1310 LAP unable to join WLC 5508
Hi All,
Hope to you a very happy new year,
I have an (AIR-LAP1310G-E-K9R) and I tried to join it to WLC 5508 but I'm facing an error,
I get this error from the LAP 1310 console as below:
Compiled Mon 17-Jul-06 11:45 by alnguyen
*Mar 1 00:00:05.289: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:06.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:23.337: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:33.477: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.114.36.25, mask 255.255.255.0, hostname APe4d3.f1c2.8882
examining image...
*Mar 1 00:00:44.781: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
*Jan 11 15:21:37.178: %LWAPP-5-CHANGED: LWAPP changed state to IMAGE
%Error opening (Protocol error)archive download: takes 6 seconds
*Jan 11 15:21:43.178: LWAPP_CLIENT_ERROR_DEBUG: Retransmission count for packet exceeded more than max(IMAGE_DATA
, 1)
*Jan 11 15:21:43.178: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Jan 11 15:21:43.179: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Jan 11 15:21:43.181: LWAPP_CLIENT_ERROR: not receive read response(3)
*Jan 11 15:21:43.185: lwapp_image_proc: unable to open tar file
*Jan 11 15:21:43.200: %SYS-5-RELOAD: Reload requested by lwapp image download proc. Reload Reason: Reason unspecified.
*Jan 11 15:21:43.201: %LWAPP-5-CHANGED: LWAPP changed state to DOWN
*Jan 11 15:21:43.207: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERYXmodem file system is available.
flashfs[0]: 3 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 7741440
flashfs[0]: Bytes used: 1861632
flashfs[0]: Bytes available: 5879808
flashfs[0]: flashfs fsck took 14 seconds.
Base ethernet MAC Address: e4:d3:f1:c2:88:82
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
Loading "flash:/c1310-rcvk9w8-mx/c1310-rcvk9w8-mx"...#######################################################################################################################################################################
File "flash:/c1310-rcvk9w8-mx/c1310-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1310 Software (C1310-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:45 by alnguyen
Image text-base: 0x00003000, data-base: 0x00359EA0
Initializing flashfs...
flashfs[1]: 3 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 7741440
flashfs[1]: Bytes used: 1861632
flashfs[1]: Bytes available: 5879808
flashfs[1]: flashfs fsck took 2 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
cisco AIR-LAP1310G-E-K9R (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
Processor board ID FGL1649T00U
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from reload
LWAPP image version 3.0.51.0
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: E4:D3:F1:C2:88:82
Part Number : 73-8960-09
PCA Assembly Number : 800-24963-06
PCA Revision Number : B0
PCB Serial Number : FOC16447J1K
Top Assembly Part Number : 800-28479-05
Top Assembly Serial Number : FGL1649T00U
Top Revision Number : D0
Product/Model Number : AIR-LAP1310G-E-K9R
Press RETURN to get started!
*Mar 1 00:00:04.329: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1310 Software (C1310-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:45 by alnguyen
*Mar 1 00:00:05.289: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:06.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:23.337: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:33.352: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.114.36.28, mask 255.255.255.0, hostname APe4d3.f1c2.8882
examining image...
*Mar 1 00:00:44.783: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
*Jan 11 15:21:37.189: %LWAPP-5-CHANGED: LWAPP changed state to IMAGE
%Error opening (Protocol error)archive download: takes 6 seconds
*Jan 11 15:21:43.189: LWAPP_CLIENT_ERROR_DEBUG: Retransmission count for packet exceeded more than max(IMAGE_DATA
, 1)
*Jan 11 15:21:43.189: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Jan 11 15:21:43.189: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Jan 11 15:21:43.192: LWAPP_CLIENT_ERROR: not receive read response(3)
*Jan 11 15:21:43.195: lwapp_image_proc: unable to open tar file
*Jan 11 15:21:43.210: %SYS-5-RELOAD: Reload requested by lwapp image download proc. Reload Reason: Reason unspecified.
*Jan 11 15:21:43.210: %LWAPP-5-CHANGED: LWAPP changed state to DOWN
*Jan 11 15:21:43.216: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERYXmodem file system is available.
flashfs[0]: 3 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 7741440
flashfs[0]: Bytes used: 1861632
flashfs[0]: Bytes available: 5879808
flashfs[0]: flashfs fsck took 14 seconds.
Base ethernet MAC Address: e4:d3:f1:c2:88:82
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
Please Advise,
Thanks in advanced,
Ahmed,
Dear Stefan,
Many thanks for your kind reply,
Please find the information below:
Controller Summary
Management IP Address
10.114.44.131
Service Port IP Address
10.114.23.20
Software Version
7.2.111.3
Field Recovery Image Version
6.0.182.0
System Name
CIR906.WLC.5508
Please Advise,
Thanks,
Ahmed,
Similar Messages
-
3602i CAP unable to join WLC 5508
Hi All,
Hope to you a very happy new year,
I have an (AIR-CAP3602i-E-K9) and I tried to join it to WLC 5508 but I'm facing an error,
I get this error from the LAP 1310 console as below:
Reading cookie from SEEPROM
Base Ethernet MAC address: 60:73:5c:ad:cb:9c
Boot CMD: 'boot flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx;flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx'
Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx"...#####################
File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx" uncompressed and installed, entry point: 0x2003000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C3600 Software (AP3G2-RCVK9W8-M), Version 15.2(2)JA, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Thu 23-Aug-12 02:43 by prod_rel_team
Initializing flashfs...
flashfs[2]: 6 files, 3 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 31997952
flashfs[2]: Bytes used: 7015936
flashfs[2]: Bytes available: 24982016
flashfs[2]: flashfs fsck took 9 seconds.
flashfs[2]: Initialization complete.
flashfs[3]: 0 files, 1 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 12257280
flashfs[3]: Bytes used: 1024
flashfs[3]: Bytes available: 12256256
flashfs[3]: flashfs fsck took 0 seconds.
flashfs[3]: Initialization complete....done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Warning: the compile-time code checksum does not appear to be present.
cisco AIR-CAP3602I-E-K9 (PowerPC) processor (revision A0) with 180214K/81920K bytes of memory.
Processor board ID FCZ1642J01K
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.3.1.73
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 60:73:5C:AD:CB:9C
Part Number : 73-14521-02
PCA Assembly Number : 800-37501-02
PCA Revision Number : A0
PCB Serial Number : FOC16352BJ0
Top Assembly Part Number : 800-35852-02
Top Assembly Serial Number : FCZ1642J01K
Top Revision Number : C0
Product/Model Number : AIR-CAP3602I-E-K9
% Please define a domain-name first.
logging facility kern
^
% Invalid input detected at '^' marker.
logging trap emergencies
^
% Invalid input detected at '^' marker.
logging facility kern
^
% Invalid input detected at '^' marker.
logging trap emergencies
^
% Invalid input detected at '^' marker.
Press RETURN to get started!
*Mar 1 00:00:10.355: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 1 00:00:11.971: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:12.575: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3600 Software (AP3G2-RCVK9W8-M), Version 15.2(2)JA, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Thu 23-Aug-12 02:43 by prod_rel_teamlwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:13.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:15.387: DPAA Initialization Complete
*Mar 1 00:00:15.387: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Mar 1 00:00:15.979: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
no bridge-group 1 source-learning
^
% Invalid input detected at '^' marker.
%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 00:00:32.327: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C2960S-48FPD-L (10bd.18a5.6082)
*Mar 1 00:00:48.579: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.114.42.204, mask 255.255.255.128, hostname AP6073.5cad.cb9c
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (10.114.44.129) (8.8.8.8)
*Mar 1 00:00:59.459: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.114.44.131 obtained through DHCP
*Mar 1 00:00:59.459: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:01:00.015: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:01:00.015: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'CIR906.WLC.5508'running version 7.0.235.3 is rejected.
*Mar 1 00:01:00.015: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:01:00.015: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:01:00.015: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:01:00.015: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.114.44.131
*Mar 1 00:01:10.015: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'CIR906.WLC.5508'running version 7.0.235.3 is rejected.
*Mar 1 00:01:10.015: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:01:10.015: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:01:10.015: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:01:10.015: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.114.44.131
*Mar 1 00:01:20.015: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'CIR906.WLC.5508'running version 7.0.235.3 is rejected.
*Mar 1 00:01:20.015: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:01:20.015: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:01:20.015: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:01:20.015: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.114.44.131
*Mar 1 00:01:30.015: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'CIR906.WLC.5508'running version 7.0.235.3 is rejected.
*Mar 1 00:01:30.015: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:01:30.015: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:01:30.015: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:01:30.015: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.114.44.131
*Mar 1 00:01:32.343: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C2960S-48FPD-L (10bd.18a5.6082)
*Mar 1 00:01:40.015: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'CIR906.WLC.5508'running version 7.0.235.3 is rejected.
*Mar 1 00:01:40.015: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:01:40.015: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:01:40.015: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:01:40.015: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.114.44.131
Not in Bound state.
*Mar 1 00:01:55.515: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:02:02.519: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Mar 1 00:02:02.555: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.114.42.205, mask 255.255.255.128, hostname AP6073.5cad.cb9c
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (10.114.44.129) (8.8.8.8)
*Mar 1 00:02:06.515: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.114.44.131 obtained through DHCP
*Mar 1 00:02:06.515: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:02:06.631: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:02:06.631: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'CIR906.WLC.5508'running version 7.0.235.3 is rejected.
