13 inch mid 09 MBP will not boot in safe mode or os disc. originally kernal panic but now blank screen. is this logic board? no liquid damage.

I upgraded the ram and hdd a while back(RAM first with no issues, then hdd around 2 months later). The computer started freezing a few days after the hdd upgrade.
I reformatted the hdd and it worked fine for a few weeks then same freezing issue. Instead of wiping the drive again I repaired the disc and this had it fixed for about a month. I was booting in safe mode for a few days with no issue and went about uninstalling 3rd party apps. Then the Kernal panic issue started, When I inserted the OS cd the screen went blank and has not come back on after repeated boots.
Can we put this down to logic board and if so can it be repaired rather than replaced?
Thanks

thanks for the reply,
just reinstalled the factory RAM and HDD. Same issue of blank screen. At the moment i have no way of connecting to external monitor.
The OS cd is still in drive and i can hear the drive spinning for a few seconds at the start but it stops after about 20 seconds.

Similar Messages

I have a macbook 2011 and its booting to the apple with a loading bar. it gets halfway and changes to a screen with the apple and a spinning circle. It spins untill it dies. will not boot to safe mode. Do not have orriginal osx disk either.... HELP :(

i have a macbook 2011 and its booting to the apple with a loading bar. it gets halfway and changes to a screen with the apple and a spinning circle. It spins untill it dies. will not boot to safe mode. Do not have orriginal osx disk either.... HELP

It happened after an update

HT201262 Will not boot into safe mode

Hello,
My MacBook pro 2012 crashed last night. Could not force quite so closed it down. On restart it would get halfway then stop. I have japped p-ram (I know it is my called this anymore) but then loads halfway and the turns off. I booted into disk repair and it found a couple of problems so repaired successfully. On restart it still gets halfway then turns off.
From reading the apple support it seems other people have the same problem. All mention booting into safe mode. For the life of me I cannot get my machine to boot into safe mode!
I do exactly like the instructions say but it always just goes to the page where I choose whether to log in as me or a guest.
What am I doing wrong?!
I am on a MacBook pro running Yosemite.
Many thanks for any help.
Chris.

Startup Issues - Resolve
Startup Issues - Resolve (2)
Startup Issues - Resolve (3)

Pre-Intel Imac G5 17" Will not boot past safe mode, tried everything!

I have a 17" Imac with leopard that has been working fine until just recently stopped booting in anything other than safe mode. It will load the apple screen fine, then a ghost mouse image appears in the top left corner, which then appears, and sticks like you can move it. The blue screen appears and you now have your normal mouse that you can move around with the other one still froze in place, then the blue screen turns dark blue, then black and thats it. Your left with the mouse and a black screen and nothing else. I have tried resetting the ram, the hard drive checker command, apple, F O commands, single user mode, I checked the LEDS on the back the first one is always on, the second comes right on and the third lights when its supposed to. I did a complete erase and install of leopard and when the computer booted up you saw the the ghost arrow, and the same thing, but I waited awhile and you could hear the "Welcome to Leopard" music playing in the background It just doesn't make sense why the computer is not booting. Any advice is appreciated. I have tried it all. I am an apple lover, but this is one time where I am honestly about to throw it to the road.

Welcome to Discussions - from what I have seen, this could be your capacitors on your logic board about to fail, I'm afraid the cure would be a new logic bard. If you can take the back off and check to see whether the tops of the caps are bulging, that would be a definitive clue.

Macbook will not boot in safe mode

I tried to install the new Maverick OS X software but it is telling me that the install failed because the disk Macintosh HD is damaged and can't be repaired. I tried to restart my mac in safe mood so I can back up my important documents but the gear just keeps spinning. Can someone please help me!!!

Which model MacBook Pro do you have? Have you tried booting into your Recovery partition (holding down the command and R keys whilst booting)? If your MBP supporst it, have you tried Internet recovery (holding down the command, option and R keys whilst booting)?
Call back,
Clinton

IMac 27 inch i7 OSX Lion will not boot up from Hard Disc

iMac 27 inch i7 OSX Lion will not boot up from Hard Disc on cold start, and cannot find wifi hardware in the machine. Restart and everything is fine. I have two machine and they behave the same. Software or hardware problem?

