1310 Root Bridge will not Authenticate with 350 Non Root Bridge

I've exhausted myself solving this issue.
I have a 1310 set as a root bridge using WEPS. I have a 350 set as a non root bridge/without clients, also using WEPS (they both use the same SSID)
The 350 will not authenticate to the 1310. After doing a Carrier Busy Test, it is clear the 350 see's the 1310 with signal strengh of 100 percent.
(I have a test lab setup in my office)
If I make the 350 the Root Bridge and the 1310 the Non Root, The 1310 will authenticate to the 350.
I hoping someone else has seen this problem and can enlighten me.
Thank you.

I have successfully configured a 1310 Bridge as a Root Bridge and a BR350 Bridge and a Non Root Bridge/with Clients. I also had to force the 1310 to operate at 11MB only.
As soon as I make the BR350 Bridge a Non Root Bridge/without Clients, the authentication is dropped between the two.
I was hoping I could transition to the 1310 one unit at a time since I have over a dozen 350's to replace.

Similar Messages

Illustrator CS2 bridge will not open with Illustrator CS6 installed

I had CS6 loaded and working well but when I uninstalled a previously loaded copy of Illustrator CS2 my Bridge would not fire up. I tried reloading Illustrator from CS6 disc but it still would not work.What can I do?

Try using the Adobe Creative Suite Cleaner Tool
helps resolve installation problems for CS3 thru CS6 and for Creative Cloud
http://www.adobe.com/support/contact/cscleanertool.html

Disney apps will not authenticate with FIOS

On my Apple TV and iOS devices I cannot get Disney apps, or any apps that require authentication, to authenticate with Verizon FIOS. I enter the correct information and then after login the spinning symbol just spins and spins. Anyone else seeing this?

I have tried this and get the spinning issue with all disney apps and ABC. For some reason PBS is working for me right now.
I have tried it with the following browsers:
Chrome
Safari
Firefox
IOS
I've even logged into a work computer remotely and tried internet explorer
This is driving me insane.

I am considering purchase of Airport Express to extend / improve my network at home. I have read that AE will not work with a non apple set up. Does this mean my BT Homehub will not work with AE?

I have poor router connection to my iphone in one part of my three storey home. I have a BT Homehub router. I am considering purchase of Airport Express to improve my network connection. Will AE function with the Homehub. I have read that it may not! Any advice please?
Geoff Snr

The AirPort Express will work with the Homehub if you establish a permanent Ethernet connection from one of the LAN <-> ports on the Homehub to the WAN "O" port on the AirPort Express.
The AirPort Express will not work if you are planning to connect the Express to the Homehub wirelessly to extend the network.

Adobe Bridge will not open (with CS6 Extended)

I Installed a student version of CS6 Extended a couple weeks ago and I have used Bridge with it a few times but all of a sudden it wont open. Photoshop opens perfect but bridge doesnt even come up with any error messages...just nothing. Can any one help me? Please? Thank you

Try resetting preferences. Hold down Crtl key (option on mac) and start Bridge. Should get a reset window.

W2K will not authenticate to Mac OS X Server.

My Mac OS X 10.4.3 will authenticate via Open Directory, but my Windows 2000 Pro. machine will not authenticate with Active Directory. Is there any trick to get Active Directory running on the OS X Server?
Thanks.

Your question would be easier to answer if you had included information of what Mac you have and what version of Garageband you are trying to reinstall.
And why you deleted it in the first place.

My new apps have changed to try within creative cloud; and my installed apps will not authenticate. I recently canceled one subscription and replaced it with another.

My new apps have changed to try within creative cloud; and my installed apps will not authenticate. I recently canceled one subscription and replaced it with another. Can you please look at it and correct?

Solution for Windows 8.1: Locate the C:\Users\USER\AppData\Local\Adobe\OOBE folder. Log out of Creative Cloud and from Task Manager end task for Creative Cloud. From the OOBE folder delete ALL files. Do not delete folders (com.adobe.accc.apps & com.adobe.accc.home). When complete, restart Creative Cloud and log in with ID and Password.

CS5 Bridge will not open, Air will not install, and AAM Updater will not update. Please help!