*Mar 1 00:02:06.631: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:02:06.631: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:02:06.631: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:02:06.631: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.114.44.131
*Mar 1 00:02:16.631: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'CIR906.WLC.5508'running version 7.0.235.3 is rejected.
*Mar 1 00:02:16.631: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:02:16.631: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:02:16.631: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:02:16.631: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.114.44.131
*Mar 1 00:02:26.631: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'CIR906.WLC.5508'running version 7.0.235.3 is rejected.
*Mar 1 00:02:26.631: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:02:26.631: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:02:26.631: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:02:26.631: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.114.44.131
Please Advise,
Thanks in Advanced,
Ahmed,Your WLC is running a 7.0.235.3. This firmware is suitable for your 1300 but you need at least 7.2.X to run 3600.
As I've mentioned in your other thread, you can get a refurbished 4402/4404 cheap from Cisco Refurbished. You can use the 4400 to run your 1310 and the 5508 to run the newer APs. -
Hi all
I'm having an issue with a 1252 LAP that is connected to the WLC over a WAN link.
Basically, it won't associate. The following is taken from a console into the LAP:
*Mar 1 00:00:07.799: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:08.799: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:26.851: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:27.003: Logging LWAPP message to 255.255.255.255.
%CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
%CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
%DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 10.148.x.x, mask 255.255.255.0, hostname AP002
2.90a3.533a
Translating "CISCO-LWAPP-CONTROLLER.nation.radix"...domain server (10.x.x.x)
%LWAPP-3-CLIENTEVENTLOG: Controller address 10.x.x.x obtained through DHCP
%LWAPP-3-CLIENTEVENTLOG: Did not get log server settings from DHCP.
%SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
%LWAPP-3-CLIENTEVENTLOG: Performing DNS resolution for CISCO-LWAPP-CONTROLLER.nation.radix
%LWAPP-3-CLIENTERRORLOG: DNS Name Lookup: could not resolve CISCO-LWAPP-CONTROLLER.nation.radix
%LWAPP-5-CHANGED: LWAPP changed state to JOIN
%LWAPP-3-CLIENTERRORLOG: Join Timer: did not recieve join response (controller - Fxxxxxxx)
%LWAPP-3-CLIENTERRORLOG: Set Transport Address: no more AP manager IP addresses remain
%SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: DID NOT GET JOIN RESPONSE.
%LWAPP-5-CHANGED: LWAPP changed state to DOWN
IOS Bootloader - Starting system.
Xmodem file system is available.
The ap-manager interface is configured correctly and there isn't a duplicate IP address.
The LAP was initially stand alone and was converted to LWAPP.
The MTU over the WAN link is 1500 bytes.
All I'm getting from the WLC debugs is:
Mon Jul 20 11:42:59 2009: 00:22:xx:xx:xx:xx Received LWAPP DISCOVERY REQUEST from AP 00:22:xx:xx:xx:xx to 00:19:xx:xx:xx:xx on port '29'
Mon Jul 20 11:42:59 2009: 00:22:xx:xx:xx:xx LWAPP Discovery Request AP Software Version: 0x3003300
Mon Jul 20 11:42:59 2009: 00:22:xx:xx:xx:xx Successful transmission of LWAPP Discovery Response to AP 00:22:xx:xx:xx:xx on port 29
So basically the join messages don't seem to reach the WLC. In fact they don't even seem to reach the local router on the remote subnet. The discovery packets are seen on the local router but the joins don't seem to appear at all.
I'm not sure if it's a latency issue. Average latency over the WAN link is under 70ms.
I'm assuming the certificate on the WAP is MIC and the MAC details have been entered into the WLC AP Security policies for authentication. I'm not seeing any debugging messages relating to bad authentication at all.
I can't debug from the LAP as it's LWAPP, obviously.
I've been through many Cisco documents trying to troubleshoot the problem, including this http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a00808f8599.shtml, but can't find a solution.
We're running WLC version 4.2.130.0.
Can anyone help?
Thanks
BrodieI assume you have connected to router's AUX and doing reverse telnet. You should be getting Password: prompt on your LAP's console. Password and Enable are both Cisco. Below is console output from my lab's 1250 LAP after erasing configuration (which can only be initiated from controller). In my case, the vlan is not configured with Option 43 and no proper DNS, so LAP doesn't join the controller.
By the way, your best bet might be to convert this LAP back to IOS and then back to LAP again. Use this method:
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
Do you have "Authorize APs against AAA" checked under Security > AP Policies in any of your WLCs ?
Press RETURN to get started!
*Mar 1 00:00:07.099: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:07.619: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:08.595: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*May 10 23:17:25.199: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*May 10 23:17:26.155: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1250 Software (C1250-K9W8-M), Version 12.4(10b)JDC, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Fri 01-May-09 10:49 by prod_rel_team
*May 10 23:17:26.155: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
*May 10 23:17:27.183: %SSH-5-ENABLED: SSH 2.0 has been enabled
*May 10 23:17:27.387: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*May 10 23:17:27.387: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*May 10 23:17:28.439: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*May 10 23:17:28.439: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*May 10 23:17:30.783: %LWAPP-3-CLIENTERRORLOG: ../lwapp/lwapp_l2.c:152 - discarding msg type 12 in state 0
*May 10 23:17:30.783: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*May 10 23:17:30.795: %DOT11-6-FREQ_SCAN: Interface Dot11Radio0, Scanning frequencies for 16 seconds
*May 10 23:17:44.571: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*May 10 23:17:44.731: Logging LWAPP message to 255.255.255.255.
%LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
%LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
%LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
%SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
%LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
%LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
%LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
%LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
%LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
%DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 172.16.8.3, mask 255.255.255.0, hostname AP0022.558e.24bc
User Access Verification
Password:
AP0022.558e.24bc>en
Password:
AP0022.558e.24bc#show lwapp ?
client LWAPP Client Information
ids LWAPP IDS Information
ip LWAPP IP configuration
mcast LWAPP Mcast Information
reap LWAPP REAP Information
rm LWAPP RM Information
AP0022.558e.24bc#show lwapp client config
AP0022.558e.24bc#
AP0022.558e.24bc#ping 3.45.47.143
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 3.45.47.143, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms
AP0022.558e.24bc# -
AP 360021 cannot join WLC 5508
Dears,
I have a cisco 5508 WLC and 40 cisco 360021 APs.
I configured the WLC and assign the management interface IP and also configured a DHCP pool on my Cisco 4507 core switch wit option 43.
But the problem that the APs connot join the WLC.
The below message appears:-
Nov 7 09:08:28.953: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Nov 7 09:08:28.954: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Nov 7 09:08:38.968: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Nov 7 09:08:39.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: x.x.x.x pe6
*Nov 7 09:08:39.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
Please support me to solve this issue.
Regards,Dears,
Also find the attched debug and the requirements that you asked for.
AP cisco debug:
*Oct 13 01:33:32.691: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Oct 13 01:33:34.691: %LINK-3-UPDOWN: Interface BVI1, changed state to up
*Oct 13 01:33:35.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Oct 13 01:33:35.691: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
*Oct 13 01:33:37.815: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Oct 13 01:33:37.903: status of voice_diag_test from WLC is false
*Oct 13 01:33:37.907: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Oct 13 01:33:37.907: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 13 01:33:38.815: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Oct 13 01:33:38.867: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Oct 13 01:33:38.875: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Oct 13 01:33:39.191: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Oct 13 01:33:39.223: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 10.10.107.58, mask 255.255.255.0, hostname APfc99.47a2.2ef7
*Oct 13 01:33:39.223: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Oct 13 01:33:39.899: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 13 01:33:40.899: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Oct 13 01:33:43.191: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Oct 13 01:33:43.259: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.10.107.58, mask 255.255.255.0, hostname APfc99.47a2.2ef7
*Oct 13 01:33:43.259: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Oct 13 01:33:47.907: %CAPWAP-3-ERRORLOG: Invalid event 29 & state 4 combination.
*Oct 13 01:33:47.907: %CAPWAP-3-ERRORLOG: SM handler: Failed to process timer message. Event 29, state 4
*Oct 13 01:33:47.907: %CAPWAP-3-ERRORLOG: Failed to handle timer message.
*Oct 13 01:33:47.907: %CAPWAP-3-ERRORLOG: Failed to process timer message.
