1300 bridge with native and management vlan in different vlans

Hello,
We are going to set up a wireless bridge between two 1300 accesspoints. In our network the native vlan and the management vlan are different vlan's. Will we be able to manage the ap and switch at the "remote" site? Do we have to set up two ssid's, one for native and one for management?
regards,
Rutger

Too answer my own question:
I don't think it is possible. Things work fine by making our management vlan the native vlan on switches and ap's involved. Management IP address on the BVI1 interface and everything works!
Rutger

Similar Messages

Creating Weblogic domain with Admin Server and managed servers on different

I am trying to create Weblogic domain where Admin Server and managed servers on different machines. However I am unable to find any steps which would allow me to do so. The config.sh script always creates an Admin Server. Please help.

Whilst the method that Lawrence gives can result in a domain that is perfectly functional, it is a method that can result in errors as you are having to enter the same information twice. Also you will create two admin servers, as the second domain creation will have the console added to it on the renamed admin server and this will give issues.
The best method to create a domain spamming multiple physical machines, is to create the domain with all the components on the first machine. This means planning the domain and making sure all components are added once; so having the information about the domain written out is wise. Ensure that the WLS software is installed in the same path on each machine before starting.
Then copy the domain that you have created from one machine to the other, keeping the same paths. You can simply copy (I've used this method multiple times without issue) but the supported way would be to use the WLST PACK and UNPACK methods. These create and extract domains from templates. Some more information on these is given here -> http://docs.oracle.com/cd/E13179_01/common/docs100/pack/intro.html#wp1069056

VLANs - Default, Native and Management

Okay, please help in understanding the concept of VLANs by confirming whether the following is true or not, and based on that please help me to clear my doubts.
Default vlan - Always Vlan 1 on a switch and cannot be changed. It's purpose is to account the interfaces/ports which are not assigned with a vlan explicitly.
Native vlan - By default, it is also vlan 1 in a switch, but can be changed. Frames belonging to the native vlan are sent across the trunk link untagged. It's sole purpose is to provide back ward compatibility to the devices that doesn't understand frame tagging, as per 802.1q.
Management vlan- for managing switches.
Now my doubts ::
1. Can anyone please draw and explain a scenario in which NATIVe vlan comes into use, so that I can understand its purpose completely.
2. Management vlan- how they are created/assigned and is used ?

Hello
From a security perspective its best practice to not use vlan1 whatsoever as it well documented that all cisco switches default to this vlan.
Also it is best to define a native vlan that will be not used.
This is due to something I think is called ( double tagging or vlan hopping) - and it when a hacker knowing that vlan 1 is untagged and the default vlan can apply an outer tag to a encapsulated packet and send this into your network, then when this outer tag is stripped away the native vlan1 is seen by the switch which is excepted into your network.and sent on its merry way toward its destination.
So to negate this threat it is best to either tagged ALL vlans or define a unused native vlan and a tagged management vlan and not allow the native vlan to cross any trunks
example:
vlan 1 = shutdown
vlan 10 = management
vlan 11-49 - user vlans
vlan 50 = native
conf t
vlan 2-50
exit
int vlan 1
shut
int vlan 10
ip address x.x.x.x y.y.y.y.y
interface gig x/x
switchport trunk encapsulation dot1q
switchport trunk native vlan 50
switchport trunk allowed vlan 2-49
res
Paul

Nokia E50, issues with connecting and managing mes...

Hi
I'm using Nokia E50 and Nokia PC Suite for a few years now on. Recently I wanted to do my usual maintenance task: copy all messages to PC and delete them from the phone. Issues start here.
At first I had problems with connecting but finally I manage to do it. After dozens of tries PC Suite finally updated contact list. Then I moved to messages tab. It took a while to download all messages (aprox. 700 in inbox, 600 in sent - I had many more few times before when everything was working ok). I can copy them to PC, but I can't delete them. After selecting message(s), trash icon is grayed out (menu item too). I can read message but can't delete it. Why?
I've downloaded latest version of Ovi to see if that would help. Ovi managed to download contact list (after a loong waiting) but failed to download any message. Messages says that it's trying but after one hour nothing happend.
I'm trying this on 2 different machines (Windows 7 and Windows XP), with cable and blue tooth. Efects are always the same. Phone is connected because I can copy files, but when I'm trying to download messages or do backup, software says phone is not connected or tries to copy data with no luck.
Any hint will be appreciated.
Thanks
Marooned

