636F6D2F 73656375 72697479 2F706B69 2F636572 74732F63
72636132 3034382E 63657230 5C060355 1D200455 30533051 060A2B06 01040109
15010200 30433041 06082B06 01050507 02011635 68747470 3A2F2F77 77772E63
6973636F 2E636F6D 2F736563 75726974 792F706B 692F706F 6C696369 65732F69
6E646578 2E68746D 6C305E06 03551D25 04573055 06082B06 01050507 03010608
2B060105 05070302 06082B06 01050507 03050608 2B060105 05070306 06082B06
01050507 0307060A 2B060104 0182370A 0301060A 2B060104 01823714 02010609
2B060104 01823715 06300D06 092A8648 86F70D01 01050500 03820101 0030F330
2D8CF2CA 374A6499 24290AF2 86AA42D5 23E8A2EA 2B6F6923 7A828E1C 4C09CFA4
4FAB842F 37E96560 D19AC6D8 F30BF5DE D027005C 6F1D91BD D14E5851 1DC9E3F7
38E7D30B D168BE8E 22A54B06 E1E6A4AA 337D1A75 BA26F370 C66100A5 C379265B
A719D193 8DAB9B10 11291FA1 82FDFD3C 4B6E65DC 934505E9 AF336B67 23070686
22DAEBDC 87CF5921 421AE9CF 707588E0 243D5D7D 4E963880 97D56FF0 9B71D8BA
6019A5B0 6186ADDD 6566F6B9 27A2EE2F 619BBAA1 3061FDBE AC3514F9 B82D9706
--More-- AFC3EF6D CC3D3CEB 95E981D3 8A5EB6CE FA79A46B D7A25764 C43F4CC9 DBE882EC
0166D410 88A256E5 3C57EDE9 02A84891 6307AB61 264B1A13 9FE4DCDA 5F
quit
username Cisco secret 5 $1$.UkK$3GDTdydbzaupRq0u6bml9/
ip ssh version 2
bridge irb
interface GigabitEthernet0
duplex auto
speed auto
interface GigabitEthernet0.1
encapsulation dot1Q 1 native
bridge-group 1
bridge-group 1 spanning-disabled
interface GigabitEthernet1
shutdown
duplex auto
--More-- speed auto
bridge-group 1
interface BVI1
ip address dhcp client-id BVI1
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 BVI1
logging trap emergencies
logging facility kern
logging snmp-trap notifications
logging snmp-trap informational
logging snmp-trap debugging
bridge 1 protocol ieee
bridge 1 route ip
line con 0
line vty 0 4
transport input all
line vty 5 15
transport input all
--More-- end
APf07f.0692.ff0c# show running-configip interface brief
Interface IP-Address OK? Method Status Protocol
BVI1 unassigned YES DHCP up up
GigabitEthernet0 unassigned NO unset up up
GigabitEthernet0.1 unassigned YES unset up up
GigabitEthernet1 unassigned NO unset administratively down down
APf07f.0692.ff0c#
Not in Bound state.
*Mar 1 02:27:33.511: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
Not in Bound state.
*Mar 1 02:28:23.511: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
Not in Bound state.
*Mar 1 02:29:13.511: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
Not in Bound state.
*Mar 1 02:30:03.511: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.Hi,
First check that a DHCP pool is configured for APs to pull IP address then only AP will be try to discover the WLC.
Most of the time these problem(AP join) arise when you don't have correct software version on WLC.
For 2702 AP, you need at-least 7.6.120.0 version on WLC.
Here is the matrix: http://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html
Fore more info, paste the info which Rasika asked.
Regards -
Hello Guys,
I have converted ap 1131 from autonomous to lwapp successfully by using upgrade utility tool but the AP does not join the WLC 2106. I can see it as a neighbor on the switch with no IP address. please help me.
Thank youHello Scott,
Thank you for the reply
Please find the attached file for the config, i found out that i have not updated the time on WLC but i did update the time on WLC and tested for other AP and this one too wont join the WLC. The ap are located remote.