*Oct 13 01:33:48.315: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Oct 13 01:33:48.379: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to ad
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (10.10.18.1) (10.10.18.100)
ministratively down
*Oct 13 01:33:48.467: status of voice_diag_test from WLC is false
*Oct 13 01:33:48.471: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 13 01:33:49.379: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Oct 13 01:33:49.431: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Oct 13 01:33:49.439: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Oct 13 01:33:49.471: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Oct 13 01:33:49.471: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Oct 13 01:33:50.463: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 13 01:33:51.463: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Oct 13 01:33:52.475: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Oct 13 01:33:52.483: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Oct 13 01:33:53.475: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Oct 13 01:33:53.507: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 13 01:33:54.507: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 23 23:47:46.583: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
*Mar 23 23:47:46.583: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
*Mar 23 23:47:46.583: %MESH-6-LINK_UPDOWN: Mesh station fc99.47a2.2ef7 link Down
*Mar 23 23:47:47.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.10.107.5:5246
*Mar 23 23:47:48.055: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar 23 23:47:48.119: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 23 23:47:48.211: status of voice_diag_test from WLC is false
*Mar 23 23:47:48.211: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 23 23:47:49.119: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 23 23:47:49.171: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 23 23:47:49.179: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 23 23:47:50.207: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 23 23:47:51.207: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 23 23:47:51.215: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 23 23:47:51.223: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 23 23:47:52.215: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 23 23:47:52.247: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 23 23:47:53.247: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.10.107.5
*Mar 24 00:25:36.579: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
*Mar 24 00:25:36.579: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
*Mar 24 00:25:36.579: %MESH-6-LINK_UPDOWN: Mesh station fc99.47a2.2ef7 link Down
APfc99.47a2.2ef7#
%CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Mar 24 00:33:27.519: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 24 00:33:28.003: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 00:33:28.035: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 00:33:28.043: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 00:33:28.051: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 00:33:29.079: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 00:33:30.079: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 24 00:33:32.519: %CAPWAP-5-SENDJOIN: sending Join Request to 10.10.107.5
*Mar 24 00:33:32.523: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 00:33:32.531: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 00:33:33.523: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 00:33:33.555: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 00:33:34.555: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radi
The Time on AP is not same time on the WLC
Oct 13 01:34:13.411: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Mar 24 02:02:36.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.10.107.5 peer_port: 5246
*Mar 24 02:02:36.003: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
User Access Verification
Username:
*Mar 24 02:02:36.011: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:02:37.003: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:02:37.035: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:02:38.035: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
Username:
*Mar 24 02:03:05.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2051 Max retransmission count reached!
Username: Cisco
Password:
APfc99.47a2.2ef7>
*Oct 13 01:34:13.411: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Mar 24 02:02:36.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.10.107.5 peer_port: 5246
*Mar 24 02:02:36.003: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
User Access Verification
Username:
*Mar 24 02:02:36.011: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:02:37.003: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:02:37.035: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:02:38.035: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
Username:
*Mar 24 02:03:05.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2051 Max retransmission count reached!
Username: Cisco
Password:
APfc99.47a2.2ef7>
*Mar 24 02:04:31.603: %IP-4-DUPADDR: Duplicate address 10.10.107.5 on BVI1, sourced by 0006.f661.d880?
memory set memory parameters
APfc99.47a2.2ef7#set
*Mar 24 02:04:33.103: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-start
*Mar 24 02:04:33.207: %CAPWAP-3-ERRORLOG: Invalid event 29 & state 4 combination.
*Mar 24 02:04:33.207: %CAPWAP-3-ERRORLOG: SM handler: Failed to process timer message. Event 29, state 4
*Mar 24 02:04:33.207: %CAPWAP-3-ERRORLOG: Failed to handle timer message.
*Mar 24 02:04:33.207: %CAPWAP-3-ERRORLOG: Failed to process timer messag
APfc99.47a2.2ef7#
*Mar 24 02:04:38.159: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar 24 02:04:38.223: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 24 02:04:38.315: status of voice_diag_test from WLC is false
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 24 02:04:38.315: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:04:39.223: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:04:39.275: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:04:39.283: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
%DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.10.107.5:5246
*Mar 24 02:06:58.999: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Mar 24 02:05:59.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.10.107.5 peer_port: 5246
*Mar 24 02:05:59.003: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:05:59.011: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:06:00.003: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:06:00.039: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:06:01.039: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
APfc99.47a2.2ef7#
APfc99.47a2.2ef7#
*Mar 24 02:09:50.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2051 Max retransmission count reached!
APfc99.47a2.2ef7#
APfc99.47a2.2ef7#
APfc99.47a2.2ef7#
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 24 02:10:20.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.10.107.5:5246
*Mar 24 02:10:21.055: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar 24 02:10:21.123: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 24 02:10:21.207: status of voice_diag_test from WLC is false
*Mar 24 02:10:21.211: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:10:22.123: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:10:22.175: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:10:22.183: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:10:23.211: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:10:24.211: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 24 02:10:25.787: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
*Mar 24 02:10:25.787: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
*Mar 24 02:10:25.787: %MESH-6-LINK_UPDOWN: Mesh station fc99.47a2.2ef7 link Down
*Mar 24 02:10:30.211: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 24 02:10:30.215: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:10:30.223: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:10:31.215: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:10:31.251: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:10:32.251: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 24 02:10:49.211: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 24 02:10:49.215: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:10:49.223: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:10:50.215: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:10:50.251: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:10:51.251: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 24 02:11:08.211: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 24 02:11:08.215: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:11:08.223: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:11:09.215: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:11:09.247: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:11:10.247: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 24 02:11:16.607: %IP-4-DUPADDR: Duplicate address 10.10.107.5 on BVI1, sourced by 0006.f661.d880
*Mar 24 02:11:18.107: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 24 02:11:18.211: %CAPWAP-3-ERRORLOG: Invalid event 29 & state 4 combination.
*Mar 24 02:11:18.211: %CAPWAP-3-ERRORLOG: SM handler: Failed to process timer message. Event 29, state 4
*Mar 24 02:11:18.211: %CAPWAP-3-ERRORLOG: Failed to handle timer message.
*Mar 24 02:11:18.211: %CAPWAP-3-ERRORLOG: Failed to process timer message.
*Mar 24 02:11:23.163: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar 24 02:11:23.227: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 24 02:11:23.319: status of voice_diag_test from WLC is false
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 24 02:11:23.319: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:11:24.227: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:11:24.275: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:11:24.283: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:11:25.311: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:11:26.311: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 24 02:11:33.319: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 24 02:11:33.323: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:11:33.331: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:11:34.323: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:11:34.355: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:11:35.355: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 24 02:11:43.319: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Mar 24 02:12:43.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.10.107.5 peer_port: 5246
*Mar 24 02:12:43.003: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:12:43.011: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:12:44.003: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:12:44.035: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:12:45.035: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 24 02:17:05.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.10.107.5:5246
*Mar 24 02:17:06.055: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar 24 02:17:06.119: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 24 02:17:06.203: status of voice_diag_test from WLC is false
*Mar 24 02:17:06.207: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:17:07.119: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:17:07.171: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:17:07.179: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:17:08.203: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:17:09.203: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 24 02:17:10.787: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
*Mar 24 02:17:10.787: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
*Mar 24 02:17:10.787: %MESH-6-LINK_UPDOWN: Mesh station fc99.47a2.2ef7 link Down
*Mar 24 02:17:15.207: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 24 02:17:15.211: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:17:15.219: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:17:16.211: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:17:16.247: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:17:17.247: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 24 02:17:53.207: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 24 02:17:53.211: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:17:53.219: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:17:54.211: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:17:54.247: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:17:55.247: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 24 02:18:01.607: %IP-4-DUPADDR: Duplicate address 10.10.107.5 on BVI1, sourced by 0006.f661.d880
*Mar 24 02:18:03.107: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 24 02:18:03.207: %CAPWAP-3-ERRORLOG: Invalid event 29 & state 4 combination.
*Mar 24 02:18:03.207: %CAPWAP-3-ERRORLOG: SM handler: Failed to process timer message. Even
Show requirement for AP:-
APfc99.47a2.2ef7#show version
Cisco IOS Software, C3600 Software (AP3G2-K9W8-M), Version 12.4(25e)JA, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Fri 27-Jan-12 21:27 by prod_rel_team
ROM: Bootstrap program is C3600 boot loader
BOOTLDR: C3600 Boot Loader (AP3G2-BOOT-M) LoaderVersion 12.4(23c)JY, RELEASE SOFTWARE (fc1)
APfc99.47a2.2ef7 uptime is 7 minutes
System returned to ROM by power-on
System image file is "flash:/ap3g2-k9w8-mx.124-25e.JA/ap3g2-k9w8-mx.124-25e.JA"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP3602I-A-K9 (PowerPC) processor (revision A0) with 167926K/81920K bytes of memory.