After deleting aprox. 150 messages from Inbox and from Sent, both programs were able to download complete list of messages and PC Suite finally reenabled trash icon.
Seems like too much messages causes those program to fail? And why in the past they were working properly with bigger amount of messages?
Well.. one can say "problem solved" but will reappear again in the future with lots of messages. I need to remember to grab them from the phone more frequent.

Can I run the admin and managed servers as different users?

in unix, is it possible to run my admin and manged servers as different users with
7.1?

As long as users are in admin group, there could be different users starting different
servers.
"Frank" <[email protected]> wrote:
>
"Erik Johnson" <[email protected]> wrote:
Hi, Frank.
Could you be a little more specific about what it is you want to do?
Thanks.
erikUh, I'm on unix, I have Weblogic 7.0 service pack4. I have 1 managed
server and
I have one admin server...Can I run the admin server as user 'hithere'
and run
the managed server as user, 'byethere'......
"Frank" <[email protected]> wrote:
in unix, is it possible to run my admin and manged servers as different
users with
7.1?

PDF with Portait and Landscape Orientation act differently between pages

Hi,
I have issue when I'm trying to have a landscape orientation in a PDF with another portrait page.
All I want to do is have a small page which indicates instructions on the form because it is a form builder, once the form is created by the user the landscape page gets hidden.
My issue here is that when I set a masterpage to landscape it makes it different to switch between pages.
I can't see more than 1 page at a time, just like it can't show a landscape and portait orientation together in the screen.
I have another form with landscape and portait together and it works fine, but this form doesn't stay normal... There must be something I'm missing...
It is annoying that I can't have more than one page in the screen, once I hit the bottom or the top of the page it switches automatically to the other page.
Please help me on this, I'm trying to figure out what is causing this bug..

Hi,
I haven't used form builder, but do you still have a viewState, try adding the following line in the docReady event of the form
event.target.viewState = { pageViewLayoutMode:2 };
This has the same effect as setting Enable Scrolling on the View ... Page Display menu.
A value of 1 would give you the single page view.
Regards
Bruce

FCP7 HELP - Exported quicktime mov plays differently than what I edited on the timeline. The playback shows the clips with ins and outs that are different than what I set in the clips when I edited - some are too early and the clips don't playback

Please help ASAP.
Specs: IOS 10.6.8
Processor 2.4GHz Intel Core i5
Memory 4GB 1333 MHz DDR3 -- Everything is edited, sourced, and stored on an 2TB external hard drive to make things go faster.
Editing with FCP 7
When I export the sequence I edited with quicktime, the playback video is very different from what I edited on the timeline. The playback has the clips with ins and outs that are way off than what I cut, and some of the clips don't show at all or have changed transitions. However when I play in the timeline in FCP, the sequence is fine, just the way I cut it.
The source of the clips was one long .mov that I cut into clips for the timeline. Everything has gone smoothly but the exported .mov is just so different.
How can I get the time codes of the clips to be the same in the exported .movs? I just want the quicktime .mov to represent my edit exactly.
This video is due tomorrow - if the solution is too time consuming, can I play within the FCP player window and Log and Capture?
Thanks,
MV

What is your source material? Is it H.264? FCP does not work correctly with that material.
Click on a source clip in the FCP Browser, and once selected, type Command + 9 to see the item properties for the clip. Either report those properties, or take a screen shot of the item properties, and post that here.
Next, click anywhere in your timeline, and then type Command + 0 {zero} to see your Sequence Settings. Either report those Sequence Settings, or take a screen shot of the Sequence Settings and post that here.
MtD

MOBI with BOE and mobile server on different servers

Hi Experts,
We need to set up a BO MOBI with BOE and Mobile server on two separate servers.
In such a configuration, how does the two servers communicate?
What should be the VAS and VMS server configurations? especially the external hostnames in the files?
We are looking for a non Blackberry(proxy) deployment.
We have installed the software,however the windows services of Authserver and the Job servers are not available in the mobile server instance
Any help would be highly appreciated.