atsg-wl1#show run | incl hostname
hostname atsg-wl1
atsg-wl1#test pb display
Display of the Parameter Block
Total Number of Records : 7
Number of Certs : 6
Number of Keys : 1
atsg-wl1#term length 0
atsg-wl1#show version | include Cisco IOS
Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.3(7)JA3, RELEASE SOFTWARE (fc1)
atsg-wl1#show controller | include Radio AIR
Radio AIR-AP1131G, Base Address 0019.0737.02f0, BBlock version 0.00, Software version 5.80.15
Radio AIR-AP1131A, Base Address 0019.073b.02d0, BBlock version 0.00, Software version 5.80.15
atsg-wl1#show controllers d0 | include Current
Current Frequency: 2447 MHz Channel 8
Current CCK Power: 14 dBm
Current OFDM Power: 14 dBm
Current Rates: basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
atsg-wl1#show controllers d1 | include Current
Current Frequency: 5805 MHz Channel 161
Current Power: 17 dBm
Current Rates: basic-6.0 9.0 basic-12.0 18.0 basic-24.0 36.0 48.0 54.0
atsg-wl1#show run | include station-role
station-role root
station-role root
atsg-wl1#test pb disp
Display of the Parameter Block
Total Number of Records : 7
Number of Certs : 6
Number of Keys : 1
atsg-wl1#show int F0 | include address
Hardware is PowerPCElvis Ethernet, address is 0019.555f.ccfa (bia 0019.555f.ccfa)
atsg-wl1#show int | include Dot11Radio
Dot11Radio0 is up, line protocol is up
Dot11Radio1 is up, line protocol is up
atsg-wl1#show sntp | exclude SNTP
10.148.0.1 16 1 never
172.16.21.57 16 1 never
Broadcast client mode is enabled.
atsg-wl1#show run
Building configuration...
Current configuration : 6025 bytes
! Last configuration change at 19:35:46 UTC Thu Jan 31 2013 by didata
! NVRAM config last updated at 19:13:48 UTC Fri Feb 1 2013 by didata
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime localtime
service password-encryption
hostname atsg-wl1
logging buffered informational
logging console informational
enable secret 5
ip subnet-zero
ip domain name aspentech.com
ip name-server 10.96.16.230
ip name-server 10.148.0.249
ip name-server 10.32.19.1
aaa new-model
aaa group server radius rad_eap
server 10.16.16.123 auth-port 1645 acct-port 1646
aaa authentication login default group tacacs+ local
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authentication enable default group tacacs+ enable
aaa authorization exec default group tacacs+ local
aaa authorization commands 15 default group tacacs+ local
aaa accounting exec default start-stop group tacacs+
aaa accounting commands 15 default start-stop group tacacs+
aaa accounting system default start-stop group tacacs+
aaa session-id common
no dot11 igmp snooping-helper
dot11 ssid
authentication open eap eap_methods
authentication network-eap eap_methods
guest-mode
infrastructure-ssid optional
dot11 network-map
power inline negotiation prestandard source
usernamepassword 7
username privilege 15 password 7
usernamep rivilege 15 password 7
class-map match-all _class_Protocol_301_C351
match access-group name Voice_Over_IP_301
class-map match-all _class_8
match ip dscp cs1
class-map match-all _class_0
match ip dscp default
class-map match-all _class_48
match ip dscp cs6
class-map match-all _class_18
match ip dscp af21
class-map match-all _class_24
match ip dscp cs3
class-map match-all _class_16
match ip dscp cs2
class-map match-all _class_34
match ip dscp af41
class-map match-all _class_26
match ip dscp af31
class-map match-all _class_40
match ip dscp cs5
class-map match-all _class_46
match ip dscp ef
class-map match-all _class_56
match ip dscp cs7
class-map match-all _class_10
match ip dscp af11
class-map match-all _class_32
match ip dscp cs4
policy-map _policy_Voice_Over_IP_202
class _class_Protocol_301_C351
set cos 6
policy-map _policy_fallback_policy
class _class_0
set cos 0
class _class_8
set cos 1
class _class_10
set cos 1
class _class_16
set cos 2
class _class_18
set cos 2
class _class_24
set cos 3
class _class_26
set cos 3
class _class_32
set cos 4
class _class_34
set cos 4
class _class_40
set cos 5
class _class_46
set cos 5
class _class_48
set cos 6
class _class_56
set cos 7
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
shutdown
encryption mode wep mandatory mic key-hash
broadcast-key change 900
ssid
traffic-class background cw-min 5 cw-max 8 fixed-slot 2
traffic-class best-effort cw-min 5 cw-max 8 fixed-slot 6
traffic-class video cw-min 4 cw-max 6 fixed-slot 1
traffic-class voice cw-min 3 cw-max 7 fixed-slot 1
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
packet retries 32
fragment-threshold 2338
station-role root
rts threshold 2339
rts retries 32
world-mode legacy
no cdp enable
infrastructure-client
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
encryption mode wep mandatory mic key-hash
broadcast-key change 900
ssid aspen100abcdefgh
speed basic-6.0 9.0 basic-12.0 18.0 basic-24.0 36.0 48.0 54.0
station-role root
world-mode legacy
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 10.148.0.7 255.255.255.0
no ip route-cache
ip default-gateway 10.148.0.1