Processor board ID FGL1644Z15P
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.2.1.72
1 Gigabit Ethernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: FC:99:47:A2:2E:F7
Part Number : 73-14521-02
PCA Assembly Number : 800-37501-02
PCA Revision Number : A0
PCB Serial Number : FOC16414A83
Top Assembly Part Number : 800-35852-02
Top Assembly Serial Number : FGL1644Z15P
Top Revision Number : C0
Product/Model Number : AIR-CAP3602I-A-K9
Configuration register is 0xF
show inventry
NAME: "AP3600", DESCR: "Cisco Aironet 3600 Series (IEEE 802.11n) Access Point"
PID: AIR-CAP3602I-A-K9 , VID: V01, SN: FGL1644Z15P
show requirement on WLC
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.100.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
Build Type....................................... DATA + WPS
System Name...................................... Cisco_61:d8:84
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... 10.10.107.5
Last Reset....................................... Software reset
System Up Time................................... 0 days 1 hrs 4 mins 25 secs
System Timezone Location......................... (GMT +3:00) Baghdad
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... IQ - Iraq
Operating Environment............................ Commercial (0 to 40 C)
--More-- or (q)uit
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +40 C
External Temperature............................. +24 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Memory Current Usage............................. Unknown
Memory Average Usage............................. Unknown
CPU Current Usage................................ Unknown
CPU Average Usage................................ Unknown
Burned-in MAC Address............................ 00:06:F6:61:D8:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 100
WLC after debug enable
*spamApTask6: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Discovery resp:AC Name message element length = 58
*spamApTask6: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Discovery resp: WTP Radio Information msg length = 67
*spamApTask6: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Discovery resp: CAPWAP Control IPV4 Address len = 77
*spamApTask6: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Discovery resp: CAPWAP Control IPV6 Address len = 99
*spamApTask6: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Discovery resp: Mwar type payload len = 110
*spamApTask6: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Discovery resp: Time sync payload len = 125
*spamApTask6: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Discovery Response sent to 10.10.107.60:8944
*spamApTask6: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Discovery Response sent to 10.10.107.60:8944
*spamApTask6: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 WTP already released
*spamApTask2: Mar 24 04:56:19.133: fc:99:47:a2:2e:f7 CAPWAP Control Msg Received from 10.10.107.5:8944
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 packet received of length 123 from 10.10.107.5:8944
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Msg Type = 1 Capwap state = 0
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Discovery Request from 10.10.107.5:8944
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 msgEleLength = 1 msgEleType = 20
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Total msgEleLen = 94
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 msgEleLength = 40 msgEleType = 39
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Total msgEleLen = 50
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 msgEleLength = 1 msgEleType = 41
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Total msgEleLen = 45
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 msgEleLength = 1 msgEleType = 44
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Total msgEleLen = 40
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 msgEleLength = 10 msgEleType = 37
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Vendor specific payload from AP 54:78:1A:43:CA:D0 validated
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Total msgEleLen = 26
(Cisco Controller) >*sshpmLscTask: Mar 24 05:02:01.461: sshpmLscTask: LSC Task received a message 4
*Oct 13 01:33:48.191: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
User Access Verification
Username:
Username:
Username:
*Oct 13 01:33:50.191: %LINK-3-UPDOWN: Interface BVI1, changed state to up
*Oct 13 01:33:50.191: %IP-4-DUPADDR: Duplicate address 10.10.107.5 on BVI1, sourced by 0006.f661.d880
*Oct 13 01:33:51.191: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Oct 13 01:33:52.019: %CAPWAP-3-ERRORLOG: Invalid event 29 & state 4 combination.
*Oct 13 01:33:52.019: %CAPWAP-3-ERRORLOG: SM handler: Failed to process timer message. Event 29, state 4
*Oct 13 01:33:52.019: %CAPWAP-3-ERRORLOG: Failed to handle timer message.
*Oct 13 01:33:52.019: %CAPWAP-3-ERRORLOG: Failed to process timer message.
*Oct 13 01:33:53.251: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Oct 13 01:33:53.315: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to ad
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)ministratively down
*Oct 13 01:33:53.407: status of voice_diag_test from WLC is false
*Oct 13 01:33:53.411: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 13 01:33:54.315: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Oct 13 01:33:54.367: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Oct 13 01:33:54.375: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Oct 13 01:33:55.399: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 13 01:33:56.399: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 msgEleLength = 22 msgEleType = 37
nable
(Cisco Controller) >*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Vendor specific payload from AP 54:78:1A:43:CA:D0 validated
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 Total msgEleLen = 0
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 Join Priority Processing status = 0, Incoming Ap's Priority 4, MaxLrads = 100, joined Aps =0
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 1. 0 0
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 2. 232 3
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 3. 0 0
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 4. 100 0
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 Discovery resp: AC Descriptor message element len = 40
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 acName = Cisco_61:d8:84
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 Discovery resp:AC Name message element length = 58
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 Discovery resp: WTP Radio Information msg length = 67
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 Discovery resp: CAPWAP Control IPV4 Address len = 77
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 Discovery resp: CAPWAP Control IPV6 Address len = 99
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 Discovery resp: Mwar type payload len = 110
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 Discovery resp: Time sync payload len = 125
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 Discovery Response sent to 10.10.107.5:8944
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 Discovery Response sent to 10.10.107.5:8944
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 WTP already released
*spamApTask6: Mar 24 04:56:28.440: fc:99:47:a2:2e:f7 CAPWAP Control Msg Received from 10.10.107.60:8945
*spamApTask6: Mar 24 04:56:28.440: 54:78:1a:43:ca:d0 packet received of length 123 from 10.10.107.60:8945
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Msg Type = 1 Capwap state = 0
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Discovery Request from 10.10.107.60:8945
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 1 msgEleType = 20
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 94
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 40 msgEleType = 39
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 50
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 1 msgEleType = 41
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 45
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 1 msgEleType = 44
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 40
*spamApTask7: Mar 24 04:56:28.441: fc:99:47:a2:2e:f7 CAPWAP Control Msg Received from 10.10.107.61:8945
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 10 msgEleType = 37
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 packet received of length 123 from 10.10.107.61:8945
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Vendor specific payload from AP 54:78:1A:43:CA:D0 validated
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Msg Type = 1 Capwap state = 0
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 26
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 22 msgEleType = 37
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Discovery Request from 10.10.107.61:8945
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 1 msgEleType = 20
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Vendor specific payload from AP 54:78:1A:43:CA:D0 validated
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 94
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 40 msgEleType = 39
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 0
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 50
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 1 msgEleType = 41
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Join Priority Processing status = 0, Incoming Ap's Priority 4, MaxLrads = 100, joined Aps =0
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 45
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 1 msgEleType = 44
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 1. 0 0
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 40
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 2. 232 3
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 10 msgEleType = 37
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 3. 0 0
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Vendor specific payload from AP 54:78:1A:43:CA:D0 validated
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 4. 100 0
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 26
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 22 msgEleType = 37
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Discovery resp: AC Descriptor message element len = 40
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Vendor specific payload from AP 54:78:1A:43:CA:D0 validated
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 acName = Cisco_61:d8:84
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 0
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Discovery resp:AC Name message element length = 58
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Discovery resp: WTP Radio Information msg length = 67
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Join Priority Processing status = 0, Incoming Ap's Priority 4, MaxLrads = 100, joined Aps =0
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 1. 0 0
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 2. 232 3
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Discovery resp: CAPWAP Control IPV4 Address len = 77
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 3. 0 0 -
Hi all,
we have two new APs 1532E and we trying to join them into the WLC.
APs received correctly Management IP address but they doesn't appear in the WLC, we got the follow error message :
*Jul 16 09:29:46.499: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Jul 16 09:29:46.499: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Jul 16 09:29:46.499: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 172.31.93.250
*Jul 16 09:29:51.499: %CAPWAP-5-SENDJOIN: sending Join Request to 172.31.93.250
*Jul 16 09:30:45.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.31.93.250:5246
*Jul 16 09:30:46.031: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Jul 16 09:30:46.079: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Jul 16 09:30:46.307: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Jul 16 09:30:56.307: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jul 16 09:30:54.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.31.93.250 peer_port: 5246
*Jul 16 09:30:54.507: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.31.93.250 peer_port: 5246
*Jul 16 09:30:54.507: %CAPWAP-5-SENDJOIN: sending Join Request to 172.31.93.250
*Jul 16 09:30:54.511: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Jul 16 09:30:54.511: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Jul 16 09:30:54.511: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Jul 16 09:30:54.511: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 172.31.93.250
*Jul 16 09:30:59.507: %CAPWAP-5-SENDJOIN: sending Join Request to 172.31.93.250
*Jul 16 09:31:53.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.31.93.250:5246
*Jul 16 09:31:54.031: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Jul 16 09:31:54.079: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Jul 16 09:31:54.307: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Jul 16 09:32:03.383: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
*Jul 16 09:32:03.383: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
*Jul 16 09:32:03.383: Mesh setting the ethernet port 0 state to 0
*Jul 16 09:32:03.383: %MESH-6-LINK_UPDOWN: Mesh station 78da.6e60.8000 link Down
*Jul 16 09:32:04.307: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jul 16 09:31:59.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.31.93.251 peer_port: 5246
*Jul 16 09:32:06.075: Mesh setting the ethernet port 0 state to 2
Do I need to change Country into the WLC? We have configured IT and US.
We tried to put into the MAC filter the Dot11radio MAC address but nothing changed.
Thanks
MarcoHi,
I had the same join problem with a new CAP1552E outdoor model which should associate with 5508 WLC or WISM. According to all information I checked before we ordered the hardware, the ios version should support this. But could not get it working.
I found this information about the country-code and the MAC address filtering.
Removed the US-country-code next to BE-code and added the MAC-address of the AP and the problem was FIXED !!!
AP joined the controller. Thanks soo much for posting this very helpfull technical information.
Belgian Network technician. -
Unable to upgrade WLC 5508 using 7.4 IOS
while trying to push the new Software to a WLC i am getting error as mentioned.
(Cisco Controller) >transfer download path .
(Cisco Controller) >transfer download filename AIR-CT5500-K9-7-4-110-0.aes
(Cisco Controller) >transfer download start
Mode............................................. TFTP
Data Type........................................ Code
TFTP Server IP................................... x.x.x.x
TFTP Packet Timeout.............................. 6
TFTP Max Retries................................. 10
TFTP Path........................................ ./
TFTP Filename.................................... AIR-CT5500-K9-7-4-110-0.aes
This may take some time.
Are you sure you want to start? (y/N) y
TFTP Code transfer starting.
TFTP receive complete... extracting components.