First of all, try a hard restart; making sure no disks are in the slot, unplug everything from your computer (keyboards, mice, etc.) and then unplug the computer itself. Leave it unplugged for a minute or two, then plug it back in and boot it up.
If that fails, reboot it while holding down the option-key on your keyboard. The screen should show a choice of which disk drive to boot from. Choose your usual drive.
If that fails, reboot it while holding down the shift-key on your keyboard. It should take a while for it to boot up, as it is destroying all connections to sources that may contain a virus.
If that fails, reboot it while holding down keys "option-command-P-R" until you hear the startup tone a second time.
If that fails, reboot it while holding down the C-key. Make sure you have inserted the installation disk before doing this step.
If that fails, reboot it while holding down the command-key and the R-key.
If that fails, please reply to this and let me know.

IMac will not boot from any mode except Target Disk

I have an Early 2008 Penryn iMac 24" MB398LL/A running OS X 10.7.4 (see specs below) that will not boot from ANY mode, It also has several strange vertical bars from top to bottom on the screen. They are about 10 px wide, with some pixels empty and looks a bit like a barcode if you squint at it.
I have tried Safe Boot, Force Boot, DVD Boot, FireWire/USB Boot, and it always gets to the same point. It gets to the apple screen with the spinning gear and then after about 8 seconds it freezes. The only way it works at all is in Target Disk Mode. It pops right up on my Macbook Pro and I was able to grab all my info!
I have run Disc Utilities and Tech Tool on it many times from my MBP and it passes every test.
I reformatted the HD and installed 10.7 again, it still freezes up at the same point.
I have tried using Single User mode and every time have had to run /sbin/fsck -fy twice because it always says the disk is ok but it was modified on the first pass.
I thought maybe it had a bad video card or logic board but and I ran the Apple Hardware Test on many occasions and it always passes. Recently I was told about Loop Mode and just completed running the AHT for just over 30 hours without any errors at all.
UPDATE...
Strange Part… I tried installing Mountain Lion in Target Disk Mode and everything went smoothly. When it restarted on its own the lines on the screen were gone for the moment, but the Mac still freezes up on the spinning gear and immediately restarts on its own. I have run every thing listed above on it and still nothing. Sometimes the lines reappear then in two more starts they are gone.
I did manage to have it start one time got a copy of the the error report (its at the bottom too) The Mac ran for at least 30 minutes with no problems, then the screen went crazy a few seconds and it became unresponsive. The mouse moved but that was all it could do. Now my iMac continually restarts itself, I don't have any more ideas, HELP!
Specs...
The iMac "Core 2 Duo" 3.06 24-Inch Aluminum (Early 2008/Penryn) features a 3.06 GHz Intel "Core 2 Duo" processor (E8435), with two independent processor "cores" on a single silicon chip, a 6 MB shared level 2 cache, a 1066 MHz system bus, 2 GB of RAM (800 MHz DDR2 SDRAM, PC2-6400), a 500 GB (7200 RPM) Serial ATA hard drive, a vertically-mounted slot-loading DVD±R DL "SuperDrive", NVIDIA GeForce 8800 GS graphics acceleration with 512 MB of GDDR3 memory, a built-in iSight video camera, and built-in stereo speakers underneath the 24" glossy TFT Active Matrix LCD (1920x1200 native) display.
Error Report…
Sat Sep 1 17:13:12 2012
panic(cpu 0 caller 0xffffff801a4b7b95): Kernel trap at 0xffffff7f9bab8654, type 14=page fault, registers:
CR0: 0x000000008001003b, CR2: 0x0000000000000010, CR3: 0x0000000011803000, CR4: 0x0000000000000660
RAX: 0x0000000000000001, RBX: 0xffffff8050e00000, RCX: 0xffffff801aa8eb00, RDX: 0xffffff80602dba38
RSP: 0xffffff80602dbb60, RBP: 0xffffff80602dbb60, RSI: 0x0000000000000000, RDI: 0x0000000000000000
R8: 0x0000000000000000, R9: 0x00000000000000ff, R10: 0xffffffffffffffff, R11: 0x00000000ffffffff
R12: 0xffffff8050e00000, R13: 0x0000000000000000, R14: 0x0000000000000002, R15: 0x0000000000000000
RFL: 0x0000000000010246, RIP: 0xffffff7f9bab8654, CS: 0x0000000000000008, SS: 0x0000000000000010
Fault CR2: 0x0000000000000010, Error code: 0x0000000000000000, Fault CPU: 0x0

