1310 Bridge Associated but cannot send/receive data

Question

Hi everyone,
I've just setup in my office a pair of 1310 with external antennas and I'm trying to test the link by pinging the other side from each bridge, but it seems like it's failing as I can't get any data through the link.
I've doublechecked my configuration and everything seems ok.
Below is the configuration:
Root Bridge:
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname root
enable secret xxx
no aaa new-model
dot11 ssid ip-mon
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 12345
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm tkip
ssid ip-mon
speed basic-1.0 basic-2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0
packet max-retries 3 0 fail-threshold 100 500 priority 5 drop-packet
packet max-retries 3 0 fail-threshold 100 500 priority 6 drop-packet
no preamble-short
channel 2472
station-role root bridge
beacon dtim-period 10
world-mode dot11d country GR both
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.10.2 255.255.255.0
no ip route-cache
ip default-gateway 192.168.10.1
ip http server
ip http authentication local
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
snmp-server community community RO
bridge 1 route ip
line con 0
login local
line vty 0 4
login local
end
Non-Root Bridge:
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname non-root
enable secret xxx
no aaa new-model
dot11 ssid ip-mon
authentication open
authentication key-management wpa
guest-mode
infrastructure-ssid optional
wpa-psk ascii 7 12345
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm tkip
ssid ip-mon
speed basic-1.0 basic-2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0
packet max-retries 3 0 fail-threshold 100 500 priority 5 drop-packet
packet max-retries 3 0 fail-threshold 100 500 priority 6 drop-packet
no preamble-short
channel 2472
station-role non-root bridge
beacon dtim-period 10
world-mode dot11d country GR both
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.10.3 255.255.255.0
no ip route-cache
ip default-gateway 192.168.10.1
ip http server
ip http authentication local
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
snmp-server community community RO
bridge 1 route ip
line con 0
login local
line vty 0 4
login local
end
Any help or suggestions are welcome.
Thank you

Answer 1

I understand your reluctance to use the GUI to configure the AP but having worked with this product since it ran on VXWorks the GUI is the way to go because the CLI documentation falls a little short on this product when it comes to configuring anythisn but the IP address and WEP encryption. That is why I always reccommend using the the GUI for these configurations. With the GUI you can eaisly save the config file and reapply it to an AP, also as it is saved as a .txt file you can edit it to your hearts content in notepad or telnet to the AP and use the CLI to edit it in place.
I have seen to many config errors when the CLI is used when 5 minutes with the GUI resulted in a working AP.
I know the GUI works give it a try and check the resulting config file.
I'll get off my soap box
good day
Bill