Sanity check failed on file. The file was not downloaded completely! --- > What does this mean
TFTP Failure while storing in flash! (0)
the Size of file matches with Cisco and i am not sure how to check the MD5 on this file.
ftp> put c:/Intel/AIR-CT5500-K9-7-4-110-0.aes
ftp: 119537036 bytes sent in 921.35Seconds 129.74Kbytes/sec.
MD5: 4f30835b2170487c77ac23362dc8587d
Can anyone suggest why we are getting this.That error is usually because the file was corrupt when I have seen it in the past. Download an MD5 checker and verify the MD5 that is listed in the download when you hover your mouse over the file name.
http://m.download.cnet.com/MD5-Checker/3000-2092_4-10410639.html
Like Leo mentioned, make sure your tftp supports large files. I use 3cdeamon
Sent from Cisco Technical Support iPhone App -
Converted 1140 AP can't join the WLC 5508
Hello! Please, help me to sort my problem out.
We have bought autonomous APs AIR-AP1141N-E-K9 and converted them to the lightweight mode, but they cannot join the WLC 5508. The errors are below. There were NO problems with the LAPs that were bought before, together with the WLC.
AP's IP: 172.22.90.27 IOS version 12.4
WLC's IP: 172.22.90.20 IOS version 6.0.188.0
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
This Discussion has been converted into document:- https://supportforums.cisco.com/docs/DOC-23054
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
logs from the AP:
Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Oct 13 21:37:06.044: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 13 21:37:06.045: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 13 21:37:06.046: bsnInitRcbSlot: slot 1 has NO radio
*Oct 13 21:37:06.056: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to a
dministratively down
*Oct 13 21:37:06.066: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to r
eset
*Oct 13 21:37:06.098: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Oct 13 21:37:15.060: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLL
ER
*Oct 13 21:37:24.060: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
LER
*Oct 13 21:37:34.060: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Oct 13 21:38:34.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 172.22.90.20 peer_port: 5246
*Oct 13 21:38:34.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Oct 13 21:38:34.822: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 172.22.90.20 peer_port: 5246
*Oct 13 21:38:34.823: %CAPWAP-5-SENDJOIN: sending Join Request to 172.22.90.20
*Oct 13 21:38:34.823: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Oct 13 21:38:34.825: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Contr
ol Message from 172.22.90.20
*Oct 13 21:38:34.825: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 4.
*Oct 13 21:38:34.825: %CAPWAP-3-ERRORLOG: Failed to handle capwap control messag
e from controller
*Oct 13 21:38:39.823: %CAPWAP-5-SENDJOIN: sending Join Request to 172.22.90.20
*Oct 13 21:38:39.823: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Contr
ol Message from 172.22.90.20
*Oct 13 21:38:39.823: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 4.
*Oct 13 21:38:39.823: %CAPWAP-3-ERRORLOG: Failed to handle capwap control messag
e from controller
*Oct 13 21:38:39.824: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap p
acket from 172.22.90.20
*Oct 13 21:39:33.999: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 1
72.22.90.20:5246
*Oct 13 21:39:34.000: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Oct 13 21:38:34.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 172.22.90.20 peer_port: 5246
*Oct 13 21:38:34.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Oct 13 21:38:34.001: %DTLS-5-PEER_DISCONNECT: Peer 172.22.90.20 has closed conn
ection.
*Oct 13 21:38:34.001: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 1
72.22.90.20:5246
*Oct 13 21:38:34.001: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 3 combination
*Oct 13 21:38:34.125: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is
not established.
logs from the WLC:
debug capwap events enable
*Dec 21 15:02:06.244: 68:bc:0c:63:3d:a0 DTLS keys for Control Plane deleted successfully for AP 172.22.90.27
*Dec 21 15:02:06.246: 68:bc:0c:63:3d:a0 DTLS connection closed event receivedserver (172:22:90:20/5246) client (172:22:90:27/21077)
*Dec 21 15:02:06.246: 68:bc:0c:63:3d:a0 Entry exists for AP (172:22:90:27/21077)
*Dec 21 15:02:06.246: 68:bc:0c:63:3d:a0 apfSpamProcessStateChangeInSpamContext: Deregister LWAPP event for AP 68:bc:0c:63:3d:a0 slot 0
*Dec 21 15:02:06.246: 68:bc:0c:63:3d:a0 Deregister LWAPP event for AP 68:bc:0c:63:3d:a0 slot 0
*Dec 21 15:02:06.246: 68:bc:0c:63:3d:a0 apfSpamProcessStateChangeInSpamContext: Deregister LWAPP event for AP 68:bc:0c:63:3d:a0 slot 1
*Dec 21 15:02:06.246: 68:bc:0c:63:3d:a0 Deregister LWAPP event for AP 68:bc:0c:63:3d:a0 slot 1
Ble
*Dec 21 15:04:03.194: 68:bc:0c:63:3d:a0 capwap_ac_platform.c:1223 - Operation State 0 ===> 4
*Dec 21 15:04:03.194: 68:bc:0c:63:3d:a0 Register LWAPP event for AP 68:bc:0c:63:3d:a0 slot 0
*Dec 21 15:05:36.253: 68:bc:0c:63:3d:a0 Join Version: = 100711424
*Dec 21 15:05:36.253: 68:bc:0c:63:3d:a0 Join resp: CAPWAP Maximum Msg element len = 93
debug capwap errors enable
*Dec 21 16:16:51.879: 68:bc:0c:63:3d:a0 DTLS connection was closed
*Dec 21 16:17:09.940: 68:bc:0c:63:3d:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 12, joined Aps =5
debug capwap detail enable
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 CAPWAP Control Msg Received from 172.22.90.27:21078
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 packet received of length 281 from 172.22.90.27:21078
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 Msg Type = 3 Capwap state = 5
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 Join resp: Result Code message element len = 8
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 1. 47 0
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 2. 232 3
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 3. 6 0
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 4. 12 0
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 Join resp: AC Descriptor message element len = 48
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 acName = Wi-Fi_Controller
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 Join resp: AC Name message element len = 68
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 Join resp: WTP Radio Information message element len = 77
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 Join resp: CAPWAP Control IPV4 Address len = 87
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 Sending encrypted packet to AP 172:22:90:27 (21078)
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 Releasing WTP
*Dec 21 16:24:12.212: 68:bc:0c:63:3d:a0 CAPWAP Control Msg Received from 172.22.90.27:21077
*Dec 21 16:24:12.212: 68:bc:0c:63:3d:a0 DTLS connection 0x167c8b20 closed by controller
*Dec 21 16:24:12.212: DTL Deleting AP 9 - 0.0.0.0
*Dec 21 16:24:12.214: CAPWAP DTLS connection closed msg
*Dec 21 16:24:12.216: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'mfpSendEventReport+168' for AP 68:bc:0c:63:3d:a0(0)
*Dec 21 16:24:12.216: Received SPAM_MFP_RADIO_DOWN message
*Dec 21 16:24:12.218: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'l2roamInit+560' for AP 68:bc:0c:63:3d:a0(0)
*Dec 21 16:24:12.220: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'apfSpamCallbackInSpamContext+1224' for AP 68:bc:0c:63:3d:a0(0)
*Dec 21 16:24:12.222: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'apfSpamSendBlackListTable+376' for AP 68:bc:0c:63:3d:a0(0)
*Dec 21 16:24:12.224: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'rrmIappSendChdPacket+2320' for AP 68:bc:0c:63:3d:a0(0)
*Dec 21 16:24:12.226: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'asTrackInitTask+19360' for AP 68:bc:0c:63:3d:a0(0)
*Dec 21 16:24:12.228: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'mfpSendEventReport+168' for AP 68:bc:0c:63:3d:a0(1)
*Dec 21 16:24:12.228: Received SPAM_MFP_RADIO_DOWN message
*Dec 21 16:24:12.230: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'l2roamInit+560' for AP 68:bc:0c:63:3d:a0(1)
*Dec 21 16:24:12.232: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'apfSpamCallbackInSpamContext+1224' for AP 68:bc:0c:63:3d:a0(1)
*Dec 21 16:24:12.234: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'apfSpamSendBlackListTable+376' for AP 68:bc:0c:63:3d:a0(1)
*Dec 21 16:24:12.236: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'rrmIappSendChdPacket+2320' for AP 68:bc:0c:63:3d:a0(1)
*Dec 21 16:24:12.238: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'asTrackInitTask+19360' for AP 68:bc:0c:63:3d:a0(1)
*Dec 21 16:24:12.238: 68:bc:0c:63:3d:a0 Deleting and removing AP 68:bc:0c:63:3d:a0 from fast path
P.S. The time is set to the WLC with the NTP
P.P.S. Don't lookup at the time the logs were made - they were made not during the same day/timeI have solved this as soon as published my problem!!!
the answer is published here:
https://supportforums.cisco.com/thread/2004491
especially in the post of Matthew Fowler
Hi,
Please take a look at CSCte01087.
I see that your WLC is 10.0.13.5 and your AP is 10.0.13.28/24 so they are on the same subnet. I also see your AP MAC address does not begin with 00. This is why I believe it is relevant.
Please try the workaround or open a TAC case if you need a fix.
-Matt
Symptom:
An access point running 6.0.188.0 code may be unable to join a WLC5508.
Messages similar to the following will be seen on the AP.