Here is the complete error log...
Sat Sep 1 17:13:12 2012
panic(cpu 0 caller 0xffffff801a4b7b95): Kernel trap at 0xffffff7f9bab8654, type 14=page fault, registers:
CR0: 0x000000008001003b, CR2: 0x0000000000000010, CR3: 0x0000000011803000, CR4: 0x0000000000000660
RAX: 0x0000000000000001, RBX: 0xffffff8050e00000, RCX: 0xffffff801aa8eb00, RDX: 0xffffff80602dba38
RSP: 0xffffff80602dbb60, RBP: 0xffffff80602dbb60, RSI: 0x0000000000000000, RDI: 0x0000000000000000
R8: 0x0000000000000000, R9: 0x00000000000000ff, R10: 0xffffffffffffffff, R11: 0x00000000ffffffff
R12: 0xffffff8050e00000, R13: 0x0000000000000000, R14: 0x0000000000000002, R15: 0x0000000000000000
RFL: 0x0000000000010246, RIP: 0xffffff7f9bab8654, CS: 0x0000000000000008, SS: 0x0000000000000010
Fault CR2: 0x0000000000000010, Error code: 0x0000000000000000, Fault CPU: 0x0
Backtrace (CPU 0), Frame : Return Address
0xffffff80602db800 : 0xffffff801a41d5f6
0xffffff80602db870 : 0xffffff801a4b7b95
0xffffff80602dba40 : 0xffffff801a4ce4ad
0xffffff80602dba60 : 0xffffff7f9bab8654
0xffffff80602dbb60 : 0xffffff7f9baa218c
0xffffff80602dbbb0 : 0xffffff7f9baa20e2
0xffffff80602dbbd0 : 0xffffff7f9ba73554
0xffffff80602dbc00 : 0xffffff7f9aa8d470
0xffffff80602dbc40 : 0xffffff7f9aa8d3df
0xffffff80602dbc60 : 0xffffff7f9aa926ec
0xffffff80602dbcf0 : 0xffffff7f9aa8af20
0xffffff80602dbd20 : 0xffffff7f9aadacc7
0xffffff80602dbd70 : 0xffffff801a833b9b
0xffffff80602dbdc0 : 0xffffff801a862d57
0xffffff80602dbe30 : 0xffffff801a497cef
0xffffff80602dbe80 : 0xffffff801a420abd
0xffffff80602dbeb0 : 0xffffff801a410448
0xffffff80602dbf00 : 0xffffff801a4195fb
0xffffff80602dbf70 : 0xffffff801a4a5ad6
0xffffff80602dbfb0 : 0xffffff801a4ced13
      Kernel Extensions in backtrace:
         com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000->0xffffff7f9aab8fff
            dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
         com.apple.NVDAResman(8.0)[6A699209-FB98-316B-A3C0-DCA82AA8C86B]@0xffffff7f9aad8 000->0xffffff7f9addafff
            dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
            dependency: com.apple.iokit.IONDRVSupport(2.3.4)[99CA4184-8D92-31B2-8726-46139E8E3DFF]@0xff ffff7f9aac4000
            dependency: com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000
         com.apple.GeForce(8.0)[4B9BE287-5251-398E-96B0-BB16C9BFB2D9]@0xffffff7f9ba72000 ->0xffffff7f9bb34fff
            dependency: com.apple.NVDAResman(8.0.0)[6A699209-FB98-316B-A3C0-DCA82AA8C86B]@0xffffff7f9aa d8000
            dependency: com.apple.iokit.IONDRVSupport(2.3.4)[99CA4184-8D92-31B2-8726-46139E8E3DFF]@0xff ffff7f9aac4000
            dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
            dependency: com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000
BSD process name corresponding to current thread: WindowServer
Mac OS version:
12B19
Kernel version:
Darwin Kernel Version 12.1.0: Tue Aug 14 13:29:55 PDT 2012; root:xnu-2050.9.2~1/RELEASE_X86_64
Kernel UUID: 3005059E-270B-3B9F-940D-7A66C05DDC9D