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip tacacs source-interface BVI1
ip radius source-interface BVI1
ip access-list extended Voice_Over_IP_300
permit 119 any any
permit ip any any
ip access-list extended Voice_Over_IP_301
permit 119 any any
permit ip any any
logging facility local0
snmp-server view iso_view iso included
snmp-server community admin view iso_view RW
snmp-server community all4114all view iso_view RW
snmp-server community ddbos2000 RO
snmp-server location ATSG
snmp-server contact James Lee
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps tty
snmp-server enable traps disassociate
snmp-server enable traps deauthenticate
snmp-server enable traps authenticate-fail
snmp-server enable traps config
snmp-server enable traps syslog
snmp-server host 192.135.137.12 ddbos2000
tacacs-server host 10.16.16.123 key 7
tacacs-server host 10.96.16.245 key 7
tacacs-server directed-request
radius-server host 10.16.16.123 auth-port 1645 acct-port 1646 timeout 5 retransmit 3 key 7
radius-server deadtime 120
radius-server vsa send accounting
radius-server vsa send authentication
control-plane
bridge 1 route ip
line con 0
transport preferred all
transport output all
stopbits 1
line vty 0 4
exec-timeout 0 0
transport preferred all
transport input all
transport output all
line vty 5 15
exec-timeout 0 0
transport preferred all
transport input all
transport output all
end
atsg-wl1#show run | incl hostname
hostname atsg-wl1
atsg-wl1#arch down /over /create-space tftp://10.148.0.118/images/c1130-rcvk $over /create-space tftp://10.148.0.118/images/c1130-rcvk9 w8-tar.12 te-space tftp://10.148.0.118/images/c1130-rcvk9w8-tar.123 -11.JX1.t ftp://10.148.0.118/images/c1130-rcvk9w8-tar.123-11.JX1.ta r
examining image...
Loading images/c1130-rcvk9w8-tar.123-11.JX1.tar from 10.148.0.118 (via BVI1): !
extracting info (273 bytes)!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
[OK - 1873920 bytes]
Image info:
Version Suffix: rcvk9w8-
Image Name: c1130-rcvk9w8-mx
Version Directory: c1130-rcvk9w8-mx
Ios Image Size: 1874432
Total Image Size: 1874432
Image Feature: WIRELESS LAN|LWAPP|RECOVERY
Image Family: C1130
Wireless Switch Management Version: 3.0.51.0
Extracting files...
Loading images/c1130-rcvk9w8-tar.123-11.JX1.tar from 10.148.0.118 (via BVI1): !
extracting info (273 bytes)
c1130-rcvk9w8-mx/ (directory) 0 (bytes)
extracting c1130-rcvk9w8-mx/c1130-rcvk9w8-mx (1867816 bytes)!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
extracting c1130-rcvk9w8-mx/info (273 bytes)
extracting info.ver (273 bytes)!
[OK - 1873920 bytes]
Deleting current version...
Deleting flash:/c1130-k9w7-mx.123-7.JA3...done.
New software image installed in flash:/c1130-rcvk9w8-mx
Configuring system to use new image...done.
atsg-wl1#show archive status
SUCCESS: Upgrade complete.
atsg-wl1#write erase
Erasing the nvram filesystem will remove all configuration files! Continue? [confirm]
[OK]
Erase of nvram: complete
atsg-wl1#dir flash:
Directory of flash:/
2 -rwx 2072 Jan 31 2013 19:36:18 +00:00 private-multiple-fs
149 drwx 128 Jan 31 2013 19:36:11 +00:00 c1130-rcvk9w8-mx
4 -rwx 342 Jan 31 2013 19:36:14 +00:00 env_vars
15998976 bytes total (14126080 bytes free)
atsg-wl1#dir nvram:
Directory of nvram:/
30 -rw- 0 startup-config
31 ---- 0 private-config
1 -rw- 0 ifIndex-table
2 ---- 12 persistent-data
32768 bytes total (30668 bytes free)
atsg-wl1#sh crypto ca trustpoints
atsg-wl1#sh crypto ca certificates
atsg-wl1#terminal length 0
atsg-wl1#show run | begin BVI1
interface BVI1
ip address 10.148.0.7 255.255.255.0
no ip route-cache
ip default-gateway 10.148.0.1
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip tacacs source-interface BVI1
ip radius source-interface BVI1
ip access-list extended Voice_Over_IP_300
permit 119 any any
permit ip any any
ip access-list extended Voice_Over_IP_301
permit 119 any any
permit ip any any
logging facility local0
snmp-server view iso_view iso included
snmp-server community admin view iso_view RW
snmp-server community all4114all view iso_view RW
snmp-server community ddbos2000 RO
snmp-server location ATSG
snmp-server contact James Lee
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps tty
snmp-server enable traps disassociate
snmp-server enable traps deauthenticate
snmp-server enable traps authenticate-fail
snmp-server enable traps config
snmp-server enable traps syslog
snmp-server host 192.135.137.12 ddbos2000
tacacs-server host 10.16.16.123 key 7
tacacs-server host 10.96.16.245 key 7
tacacs-server directed-request
radius-server host 10.16.16.123 auth-port 1645 acct-port 1646 timeout 5 retransmit 3 key 7
radius-server deadtime 120
radius-server vsa send accounting
radius-server vsa send authentication
control-plane
bridge 1 route ip
line con 0
transport preferred all
transport output all
stopbits 1
line vty 0 4
exec-timeout 0 0
transport preferred all
transport input all
transport output all
line vty 5 15
exec-timeout 0 0
transport preferred all
transport input all
transport output all
end -
AP not joining WLC b/c of DHCP.