%CAPWAP-3-ERRORLOG: Invalid AC Message Type 4.
%CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Control Message
Conditions:
At least one of the following conditions pertains:
- The high order byte of the AP's MAC address is nonzero, and the AP is in
the same subnet as the WLC5508's management (or AP manager) interface
- The WLC's management (or AP manager) interface's default gateway's
MAC address' high order byte is nonzero.
Workaround:
If the MAC address of the WLC's default gateway does not begin with 00,
and if all of the APs' MAC addresses begin with 00, then: you can put
the APs into the same subnet as the WLC's management (or AP manager)
interface.
In the general case, for the situation where the WLC's default gateway's
MAC does not begin with 00, you can address this by changing it to begin
with 00. Some methods for doing this include:
-- use the "mac-address" command on the gateway, to set a MAC address
that begins with 00
-- then enable HSRP on the gateway (standby ip ww.xx.yy.zz) and use this
IP as the WLC's gateway.
For the case where the APs' MAC addresses do not begin with 00, then make
sure that they are *not* in the same subnet as the WLC's management
(AP manager) interface, but are behind a router.
Another workaround is to downgrade to 6.0.182.0. However, after
downgrading the WLC to 6.0.182.0, any APs that have 6.0.188.0 IOS
(i.e. 12.4(21a)JA2) still installed on them will be unable to join.
Therefore, after downgrading the WLC, the APs will need to have a
pre-12.4(21a)JA2 rcvk9w8 or k9w8 image installed on them.
different vlan!!!! yes! thank you Matthew Fowler sooooo much!!!! -
AIR-CAP1602i cannot join a WLC 5508 controller
Hello,
I'm managing a large number of access points on a Cisco wlc 5508 controller.
We've recently purchased a bunch of new AIR-CAP1602I-E-K9.
note that we already have AIR-CAP1602I-E-K9 and other models in production.
These A.P are not able to join the controller for some reason, I've tried a lot of different things but I am now at a loss.
I have checked the regulatory domain, upgraded the FUS, manually upgraded the software version of the LAP to match the version on the other A.P.
I even downgraded/upgraded the WLC code (version 7.4.x and 8.0)
I use the dhcp option 43 to to send the controller IP.
Here are the info that can help:
errors:
#on A.P
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
#on WLC
Lwapp join request rejected (WLC version 7.6.130.0)
Failed to add database entry (WLC version 8.0)
WLC sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.6.130.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.101.1
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS
System Name...................................... XXX
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... XXX
Last Reset....................................... Software reset
System Up Time................................... 6 days 4 hrs 16 mins 27 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... Multiple Countries:CA,FR
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +41 C
External Temperature............................. +22 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 7
Number of Active Clients......................... 1977
Burned-in MAC Address............................ A4:93:4C:B0:E4:C0
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, OK
Maximum number of APs supported.................. 250
AP sh version
AP58f3.9cb8.3701#sh version
Cisco IOS Software, C1600 Software (AP1G2-K9W8-M), Version 15.2(4)JB6, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 22-Aug-14 10:56 by prod_rel_team
ROM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
AP58f3.9cb8.3701 uptime is 31 minutes
System returned to ROM by power-on
System image file is "flash:/ap1g2-k9w8-mx.152-4.JB6/ap1g2-k9w8-mx.152-4.JB6"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1602I-E-K9 (PowerPC) processor (revision B0) with 229366K/32768K bytes of memory.
Processor board ID FGL1832X5QU
PowerPC CPU at 533MHz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.6.100.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 58:F3:9C:B8:37:01
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC183171L4
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1832X5QU
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-E-K9
AP sh inventory
NAME: "AP1600", DESCR: "Cisco Aironet 1600 Series (IEEE 802.11n) Access Point"
PID: AIR-CAP1602I-E-K9 , VID: V01, SN: FGL1832X5QU
Thanks for your help !Hi Olivier,
The error messages that you have on the debugs:
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
It is related to the bug: CSCuh46442
https://tools.cisco.com/bugsearch/bug/CSCuh46442/?referring_site=ss
This bug is resolved in version : 8.0.100.0
http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/crn80.html#pgfId-1163951
Can you please paste here "show ap auth-list" from the controller CLI?
I suggest to enable MIC if it is not enabled, and then check if the AP's will join or not.
Kind Regards
Mohammad Setan -
WLC 5508 with LAP-1142n - Several Errors
Hello all,
I had installed a WLC 5508 with 7 LAP 1142n and 2 converted AP 1131abg.
I am seeing some errors relating 2 issues.
1st- One particular AP 1142 is disassociating and reseting the radios.
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
Thu Oct 28 11:50:49 2010
AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface reset. Status:NA
Thu Oct 28 11:50:49 2010
AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface reset. Status:NA
Thu Oct 28 11:50:49 2010
AP's Interface:1(802.11a) Operation State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface reset. Status:NA
Thu Oct 28 11:50:49 2010
AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface reset. Status:NA
Thu Oct 28 11:50:46 2010
AP's Interface:1(802.11a) Operation State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio reset due to Init. Status:NA
Thu Oct 28 11:50:46 2010
AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio reset due to Init. Status:NA
Thu Oct 28 11:50:46 2010
AP 'AP3', MAC: e8:04:62:23:ac:e0 disassociated previously due to AP Reset. Uptime: 1 days, 10 h 24 m 23 s . Last reset reason: operator changed 11g mode.
Thu Oct 28 11:50:35 2010
AP Disassociated. Base Radio MAC:e8:04:62:23:ac:e0
Thu Oct 28 11:50:35 2010
AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=New Discovery Status:NA
Thu Oct 28 11:50:35 2010
AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=New Discovery Status:NA
I had some search, and the new discovery cause, might be that the AP didnt know what WLC do associate, in a multi-controller environment. This is not the case. I only have one WLC in the same management vlan.
2st-The Radius server is beeing related in the logs as been deactivated. I raise the server time-out on Radius configuration option, but it still continues to do it.
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
Thu Oct 28 10:24:41 2010
RADIUS server 10.67.128.36:1812 deactivated in global list
Thu Oct 28 10:24:41 2010
RADIUS server 10.67.128.36:1812 failed to respond to request (ID 172) for client e8:06:88:51:c0:2b / user 'unknown'
Is this meaning the WLC stop sending request to the Radius Server ? We dont have BackUp Radius.
As far as i know, its always the same mac-address client that is associated to that error, maybe a iphone.
I had so many clients in that SSID and they are all working good.
The Radius server is a NPS from windows Server 2008
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
, and the client says that the medium response time is 0,02 sec, so im wondering why the controller is not getting response from Radius for a particular client?! My client also says, that didnt found any log related to that mac-address client ... what is weird...
WLC with last software available 7.0.164
Hope some one help me here.
Best Regards,
Bruno PetrónioThanks Scott,
I understand what you are mentioning, and i really didnt do it yet.
I realize that the primary controller was not configured on the
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
Wireless –> All APs –> High Availability tab, and did it only to the AP that is taking this beahviour.
Is this mandatory for a 1 controller only ?
No mather what the manual say, after that the AP is rebooting 2 mins in 2 mins... with the same kind of messages.
The interface on the switch is getting a few input errors and the same numbers of crc... but are so few...
Next step ... i will change it to another one's place/pathing cable.
Regarding the Radius messages... any ideas ?
I'm already on 30 sec's of server timeout.
Best Regards,
Bruno Petrónio -
Hi,
I have upgraded my WLC 5508 from 7.0 to 7.4 and the AP 1310 no longer can associate to WLC.
Seems that the AP doesn't work with WLC ver 7.4
Except changing these APs to autonomous mode, any other alternatives?
Besides, if we change them to autonomous mode, can Prime Infrastructure manage/monitor these APs?
thanks.The 1310 last support is on v7.0.x of the WLC. See the matrix below.
http://www.cisco.com/en/US/docs/wireless/controller/5500/tech_notes/Wireless_Software_Compatibility_Matrix.html
Prime Infrastructure can monitor the Autonomous access point but will not do anything else than monitor. Config changes is done via the bridge/AP itself.
Sent from Cisco Technical Support iPhone App -
Hi,
I have AP :OUTDOOR,AIR-LAP1524SB-N-K9 , i want to deploy this AP at difrent location , between WLC 5508( SW:6.0.196.0) and AP there are 2 nos of layer 3 Switches
connected with OSPF.
should i use DHCP option 43 to join the AP into WLC ??
How it will work , wht configuration i need to do in Windows based DHCP server ?
Thanks
Kuldip.Hello
Yes use option 43 to point the ap toward wlc.
here are two links to help you
http://www.cisco.com/en/US/docs/wireless/access_point/1520/installation/guide/1520_axf.html#wp1007791
and
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00808714fe.shtml#p2
Cheers -
WLC 5508 running 7.4.110.0 unable to tftp upload config from controller
Hi,
Two WLC 5508 running identical code version. One is 50 license Primary, the second is HA. Identical config on both. HA WLC can upload its config to the TFTP or FTP server but Primary cannot. The operation fails for both CLI and GUI and for different protocols i.e. TFTP, FTP.