Kernel slide:     0x000000001a200000
Kernel text base: 0xffffff801a400000
System model name: iMac8,1 (Mac-F227BEC8)
System uptime in nanoseconds: 26349024446
last loaded kext at 22534854703: com.apple.driver.AppleHDAHardwareConfigDriver          2.3.0f2 (addr 0xffffff7f9c489000, size 12288)
loaded kexts:
com.apple.driver.AppleHDAHardwareConfigDriver          2.3.0f2
com.apple.driver.AppleHDA          2.3.0f2
com.apple.driver.AppleTyMCEDriver          1.0.2d2
com.apple.filesystems.autofs          3.0
com.apple.iokit.IOBluetoothSerialManager          4.0.9f8
com.apple.iokit.IOBluetoothUSBDFU          4.0.9f8
com.apple.driver.AppleLPC          1.6.0
com.apple.driver.AppleMuxControl          3.2.6
com.apple.driver.AppleBacklight          170.2.3
com.apple.driver.AppleUpstreamUserClient          3.5.10
com.apple.driver.AppleMCCSControl          1.0.33
com.apple.GeForce          8.0.0
com.apple.driver.AppleSMCPDRC          1.0.0
com.apple.iokit.IOUserEthernet          1.0.0d1
com.apple.Dont_Steal_Mac_OS_X          7.0.0
com.apple.driver.ApplePolicyControl          3.2.6
com.apple.driver.ACPI_SMC_PlatformPlugin          1.0.0
com.apple.driver.AppleIRController          320.15
com.apple.iokit.SCSITaskUserClient          3.5.1
com.apple.driver.AppleFileSystemDriver          3.0.1
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless          1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib          1.0.0d1
com.apple.BootCache          34
com.apple.driver.XsanFilter          404
com.apple.iokit.IOAHCIBlockStorage          2.2.1
com.apple.driver.AppleFWOHCI          4.9.5
com.apple.driver.AppleUSBHub          5.1.6
com.apple.driver.AirPortBrcm43224          600.36.17
com.apple.iokit.AppleYukon2          3.2.3b1
com.apple.driver.AppleAHCIPort          2.4.0
com.apple.driver.AppleIntelPIIXATA          2.5.1
com.apple.driver.AppleUSBEHCI          5.1.5
com.apple.driver.AppleUSBUHCI          5.1.5
com.apple.driver.AppleEFINVRAM          1.6.1
com.apple.driver.AppleRTC          1.5
com.apple.driver.AppleHPET          1.7
com.apple.driver.AppleACPIButtons          1.6
com.apple.driver.AppleSMBIOS          1.9
com.apple.driver.AppleACPIEC          1.6
com.apple.driver.AppleAPIC          1.6
com.apple.driver.AppleIntelCPUPowerManagementClient          196.0.0
com.apple.nke.applicationfirewall          4.0.39
com.apple.security.quarantine          2
com.apple.driver.AppleIntelCPUPowerManagement          196.0.0
com.apple.driver.DspFuncLib          2.3.0f2
com.apple.iokit.IOAudioFamily          1.8.9fc9
com.apple.kext.OSvKernDSPLib          1.6
com.apple.kext.triggers          1.0
com.apple.iokit.IOSerialFamily          10.0.6
com.apple.driver.AppleSMBusPCI          1.0.10d0
com.apple.driver.AppleBacklightExpert          1.0.4
com.apple.driver.AppleSMBusController          1.0.10d0
com.apple.nvidia.nv50hal          8.0.0
com.apple.NVDAResman          8.0.0
com.apple.iokit.IOFireWireIP          2.2.5
com.apple.driver.AppleHDAController          2.3.0f2