I am having several problems with CS5, and as best I can tell they all seem to be related. I purchased CS5 about a month ago. Photoshop has opened and ran fine. However, recently AAM notified me some several updates available. When I tried to update them they all failed. This lead to the discovery that Bridge will not open at all, Air installs but with an error and cannot update itself or applications like Adobe Help, and since the AAM updater ran it now thinks everything is up to date.
I have search endlessly for every piece of information I could find on this issue. As well as, sat on the phone with tech support for hours. As best I can tell, (and really I have no evidence to support me), it seems to all be related to a permissions issues. However, I have tried everything the forums suggested with no luck, and Tech Support ended with me doing an Uninstall and reinstall (twice), while repairing permissions in-between. I am about at the end of the road with this issue and would greatly appreciate any additional suggests you could offer.
Some additional details.
Running a MBP i7, 8GB RAM, and MAC OSX 10.6.4
Bridge Issue,
     When attempting to launch Bridge it simply returns an error "This operation could not be completed..." I tried the option click and reset method, no luck.
Air Issue,
     Kind of works, but at the same time doesn't. In that in one of the previous installations programs like Adobe Help would not run. Now Help does run, however, when I go to update Air it says it completed successfully but then immediately gives me an error saying "~this may not be allowed by the administrator..." I also cannot update Adobe Help, it just sits and says preparing to update.
AAM Updater Issue,
     This appeared to work fine until I attempted to install an update. It downloaded everything and then failed on the install. However, now it thinks everything is up to date, but nothing is.

Well despite not getting much love on this forum. I was able to correct the problem. I tried every solution that google would produce on these issues. Ultimately it came done to permission issue. I was lead to this fix by a person on flickr that suggested permissions as the cause. However, his solution was to modify the permissions in the home directory root and apply them to every subsequent folder in the home directory. Although quick and easy, I felt this would lead to more trouble then it was worth.
I did some more digging and what I discovered is that all the permission of the Adobe folders in the home directory library (not the HD library) and the application folder did not match all the other folders in those areas. Some of the files in some of the folders did not match either. So I made them match (the ones that matched I left alone), and everything seemingly went back to working normally. It was a bit of a pain going folder by folder. Fortunately there where not many of them. About 8 in total, plus the internal folders.