I figured it out. I had to re-run the schconfig utility on UNIX and reconfigured the server from localhost:9710 to the actual server name.

AP with EAP and managment control through ACS

I have deployed a number of wireless networks with EAP authenticated through the users domain account details passed to ACS 4.1. This appears to work fine, but I have two questions regarding control of access.
1. I have configured RADIUS for the EAP and then added TACACS+ for the management access of the AP. Although going back to the same ACS server with different protocols I am unable to get the managment access control to work if both are active? Should this work?
2. How do I control which VLAN / SSID a user has access to? it seems as though there is no way to limit them to a specific SSID (other than not telling them it) If the users have a guess at the SSID then the possibility is that they can access a LAN they should not.
Any help would be very greatfully received.

Hi ihill,
in answer to your second question there is a couple of ways that you can do this depending on the amount of control you have over your clients.
You could use dynamic VLAN assignment:
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml
You could use Active Directory wirelss group policy to define prefered wirless networks for your clients
Or you could use a 3rd party supplicant like the Juniper Network's Odyssey Access Client
http://www.juniper.net/products_and_services/aaa_and_802_1x/odyssey/odyssey_access_client/
hope this helps
Mark
*pls rate all useful posts

E4200 Bridged Mode - Wireless and Management fail after 36 hours

Greetings all,
I am trying to see if anybody else is having this problem. I have the E4200 and have it configured in bridged mode. Once configured, everything works great for 36 hours.
After 36 hours, all wireless devices are unable to pull an IP address and the management IP address of the E4200 stops responding. The only way to restore service is to reload the router.
I took the first one back to Best Buy and they gave me a new one, however the new router has the same issue.
It seems to me that after 36 hours, the E4200 fails to renew its management IP and also stops forwarding wireless broadcasts (DHCP) requests to my DHCP server.
Thoughts?

Thanks. The new E4200 firmware has "bridged mode" so basically I just have this thing acting as a Wireless access point that has 5 Gigabit ethernet ports.
This disables the routing engine in the E4200 and it acts as a wireless AP and switch. The E4200's WAN port then connects to a Gigabit switch located in my telco closet, which is connected to my FiOS Router.
Reason for this setup is so that devices connected to either the Gigabit switch, or to the E4200 via hardwire or wireless will all remain on the same subnet, and not cause the broadcasts to block as packets traverse subnets.

Bridging with AP1030 and Controller

Hi
I have a test enviroment with 2 ap1030 and i want to make a 5ghz bridge link with these two aps. this should be possilbe. but im not able to get it worked. i also didnt found a good documenation for this configuration.
do i need to make both aps in BRIDGE mode?
in the debugging i always get: LWAPP Join-Request AUTH_STRING_PAYLOAD, invalid BRIDGE key hash AP 00:0b:85:71:cd:a0
when i connect the "BRIDGE" ap to the lan. i set a key under zero touch config, and also tried to RESET the ap. doesnt work
anybody can help?
regards

It's pretty simple, just not well documented.
1. First, write down the macs of each AP, and connect them so they are both assoicated to the controller.
2. Enable Zero Touch Config on your controller
3. Goto the Security Page, under AAA on the left side, click on MAC Filtering.
4. Add a Mac Filter for each of the AP's Macs (Which you already wrote down)
5. Goto the Wireless Page. Select Detail on one of the APs. Change it from Local Mode to Bridge AP
and hit APPLY. The AP should reboot.
6. Repeat this step with the Other AP.
7. Once both AP's have rebooted, and reassoiated, and you have confirmed they are both in Bridge AP mode, you can unpluge one of them. Just apply power, and it should setup the AP bridge.
8 IMPORTANT You cannot do this from WCS (I've never seen the option there)
From the AP details screen, select Ethernet Bridging (check the checkbox) on BOTH of the bridges.
You should be able to plug a client into the RJ45 of your remote bridge, and pass traffic now.
THIS Step is only nessacary if you entend to use the ethenet interface on the remote AP.
If you continue to have problems, you can try this: (Try the above first, since I don't think you created the MAC Filter, which YOU MUST do)
From controller CLI "config network allow-old-bridge-aps enable"

Populating a dynamic array with objects and managing it in runtime.