This is the first time that I've dealt with a WLC, so I'm trying to do a real simple setup. I have a WLC 2106 and a few LAP 1141N's. I'm trying to set them up on a single VLAN, no RADIUS server, and I want my router to handle DHCP (not the WLC). Here's the info I setup the WLC with:
Welcome to the Cisco Wizard Configuration Tool
Use the '-' character to backup
System Name [Cisco_94:40:40]: WLC
Enter Administrative User Name (24 characters max): cisco
Enter Administrative Password (24 characters max): *****
Management Interface IP Address: 192.168.3.5
Management Interface Netmask: 255.255.255.0
Management Interface Default Router: 192.168.3.1
Management Interface VLAN Identifier (0 = untagged): 0
Management Interface Port Num [1 to 4]: 1
Management Interface DHCP Server IP Address: 192.168.3.1
AP Manager Interface IP Address: 192.168.3.6
AP-Manager is on Management subnet, using same values
AP Manager Interface DHCP Server (192.168.3.1):
Virtual Gateway IP Address: 1.1.1.1
Mobility/RF Group Name: GroupRF
Network Name (SSID): Test
Allow Static IP Addresses [YES][no]: yes
Configure a RADIUS Server now? [YES][no]: no
Warning! The default WLAN security policy requires a RADIUS server.
Please see documentation for more details.
Enter Country Code (enter 'help' for a list of countries) [US]: US
Enable 802.11b Network [YES][no]: Yes
Enable 802.11a Network [YES][no]: no
Enable 802.11g Network [YES][no]: yes
Enable Auto-RF [YES][no]: yes
Configuration saved!
Resetting system with new configuration...
When I login to the web interface of the WLC (https://192.168.3.5) it doesn't show any AP's as joining even though I have one plugged in to the WLC. I console'd into the AP and this is the error that keeps on repeating:
*Mar 1 00:51:45.962: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
Am I missing something? I already checked the WLC, and the date/time is setup correctly. And I know my router (at 192.168.3.1) is handing out DHCP. Everything is on the same subnet so I don't understand why I'm having such a hard time with this. I've tried my hardest searching online but haven't found anything. Any help would REALLY be appreciated. Thank you very much.
P.S. If you have any other questions please feel free to ask.The answer is that LWAPP / CAPWAP APs need to be connected to an access port on a swtich (configured with the proper VLAN) as they do nothing more than pass the traffic to the WLC through the LWAPP / CAPWAP tunnel. The WLC ethernet ports are configured as trunks and can not be change. This is because the WLC is where all the VLAN tagging takes place.
Hope that helps,
Scott
Please rate this post if you found it helpful.
Maybe you are looking for
-
Home Sharing: Can't see anyone's iTunes
My iTunes is detectable on other computers but mine won't detect anyone's. We are on same network. I have closed and opened iTunes, I have tried different homesharing accounts. Fixed firewall stuff and network stuff. My brother and I both have HP com
-
Optimum domain not found page coming up?
Hi, for some reason, recently, when I type a URL without the end (.com/net/org/etc.), instead of automatically going to a page, I get an Optimum domain not found page. The weird thing is, my mom uses the same internet provider and network but doesn't
-
Itunes shuts down when loading music to ipod Touch
I just bought a new PC running Windows 7. Everything is set up correctly in iTunes. When I first synced the iPod Touch it loaded about a third of my music before I got an error message saying iTunes had stopped working and needed to shut down. Now, a
-
What are the document upload limits?
I have placed five document upload sections on a FormsCentral form that I have created. Are my customers going to encounter any problems with built in limits that do not allow more than one or three documents to be uploaded for a single form?
-
How to view what are all programs maped with the event....
I am new to this events concept - could you please say in SM64 we can give Event.... <b>How to view what are all programs maped with the event..</b> Thanks in advance.