1310 twinax cable

Hello all, I have aquestion about a 1310 wireless bridge we have installed on top of a 9 story building. It is connected to the injector with a 100ft and a 50ft section of twinax cable with a barrel connector in between them. It has been operating for almost a 9 months very well. Now it only stays up for one or two days. The radio stays connected to the 1310 on the adjacent bulding, it's the ethernet connection from the injector through the twinax cable up to the AP on the roof that fails. We have already replaced the 50ft section of cable. Could it be a moisture/cold problem? If I disconnect the twinax and reconnect it, it comes back up (but only for a day or two).

Yes, I had similar problems with mine. You can check for loose connections or faulty connectors.
Try the following:
>sh int fa0 --> if you see input and CRC errors you are likely having this problem.

Similar Messages

  • 10GE Twinax cables connecting to servers NIC which accept 10GE SFP+

    Anyone has any real life experience of using the Cisco 10GE Twinax cables to connect this to servers with NIC cards that accept SFP+? I'm talking servers like HP and Dell which have 10GE NIC cards. For the switch,  I would be using Nexus 5548UP. The SFP+ part number would be SFP-H10GB-ACU10M.
    The SFP-10G-SR is too expensive and I'm looking at 10GE Twinax cables as an alternative but am quite concerned about the compatability.

    Yes, the twinax cables are all we ever use to connect servers to Nexus 5ks. We have used them with both Qlogic and Emulex CNAs. If the server is more than 10m from the switch the 10G-SR and 50 micron fiber are required.

  • Twinax cable compatibility with 2960X

    Hi,
        I'm trying to connect WS-C2960X-48FPD-L with WS-C4500X-40X-ES via SFP-H10GB-ACU10M (Twinax cable). On 2960X I'm running  15.0(2)EX5 & on C4500X IOS XE 03.06.01.E, now where I use twinax cable on 2960X I get invalid gbic error and port gets error disabled please advise if I'm running the required image and why I'm getting this error.
    Regards,
    Navin RK 

    Hi,
    You are running the required image on both devices.  Does it work if you use a fiber patch cord instead?

  • Connect 4500X with spf+ twinax cables

    Hi what would I need to connect the 4500X with spf+ twinax cables?

    Double check the 10 Gbps transceiver compatibility list. Technically only the 1, 3 and 5m versions are supported.
    I've used them all without any issue in the 4500X. No special commands are necessary.

  • New 10 Meter twinax cable

    According to the updated compatibility matrix, the new 10 Meter twinax SFP-H10GB-ACU10M cable does not show interoperability with the Catalyst 6500 67xx 10 Gig linecards (With CVR-X2-SFP10G converter for X2 ports). The shorter 1-5 meter twinax cables show that they are interoperable.
    http://www.cisco.com/en/US/partner/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_6974.html
    Does anyone know if this is incorrect and just not yet updated.
    Thanks.

    I suspect it might have something to do with the CVR-X2-SFP10G, seeing that the converter module data sheet also does not list any length of the Active Twinax cables being compatible.
    I am trying to reach out to someone within the Product Mgmt org to see if they can provide an answer... but my contacts are old....

  • SFP+ Twinax cable compatibility

    Hi Guys,
    Does anybody know if the 'SFP+ Twinax' active or passive cables are compatable with the HP ethernet 10gb 2-port 530sfp+ adapters? I'm struggling to find/confirm if they are compatible or not.
    Cheers                  

    I've purchased a SFP-H10GB-CU3M (non-branded) TwinAx cable and have successfully connected from a HP NC552SFP 10Gb 2-port adapter (HP DL360p Gen8) into a 3750X (WS-C3750X-24T-S) 10GB (C3KX-NM-10G) module.
    Once I receive my 4500X-16SFP switch, I hope to connect this into 3 dual port 10Gb vSphere hosts as well as my VNX SAN (10Gb SFP).
    Finding anyone from EMC or Cisco that will confirm this solution is possible was impossible...so I hope mine will work!

  • Differance in Active Passive Twinax Cable

    I have 2 Nexus 7000 and 2 Nexus 5000 which connect to FI and the UCS. What I am doing is we purchased the APC racks that allow for able management for the Nexus 7000. I am making the move in a couple step process in order for the least amount of downtime.  The distance from the Nexus equipment will be about 10m away at longest. I see that my Nexus 7000 are connected using the SFP-H10GB-ACU7M and can purchase the  SFP-H10GB-ACU10M. This is an Active cable. But the Nexus 7000 are connected to the Nexus 5000 using the SFP-H10GB-CU5M which is a passive cable. I have been trying to find a CU10M but the longest is 7M. From what I have found on the cisco site at the bottom link. I do not know what the difference is of the Active and Passive cable and having problems googleing what the difference is. Could I get some clarity? 
    http://www.cisco.com/c/en/us/td/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_6974.html
    SFP-H10GB-ACU10M=
    10-m 10G SFP+ Twinax cable assembly, active
    SFP-H10GB-CU5M=
    5-m 10G SFP+ Twinax cable assembly, passive

    passive twinax max distance is 5m, if you need more, e.g. 7 and 10m, you need active twinax.
    Active copper cables contain electrical components in the connectors that boost signal levels. This makes active copper cables slightly more expensive than passive copper cables; however, they can connect the Converged Network Adapter (CNA) to a top-of-the-rack switch over longer distances than passive copper cables.
    http://www.cisco.com/c/en/us/products/collateral/interfaces-modules/transceiver-modules/data_sheet_c78-455693.html