#### Primary Controller
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.110.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.95.16
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS
System Name...................................... PRODWC7309
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... 10.1.30.210
Last Reset....................................... Power on reset
System Up Time................................... 18 days 18 hrs 51 mins 35 secs
System Timezone Location......................... (GMT+10:00) Sydney, Melbourne, Canberra
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... AU - Australia
Operating Environment............................ Commercial (0 to 40 C)
--More-- or (q)uit
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +34 C
External Temperature............................. +17 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 8
Number of Active Clients......................... 138
Memory Current Usage............................. Unknown
Memory Average Usage............................. Unknown
CPU Current Usage................................ Unknown
CPU Average Usage................................ Unknown
Burned-in MAC Address............................ 3C:08:F6:CA:52:20
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, OK
Maximum number of APs supported.................. 50
(Cisco Controller) >debug transfer trace enable
(Cisco Controller) >transfer upload start
Mode............................................. TFTP
TFTP Server IP................................... 10.1.22.2
TFTP Path........................................ /
TFTP Filename.................................... PRODWC7309-tmp.cfg
Data Type........................................ Config File
Encryption....................................... Disabled
*** WARNING: Config File Encryption Disabled ***
Are you sure you want to start? (y/N) Y
*TransferTask: Jun 02 10:41:15.183: Memory overcommit policy changed from 0 to 1
*TransferTask: Jun 02 10:41:15.183: RESULT_STRING: TFTP Config transfer starting.
TFTP Config transfer starting.
*TransferTask: Jun 02 10:41:15.183: RESULT_CODE:1
*TransferTask: Jun 02 10:41:24.309: Locking tftp semaphore, pHost=10.1.22.2 pFilename=/PRODWC7309-tmp.cfg
*TransferTask: Jun 02 10:41:24.393: Semaphore locked, now unlocking, pHost=10.1.22.2 pFilename=/PRODWC7309-tmp.cfg
*TransferTask: Jun 02 10:41:24.393: Semaphore successfully unlocked, pHost=10.1.22.2 pFilename=/PRODWC7309-tmp.cfg
*TransferTask: Jun 02 10:41:24.394: tftp rc=-1, pHost=10.1.22.2 pFilename=/PRODWC7309-tmp.cfg
pLocalFilename=/mnt/application/xml/clis/clifile
*TransferTask: Jun 02 10:41:24.394: RESULT_STRING: % Error: Config file transfer failed - Unknown error - refer to log
*TransferTask: Jun 02 10:41:24.394: RESULT_CODE:12
*TransferTask: Jun 02 10:41:24.394: Memory overcommit policy restored from 1 to 0
% Error: Config file transfer failed - Unknown error - refer to log
(Cisco Controller) >show logging
*TransferTask: Jun 02 10:41:24.393: #UPDATE-3-FILE_OPEN_FAIL: updcode.c:4579 Failed to open file /mnt/application/xml/clis/clifile.
*sshpmReceiveTask: Jun 02 10:41:24.315: #OSAPI-3-MUTEX_FREE_INFO: osapi_sem.c:1087 Sema 0x2b32def8 time=142 ulk=1621944 lk=1621802 Locker(sshpmReceiveTask sshpmrecv.c:1662 pc=0x10b07938) unLocker(sshpmReceiveTask sshpmReceiveTaskEntry:1647 pc=0x10b07938)
-Traceback: 0x10af9500 0x1072517c 0x10b07938 0x12020250 0x12080bfc
*TransferTask: Jun 02 10:39:01.789: #UPDATE-3-FILE_OPEN_FAIL: updcode.c:4579 Failed to open file /mnt/application/xml/clis/clifile.
*sshpmReceiveTask: Jun 02 10:39:01.713: #OSAPI-3-MUTEX_FREE_INFO: osapi_sem.c:1087 Sema 0x2b32def8 time=5598 ulk=1621801 lk=1616203 Locker(sshpmReceiveTask sshpmrecv.c:1662 pc=0x10b07938) unLocker(sshpmReceiveTask sshpmReceiveTaskEntry:1647 pc=0x10b07938)
-Traceback: 0x10af9500 0x1072517c 0x10b07938 0x12020250 0x12080bfc
#### HA Controller
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.110.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.95.16
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS
System Name...................................... PRODWC7310
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... 10.1.31.210
Last Reset....................................... Software reset
System Up Time................................... 18 days 19 hrs 1 mins 27 secs
System Timezone Location......................... (GMT+10:00) Sydney, Melbourne, Canberra
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... AU - Australia
Operating Environment............................ Commercial (0 to 40 C)
--More-- or (q)uit
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +34 C
External Temperature............................. +17 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 4
Number of Active Clients......................... 0
Memory Current Usage............................. Unknown
Memory Average Usage............................. Unknown
CPU Current Usage................................ Unknown
CPU Average Usage................................ Unknown
Burned-in MAC Address............................ 3C:08:F6:CA:53:C0
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, OK
Maximum number of APs supported.................. 500
(Cisco Controller) >debug transfer trace enable
(Cisco Controller) >transfer upload start
Mode............................................. FTP
FTP Server IP.................................... 10.1.22.2
FTP Server Port.................................. 21
FTP Path......................................... /
FTP Filename..................................... 10_1_31_210_140602_1050.cfg
FTP Username..................................... ftpuser
FTP Password..................................... *********
Data Type........................................ Config File
Encryption....................................... Disabled
*** WARNING: Config File Encryption Disabled ***
Are you sure you want to start? (y/N) y
*TransferTask: Jun 02 10:51:31.278: Memory overcommit policy changed from 0 to 1
*TransferTask: Jun 02 10:51:31.278: RESULT_STRING: FTP Config transfer starting.
FTP Config transfer starting.
*TransferTask: Jun 02 10:51:31.278: RESULT_CODE:1
*TransferTask: Jun 02 10:52:05.468: ftp operation returns 0
*TransferTask: Jun 02 10:52:05.477: RESULT_STRING: File transfer operation completed successfully.
*TransferTask: Jun 02 10:52:05.477: RESULT_CODE:11
File transfer operation completed successfully.
Not upgrading to 7.4.121.0 because of bug CSCuo63103. Have not restarted the controller yet.
Any one else had this issue ? Is there a workaround ?
Thanks,
Rick.Thanks Stephen, In my deployments of 7.4.110.0 version I have not seen this issue so may be controller reboot will fix it (we do have HA to minimize the impact). I will keep the thread updated with findings and may request TAC for the special release 7.4.121.0 if the still not happy with 7.4.110.0
Rick. -
Unable to upload/download the configuration in WLC 5508
Dear Friends,
I do have issue in upgrading firmware or downloading code from WLC 5508 , version 7.0. I did the same image upload with other devices through CLI from my notebook and it works fine.
Everytime i try to upload/download the image, it gives the error .
Has anyone faced the issues, is there any workaround ?
Regards,
SIDI believe that is just how Cisco designed it:). I believe in earlier versions this worked.
I don't like it now because I cant download the config on a wlc of the ap I'm on. The enable managent via wireless is totally different... As you know, you can manage it.... Sort of:)
Thanks,
Scott Fella
Sent from my iPhone -
Low Bandwith, WLC 5508 and LAP 1142N, please help !
Hello Everyone
For the Environment:
- I have a WLC 5508 With a license up to 100 AP, at the Point there are 39 AP connected.
- The WLC is connected with 8x 1Gbit/s, as a Trunk ==> 2 Members of 3750 Switches Stack ( 4gig and 4 gig)
- The AP are connected to diferent 2960s with an Uplink ( 3 Gbit/s) to the 3750 Switches
- There are max. 12 AP on each 2960s
- The AP are powered over Ethernet
The AP:
- it runs a/b/g/n and on 2,4 Ghz i schould have 300 mbit/s as for the 5 Ghz it schould also run 300mbit /s
- the Ap has an uplink of 1 Gbit/s
The clients:
- have a intel Wifi link 5300 AGN Card
To the Problem:
- if i connect to one AP, and the Signal strength is High, i get an upload rate of max. 6-8Mbyte/s.
and i am the only Person uploading.
if i upload from 3 clients the same data from the same spot to the same target i get 2-3 Mbyte/s per client.
if connect to the same target and run over ethernet cable fom the same spot, i get an upload of 70 -85 Mbyte/s.
Question:
- Why am i having these Bandwith problems ??Thanks Scott,
I understand what you are mentioning, and i really didnt do it yet.
I realize that the primary controller was not configured on the
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
Wireless –> All APs –> High Availability tab, and did it only to the AP that is taking this beahviour.
Is this mandatory for a 1 controller only ?
No mather what the manual say, after that the AP is rebooting 2 mins in 2 mins... with the same kind of messages.
The interface on the switch is getting a few input errors and the same numbers of crc... but are so few...
Next step ... i will change it to another one's place/pathing cable.
Regarding the Radius messages... any ideas ?
I'm already on 30 sec's of server timeout.
Best Regards,
Bruno Petrónio -
AIR-CAP1602I-E-K9 Not Talking to WLC 5508
hi all,
can't seem to get my APs to talk to WLC 5508.
can someone advise which WLC firmware to use and where can i get/download (link pls).
currently WLC is running 6.0.199.4.
Mar 1 00:00:47.839: %CDP_PD-4-POWER_OK: All radios disabled - NEGOTIATED inlin
e power source
*Mar 1 00:00:53.931: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:00:55.963: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP addre
ss 172.28.159.15, mask 255.255.255.192, hostname APfc99.47a3.4d22
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:01:06.899: %CAPWAP-3-ERRORLOG: Did not get log server settings from D
HCP.