com.apple.iokit.IOHDAFamily          2.3.0f2
com.apple.iokit.IOSurface          86.0.2
com.apple.iokit.IOBluetoothFamily          4.0.9f8
com.apple.driver.AppleGraphicsControl          3.2.6
com.apple.iokit.IONDRVSupport          2.3.4
com.apple.iokit.IOGraphicsFamily          2.3.4
com.apple.driver.AppleSMC          3.1.3d11
com.apple.driver.IOPlatformPluginLegacy          1.0.0
com.apple.driver.IOPlatformPluginFamily          5.2.0d16
com.apple.iokit.IOUSBHIDDriver          5.0.0
com.apple.driver.AppleUSBMergeNub          5.1.5
com.apple.driver.AppleUSBComposite          5.0.0
com.apple.iokit.IOSCSIMultimediaCommandsDevice          3.5.1
com.apple.iokit.IOBDStorageFamily          1.7
com.apple.iokit.IODVDStorageFamily          1.7.1
com.apple.iokit.IOCDStorageFamily          1.7.1
com.apple.iokit.IOATAPIProtocolTransport          3.5.0
com.apple.iokit.IOSCSIArchitectureModelFamily          3.5.1
com.apple.iokit.IOFireWireFamily          4.5.5
com.apple.iokit.IOUSBUserClient          5.0.0
com.apple.iokit.IO80211Family          500.15
com.apple.iokit.IONetworkingFamily          3.0
com.apple.iokit.IOAHCIFamily          2.2.0
com.apple.iokit.IOATAFamily          2.5.1
com.apple.iokit.IOUSBFamily          5.1.6
com.apple.driver.AppleEFIRuntime          1.6.1
com.apple.iokit.IOHIDFamily          1.8.0
com.apple.iokit.IOSMBusFamily          1.1
com.apple.security.sandbox          220
com.apple.kext.AppleMatch          1.0.0d1
com.apple.security.TMSafetyNet          7
com.apple.driver.DiskImages          344
com.apple.iokit.IOStorageFamily          1.8
com.apple.driver.AppleKeyStore          28.18
com.apple.driver.AppleACPIPlatform          1.6
com.apple.iokit.IOPCIFamily          2.7
com.apple.iokit.IOACPIFamily          1.4
com.apple.kec.corecrypto          1.0
Model: iMac8,1, BootROM IM81.00C1.B00, 2 processors, Intel Core 2 Duo, 3.06 GHz, 2 GB, SMC 1.30f1
Graphics: NVIDIA GeForce 8800 GS, NVIDIA GeForce 8800 GS, PCIe, 512 MB
Memory Module: BANK 0/DIMM0, 1 GB, DDR2 SDRAM, 800 MHz, 0x2C00000000000000, 0x38485446313238363448445A2D3830304531
Memory Module: BANK 1/DIMM1, 1 GB, DDR2 SDRAM, 800 MHz, 0x2C00000000000000, 0x38485446313238363448445A2D3830304531
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8C), Broadcom BCM43xx 1.0 (5.10.131.36.16)
Bluetooth: Version 4.0.9f8 10405, 2 service, 18 devices, 1 incoming serial ports
Serial ATA Device: WDC WD5000AAKS-40YGA1, 500.11 GB
Parallel ATA Device: MATSHITADVD-R   UJ-875
USB Device: Built-in iSight, apple_vendor_id, 0x8502, 0xfd400000 / 2
USB Device: BRCM2046 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0x1a100000 / 2
USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x820f, 0x1a110000 / 5
USB Device: IR Receiver, apple_vendor_id, 0x8242, 0x5d100000 / 2
USB Device: Hub in Apple Extended USB Keyboard, apple_vendor_id, 0x1002, 0x1d100000 / 2
USB Device: Trackball, 0x046d (Logitech Inc.), 0xc404, 0x1d120000 / 4
USB Device: Apple Extended USB Keyboard, apple_vendor_id, 0x0204, 0x1d110000 / 3