  • Cisco Twinax Cables Compatibiltiy with EMC VNX/VNXe

    Hi,
    I would like to know about Cisco Twinax Cables Compatibiltiy with EMC VNX/VNXe series storage - for connectivity between UCS Fabric Interconnect and EMC VNX/VNXe.
    Are the following Cisco Twinax Cables compatible with EMC's VNX and VNXe serie platforms:
    SFP-H10GB-CU1M= 1-m 10G SFP+ Twinax cable assembly, passive
    SFP-H10GB-CU3M= 3-m 10G SFP+ Twinax cable assembly, passive
    SFP-H10GB-CU5M= 5-m 10G SFP+ Twinax cable assembly, passive
    SFP-H10GB-ACU7M= 7-m 10G SFP+ Twinax cable assembly, active
    SFP-H10GB-ACU10M= 10-m 10G SFP+ Twinax cable assembly, active
    Kindly advice. Thanks.

    Hi,
    I'd like to confirm you, that passive assembly is supported. Haven't tried the actives one yet.
    I'm using UCS-B200 M3, and EMC VNX 5300.
    the EMC VNX5300 (Block Level) connected using 2 type of media. Copper (SFP-H10GB-CU5M= 5-m 10G SFP+ Twinax cable assembly, passive) and Fiber Channel 8 GB directly info Fabric Interconnect 6248 ports.
    For old server the connection is via iSCSI 10GB Copper. and for UCS-B200 M3 is via FC 8GB.
    All my configuration is running well.
    Hope thats helped.
    Thanks,
    Pieter

  • 5548UP / N2K-C2248TP-E-1GE - Twinax cable 10Gbase-(unknown)

    HI,
    Just building some 5548UP's with N2K-C2248TP-E-1GE Fex's and we're using Cisco Twinax cables to connect between the 5K's and 2K's (part number SFP-10G-AOC2M).
    All interfaces are up and seem to be working ok, no errors etc.  But when we do a show int status the SFP's are showing as type unknown.
    Is this an issue.?
    Ethernet1/11
        transceiver is present
        type is 10Gbase-(unknown)
        name is CISCO-AVAGO
        part number is AFBR-7CER02Z-CS1
        revision is B1
        serial number is AVE1742K01J-A
        nominal bitrate is 10300 MBit/sec
        Link length supported for copper is 2 m
        cisco id is --
        cisco extended id number is 4
    SFP calibration is invalid

    There was qos configuration missing. After configuring this:
    system qos
      service-policy type qos input system_qos_policy
      service-policy type queuing input system_q_in_policy
      service-policy type queuing output system_q_out_policy
      service-policy type network-qos system_nq_policy
    The FCoE ports are up !!!
    Regards Jiri

  • Twinax cable Nexus 5000

    Hi,
    According to this matrix the Nexus 5000 don't support 2meters Twinax SFP+ cable.
    http://www.cisco.com/en/US/prod/collateral/switches/ps9441/ps10110/data_sheet_c78-568589.html
    Does anyone know why?
    Thanks
    Mattias

    Thanks!  I thought it should be resolved in a later release. And I didn't know 6.0 was released.
    Do you also know when (or if it's already is) 2meters is supported in UCS Fabric Interconnect 6200?
    http://www.cisco.com/en/US/docs/unified_computing/ucs/hw/6200/install/overview.html#wp1219488
    And Cisco UCS C CNA VIC 1225
    http://www.cisco.com/en/US/prod/collateral/ps10265/ps10493/C220M3_SFF_SpecSheet.pdf
    Page 27
    Br,
    Mattias

  • NAS & N7K cabling issue

    I am having an issue with connectivity between NAS box (QNAP TS-EC1279U-RP) and Nexus 7K.
    I have a NAS device with 2 * 10G Copper ports which will be connected to Nexus 7K via patch panels. All the ports on my 7K are SFP+ ports and I need to find an SFP or converter or a cable which will support this setup and run at 10G without interoperability issues.
    Can someone suggest any coverter, or anything else quickly. I heard about Twinax cables but not sure about the same.
    What considerations, issues should I keep in mind with the same.?