So I'm another stuck firstyear. I'll try and make my question compact. I'm using Flash CS6 and have drawn an animated character on the stage that consists of separate parts that are animated and its head is a separate class/symbol entirely because it has not only animation, but a state switch timeline as well. This said Head extends the Main that is the character MovieClip.
I am using a dynamic array to store and .push and .splice objects of another class that would collide with this said Head.
I also discovered the super() function that is implicitly called as the constructor of the parent in any child class that extends the parent, in this case Head extends Main. The issue is that my collidable object array is populated within the main, within the function that spawns every next collidable object with a TimerEvent. This said function then gets called twice due to the super() call.
I have tried putting this super() call into an impossible statement in my child class, but it doesn't change a thing, and it was said that this method is unsafe so I don't even know if it should be working.
However what confuses me the most is when I trace() the .length of my collidable object array at the end of that function. As I said earlier, the original function both spawns an object after a period of Timer(1000) and adds it to the stage as well as adds the object onto the object array, but the super() constructor only duplicates the length call and a creates a copy of the object on the stage, but it does not add the second copy of the object onto the array. The trace() output goes on like so:
1
1
2
2
3
3
4
4
etc.
I wonder why and I'm really stumped by this.
Here is the code in question:
public class Main extends MovieClip {
                    public var nicesnowflake: fallingsnow;
                    var nicesnowflakespawntimer: Timer = new Timer(1000);
                    public var nicesnowflakearray: Array = new Array();
                    public function Main() {
                              nicesnowflakespawntimer.addEventListener(TimerEvent.TIMER, nicesnowflakespawn);
                              nicesnowflakespawntimer.start();
                    public function nicesnowflakespawn(event:TimerEvent) : void {
                              nicesnowflake = new fallingsnow;
                              nicesnowflake.x = Math.random()* stage.stageWidth;
                              nicesnowflake.y = - stage.stageHeight + 100;
                              nicesnowflakearray.push(nicesnowflake);
                              stage.addChild(nicesnowflake);
                              trace(nicesnowflakearray.length);
                              for (var i:Number = 0; i < nicesnowflakearray.length; i++){
                                        nicesnowflakearray[i].addEventListener(Event.ENTER_FRAME, snowhit);
                    public function snowhit(event:Event) : void {
                              if (nicesnowflakearray[0].y >= 460){
                                        if (nicesnowflakearray[0].y == stage.stageHeight) {
                                        nicesnowflakearray.splice(nicesnowflakearray.indexOf(nicesnowflake), 1);
                              //if (this.hitTestObject(nicesnowflake)){
                                        //trace("hit");
I am also fiddling with the collision, but I believe that it would sort itself out when I deal with the array pop and depop properly. However I'm pasting it anyway in case the issue is subtly hidden somewhere I'm not looking for it. And here is the child class:
public class Head extends Main {
                    public function Head(){
                              if (false){
                                        super();
                              this.stop();
So like what happens at the moment is that the array gets populated by the first object that spawns, but there is two objects on the stage, then when the objects reach stage.460y mark the array splices() the one object away and displays an error:
"#1010: A term is undefined and has no properties.
          at Main/snowhit()"
then when the next object spawns, it repeats the process. Why does it trace the array.length as "1, 1, 2, 2, 3, 3, 4, 4, 5, 5, etc" until the despawn point and then goes on to display an error and then starts from 1 again, because if the array length is more than one object at the time when the first object of the array gets spliced away, shouldn't it go on as usual, since there are other objects in the array?
Thank you very much to whomever will read this through.