My macbook pro will only boot in safe mode

Hey,
I have a macbook pro 15-inch, Early 2011 running osx 10.9.4. I have a SSD hard drive that i installed myself a year ago and hasn't shown any defects. Its a 120 gb OCZ-AGILITY3.
My problem:
My macbook will only boot in safe mode nowadays. I have done a complete erasion of my hard drive and installed osx mavericks twice already. After the installation the computer will safely go to the desktop. But if i then do a reboot it won't get further than after the first apple logo, sometime the turning wheel will pop up, before turning off and trying again. i have tried resetting PRAM, I have tried resetting SMC, i have tried avoiding SMC (with big fan rate), but all with no success.
I have done a complete hardware test (the longer one) and it showed "no troubles found".
My guess is that the problem is with the battery. My computer won't run anymore without the adapter, when i pull the adapter out it either stays on for a while before just turning off. Without having it plugged in it won't start. Is it possible that during normal start up there is some kind of communication with the battery that can cause this?
I ran a diagnostic shown in this thread (Will only boot in safe mode) and included it in this post.
Hope someone can help me out.
Thanks,
Bram
Start time: 17:07:42 08/25/14
Model Identifier: MacBookPro8,2
System Version: OS X 10.9.4 (13E28)
Kernel Version: Darwin 13.3.0
Boot Mode: Safe
Time since boot: 10 minutes
Battery
Condition: Replace Now
Diagnostic reports
2014-08-25 UserEventAgent crash
Log
Aug 26 00:41:52 Previous Shutdown Cause: -128
Aug 25 16:23:38 smb1_treeconnect_internal: Malformed tree connect with a bad word count! wc= 2
Aug 25 16:24:05 process rpcsvchost[94] thread 917 caught burning CPU! It used more than 50% CPU (Actual recent usage: 99%) over 180 seconds. thread lifetime cpu usage 100.014147 seconds, (82.533432 user, 17.480715 system) ledger info: balance: 90006319931 credit: 100003230498 debit: 9996910567 limit: 90000000000 (50%) period: 180000000000 time since last refill (ns): 90079246240
Aug 25 16:25:50 smb1_treeconnect_internal: Malformed tree connect with a bad word count! wc= 2
Aug 25 16:58:05 jnl: b(1, 3): replay_journal: from: 9340928 to: 9773056 (joffset 0x37a000)
Aug 25 16:58:05 jnl: b(1, 3): examining extra transactions starting @ 9773056 / 0x952000
Aug 25 16:58:05 jnl: b(1, 3): txn starting at 9773056 (9773056) @ index 80 bnum 2696544 (8192) with disk cksum != blhdr cksum (0x93b69228 0xc647562)
Aug 25 16:58:05 jnl: 0x662b0000 0x451b0000 0x2a0001ff 0x40000000 0xd7330300 0x46001d00 0x6c006f00 0x65006400
Aug 25 16:58:05 jnl: b(1, 3): restarting journal replay (9340928 - 9773056)!
Aug 25 16:58:05 jnl: b(1, 3): replay_journal: from: 9340928 to: 9773056 (joffset 0x37a000)
Aug 25 16:58:05 jnl: b(1, 3): journal replay done.
Aug 25 16:58:06 Previous Shutdown Cause: -128
Aug 25 16:59:26 smb1_treeconnect_internal: Malformed tree connect with a bad word count! wc= 2
Aug 25 16:59:59 smb1_treeconnect_internal: Malformed tree connect with a bad word count! wc= 2
Activity
CPU: user 17%, system 4%
CPU per process: WindowServer (UID 0) is using 30.5 %
launchd
/System/Library/LaunchAgents/com.apple.AirPortBaseStationAgent.plist
- com.apple.AirPortBaseStationAgent
Contents of /System/Library/LaunchAgents/com.apple.AirPortBaseStationAgent.plist (XML document text)
<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">
<plist version="1.0">
<dict>
<key>Label</key>
<string>com.apple.AirPortBaseStationAgent</string>
<key>EnableTransactions</key>
<true/>
<key>LowPriorityIO</key>
<true/>
<key>LimitLoadToSessionType</key>
<string>Aqua</string>
<key>POSIXSpawnType</key>
<string>Background</string>
<key>LaunchEvents</key>
<dict>
<key>com.apple.distnoted.matching</key>
<dict>
<key>com.apple.airport.agent.prefschanged</key>
<dict>
<key>Name</key>
<string>com.apple.airport.agent</string>
</dict>
</dict>
<key>com.apple.bonjour.events</key>
...and 21 more line(s)
Spotlight: Indexing and searching disabled
Font issues: 11
Wi-Fi
link auth: wpa-psk
Restricted files: 1
Elapsed time (s): 278

Actually it sometimes gets a little further, the display will dim and the pointer will appear and then whoop it will turn off. if i do a verbose start up, it will finish all the steps, the white screen will appear and dim and then it will turn off.

Qosmio X305 will only boot in safe mode or when the graphics card disabled

Hi All
I am having a very concerning issue with my laptop (Toshiba Qosmio X305). It will only boot in safe mode or if I disable the graphics card.
Awhile back I upgraded the drivers for the nVidia 9800M GTX from the nVidia website, it worked fine for awhile, but then it started crashing randomly by giving me a full screen of random color then switching off. I fixed this by rolling back to the previous version of the drivers (the drivers that came with the laptop software).
After that it working perfectly for months but yesterday my machine started crashing and I could not get it to boot correctly.
I have completely deleted (not just a quick format) both the hard drives that came internally in the laptop and I have installed a clean version (the out of the box option) of the x64 Vista that came with the laptop from the recovery disks I created. After I did the install, it boots fine as only the standard VGA device is used, as soon as I installed the driver off the drivers and applications disk it would not boot correctly:
Just after the status bar comes up and it is about to show the windows logo, just before login, I get a black screen. I can hear that it is booting fine and I can even log in to windows and by memory make things run, but I can't see anything. I then got the latest drivers, again from the nVidia website and they are not helping at all.
My system is as follows (nothing has been added, its is just how I got it):
Vista Ultimate x64
4.00 GB RAM
Intel Core 2 Quad
Like I said previously it is a clean install of the operating system, I have not added any programs, except for installing and then updating the display drivers.
Any help would be much appreciated!