Cisco 1142 Wireless access point intermittently will not authenticate

Hi all,
We have a Cisco 1142 standalone access point, and from time to time I will come into the office and it will not authenticate any users to either our guest or corporate networks. I then have to go in and reboot the access point. After that, it begins to work. Any advice? Here's my configuration below:
Current configuration : 6450 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname cisco-chiap01
logging monitor errors
enable secret 5 $1$fsD8$CU42/3/Up5AAlL4hQWvvg0
aaa new-model
aaa group server radius rad_eap
server 172.17.16.12 auth-port 1645 acct-port 1646
server 172.17.21.10 auth-port 1812 acct-port 1813
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
server 172.17.21.10 auth-port 1812 acct-port 1813
aaa group server radius rad_eap2
server 172.17.16.12 auth-port 1645 acct-port 1646
server 172.17.21.10 auth-port 1812 acct-port 1813
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authentication login eap_methods2 group rad_eap2
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
login on-failure log
login on-success log
dot11 syslog
dot11 vlan-name Admin vlan 100
dot11 vlan-name DevNetwork vlan 20
dot11 vlan-name Guest vlan 150
dot11 vlan-name Network vlan 16
dot11 ssid DevNetwork
vlan 20
authentication open eap eap_methods2
authentication network-eap eap_methods2
authentication key-management wpa version 2
dot11 ssid Guest
vlan 150
authentication open
authentication key-management wpa version 2
guest-mode
mbssid guest-mode
wpa-psk ascii 7 142407060101380B013A3A2670435642
information-element ssidl advertisement
dot11 ssid Network
vlan 16
authentication open eap eap_methods2
authentication network-eap eap_methods2
authentication key-management wpa version 2
username monkeyman privilege 15 secret 5 $1$ZZ7C$rqimu2FNONdfeacMNGAD/.
bridge irb
interface Dot11Radio0
no ip address
ip helper-address 172.17.19.10
no ip route-cache
encryption mode ciphers aes-ccm
encryption vlan 16 mode ciphers aes-ccm
encryption vlan 150 mode ciphers aes-ccm
encryption vlan 20 mode ciphers aes-ccm
ssid DevNetwork
ssid Guest
ssid Network
antenna gain 0
parent timeout 120
speed 5.5 11.0 basic-6.0 9.0 12.0 36.0 48.0 54.0
packet retries 128 drop-packet
channel 2462
station-role root
rts threshold 512
rts retries 128
interface Dot11Radio0.11
encapsulation dot1Q 11
no ip route-cache
interface Dot11Radio0.16
encapsulation dot1Q 16 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
bridge-group 20 subscriber-loop-control
bridge-group 20 block-unknown-source
no bridge-group 20 source-learning
no bridge-group 20 unicast-flooding
bridge-group 20 spanning-disabled
interface Dot11Radio0.150
encapsulation dot1Q 150
no ip route-cache
bridge-group 150
bridge-group 150 subscriber-loop-control
bridge-group 150 block-unknown-source
no bridge-group 150 source-learning
no bridge-group 150 unicast-flooding
bridge-group 150 spanning-disabled
interface Dot11Radio1
no ip address
ip helper-address 172.17.19.10
no ip route-cache
encryption vlan 16 mode ciphers aes-ccm
encryption vlan 150 mode ciphers aes-ccm
encryption vlan 20 mode ciphers aes-ccm
ssid DevNetwork
ssid Guest
ssid Network
antenna gain 0
traffic-metrics aggregate-report
dfs band 3 block
mbssid
parent timeout 120
speed 6.0 12.0 basic-24.0 36.0 48.0 54.0
channel width 40-above
channel dfs
station-role root access-point
interface Dot11Radio1.11
encapsulation dot1Q 11
no ip route-cache
interface Dot11Radio1.16
encapsulation dot1Q 16 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
bridge-group 20 subscriber-loop-control
bridge-group 20 block-unknown-source
no bridge-group 20 source-learning
no bridge-group 20 unicast-flooding
bridge-group 20 spanning-disabled
interface Dot11Radio1.150
encapsulation dot1Q 150
no ip route-cache
bridge-group 150
bridge-group 150 subscriber-loop-control
bridge-group 150 block-unknown-source
no bridge-group 150 source-learning
no bridge-group 150 unicast-flooding
bridge-group 150 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
interface GigabitEthernet0.11
encapsulation dot1Q 11
no ip route-cache
interface GigabitEthernet0.16
encapsulation dot1Q 16 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface GigabitEthernet0.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
no bridge-group 20 source-learning
bridge-group 20 spanning-disabled
interface GigabitEthernet0.100
encapsulation dot1Q 100
ip address 192.168.100.3 255.255.255.0
no ip route-cache
bridge-group 100
no bridge-group 100 source-learning
bridge-group 100 spanning-disabled
interface GigabitEthernet0.150
encapsulation dot1Q 150
no ip route-cache
bridge-group 150
no bridge-group 150 source-learning
bridge-group 150 spanning-disabled
interface BVI1
ip address 172.17.16.251 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface GigabitEthernet0
access-list 1 permit 172.17.16.1
access-list 1 remark Admin network access
access-list 1 permit 192.168.100.0 0.0.0.255
radius-server attribute 32 include-in-access-req format %h
radius-server host 172.17.21.10 auth-port 1812 acct-port 1813 key 7 047958071C3561410D4A44
radius-server host 172.17.16.12 auth-port 1645 acct-port 1646 key 7 08045E471A48574446
radius-server host 172.17.21.10 auth-port 1645 acct-port 1646 key 7 1320051B185D56797F
radius-server timeout 15
radius-server vsa send accounting
bridge 1 route ip
line con 0
line vty 0 4
access-class 1 in
end

When the issue occurs does that affect both 2.4GHz & 5GHz devices ? I would see which band operating devices affected.
I noticed you have set CH11 under Radio 0 statically. I would prefer to configure it as below so AP can change the channel depend on the environment.
int d0
channel least-congested
HTH
Rasika
**** Pls rate all useful responses ****

I ordered my new S5 online and after following the steps outlined in exact order, my old phone no longer works and the S5 will not authenticate. Now I have no phone and I am becoming frustrating.