*Mar 1 00:01:15.899: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
LER
*Mar 1 00:01:15.899: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_f8
:72:64'running version 6.0.199.4 is rejected. <<<<
APfc99.47a3.4d22>sh ve
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:52 by prod_rel_team
ROM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFT
WARE (fc1)
APfc99.47a3.4d22 uptime is 11 minutes
System returned to ROM by power-on
System image file is "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1602I-E-K9 (PowerPC) processor (revision B0) with 98294K/32768K
bytes of memory.
Processor board ID FGL1726W6DQ
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.4.1.37
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: FC:99:47:A3:4D:22
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC17182J4J
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1726W6DQ
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-E-K9
Configuration register is 0xFHi,
Date and time is ok on the WLC,
I configured Accept Self Signed Certificate (SSC) under Security / AP policy, once done the WLC recognized the AP, but output from the console of the AP power cycle the access point is:
IOS Bootloader - Starting system.
FLASH CHIP: Micronix MX25L256_35F
Xmodem file system is available.
flashfs[0]: 5 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31936000
flashfs[0]: Bytes used: 6551040
flashfs[0]: Bytes available: 25384960
flashfs[0]: flashfs fsck took 9 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: 4c:00:82:9a:47:a3
************* loopback_mode = 0
Loading "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx"...####################
File "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx" uncompressed and installed, entr
y point: 0x100000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:52 by prod_rel_team
Initializing flashfs...
FLASH CHIP: Micronix MX25L256_35F
flashfs[2]: 5 files, 2 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 31808000
flashfs[2]: Bytes used: 6551040
flashfs[2]: Bytes available: 25256960
flashfs[2]: flashfs fsck took 9 seconds.
flashfs[2]: Initialization complete.
flashfs[3]: 0 files, 1 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 11999232
flashfs[3]: Bytes used: 1024
flashfs[3]: Bytes available: 11998208
flashfs[3]: flashfs fsck took 1 seconds.
flashfs[3]: Initialization complete....done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
memory validate-checksum 30
^
% Invalid input detected at '^' marker.
no ip http server
^
% Invalid input detected at '^' marker.
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
login authentication default
^
% Invalid input detected at '^' marker.
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Warning: the compile-time code checksum does not appear to be present.
cisco AIR-CAP1602I-N-K9 (PowerPC) processor (revision B0) with 98294K/32768K
bytes of memory.
Processor board ID FGL1730S57A
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.4.1.37
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 4C:00:82:9A:47:A3
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC17284HL9
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1730S57A
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-N-K9
% Please define a domain-name first.
logging facility kern
^
% Invalid input detected at '^' marker.
logging trap emergencies
^
% Invalid input detected at '^' marker.
Press RETURN to get started!
*Mar 1 00:00:12.451: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Mar 1 00:00:13.683: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state
to up
*Mar 1 00:00:14.687: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 00:00:15.123: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:52 by prod_rel_team
*Mar 1 00:00:15.151: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Mar 1 00:00:15.151: %CAPWAP-3-ERRORLOG: Failed to load configuration from flas
h. Resetting to default config
*Mar 1 00:00:16.195: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, chan
ged state to uplwapp_crypto_init: MIC Present and Parsed Successfully
no bridge-group 1 source-learning
^
% Invalid input detected at '^' marker.
%Default route without gateway, if not a point-to-point interface, may impact pe
rformance
*Mar 1 00:00:48.695: %CDP_PD-4-POWER_OK: All radios disabled - INJECTOR_CONFIGU
RED_ON_SOURCE inline power source
*Mar 1 00:00:48.923: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP addre
ss 10.2.3.100, mask 255.255.255.0, hostname AP4c00.829a.47a3
Translating "CISCO-CAPWAP-CONTROLLER.campeche.ecosur.mx"...domain server (10.2.3
.10) [OK]
*Mar 1 00:00:59.915: %CAPWAP-3-ERRORLOG: Did not get log server settings from D
HCP.
*Mar 1 00:00:59.919: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is
not established. A0203E6, 147E, A020364, A47B, 0
*Mar 1 00:01:09.915: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan 29 09:33:18.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 10.2.3.230 peer_port: 5246
*Jan 29 09:33:18.535: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 10.2.3.230 peer_port: 5246
*Jan 29 09:33:18.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
*Jan 29 09:33:23.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
logging facility kern
^
% Invalid input detected at '^' marker.
logging trap emergencies
^
% Invalid input detected at '^' marker.
*Jan 29 09:34:17.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.
2.3.230:5246
*Jan 29 09:34:17.999: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led sta
te 255
*Jan 29 09:34:17.999: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 29 09:34:17.999: %CAPWAP-3-ERRORLOG: Failed to load configuration from flas
h. Resetting to default config
*Jan 29 09:34:28.015: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan 29 09:34:28.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 10.2.3.230 peer_port: 5246
*Jan 29 09:34:28.535: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 10.2.3.230 peer_port: 5246
*Jan 29 09:34:28.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
*Jan 29 09:34:33.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
and debug command output enable CAPWAP events
(Cisco Controller) >debug capwap events enable
(Cisco Controller) >*spamApTask7: Jan 29 03:39:08.092: acDtlsPlumbControlPlaneKeys: lrad:10.2.3.100(42107) mwar:10.2.3.230(5246)
*spamApTask7: Jan 29 03:39:08.093: 4c:00:82:9a:47:a0 DTLS keys for Control Plane deleted successfully for AP 10.2.3.100
*spamApTask7: Jan 29 03:39:08.100: 4c:00:82:9a:47:a0 DTLS connection closed event receivedserver (10.2.3.230/5246) client (10.2.3.100/42107)
*spamApTask7: Jan 29 03:39:08.100: 4c:00:82:9a:47:a0 Entry exists for AP (10.2.3.100/42107)
*spamApTask7: Jan 29 03:39:08.100: 4c:00:82:9a:47:a0 No AP entry exist in temporary database for 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.104: 4c:00:82:9a:47:a0 Discovery Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.104: 4c:00:82:9a:47:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 500, joined Aps =0
*spamApTask7: Jan 29 03:39:08.104: apModel:
*spamApTask7: Jan 29 03:39:08.104: apType = 38 apModel:
*spamApTask0: Jan 29 03:39:08.105: 4c:00:82:9a:47:a3 Received LWAPP DISCOVERY REQUEST to 6c:41:6a:5f:95:2f on port '13'
*spamApTask0: Jan 29 03:39:08.105: 4c:00:82:9a:47:a3 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100 port 42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 500, joined Aps =0
*spamApTask7: Jan 29 03:39:08.105: apModel:
*spamApTask7: Jan 29 03:39:08.105: apType = 38 apModel:
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100 port 42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 500, joined Aps =0
*spamApTask7: Jan 29 03:39:08.105: apModel:
*spamApTask7: Jan 29 03:39:08.105: apType = 38 apModel:
*spamApTask7: Jan 29 03:39:08.106: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100 port 42107
(Cisco Controller) >*spamApTask7: Jan 29 03:39:08.106: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:18.104: 4c:00:82:9a:47:a3 DTLS connection not found, creating new connection for 10:2:3:100 (42107) 10:2:3:230 (5246)
*spamApTask7: Jan 29 03:39:18.638: acDtlsPlumbControlPlaneKeys: lrad:10.2.3.100(42107) mwar:10.2.3.230(5246)
*spamApTask7: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 Allocated index from main list, Index: 397
*spamApTask7: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 Using CipherSuite AES128-SHA
*spamApTask7: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 DTLS keys for Control Plane are plumbed successfully for AP 10.2.3.100. Index 398
*spamApTask6: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 DTLS Session established server (10.2.3.230:5246), client (10.2.3.100:42107)
*spamApTask6: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 Starting wait join timer for AP: 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:23.636: 4c:00:82:9a:47:a0 Join Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:23.636: 4c:00:82:9a:47:a3 Deleting AP entry 10.2.3.100:42107 from temporary database.
*spamApTask7: Jan 29 03:39:23.637: 4c:00:82:9a:47:a0 MIC AP is not allowed to join by config
*spamApTask7: Jan 29 03:39:23.637: 4c:00:82:9a:47:a0 Join Request failed!
Maybe you are looking for
-
Hi , I am creating a order ( for which Delivery Not created ) for which schedule line delivery date is alloted . Which i can check in VBEP table . But when extracting the data in 2Lis_12_VCSCL , the order is not coming . Is the extractor is correc
-
I have an ipod touch first generation and it is telling me to connect to itunes but it isn't recognized by itunes when i try to connect it. what do i do?
-
Remote managment Exchange 2013 SP1 from C# code using Power-Shell.
Hello, Sorry if I am describing something wrong, but it is first time I am using Microsoft development forum. I am trying to built library that will manage Exchange remotely using C# code (VS 2012) and Power-Shell ver.4.0. My workstation and the act
-
Hi all, Could anyone please let me know the difference between the status of a Purchase Order under the Order collaboration tab and Reporting tab? I see that the PO has the status of 'Confirmed' under the Supplier Collaboration tab and 'closed' under
-
Whats the best way to place an image in DW CS5.5
Hello all, what is the best way to place an image exactly where I would like it to go in Dreamweaver CS5.5? I have my images sliced in Fireworks already. Also since my images are sliced already in Fireworks is there a way to place the images exaclty