    The link that was posted to contact Openreach is the correct contact point as it is damaged Openreach infrastructure and nothing to do with BT Retail your service provider this is the actual page you need to use faulty line
    Plant
    http://www.openreach.co.uk/orpg/home/submitFeedback.do?contactReason=complain_damage_external_line_p...
    Only Openreach can deal with this you will not be charged for the visit
    The statement applies to line faults and internal wiring faults Not line plant problems
    If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

  • TwinAx 10GB Nics

    I am trying to push a Nexus solution in the Datacentre, but I am having trouble getting a list of 10GB NICS (not CNA) that I can use the Cisco Twinax cable with.
    Does anybody have a list?

    Cisco has their own SFP/SFP+ modules & cables, however you may need to check the chipset on the TwinAx cables as some passive twinAx are not compatible with certain HP network adapters or SAN solution i.e. EMC.
    http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/installation/note/78_15160.html
    http://www.cisco.com/en/US/prod/collateral/modules/ps5455/data_sheet_c78-455693.html

  • Active Twinax

    Looking at the transceiver support matrix for the Fabric Interconnects I do not see the 7m or 10m Active Twinax cables listed, suggesting that 5m is the maximum cable length for copper. However the longer Active Twinax cables are listed as an option in DesignXpert. Can anyone confirm that Active Twinax cables will actually work for connecting the FEX to the FI and are fully supported by TAC? Or is there a good reason why they have been left of the support matrix?
    Table 3 here: http://www.cisco.com/en/US/prod/collateral/ps10265/ps10276/data_sheet_c78-524724.html
    Thanks

    Hubert,
    They're in the compatibility matrix but only show being supported by NX-OS 4.2(1)N2(1)
    http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_6974.html
    I don't know about the Bit Error Rate though.  The fact that they're supported in 4.2.1 but not in 5.x makes me think its a testing thing rather than a functional BER thing.  I could be wrong on that though.  Short answer is not supported.
    --Justin

  • Catalyst 4900M OneX & Twinax

    I am trying to connect a Nexus 5548UP to a Catalyst 4900M using Twinax. 
    On the 4900M I am using a OneX converter (CVR-X2-SFP10G) to provide me with the necessary SFP+ port.  I am using a 3m Twinax for the link (
    SFP-H10GB-CU3M=)
    The 4900M recognizes the OneX but does not recognize the Twinax.  If I switch to using 10GB-SR fiber SFPs everything works, but we are trying to move exclusively to Twinax. 
    I found a post from 2009 (here) which mentioned some compatibility issues with Twinax on the 4900M with OneX and that the poster was working with Cisco.   Does this incompatibility still exist?   Both the 4900M and Twinax are on the compatibility matrix for the OneX module.
    Thanks!

    this needs a v -02 twinax cable. possibly we have a older version twinax and that might wont work.
    http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_6974.pdf
    please look at table 5 and the note below it.
    Thanks, Vin

  • Cisco NAM2320 SFP+/Twinax compatibility

    Hi,
    Is the NAM2320 Compatible with the below Twinax Cables?
    SFP-H10GB-CU1M
    SFP-H10GB-CU3M
    SFP-H10GB-CU5M
    SFP-H10GB-ACU10M

    Hi Edward,
    The Cisco 2300 installation guide contains a warning in the Requirements and Restrictions as well as the Connecting the Ports - Direct Connections section as follows:
    WARNING: Do not use a SFP-H10GB-CU5M (Cisco part) cable to connect a switch and a Cisco Prime NAM 2320
    appliance.
    There may be more details in the bug tracker regarding this issue.
    You can find the NAM 2300 Installation and Configuration Guide here: http://www.cisco.com/en/US/partner/docs/net_mgmt/network_analysis_module_appliance/2300/installation/guide/adeins.html#wp1098026

Maybe you are looking for

  • Problem with Adobe Forms

    I am getting error with ADS Forms. Please find the logs. Date , Time , Message , Severity , Category , Location , Application , User10/28/2009 , 13:00:29:567 ,  [EXCEPTION] com.sap.engine.services.ejb.exceptions.BaseEJBException: Transaction system f

  • S10-3 Wifi Problem in Quick Start OS (Splashtop​)

    I just got my S10-3 on last Saturday, and I found out that the wifi is keeping disable in Quick Start OS. No matter I press Fn+F5 or switch the wifi button, the Wifi cannot be enabled in Quick Start OS. But everything is alright in Windows. I guess i

  • Automated email to buyer, when email/FAX fail to vendor for a PO

    Hi All, If an email/FAX failed to transmit to the vendor for a PO, will there be a way (method) to give an email notification in buyer's inbox ?? Please provide details. Thanks!! Vivek.

  • MDM integrity between SRM and R/3

    Hi All, How MDM integrity of the process validations being made between SRM and R/3 for the creation of different documents. Please share me any documents regarding MDM intergirty between SRM and R/3. This is not related to Catalogs, 1. Creation of d

  • CAN CF8 REPORT BUILDER  SUPPORT PDF CHINESE VERSION FILE?

    why the report builder of coldfusion 8 can not support the PDF chinese version files? Does it need install any other plugin to support it? Thanks advance for your reply!