I ordered my new S5 online and after following the steps outlined in exact order, my old phone no longer works and the S5 will not authenticate. Now I have no phone and I am becoming frustrating.
It downloaded all my contacts, photo's with no problem. I called the number they gave me from my old phone and then turned it off. I then put the sim card in and charged the phone. I followed all the setup steps and no I cannot send any text or make any phone calls. I get a message that they cannot authenticate my phone to dial #8899 but get the same message.

Hello Notahappycamper1962
Let's get that S5 up and running! I want you to love the S5! Is the old device powered off? What zip code are you in?
I look forward to hearing from you and getting this addressed.
JoeL_VZW
Follow us on Twitter @VZWSupport

Bridge will not open after update.

Adobe Updater did its update and now Bridge will not open. The message is:
The Application Bridge CS3 quit unexpectedly.
I have had to uninstall Photoshop, reinstall photoshop, and then all is well until the Adobe Updater gets going then bang! No more Bridge. The below is the first part of the Apple report.
Any ideas??? Im running 10.5.5 10gigs of ram, on a 8 core Mac.
Process: Bridge CS3 [405]
Path: /Applications/Adobe Bridge CS3/Bridge CS3.app/Contents/MacOS/Bridge CS3
Identifier: com.adobe.bridge2
Version: 2.1.1.9 (2.1.1.9)
Code Type: X86 (Native)
Parent Process: launchd [94]
Date/Time: 2008-10-08 15:53:31.578 -0700
OS Version: Mac OS X 10.5.5 (9F33)
Report Version: 6
Exception Type: EXC_CRASH (SIGABRT)
Exception Codes: 0x0000000000000000, 0x0000000000000000
Crashed Thread: 0

Routine maintenance is imperative.
I still advocate Repairing Permissions (with Apple's Disk Utility) before AND after any system update or upgrade, as well as before AND after installing any software that requires an installer that asks for your password.
I have seen software installations go sour because the installer did not find everything as and where it should be.
I have also seen software installations go bad because the installer did not clean up after itself properly and did not leave everything as and where it should be.
This is just my own personal opinion and practice based on my own observations. Others may disagree and that's OK. I can only base my routines and my advice to others on my own experience and conclusion. I don't pretend to know why others believe otherwise.
Repairing Permissions after the fact (i. e. not immediately before and after an install) seldom helps.; Try it anyway, though.
====
Additionally, if your machine does not run 24/7 so that it runs the daily, weekly and monthly Cron Scripts in the middle of the night as intended by Apple, run Cocktail (shareware) as well.
Cron Scripts are maintenance routines designed by Apple to run on a daily, weekly and monthly basis in the middle of the night.
If you don't run them, you WILL run into trouble, sooner rather than later.
Here's an excerpt from the Apple tech doc
http://docs.info.apple.com/article.html?artnum=107388
Mac OS X performs background maintenance tasks at certain times if the computer is not in sleep mode. If your computer is shut down or in sleep at the designated times, the maintenance does not occur. In that case, you may want or need to run these manually.
Mac OS X periodically runs background tasks that, in part, remove system files that are no longer needed. This includes purging older information from log files or deleting certain temporary items. These tasks do not run if the computer is shut down or in sleep mode. If the tasks do not run, it is possible that certain log files (such as system.log) may become very large.
Also, from:
http://docs.info.apple.com/article.html?artnum=106978
The disk activity generated by find is a normal part of file system maintenance, used for tasks such as removing invisible temporary files that are used by the system. It is scheduled to occur early in the morning at 03:15 everyday, 04:30 on Saturdays, and 05:30 on the first day of each month.
NOTE:
There have been comments to the effect that Apple "fixed" this in 10.4.2 and later versions of the OS, but I have not been able to verify this to my satisfaction. The reference in the 10.4.2 release notes are far from explicit on this subject.
= = =
If you have DiskWarrior, run it regularly too.