There are multiple problems:
1. You should add eventlisteners for your objects only once, but you add eventlisteners every time your timer runs to all of your snowflakes, again and again:
                              for (var i:Number = 0; i < nicesnowflakearray.length; i++){
                                        nicesnowflakearray[i].addEventListener(Event.ENTER_FRAME, snowhit);
change it to
nicesnowflake.addEventListener(Event.ENTER_FRAME, snowhit);
I don`t see why its even necessary to employ this snowflakearray, it would be much straight forward if you simply let the snowflakes take care of themselves.
2. Then you have to change your enterframe function accordingly
public function snowhit(event:Event) : void {
                              if (e.currentTarget.y >= 460){
                                        if (e.currentTarget.y == stage.stageHeight) {
                                        e.currentTarget.removeEventlistener(Event.ENTER_FRAME, snowhit);
                                        removeChild(e.currentTarget);
3.
                              //if (this.hitTestObject(nicesnowflake)){
                                        //trace("hit");
since "this" is a reference to the Main class (root) it surely won`t function as you intend it to.
                              if (false){
                                        super();
makes no sense to use a condition that can never be true

WDS Bridging with EPC2425 and EPC3925

I have a redundant Cisco EPC2425 that I want to use as a wireless bridge to connect to my current home router (an EPC3925).
I have got the channels/band/keys matching yet the 2425 is failing to connect to my home router. I have set the 2425 in bridge mode and currently can only set the wireless properties.
I have both ends of the supposed bridge referencing the other's MAC.
When I try to enter advanced settings on the 2425 I get a notice that the function has not been enabled.
What can I try to get these two boxes talking to each other?
Thank you.

Sam:
I only can help by providing the user guide for your device:
http://www.comhem.se/blob/view/-/14442/data/4530/-/manual_cisco.pdf.pdf
I can only see that you enable bridging and provide the other mac address/addresses your bridge should connect to. Nothing else.
Actually this section in the forum is not the one for your device.
You better put your question here: https://supportforums.cisco.com/community/netpro/small-business/wireless
Good luck
Amjad

PXE boot issue with DHCP and SCCM server on different subnets

I'm working with a client on the operating system deployment module of SCCM.
Their network configuration currently has a single large subnet for client
computers with a DHCP server on the same subnet. The SCCM subnet is
configured on a seperate subnet with no DHCP server on the subnet. We want to
configure client computers to be able to boot using the PXE client to deploy
OS images to the machines but can not get PXE-boot to work correctly.
Also, the client does not want to make changes to their network
infrastructure routers or switches to remedy this problem. Are there settings
on the DHCP or SCCM servers we can implement to make this work? If so, what
needs to be installed or configured on each server. We currently already have
WDS installed on the SCCM server and the SCCM server is configured as a PXE
Service Point within SCCM. Both WDS and the PXE Service Point seem to be working fine.
Any help would be appreciated.
Thanks,
Gary

I am Brazilian,
sorry for wrong english
My DHCP is on linux,
in my own structure VLANS
The system center is on the network
10.0.4.0/24
The machines on the network 10.0.5.0/24
The problem is that the machines that
are not on the same network system center
can not boot
I tried configuring / etc/dhcp3/dhcpd.conf
follows
option vendor-class-identifier "PXEClient";
option bootfile-name "\
\ SMSBOOT \ \ x86 \
\ wdsnbp.com";
option tftp-server-name
"10.0.4.101"; ---->
IP server
But it did not work, anyone know
how to configure?

IOS AP; need to have 2 management IPs ind different VLANS. Possible?

We have the need to add a "secondary" Management IP due to a IP rearrangement.
Ist this possible?
If yes, how?
Thanks,
Peter

I'm not sure why you would need a second IP on an autonomous AP. The IP on the AP is just used for managmenet of the AP and other mgmt type tasks like sending EAPOL packets to the radius server, responding to SNMP, etc. As far as the subnet info for the wireless clients, the AP really doesn't care. Its just bridging the packets through the AP.

1300 bridge with native and management vlan in different vlans

Similar Messages

Maybe you are looking for