Hi buddy,
It seems that this is a typical example, that only pretested display drivers from Toshiba should be used. Why?
The nVidia drivers are not pretested and they dont have an overheat protection. So for me it sounds like that the nVidia driver has destroyed your graphic card. That means no driver will help you and reinstallation of the whole system too.
I think the only option is replacing the graphic card. Therefore you should contact an authorized service provider in your country. Here you can search:
http://www.csd.toshiba.com
Explain the whole story and then you will see, what the technicians say. If your notebook is under warranty, hopefully this will be covered too. Normally other display drivers you have to install on your own risk
Good luck! :)

My Mac Pro 2.8 crashed and will not reboot in Safe Mode - HELP!

Hello
I have a Mac Pro 2.8 and it froze up on me; I held in the power button to shut it down. Upon restart, all I get is a flashing foldoer file icon with a question mark.
What gives? It will not start in Safe Mode, via the Shift button OR DOS command (sudo nvram boot-args="-x")
1. How do I get it back up? I have a back up on my external hard drive, but it doesn't recognize it?
2. Are all my current files gone?
Thanks for your help

A flashing question mark on boot can mean several things. One, your Mac can't find a system folder to boot from or the startup disk is failing or failed.
Since you don't have the install discs now, it may take some time to order and receive them from Apple. Probably time to take the Mac to an Apple Store or Apple certified repair shop. They can tell you for certain whether or not the disk has failed.
Since holding down the Option key that prompts the Startup Manager window didn't work, not does your external drive recognized your Mac, I'm afraid without a backup to restore those files from, you may be out of luck.
can I get a new one from mac, and will it erase all my files?
You can get replacement System Install & Restore CD/DVDs from Apple's Customer Support - in the US, (800) 767-2775 - for a nominal S&H fee. You'll need to have the model and/or serial number of your Mac available.

My aperture library will not open after restoring my whole computer after a kernal panic. I can not get the Aperture troubleshooting menu to open...any help?

My aperture library will not open after restoring my whole computer after a kernal panic. I can not get the Aperture troubleshooting menu to open...any help?

Leonie,
Fisrt let me thank you for your reply and assistance! So here is the problem with so more detail...I was not sure I was going to get any replies ; )
I restored from a time machine back up.
History of Failure:
I was trying to launch Aperture when the kernal panic occured. My computer had been closed, and asleep and the battery was dead. I plugged in charger and it was restoring/waking up after being asleep/shutting down from dead battery. I launched Aperture from the dock and as soon as it opened the kernal panic occured. After that the computer would not turn on. It would try to boot then it would shut off. I even tried to safe boot to no avail. I went to the Apple store and they told me that the only thing I could do was restore whole computer from back up. So thats what I did.
Since then my previous aperture library: "2011" will not open. I have created a new aperture library "2012", and it runs fine. I have added new photos for about the past month...no problems.
When I launch aperture with 2012 library then try to switch libraries, I get the following prompt: "The selected library is from an older version of Aperture and requires a relaunch to switch." I choose "Relaunch" and I get the following warning prompt: "There was an error opening the database for the library “~/Pictures/Aperture Library 20111.aplibrary”." The only option is "Quit"
Both libraries are version 3.2.3
Computer stats: 3.06 GHz Core 2 Duo, 8 GB 1067 MHz DDR3 RAM, OS X 10.6.8
I have tried to launch aperture troubleshooting by holding option+command from both the aperture icon and from the library file, neither will launch the troubleshooting feature.
I am ok with computers, but not a whiz (mechanical engineer)...to me it seems as though there is a corrupt path or file or some sort of "check" that is failing, becuase the failure occurs so fast after trying to launch aperture. Maybe that doesn't make any sense but just a thought.
I hope that you may be able to provide some insight. Thank you again for you time and I hope that you have a nice day!
Mike

I have no navigation bar and firefox will not open in safe mode to reset to default config. Reinstalling doesn't work. Any help please.