Bridge will not launch from task bar or from application. No response at all

bridge will not launch from task bar or from application. No response at all
It was installed from the cloud 2 days ago, it is up to date as is Photoshop also the CC cloud version up to date
it was working yesterday
Photoshop opened with no problem.
Get no response at all...nuttin

In the PSE 12 folder, double click on the Setup.exe
If you get this, just click on Ignore

CS3 Bridge will not launch tried 'ctrl' icon doesn't work.

Adobe Bridge has encountered a problem and needs to close. We are sorry for the inconvenience.
this is the message I get when i try to launch Adobe Bridge -
I called tech support & although I've spent $$$ for master collection CS3 - and so many other adobe programs/software for myself & others.. they are unwilling to offer any support other than a paid issue, which really chafes.
so here I am, throwing seeds into the wind hoping i can get back to work after wasting a nother day with this this.
there is no phantom instance of Bridge.
I have a wacom tablet. I cannot get to any 'preferences' screen with any combination of ctrl, alt, ****..
Bridge will not launch.
Help please? thanks

Curt Y answered this in another thread;
If you can not get the reset window, you are doing something incorrectly.
1. Bridge has to be closed. Check the Task Manager to make sure no copy is running in the background.
2. You have to press and HOLD the Crtl key when you click on the start icon for Bridge.
3. If successful you will get a reset window with 3 options.
in this thread;
http://forums.adobe.com/message/2735898#2735898
the key point is step 2 HOLD... this is nowhere else in the forums..
so, again, thanks to Curt Y for the answer/
I checked all three boxes & Bridge did launch. Why is this so obscure.. and why could tech support just tell me that..
oh well.
again. thanks.

I just installed Photoshop CC 2014, but Latest version of Bridge will not work when I want to open it from PS

Any idea why is Bridge latest version not working when trying to open it in Photoshop CC 2014 ? (French version) ? When trying, Creative Cloud app will open to ask if I want to download newest version, which I did numerous times now.
Thank you
Guy Deschenes
Shawinigan (QC) Canada

Hi Eric,
Here's how a similar problem was resolved between PS and BR.
The issue was confirmed by ChunXiaYang at Adobe staff and solution put in the forum discussion on June 19 (no. 13). Here's a copy:
I have confirmed that this is a known issue before release. And the workaround is to uninstall and reinstall PS 2014. Then Bridge can be launched by selecting 'Browse in Bridge' in PS2014.
Please try the installation, and let me know whether it works. Thanks!
It woks just fine since I unistalled and reinstalled PS 2014.
Guy
Le 2014-07-17 à 1:13 PM, ericboerner a écrit :
I just installed Photoshop CC 2014, but Latest version of Bridge will not work when I want to open it from PS
created by ericboerner in Bridge General Discussion - View the full discussion
I did this with a fresh install of the entire CC package. As soon as the CC packages updated, CC Bridge broke. Unistalled CC PS, reinstalled again, CC Bridge works, but CC PS updates itself again, and breaks CC Bridge.
You know... The whole move to CC has been a massive cluster... I've struggled with the CC packages for my entire subscription year, and now I'm 1.5 month away from needing to throw down another $720 for no reason what-so-ever, just so we can Beta test your really screwed up subscription services.
Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at https://forums.adobe.com/message/6559164#6559164
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page:
To unsubscribe from this thread, please visit the message page at . In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Bridge General Discussion by email or at Adobe Community
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/thread/416458?tstart=0.

I upgraded from PS5 to PS 6 and Bridge will not open in RAW, AMT Failure, also will let me update

I upgraded from PS5 to PS 6 and Bridge will not open in RAW, AMT Failure, also will not let me update and closes Bridge down.
I have uninstalled and reinstalled 3 times and still no success. Any suggestions?

What system are you on? Did you run the Creative Suite Cleaner Tool inbetween your install attempts? If not, try that to produce a "clean" install with factory defaults. Other than that there could be some specific system issues at play, but again, we'd need to actually know what system you are on...
Mylenium

1310 Root Bridge will not Authenticate with 350 Non Root Bridge

Similar Messages

Maybe you are looking for