I have no navigation bar ever since I closed it to gain more space on the screen. It won't re-open. Firefox will not open in safe mode, but opens immediately in normal mode with the new improper config, so I cannot reset to default config. I erased Firefox and re-installed and it still opens with the same faulty config. Why does Firefox not give me the safe mode dialog box, why can I not re-open the nav bar, and how can I do these two things, please? Firefox is currently unusable for me without a nav bar and without access to the default settings in safe mode. I cannot research the extensions I'm running since I have no nav bar to go to Tools, Add-ons, Extensions.
== This happened ==
Every time Firefox opened
== I closed the navigation bar to gain more space on the screen and I couldn't re-open it. ==
== User Agent ==
Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.1; Trident/4.0; GTB6.4; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; Media Center PC 6.0)

Hit the '''Alt''' key to show the Menu bar, then open View > Toolbars and select Menu bar and Navigation bar, so they have a check-mark.

How can I transfer files from a 27" iMac which will only boot in safe mode?

My late 2009 27" imac is having issues and will only boot in safe mode. I have tried to transfer files to a new Imac using migration assistant but it wont let me. If I try booting the old Imac normally I just get a grey screen, I believe it is the video card failed and am waiting for a fix, but I would like to transfer files before the fix in case something goes wrong and I lose everything.
Any help would be great

Hello Myles, likely it is a Hardware problem.
One way to test is to Safe Boot from the HD, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, Test for problem in Safe Mode...
PS. Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive
Reboot, test again.
If it only does it in Regular Boot, then it could be some hardware problem like Video card, (Quartz is turned off in Safe Mode), or Airport, or 3rd party add-on, Check System Preferences>Accounts>Login Items window to see if it or something relevant is listed.
Check the System Preferences>Other Row, for 3rd party Pref Panes.
Also look in these if they exist, some are invisible...
/private/var/run/StartupItems
/Library/StartupItems
/System/Library/StartupItems
/System/Library/LaunchDaemons
/Library/LaunchDaemons

Firefox crashes when opening and will not open in safe mode

Recently FF3 started crashing when opening. It will not open in safe mode as well. I have uninstalled it including deleting the install folder and profile folders as well as registry entries. Upon reinstallation is will still not launch in any mode.
I have scanned for malware with several scanners and that has not found anything.
Here is the crash report cause - nsCOMPtr_base::~nsCOMPtr_base() | nsDocShell::SetupNewViewer(nsIContentViewer*)
Anti-virus is Trend Micro Worry Free for Business. I uninstalled it and Firefox and then reinstalled only Firefox and still get the same thing.
I do not know what to try next.

Add-ons: {972ce4c6-7e08-4474-a285-3208198ce6fd}:3.6.3
BuildID: 20100401064631
CrashTime: 1274739594
EMCheckCompatibility: true
Email: [email protected]
FramePoisonBase: 00000000f0dea000
FramePoisonSize: 4096
InstallTime: 1274097386
ProductName: Firefox
ReleaseChannel: release
SecondsSinceLastCrash: 525200
StartupTime: 1274739562
Theme: classic/1.0
Throttleable: 1
URL: http://en-us.start3.mozilla.com/firefox?client=firefox-a&rls=org.mozilla:en-US:official
Vendor: Mozilla
Version: 3.6.3
This report also contains technical information about the state of the application when it crashed.

Outlook 2013 in a 2012 r2 Terminal Server environment and crashes after initial setup. It will not launch in safe mode

I am running terminal server 2012 R2 (RDS environment) In Windows Domain, 8 users across a LAN on a new server. Outlook 2013 crashes and will not load in safe mode. Outlook allows the initial profile setup and when the configuration is complete, it
crashes and will not launch or launch in safe mode. I have deleted the outlook profile and reconfigured it. The problem continues on all user accounts. The firm is not using Exchange and is using a POP3 account. I have a 13 user Office Volume License
(per device) and 15 terminal server Licenses ( per user)
Problem Event Name :      APPCRASH
Application Name:            Outlook.EXE
Application Timestamp :   52b0b282
Fault Module Name :        OUTLOOK.EXE
Fault Module Version :     15.0.4569.1503
Fault Module Timestamp: 52b0b282
Exception Code:                 C0000005
Exception Offset:                00340b9
OS Version:                      6.3.9600.2.0.0.16.7
Local ID :                         1033
Any help would be much appreciated.

follow this instruction to troubleshoot Outlook crash issue:
http://support.microsoft.com/kb/2652320
Flynn

13 inch mid 09 MBP will not boot in safe mode or os disc. originally kernal panic but now blank screen. is this logic board? no liquid damage.

Similar Messages

Maybe you are looking for